# Agricultural Technology Grade 12 NSC June 2021 Memo (Eng)

> Grade 12 Agricultural Technology memorandum from the NSC June Exam 2021 (English), 13 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/agricultural-technology-may-june-2021-mg-eng/bb8abf1f-a9c0-4d72-915e-31e75ca3201d
- Updated: 2026-10-29
- Subject: Agricultural Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2021
- Exam period: NSC June Exam
- Curriculum: CAPS
- Pages: 13

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Agricultural Technology](https://www.hlayiso.com/library/grade-12/agricultural-technology) › [Agricultural Technology Grade 12 NSC June 2021 Memo (Eng)](https://www.hlayiso.com/library/agricultural-technology-may-june-2021-mg-eng/bb8abf1f-a9c0-4d72-915e-31e75ca3201d)

## About this document

Agricultural Technology · Grade 12 · NSC June Exam · 2021. Memorandum. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

             SENIOR CERTIFICATE EXAMINATIONS/
         NATIONAL SENIOR CERTIFICATE EXAMINATIONS

                          AGRICULTURAL TECHNOLOGY

                                          2021

                               MARKING GUIDELINES

                                                                       MARKS: 200

                      This marking guideline consists of 13 pages.

Copyright reserved                                                   Please turn over

### Page 2

Downloaded from hlayiso.com
Agricultural Technology                           2                             DBE/2021
                                      SC/NSC – Marking Guidelines

SECTION A

QUESTION 1

1.1       1.1.1           C                                                                 (2)

          1.1.2           D                                                                 (2)

          1.1.3           C                                                                 (2)

          1.1.4           A                                                                 (2)

          1.1.5           B                                                                 (2)

          1.1.6           D                                                                 (2)

          1.1.7           B                                                                 (2)

          1.1.8           D                                                                 (2)

          1.1.9           B                                                                 (2)

          1.1.10          C                                                                 (2)
                                                                                              [20]

1.2       1.2.1           Stress/Depression/anxiety                                         (2)

          1.2.2           Gearbox/Gears/Transmission                                        (2)

          1.2.3           Magnetism/decrease rusting                                        (2)

          1.2.4           Explosion/Fire                                                    (2)

          1.2.5           Simultaneously/together/All at once                               (2)
                                                                                              [10]

1.3       1.3.1           F                                                                 (2)

          1.3.2           A                                                                 (2)

          1.3.3           C                                                                 (2)

          1.3.4           D                                                                 (2)

          1.3.5           B                                                                 (2)
                                                                                (5 x 2)       [10]

                                                                    TOTAL SECTION A:          40

Copyright reserved                                                         Please turn over

### Page 3

Downloaded from hlayiso.com
Agricultural Technology                              3                                    DBE/2021
                                         SC/NSC – Marking Guidelines

SECTION B

QUESTION 2: MATERIALS AND STRUCTURES

2.1       2.1.1           A metal that will be used to supply warm water.

                          Copper.                                                                     (1)

          2.1.2           The reason why Copper will be the best suited for warm water
                          pipes.

                          No corrosion/rust.                                                          (1)

          2.1.3           The joining method that will be used to permanently join two
                          Copper pipes.

                          Soldering.                                                                  (1)

          2.1.4           The material that will be best to transport milk in a dairy system.

                          Stainless steel.                                                            (1)

          2.1.5           A reason why stainless steel will be the best metal.

                          The steel is resistant to air, water and many chemicals used for
                          cleaning/Corrosion resistant/Hygienic/does not contaminate food.            (1)

          2.1.6           A method used to permanently join stainless steel.

                          Welding/TIG welding.                                                        (1)

          2.1.7           The best metal used for the manufacturing of a farm gate.

                          Mild steel.                                                                 (1)

          2.1.8           The substance that can corrode copper.

                          Acids/Ammonium/Heavy metal salts/Sulphur.                                   (1)

          2.1.9           A metal that is commonly used in the food industry for food storing
                          purposes.

                          Aluminum.                                                                   (1)

2.2       THREE preparation procedures to ensure a sufficient PVC pipe welding joint.

              Make sure the joint is clean.
              Make sure the joint is dry.
              Sand both the joint with sandpaper.                                                    (3)

Copyright reserved                                                                  Please turn over

### Page 4

Downloaded from hlayiso.com
Agricultural Technology                            4                                    DBE/2021
                                       SC/NSC – Marking Guidelines

2.3       2.3.1           Description of the earth leakage system of the electrical fence.

                             There must be an earth spike to the ground to complete the
                              circuit between the ground and the fence.
                             The animal or person will complete the circuit and get
                              shocked.
                             Plant material will influence the circuit and must be removed.
                             Inspect the fence, isolators and connections frequently to
                              prevent short circuit.
                             Run an earth return line parallel to the fence line on long
                              distance fences.
                             Connect with earth spikes on a regular basis to improve the
                              efficiency.                                                            (6)

          2.3.2           The type of wire that may never be used to erect an electric fence.

                             Razor wire.
                             Barbed wire.                                            (Any 1)        (1)

          2.3.3           TWO daily activities that the farmer must perform to properly
                          maintain an electric fence.

                             Clean plants that is touching the fence.
                             Look for damaged or broken wires, isolators or loose
                              connections and repair.                                                (2)

2.4       Recommendations for the use of Vesconite when manufacturing bushes.

              Easy to install or to remove.
              Does not corrode and is non-conductive.
              Will not wear shafts.
              Resistant to a wide range of chemicals.
              Cheap to manufacture.                                                                 (5)

2.5       ONE electrical property of Teflon and a reason for the answer.

              It has a high di-electric capacity.
              Reason: Electricity don’t have an influence on this material.                         (2)

2.6       FIVE properties of safety screens on a combine harvester.

              Light.
              Safeguard the user.
              Not vibrate or become loose.
              Sturdy/Strong.
              Keep out all undesired material.                                                      (5)

Copyright reserved                                                                 Please turn over

### Page 5

Downloaded from hlayiso.com
Agricultural Technology                            5                                       DBE/2021
                                       SC/NSC – Marking Guidelines

2.7       TWO reasons for the use of brass instead of copper in the manufacturing of
          electrical connections.

              Hardness.
              Strength.
              Machinability.
              Wear resistance.
              Ductility.                                                                (Any 2)      (2)
                                                                                                       [35]

QUESTION 3: ENERGY

3.1       TWO alternative energy sources that make use of a turbine and a generator
          to generate electricity.

              Wind.
              Geothermal.
              Hydro.                                                                    (Any 2)      (2)

3.2       3.2.1           The number of systems that you will need to provide sufficient
                          power to a 6 kw submersible pump.

                          Two.                                                                        (1)

          3.2.2           Determine whether the panels should be connected in parallel or
                          series and a reason for the answer.

                          Series. Because a connection in series will increase the
                          kw/power twice.                                                             (2)

          3.2.3           ONE Reason for the use of silicon in the manufacturing of the solar
                          cells.

                             Is a semi conductive material.
                             Can withstand the temperature of the sun.
                             Don't conduct heat.
                             Is water tight/proof.                                      (Any 1)      (1)

          3.2.4           The layer of the solar panel that carries negative electrons.

                          The top layer/N-Type layer.                                                 (1)

          3.2.5           Measure to ensure that there is electricity available during the
                          night.

                          Use a battery system for the night.                                         (1)

Copyright reserved                                                                  Please turn over

### Page 6

Downloaded from hlayiso.com
Agricultural Technology                           6                                 DBE/2021
                                      SC/NSC – Marking Guidelines

          3.2.6           THREE applications of solar panels on a game farm.

                             To provide power to: security cameras.
                             Alarm systems.
                             Electric gate motors.
                             Emergency lights.
                             Electric fencing.
                             Borehole pumps.                                     (Any 3)        (3)

3.3       FOUR advantages of geothermal power station.

              No pollution.
              The cost of the land to build a geothermal power plant on is usually less
               expensive.
              Clean energy.
              Tax cuts.
              No fuel is used to generate electricity.
              Low running cost.                                              (Any 4)            (4)

3.4       FOUR factors that must be considered when installing a small wind turbine on
          a farm.

              Must be in an open space/field.
              Flat area.
              The absence of obstacles like trees/forests/hills/mountains.
              The presence of strong and frequent winds.
              A location further from a village or residential site.
              Location away from suburbs. 
              Not harmful to bird life or nature.                                (Any 4)        (4)

3.5       Process used to manufacture ethanol.

          Distillation.                                                                          (1)
                                                                                                  [20]

Copyright reserved                                                             Please turn over

### Page 7

Downloaded from hlayiso.com
Agricultural Technology                           7                                        DBE/2021
                                      SC/NSC – Marking Guidelines

QUESTION 4: SKILLS AND CONSTRUCTION PROCESSES
4.1                                          Welding defect         Gee moontlike oorsake
                                             4.1.1                  4.1.2
                                             Porosity.              Blocked nozzle.
                                                                     Gas flow too low or too
                                                                        high.
                                                                     Leaking gas lines.
                                                                     Draught conditions.
                                                                     Nozzles distance from
                                                                        the work is too great.
                                                                     Painted, wet or oily
                                                                        plate.
                                                                     Wet or rusty
                                                                        electrode/wire.
                                                                                        (Any 1)
                                             4.1.3                  4.1.4
                                             Spatter.               Voltage too low.
                                                                     Inadequate
                                                                        inductance
                                                                     Rusty or dirty plate.
                                                                                         (Any 1)

                                             4.1.5                  4.1.6
                                             Undercut.              Welding speed too
                                                                        fast.
                                                                     Current too high.
                                                                     Poor technique.
                                                                                      (Any 1)

                                             4.1.7                  4.1.8
                                             Lack of                 Amps too low.
                                             fusion.                Irregular surface.
                                                                     Wrong torch angle.
                                                                                      (Any 1)
                                                                                                         (8)
4.2       MIG welding labels for the numbers A–D as indicated.
          A – Molten puddle.
          B – Contact tip.
          C – Welding wire/Electrode.
          D – Shielding gas.                                                                            (4)
4.3       4.3.1           TWO materials that can be cut with oxy-acetylene cutting
                          apparatus.
                             Mild steel.
                             Cast iron.
                             Stainless steel.                                           (Any 2)        (2)

Copyright reserved                                                                    Please turn over

### Page 8

Downloaded from hlayiso.com
Agricultural Technology                               8                                        DBE/2021
                                          SC/NSC – Marking Guidelines

          4.3.2           FIVE steps that must be followed to cut a straight line on a 10mm
                          mild steel sheet using an Oxy-acetylene cutting apparatus.

                                 Attach an guide iron to the metal sheet next to the place where
                                  you want to cut/parrallel to your mark.
                                 Select the appropriate nozzle size.
                                 Light the torch and adjust the required flame.
                                 Bring the material up to red-hot.
                                 Oxygen is then fed with the lever on the cutting attachment.
                                 Move the torch at the required speed along a guide.
                                 The oxygen will blow the melted iron from the cutting area to
                                  create a clean cutting line.                           (Any 5)         (5)

          4.3.3           THREE oxy-acetylene welding tips in the overhead welding
                          position.

                                 Reduced melting pool just big enough to create the wanted
                                  penetration.
                                 Reducing the size of the flame.
                                 Use a slightly thicker welding rod.
                                 Use the force of the flame to keep the molten metal in
                                  position.                                         (Any 3)              (3)

4.4       Marks will be allocated for the following:
              Design                           2
              Correct scale                    1
              Dimensions                       2
              Neatness                         1

                                                           1200 
          Neatness            
          Design      

                                                                                     600   

                                                                                   900

          Scale = 1:100 

                                                                                                          (6)

Copyright reserved                                                                   Please turn over

### Page 9

Downloaded from hlayiso.com
Agricultural Technology                            9                                      DBE/2021
                                       SC/NSC – Marking Guidelines

4.5       A gas that can be used with a plasma cutter to remove the melted metal.

                Argon.
                Nitrogen.
                Oxygen.
                Compressed air.                                                        (Any 1)       (1)

4.6       Comparison in table form of the Inverter welding machine to the MIG welding
          machine

              Inverter welder                         MIG welding machine
                Low initial setup cost.              High initial setup cost.
                Compact.                             Bulk or large.
                Light and easy to handle.            Heavy and difficult to handle.
                Slag must be removed after            No slag.
                 welding.
                No additional shielding gas           Need additional cylinder for the
                 cylinder needed.                      shielding gas.
                Lower maintenance cost.              High maintenance cost.
                                                                                      (Any 6)          (6)
                                                                                                       [35]

QUESTION 5: TOOLS, IMPLEMENTS AND EQUIPMENT

5.1       5.1.1           Identification of the component in the sketch that serves as a
                          connection between the parts.

                          Universal joint.                                                            (1)

          5.1.2           The substance that is used to lubricate the universal joint.

                          Grease.                                                                     (1)

          5.1.3           ONE application of the universal joint.

                             Drive shaft.
                             Power take off shaft.
                             Steering mechanism.                                       (Any 1)       (1)

          5.1.4           TWO mechanisms installed in the drive system of a four-wheel
                          drive vehicle that allows disconnection of drive to the front wheels
                          and ONE advantage of each device.

                             4 x 4 Gearbox. 4 x 4 can be disengaged when driving on tar
                              roads.
                             Front wheel hub locking devices. Wear is reduced on the
                              front wheels and front wheel system.                                    (4)

Copyright reserved                                                                  Please turn over

### Page 10

Downloaded from hlayiso.com
Agricultural Technology                            10                                     DBE/2021
                                        SC/NSC – Marking Guidelines

5.2       Type of hydraulic cylinder used to lift or lower the fork of the baling machine.

          Double action hydraulic cylinder.                                                            (1)

5.3       Function of the lining on the friction plate of a clutch.

              Prevents the pressure plate from slipping.
              Heat resistant/Wear resistant.                                           (Any 1)        (1)

5.4       TWO advantages of the diff lock as found on a 4x4 tractor.

              Provide increased traction/torque.
              Both wheels turn together regardless of traction available to each.
              Each wheel applies rotational force independent of the available
               traction.                                                         (Any 2)               (2)

5.5       ONE advantage of a bearing without a grease nipple.

              Comes lubricated from manufacturer.
              No additional greasing needed.
              Sealed bearing.                                                         (Any 1)         (1)

5.6       5.6.1           Calculation of the pulley ratio of the electrical motor to the pump.

                          Driven pulley
                          Drive pulley
                            450mm
                            150mm
                            = 3
                           Ratio: 3:1                                                                  (3)

          5.6.2           FOUR reasons for using a V-belt instead of a flat belt.

                             V-belts do not slip off pulleys.
                             V-belts draw tighter around a pulley when tension increases.
                             Lubrication is never necessary.
                             V-belts are relatively strong, and under normal circumstances
                              do not easily break.
                             V-belts last longer than flat belts.
                             Cold, moist conditions, age or use do not cause V-belts to
                              stretch or shrink.                                    (Any 4)            (4)

          5.6.3           Part that allows relative rotation to the rotor shaft.

                          Bearing.                                                                     (1)

Copyright reserved                                                                   Please turn over

### Page 11

Downloaded from hlayiso.com
Agricultural Technology                          11                                  DBE/2021
                                      SC/NSC – Marking Guidelines

5.7       FOUR possible faults in the engine that can cause the presence of oil in the
          combustion chamber.
              Piston rings are worn.
              Cylinder gasket blown.
              Crack in cylinder head.
              Cylinder sleeves/walls are worn.
              Valve stem seals perished/worn.                                     (Any 4)        (4)
5.8       Properties of a functional clutch.
              It should engage smoothly and not jam, slip or shudder.
              It should be capable of transferring the maximum load of the engine
               without slip.
              When the clutch is disengaged, it should do so completely and not tend
               to drag.
              The clutch should be of such a nature that it could be engaged or
               disengaged comfortably by hand or foot.
              The friction material used on the clutch plate should not only be highly
               wear and temperature resistant.                                                    (5)
5.9       FOUR parts that must be examined on a second hand tractor before you
          decide to buy it.
              Engine.
              Gearbox.
              Final drive.
              Cooling system.
              Fuel system.
              Steering mechanism.
              Instruments.
              Battery.                                                            (Any 4)        (4)
5.10      Function of the parts of a hammer mill.
          5.10.1          The hopper: Facilitates the process of feeding.                         (1)
          5.10.2          Cyclone: Separates the grounded material from the air.                  (1)
5.11      Reason for the wheels of a front-end loader to be set at its widest position.
          To increase stability.                                                                  (1)
5.12      Servicing procedure when preparing a combine harvester for the harvesting
          season.
              Lubricate/Grease all moving parts.
              Correct tension of belts and chains.
              Check that all parts are functioning by operating it slowly.
              Replace all worn parts.
              Service according to manufacturer's specifications.
              Lift up all dust release guards.
              Check that no blades are damaged and are sharp.                     (Any 4)        (4)
                                                                                                   [40]

Copyright reserved                                                              Please turn over

### Page 12

Downloaded from hlayiso.com
Agricultural Technology                       12                                     DBE/2021
                                   SC/NSC – Marking Guidelines

QUESTION 6: WATER MANAGEMENT

6.1       FOUR factors to be considered before deciding on a relevant irrigation
          method.

               Type of crop that must be irrigated.
               Determine the amount of water that is available.
               Type of irrigation system.
               Type of pump.
               Determine the water flow (LPM) and pressure requirements.
               Size of the field.
               Create the first irrigation design.                                (Any 4)        (4)
6.2       Goals of irrigation scheduling.

               To apply adequate water to the root zone of the plant.
               Prevent overwatering.
               Allow the soil to dry out in between watering.
               To allow air to enter the soil.                                    (Any 3)        (3)
6.3       TWO structural problems that can influence the sprinkler.

               The springs can lose tension or break.
               The nozzles can be blocked.
               The water pressure is inadequate.                                  (Any 2)        (2)
6.4       A device that a farmer can use to measure the evaporation tempo in a maize
          field.

          Evaporation pan/Class A evaporation pan.                                                (1)
6.5       Labelled drawing of a French water drainage system.
          Marks will be allocated for:

              Design 1
              Drawing 1
              Labels  4

                               Trench /Furrow                  Gravel/Stone

        Perforated pipe/Pipe
                                                  Permeable membrane
                                                                                                   (6)

Copyright reserved                                                              Please turn over

### Page 13

Downloaded from hlayiso.com
Agricultural Technology                          13                                    DBE/2021
                                      SC/NSC – Marking Guidelines

6.6       FIVE items that should never be disposed off in a septic tank.

              Cigarette butts.
              Sanitary pads/towels. 
              Detergents.
              Fats and oils.
              Laundry waste.
              Plastics.                                                            (Any 5)      (5)

6.7       THREE reasons to determine the flow rate in a pipe delivery system.

              For correct calibrating of the sprayers.
              For effective scheduling of irrigation.
              To prevent the over utilisation of the water source.                              (3)

6.8       6.8.1           THREE advantages of a centre pivot irrigation system.

                             No labourer needed to shift the pipes/system.
                             One-man operation.
                             Automated watering system/scheduling.
                             Pesticides/fertilizers are applied through the system. (Any 3)     (3)

          6.8.2           THREE design principles that are built into the centre pivot
                          irrigation system to ensure uniform distribution of water.

                             Distribution pattern of the sprayers.
                             Nozzle opening diameter must increase proportionally further
                              from the centre to allow for a higher water application.
                             Spacing between sprayers must decrease proportionally
                              further from the centre.                                           (3)
                                                                                                  [30]

                                                                        TOTAL SECTION B:          160
                                                                           GRAND TOTAL:           200

Copyright reserved

## Related documents

- [Agricultural Technology May June 2021 MG Afr](https://www.hlayiso.com/library/agricultural-technology-may-june-2021-mg-afr/427a8975-2250-4eaa-98ec-79fd8d83222d) — Agricultural Technology · Memo · 2021 · Afr
- [Agricultural Technology May June 2021 Afr](https://www.hlayiso.com/library/agricultural-technology-may-june-2021-afr/7ffbeef7-3f87-4cff-a5d4-5a92f3861dd1) — Agricultural Technology · QP · 2021 · Afr
- [Agricultural Technology May June 2021 Eng](https://www.hlayiso.com/library/agricultural-technology-may-june-2021-eng/3f54a9c3-3e0a-4cf0-a219-4664361b8bd4) — Agricultural Technology · QP · 2021 · Eng
- [Agricultural Technology Nov 2021 MG Eng](https://www.hlayiso.com/library/agricultural-technology-nov-2021-mg-eng/e95c9d3e-42d8-4b28-93e1-74c3dbc81895) — Agricultural Technology · Memo · 2021 · Eng
- [Agricultural Technology Nov 2021 MG Afr](https://www.hlayiso.com/library/agricultural-technology-nov-2021-mg-afr/b56ea494-1ea0-4d26-859f-b3a8c275c181) — Agricultural Technology · Memo · 2021 · Afr
- [Agricultural Technology Nov 2021 MG Eng](https://www.hlayiso.com/library/agricultural-technology-nov-2021-mg-eng-1/e56e9c83-29a3-414a-bec7-7b25adaa372f) — Agricultural Technology · Memo · 2021 · Eng

## More from Grade 12 Agricultural Technology

- [Gr 12 Agric Tech ATP 2023-24](https://www.hlayiso.com/library/gr-12-agric-tech-atp-2023-24/9d982b07-0af2-4c43-8efe-886b4631bf17) — ATP
- [Agricultural Technology May-June 2025 Eng](https://www.hlayiso.com/library/agricultural-technology-may-june-2025-eng/277bcb3f-14d3-4d58-9b23-d192269c80e2) — QP · 2025 · Eng
- [Agricultural Technology Nov 2025 Eng](https://www.hlayiso.com/library/grade-12-agricultural-technology-2025-nsc-november-exam-question-paper/d47614f1-1c99-4acc-87f4-eefd7c63d61e) — QP · 2025 · Eng
- [Agricultural Technology Nov 2025 Afr](https://www.hlayiso.com/library/grade-12-agricultural-technology-2025-nsc-november-exam-question-paper/f45f941f-dd15-410f-97ae-f0ce8a673078) — QP · 2025 · Afr
- [Agricultural Technology Nov 2024 Afr](https://www.hlayiso.com/library/agricultural-technology-nov-2024-afr/f4723cfb-5760-424c-a00a-2c0e3b5e5dbb) — QP · 2024 · Afr
- [Agricultural Technology Nov 2024 Eng](https://www.hlayiso.com/library/agricultural-technology-nov-2024-eng/f63c1a66-fac4-4a77-acdc-6e16d5d7293f) — QP · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
