# Agricultural Technology Grade 12 November 2024 NSC QP (Eng)

> Grade 12 Agricultural Technology question paper from the November 2024 NSC (English), 15 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/agricultural-technology-nov-2024-eng/f63c1a66-fac4-4a77-acdc-6e16d5d7293f
- Updated: 2026-09-27
- Subject: Agricultural Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 15

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Agricultural Technology](https://www.hlayiso.com/library/grade-12/agricultural-technology) › [Agricultural Technology Grade 12 November 2024 NSC QP (Eng)](https://www.hlayiso.com/library/agricultural-technology-nov-2024-eng/f63c1a66-fac4-4a77-acdc-6e16d5d7293f)

## About this document

Agricultural Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 15 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Confidential

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

                       AGRICULTURAL TECHNOLOGY

                               NOVEMBER 2024

MARKS: 200

TIME: 3 hours

                     This question paper consists of 15 pages.

Copyright reserved                                               Please turn over

### Page 2

Agricultural Technology                        2                         DBE/November 2024
                                         NSC Confidential

INSTRUCTIONS AND INFORMATION

1.        GENERAL INSTRUCTIONS AND INFORMATION

          1.1        This question paper consists of TWO sections, namely SECTION A
                     and SECTION B.

          1.2        BOTH sections are COMPULSORY.

          1.3        Answer ALL the questions in the ANSWER BOOK.

          1.4        Number the answers correctly according to the numbering system
                     used in this question paper.

          1.5        You may use a non-programmable calculator.

          1.6        Show ALL calculations.

          1.7        Write neatly and legibly.

2.        SECTION A: SHORT QUESTIONS

          2.1        This section consists of THREE questions.

          2.2        Follow the instructions when answering the questions.

3.        SECTION B: STRUCTURED LONG QUESTIONS

          3.1        This section consists of FIVE questions.

          3.2        Start EACH question on a NEW page.

Copyright reserved                                                           Please turn over

### Page 3

Agricultural Technology                             3                          DBE/November 2024
                                              NSC Confidential

SECTION A

QUESTION 1

1.1       Various options are provided as possible answers to the following questions.
          Choose the answer and write only the letter (A–D) next to the question
          numbers (1.1.1 to 1.1.10) in the ANSWER BOOK, e.g. 1.1.11 D.            Nov

          1.1.1           A device used for determining the grazing pattern of a farm animal:

                          A   Two-way radio
                          B   GPS
                          C   VRT
                          D   RFID

          1.1.2           A water purification method that sends water through two different
                          liquids, separated by a permeable film, that allows water to pass
                          through on a molecular level:

                          A   Sand filter
                          B   Water softener
                          C   Carbon filter
                          D   Reverse osmosis

          1.1.3           Insufficient … will cause splattering of little metal balls during the
                          welding process and will discolour the welding joint into colours of
                          brown and green.

                          A   wire speed
                          B   shielding gas
                          C   amperage
                          D   heat

          1.1.4           ONE of the following is NOT part of the three-point hitch
                          mechanism of a tractor:

                          A   Levelling box
                          B   Lifting arms
                          C   PTO shaft
                          D   Stabilising chains

          1.1.5           Movable capital includes implements and …

                          A   fuel.
                          B   boreholes.
                          C   farm tools.
                          D   repairs.

Copyright reserved                                                                      Please turn over

### Page 4

Agricultural Technology                           4                           DBE/November 2024
                                            NSC Confidential

          1.1.6           The function of the automatic depth-control mechanism of a tractor
                          is to adjust the …

                          A   rear end of the plough.
                          B   ploughing depth according to the soil conditions.
                          C   angle of the implement in relation to the tractor's movement.
                          D   cross angle of the implement in relation to the tractor.

          1.1.7           … is any plant or animal matter that is combustible and which can
                          be used as an alternative fuel.

                          A   Biofuel
                          B   Coal
                          C   Fossil fuel
                          D   Petroleum

          1.1.8           The process of joining brass:

                          A   Silver soldering
                          B   Brazing
                          C   Plasma joining
                          D   MIG welding

          1.1.9           ONE of the following must be considered when choosing an
                          adhesive for application in conditions where extreme heat plays a
                          major role:

                          A   Heat resistance
                          B   Flammability
                          C   Combustibility
                          D   All the above-mentioned

          1.1.10          … is used as a non-stick material for manufacturing windshield
                          wiper blades.

                          A   Bakelite
                          B   Teflon
                          C   Vesconite
                          D   PVC                                                     (10 x 2)       (20)

Copyright reserved                                                                Please turn over

### Page 5

Agricultural Technology                            5                            DBE/November 2024
                                             NSC Confidential

1.2       Change the underlined word in the following to make the statements TRUE.
          Write only the appropriate word next to the question numbers (1.2.1 to 1.2.5)
          in the ANSWER BOOK, e.g. 1.2.6 Tractor.

          1.2.1           A spur gear runs at an angle across the outer circumference of the
                          gear.

          1.2.2           Hydro energy is extracted from deep under the Earth's surface and
                          is regarded as one of the most sustainable energy sources.

          1.2.3           The side of a hydraulic cylinder, which contains the piston, creates
                          a much weaker pushing force than the opposite side.

          1.2.4           Electrical fences should not be erected diagonally under overhead
                          power lines.

          1.2.5           A streak of lightning always finds the longest path to the ground.
                                                                                         (5 x 2)       (10)

1.3       Choose a word/term from COLUMN B that matches a description
          in COLUMN A. Write only the letter (A–I) next to the question numbers
          (1.3.1 to 1.3.5) in the ANSWER BOOK, e.g. 1.3.6 J

                           COLUMN A                                  COLUMN B
          1.3.1      A device that produces electrical      A   standardisation
                     energy through photovoltaic
                     technology                             B   wind turbines

          1.3.2      An example of pneumatic                C   inverter
                     equipment used in a farm
                     workshop                               D   alternator

          1.3.3      A device that changes direct           E   solar panels
                     current to alternating current
                                                            F   mechanisation
          1.3.4      A device used to store energy
                     generated by a wind turbine            G   compressor

          1.3.5      Makes it possible for spares to        H   battery
                     be purchased from any agent
                     instead of a specific one              I   anemometer
                                                                                         (5 x 2)       (10)

                                                                           TOTAL SECTION A:            40

Copyright reserved                                                                  Please turn over

### Page 6

Agricultural Technology                         6                             DBE/November 2024
                                          NSC Confidential

SECTION B

QUESTION 2: MATERIALS AND STRUCTURES

Start this question on a NEW page.

2.1       Various alloy elements have a positive influence on stainless steel.

          Choose the influence on stainless steel (COLUMN B) that matches the alloy
          element (COLUMN A). Write only the letter (A–E) next to the question
          numbers (2.1.1 to 2.1.3) in the ANSWER BOOK, e.g. 2.1.4 F.

                    COLUMN A                                     COLUMN B
                 ALLOY ELEMENT                        INFLUENCE ON STAINLESS STEEL
          2.1.1 Manganese                             A   promotes the hardening of steel

          2.1.2 Nickel                                B      enhances magnetism

          2.1.3 Chromium                              C      decreases strengths

                                                      D      gives a fair amount of toughness
                                                             at low temperatures

                                                      E      gives steel a coarser structure
                                                                                         (3 x 1)      (3)

2.2       Complete the following table by choosing a word/phrase from the list below.
          Write only the word/phrase next to the question numbers (2.2.1 to 2.2.6) in
          the ANSWER BOOK. Each word/phrase may be used only ONCE.

                          hammer; soft; bronze; surface coating for food cans;
                                      copper; silver white metal

             NAME OF NON-
                                                PROPERTY                           USE
            FERROUS METAL
                 2.2.1                              2.2.2                       Electrical
                                                                               conductors
                     2.2.3            Does not generate a spark when              2.2.4
                                       struck against a hard surface
                      Tin                          2.2.5                           2.2.6
                                                                                                      (6)

2.3       State TWO important factors that should be considered when choosing an
          adhesive for a specific application.                                                        (2)

Copyright reserved                                                                 Please turn over

### Page 7

Agricultural Technology                            7                         DBE/November 2024
                                             NSC Confidential

2.4       The picture below shows a damaged fibreglass boat hull.

          2.4.1           Give a reason why fibreglass is used to repair damaged boat hulls.        (1)

          2.4.2           List THREE items needed for personal protection that must be
                          used when working with fibreglass.                                        (3)

          2.4.3           Name a cleaning agent that can be used to safely remove resin or
                          catalyst from your skin when working with fibreglass.                     (1)

2.5       Give ONE use of Vesconite for EACH of the applications by choosing a term
          from the list below. Write only the term next to the question numbers
          (2.5.1 to 2.5.4) in the ANSWER BOOK. Each term may be used only ONCE.

           centre-pivot bush; lifting arm bush; metal-to-metal bush; shackle pin bush

          2.5.1           Tractors                                                                  (1)

          2.5.2           Wind pump                                                                 (1)

          2.5.3           Tractor trailers                                                          (1)

          2.5.4           Irrigation equipment                                                      (1)

Copyright reserved                                                               Please turn over

### Page 8

Agricultural Technology                           8                             DBE/November 2024
                                            NSC Confidential

2.6       The pictures below show different types of electric farm fences.
                                 A                                        B

          2.6.1           Identify the type of electric fence shown in picture A and in
                          picture B.                                                                    (2)

          2.6.2           State an advantage of the electric fence in picture A.                        (1)

          2.6.3           Explain why barbed or razor wire should never be used in the
                          construction of an electric fence.                                            (2)

2.7       Complete the table below about specifications of electric fences. Write only
          the correct answer next to the question numbers (2.7.1 to 2.7.3) in the
          ANSWER BOOK.

                                                               CLEARANCE BETWEEN
                  PRESCRIBED VOLTAGE                            ELECTRIC FENCE AND
                                                               OVERHEAD POWER LINE

                                2.7.1                             3 metre clearance

             Between 1 000 and 33 000 volts                             2.7.2

                                2.7.3                             8 metre clearance
                                                                                                        (3)

2.8       Design a neatly labelled warning sign that should be placed on an electric
          fence to warn people of imminent danger. Include the required sign and
          measurements on the warning sign, as stipulated by the OHS Act.

          Use the following criteria:

           Measurements indicating the actual size of the sign                     2 marks
           Labelling/Inscription                                                   2 marks
           Correct drawing on the warning plate                                    1 mark               (5)

2.9       The energiser's earth system should be at least 5 metres away from the main
          supply unit. Do you agree with this statement? Motivate your answer.                          (2)
                                                                                                        [35]

Copyright reserved                                                                   Please turn over

### Page 9

Agricultural Technology                           9                          DBE/November 2024
                                            NSC Confidential

QUESTION 3: ENERGY

Start this question on a NEW page.

3.1       Name FOUR different renewable alternative energy sources that can be used
          on a farm to compensate for load-shedding.                                                    (4)

3.2       The picture below shows a wind turbine.

          3.2.1           Name a device that is installed on a wind turbine to direct the
                          turbine into the incoming wind.                                               (1)

          3.2.2           State THREE important requirements to consider before choosing
                          a wind turbine to generate electricity on a farm.                             (3)

          3.2.3           State TWO factors that might cause wind turbine failure.                      (2)

3.3       Tabulate TWO advantages and TWO disadvantages of solar energy.                                (4)

3.4       The picture below shows methanol.

                                                Methanol
                                                 CH3OH

          3.4.1           Name a fuel that methanol can easily be transformed into.                     (1)

          3.4.2           Name TWO natural sources available on a farm that can be used
                          to make methanol.                                                             (2)

3.5       Describe the manufacturing process of biodiesel.                                              (3)
                                                                                                        [20]

Copyright reserved                                                                   Please turn over

### Page 10

Agricultural Technology                          10                           DBE/November 2024
                                            NSC Confidential

QUESTION 4: SKILLS AND CONSTRUCTION PROCESSES

Start this question on a NEW page.

4.1       The picture below shows a MIG welding machine.

          4.1.1           What does EACH of the letters in the abbreviation MIG represent?           (3)

          4.1.2           Name parts A to D of the MIG welding machine in the picture
                          above.                                                                     (4)

          4.1.3           Explain the role that gas plays in the MIG welding process.                (2)

          4.1.4           Explain the purpose of spot welding.                                       (2)

4.2       Explain the effect that gravity has on the vertical up arc welding process and
          name TWO methods that can be used to control this effect.                                  (3)

4.3       What is the welding process called where worn parts of a grader blade are
          built up with a wear-resistant metal?                                                      (1)

4.4       Describe the process of preparing a broken cast-iron part before the welding
          process starts.                                                                            (5)

4.5       State TWO types of wear that metals can be subjected to.                                   (2)

Copyright reserved                                                                Please turn over

### Page 11

Agricultural Technology                          11                     DBE/November 2024
                                            NSC Confidential

4.6       State the effect of EACH of the following actions when cutting with the
          oxyacetylene cutting apparatus:

          4.6.1           Moving the cutting torch too fast                                    (1)

          4.6.2           Moving the cutting torch too slow                                    (1)

4.7       The picture below shows a plasma-cutting machine.

          4.7.1           State TWO factors that must be considered before buying a
                          plasma-cutting machine.                                              (2)

          4.7.2           Name TWO gases that can be used in the plasma-cutting process
                          to remove the molten metal.                                          (2)

          4.7.3           Explain the plasma-cutting process.                                  (4)

          4.7.4           State THREE safety measures that must be kept in mind when
                          working with a plasma-cutting machine.                               (3)
                                                                                               [35]

Copyright reserved                                                          Please turn over

### Page 12

Agricultural Technology                         12                             DBE/November 2024
                                           NSC Confidential

QUESTION 5: TOOLS, IMPLEMENTS AND EQUIPMENT

Start this question on a NEW page.

5.1       The picture below shows a baling machine that is used to make round bales.

          5.1.1           Name the type of bale-forming system that is used in the picture
                          above.                                                                      (1)

          5.1.2           Describe the bale-forming process inside the baling chamber of
                          this type of baling machine.                                                (5)

          5.1.3           Name THREE tasks that should be performed when doing
                          maintenance on this type of baling machine.                                 (3)

          5.1.4           Round bales have the potential to roll down a hill. Explain TWO
                          safety precautions that must be kept in mind when ejecting round
                          bales against a slope.                                                      (2)

5.2       Complete the table below by comparing the friction clutch to the hydraulic
          clutch. Write only the correct answer next to the question numbers
          (5.2.1 to 5.2.4) in the ANSWER BOOK.

                                          FRICTION CLUTCH        HYDRAULIC CLUTCH
              APPLICATION                       5.2.1                  5.2.3
              LOAD CAPACITY                     5.2.2                  5.2.4                          (4)

5.3       Give FOUR examples of irresponsible human behaviour that can cause
          tractor rollovers.                                                                          (4)

5.4       Explain the consequences of the following installation errors:

          5.4.1           The mass of moving parts is not spread equally over the bearings
                          of a hammer mill                                                            (2)

          5.4.2           The cyclone of the hammer mill does not hang level                          (2)

Copyright reserved                                                                 Please turn over

### Page 13

Agricultural Technology                           13                           DBE/November 2024
                                             NSC Confidential

5.5       Name the type of hydraulic cylinder that is installed in the power steering
          system of a tractor. Motivate your answer.                                                   (2)

5.6       The diagram below shows a V-belt pulley system.

                                                                  C
                                              B
                                       A

          5.6.1           Name a device that must be installed between parts A and B to
                          enable them to turn as a unit.                                               (1)

          5.6.2           Calculate the speed ratio of the pulley system, if pulley B rotates at
                          a speed of 1 200 r/min and pulley C at a speed of 600 r/min. Show
                          ALL calculations.                                                            (4)

          5.6.3           State THREE disadvantages of V-belts.                                        (3)

5.7       The picture below shows a gearbox installed on a centre-pivot irrigation
          system.

          5.7.1           Identify the types of gears labelled A and B.                                (2)

          5.7.2           State TWO functions of this type of gear assembly.                           (2)

          5.7.3           Indicate which substance is used inside this gearbox to reduce
                          wear and friction.                                                           (1)

5.8       State TWO advantages of mechanisation in modern agriculture.                                 (2)
                                                                                                       [40]

Copyright reserved                                                                  Please turn over

### Page 14

Agricultural Technology                           14                                 DBE/November 2024
                                             NSC Confidential

QUESTION 6: WATER MANAGEMENT

Start this question on a NEW page.

6.1       Study the pictures of two different irrigation systems below and answer the
          questions that follow.

                                  A                                              B

          6.1.1           Identify the type of irrigation system in picture A.                              (1)

          6.1.2           Name a type of filter system that can be installed in an irrigation
                          system to prevent blockage of the sprayer nozzles.                                (1)

          6.1.3           Give THREE reasons why a farmer would prefer irrigation
                          system A instead of irrigation system B.                                          (3)

          6.1.4           Explain the function of the down pipes connected to the
                          goosenecks on irrigation system B.                                                (2)

6.2       State TWO advantages of an irrigation timer that is installed in an irrigation
          system.                                                                                           (2)

6.3       Explain the design of a septic tank as used in a household sewage system.                         (5)

6.4       Design a distribution field used to evenly distribute the wastewater from a
          septic tank to the absorption field.

          The drawing must include the following:

                                      Distribution box            1 mark
                                      Measurements                1 mark
                                      Labels                      1 mark
                                      Direction of flow           1 mark
                                      Pipe system                 1 mark                                    (5)

Copyright reserved                                                                       Please turn over

### Page 15

Agricultural Technology                          15                          DBE/November 2024
                                            NSC Confidential

6.5       A farmworker uses a water pump to fill a water tank. The water tank has a
          capacity of 10 000 litres. It takes 1 hour 20 minutes to fill the tank.

          Use the following formula to calculate the flow rate of the water through the
          system.

          Formula: Flow rate = Content
                                Time                                                             (3)

6.6       The pictures below show various components found in an irrigation system.

                                  A                                      B

                                  C                                      D

          6.6.1           Name TWO different systems that can be used to connect the
                          motor in picture A to the centrifugal pump in picture B.               (2)

          6.6.2           Picture C shows a dripper that is used in a drip irrigation system.
                          Name FOUR disadvantages of this type of irrigation system.             (4)

          6.6.3           Picture D shows an inline water filter that uses a sieve to filter
                          impurities from the water. Name TWO other water filtration
                          methods that can be used to filter irrigation water.                   (2)
                                                                                                 [30]

                                                                       TOTAL SECTION B:          160
                                                                          GRAND TOTAL:           200

Copyright reserved

## Related documents

- [Agricultural Technology Nov 2024 MG Eng](https://www.hlayiso.com/library/agricultural-technology-nov-2024-mg-eng/5735a5ce-d167-4c13-bf13-9b5b710aed67) — Agricultural Technology · Memo · 2024 · Eng
- [Agricultural Technology Nov 2024 MG Afr](https://www.hlayiso.com/library/agricultural-technology-nov-2024-mg-afr/fce88f27-4539-47d4-b4b5-d7ddad4cd2a6) — Agricultural Technology · Memo · 2024 · Afr
- [Agricultural Technology May-June 2024 MG Afr](https://www.hlayiso.com/library/grade-12-agricultural-technology-2024-nsc-june-exam-memorandum-afrikaans/3365189d-e03a-49db-801a-0b473132a0f4) — Agricultural Technology · Memo · 2024 · Afr
- [Agricultural Technology May-June 2024 MG Eng](https://www.hlayiso.com/library/grade-12-agricultural-technology-2024-nsc-june-exam-memorandum-english/57faf85a-afb6-414c-bf66-0e0ede28ff4b) — Agricultural Technology · Memo · 2024 · Eng
- [Agricultural Technology May-June 2023 Eng](https://www.hlayiso.com/library/agricultural-technology-may-june-2023-eng/6e72892b-deb8-4820-8758-b91c5592448a) — Agricultural Technology · QP · 2023 · Eng
- [Agricultural Technology May-June 2023 Afr](https://www.hlayiso.com/library/agricultural-technology-may-june-2023-afr/0a79565a-1cf4-4b59-bd47-7c7ae750b4f3) — Agricultural Technology · QP · 2023 · Afr

## More from Grade 12 Agricultural Technology

- [Gr 12 Agric Tech ATP 2023-24](https://www.hlayiso.com/library/gr-12-agric-tech-atp-2023-24/9d982b07-0af2-4c43-8efe-886b4631bf17) — ATP
- [Agricultural Technology May-June 2025 MG Afr](https://www.hlayiso.com/library/agricultural-technology-may-june-2025-mg-afr/5f3f1dd7-8ba2-41ba-97bd-f8a4f9dfbdd5) — Memo · 2025 · Afr
- [Agricultural Technology Nov 2025 MG Eng](https://www.hlayiso.com/library/grade-12-agricultural-technology-2025-nsc-november-exam-memorandum/69e68c35-b84c-4320-b0d8-58fcb6116f22) — Memo · 2025 · Eng
- [Agricultural Technology Nov 2025 MG Afr](https://www.hlayiso.com/library/grade-12-agricultural-technology-2025-nsc-november-exam-memorandum/84499f01-76f1-43ac-8b53-d844857b9e13) — Memo · 2025 · Afr
- [Agricultural Technology May-June 2023 MG Afr](https://www.hlayiso.com/library/agricultural-technology-may-june-2023-mg-afr/49b9303d-33e4-4f5e-adbe-90dbadf7c5b7) — Memo · 2023 · Afr
- [Agricultural Technology May-June 2023 MG Eng](https://www.hlayiso.com/library/agricultural-technology-may-june-2023-mg-eng/db10383d-7cc4-41f6-9140-68d351a16776) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
