# Civil Technology Grade 12 Eastern Cape Mock 2022 QP (Eng)

> Grade 12 Civil Technology question paper from the Eastern Cape Mock Exam 2022 (English), 17 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-civil-services-english/90720b3f-011a-43dc-8be9-862cb2bbc268
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2022
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 17

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 Eastern Cape Mock 2022 QP (Eng)](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-civil-services-english/90720b3f-011a-43dc-8be9-862cb2bbc268)

## About this document

Civil Technology · Grade 12 · Eastern Cape Mock Exam · 2022 · English. Question paper, 17 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                             NATIONAL
                        SENIOR CERTIFICATE

                                 GRADE 12

                         SEPTEMBER 2022

         CIVIL TECHNOLOGY: CIVIL SERVICES

MARKS:   200

TIME:    3 hours

         This question paper consists of 17 pages, including 2 answer sheets.

### Page 2

Downloaded from hlayiso.com
2                        CIVIL TECHNOLOGY: CIVIL SERVICES                  (EC/SEPTEMBER 2022)

 REQUIREMENTS:

 1.    Drawing instruments

 2.    A non-programmable pocket calculator

 3.    ANSWER BOOK

 INSTRUCTIONS AND INFORMATION

 1.    This question paper consists of SIX questions: TWO questions are generic and
       FOUR questions are subject specific.

 2.    Answer ALL the questions.

 3.    Answer each question as a whole. Do NOT separate subsections of questions.

 4.    Start the answer to EACH question on a NEW page.

 5.    Do NOT write in the margins of the ANSWER BOOK.

 6.    You may use sketches to illustrate your answers.

 7.    Write ALL calculations and answers in the ANSWER BOOK or on the attached
       ANSWER SHEETS.

 8.    Use the mark allocation as a guide to the length of your answers.

 9.    Make drawings and sketches in pencil, fully dimensioned and neatly finished
       off with descriptive titles and notes to conform to the SANS/SABS Code of
       Practice for Building Drawings.

 10. For the purpose of this question paper, the size of a brick should be taken as
     220 mm x 110 mm x 75 mm.

 11. Use your own discretion where dimensions and/or details have been omitted.

 12. Answer QUESTIONS 2.1 and 6.1 on the attached ANSWER SHEETS using
     drawing instruments where necessary.

 13. Write your NAME on every ANSWER SHEET and hand them in with your
     ANSWER BOOK, whether you have answered the question or not.

 14. Owing to electronic transfer, drawings in the question paper are NOT to scale.

 15. Google Images was used as the source of all photographs and pictures.

 16. Write neatly and legibly.

Copyright reserved                                                            Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)                CIVIL TECHNOLOGY: CIVIL SERVICES                              3

QUESTION 1: SAFETY AND MATERIALS (GENERIC)

Start this question on a NEW page.

1.1    Define the term accident.                                                              (2)

1.2    Name the material that scaffolding is made from.                                       (1)

1.3    Choose the correct answer from the words given in brackets that is related to
       scaffolding:

       1.3.1   The safety factor that is used for scaffolding frames is (one / two /
               three).                                                                        (1)

       1.3.2   The minimum thickness of a wooden scaffold platform is (38 mm /
               50 mm / 76 mm).                                                                (1)

       1.3.3   The minimum height of a suspended scaffold is (900 mm / 1 200 mm
               / 1 500 mm).                                                                   (1)

1.4    Give TWO reasons why scaffolding must be inspected before it can be used.
                                                                          (2 x 1)             (2)

1.5    What is the maximum distance that a suspended scaffold may hang over the
       edge of the structure?                                                                 (1)

1.6    What is the maximum height of a trestle scaffold?                                      (1)

1.7    Answer the following questions with regard to ladders.

       1.7.1   Why should only one person at a time use a ladder?                              (1)

       1.7.2   What should the end of a ladder be marked with for visibility when it
               is transported?                                                                 (1)

       1.7.3   Name any ONE material that ladders can be made from.                            (1)

       1.7.4   Why should ladders be kept clean and free from oil and grease?                  (1)

1.8    Name TWO advantages of a water-based paint.                               (2 x 1)       (2)

1.9    Name TWO advantages of the curing of concrete.                            (2 x 1)       (2)

1.10   Name TWO methods that can be used to prevent the corrosion of metals.
                                                                         (2 x 1)               (2)
                                                                                              [20]

Copyright reserved                                                         Please turn over

### Page 4

Downloaded from hlayiso.com
 4                         CIVIL TECHNOLOGY: CIVIL SERVICES                 (EC/SEPTEMBER 2022)

QUESTION 2: GRAPHICS, JOINING AND EQUIPMENT (GENERIC)

2.1    FIGURE 2.1 on ANSWER SHEET A shows the outer lines of a structure which
       must be built on a site. Draw the site plan on scale 1 : 200 on ANSWER
       SHEET A so that the structure is in the middle of the site.

       The site plan must comply with the following requirements.
       Use the points table on SHEET A as reference.

       2.1.1    Site size is 30 m wide from east to west and 40 m long from south to
                north.                                                                      (2)

       2.1.2    Pavement of 2 m and the street of 6 m on the south side.                    (3)

       2.1.3    Building boundaries are 2 m on the east, north and west sides and 4 m
                on the south side.                                                          (4)

       2.1.4    3 m wide entrance to the site.                                              (2)

       2.1.5    Datum level in the north-west corner of the site.                           (2)

      Draw in the sewer lay-out for the structure and show the following:

       2.1.6    Water closet symbol at the abbreviation                                     (1)

       2.1.7    Sewer pipes connections                                                     (2)

       2.1.8    Rodding eye with the abbreviation                                           (2)

       2.1.9    Inspection eye with the abbreviation                                        (2)

       2.1.10 Manhole with the abbreviation                                                 (2)

       Indicate the following measurements:

       2.1.11 Length and width of the site                                                  (4)

       2.1.12 South and west building boundaries                                            (2)

2.2    What is the advantage of the square shoulder bolt?                                   (1)

2.3    Name parts A to D of the bolt in FIGURE 2.3.

                A

               B                        C         D

                                      FIGURE 2.3                               (4 x 1)      (4)

 Copyright reserved                                                            Please turn over

### Page 5

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2022)               CIVIL TECHNOLOGY: CIVIL SERVICES                         5

2.4    What is the purpose of the nylon insert of a hexagonal nut?                         (1)

2.5    What is the advantage of a wing nut?                                                (1)

2.6    FIGURE 2.6 shows the dumpy level reading which is taken on the telescopic
       staff. Answer the following questions with regard to the reading.

                                    1.7

                                    1.6

                                          FIGURE 2.6

       2.6.1    What is the height reading on the staff?                                   (1)

       2.6.2    Determine the distance between the dumpy level and the staff.
                Show ALL calculations, formulae and units.                                 (4)
                                                                                          [40]

                                                                 TOTAL SECTION A:          60

 Copyright reserved                                                    Please turn over

### Page 6

Downloaded from hlayiso.com
6                          CIVIL TECHNOLOGY: CIVIL SERVICES                (EC/SEPTEMBER 2022)

QUESTION 3: SAFETY, MATERIAL AND CONSTRUCTION (SPECIFIC)
Start the question on a NEW page.
3.1 Indicate if the following statements are TRUE or FALSE. Write only ‘true’ or
    ‘false’ next to the question number in the ANSWER BOOK.
      3.1.1    A mouth-nose mask provides sufficient protection when working in
               manholes with dangerous gasses.                                             (1)

      3.1.2    An extractor fan can be used to displace dangerous gasses in a
               manhole.                                                                    (1)

      3.1.3    Open manholes must be cordoned off before it is entered.                    (1)
      3.1.4    The person entering a manhole must have medical training.                   (1)
3.2 Describe the purpose of safety nets above door openings of a structure which
    are repaired.                                                                          (2)
3.3 Describe TWO responsibilities of the contractor when working in high places.
                                                                           (2 x 2)         (4)

3.4 Fully motivate why zinc is seen as a highly reactive metal.                            (4)

3.5 Complete the following descriptions of the factors that determine galvanic
    corrosion through thermodynamic and kinetic conditions.
      •   The difference between the …3.5.1 … potential of the two metals.                 (1)
      •   Contact resistance at the …3.5.2 … between the two metals.                       (1)
      •   Electrical resistance of the …3.5.3 ... solution.                                (1)
      •   The presence of a …3.5.4 … film.                                                 (1)
3.6 Answer the following questions with regard to the structure in FIGURE 3.6.

              A
                                                                       B

                                          FIGURE 3.6
      3.6.1    What is this structure called?                                              (1)
      3.6.2    Name parts A and B.                                             (2 x 1)     (2)
      3.6.3    Briefly motivate why part A is built with an incline.                       (2)
Copyright reserved                                                            Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)               CIVIL TECHNOLOGY: CIVIL SERVICES                         7

3.7 A drain line for a 100 mm drain pipe must be laid for a house. A gradient of
    1 : 40 over a distance of 20 m is specified.
    Determine the height of the pitch at the end. Show ALL calculations.                  (3)

3.8 FIGURE 3.8 shows the shoring for a trench. Answer the following questions
    with regard to the shoring.

               A
               B
               C

                                        FIGURE 3.8

      3.8.1    In which type of ground will this shoring be used?                         (1)

      3.8.2    Name parts A to C of the shoring.                              (3 x 1)     (3)
                                                                                         [30]

Copyright reserved                                                    Please turn over

### Page 8

Downloaded from hlayiso.com
8                         CIVIL TECHNOLOGY: CIVIL SERVICES               (EC/SEPTEMBER 2022)

QUESTION 4: COLD WATER SUPPLY, WARM WATER SUPPLY AND TOOLS
            (SPECIFIC)

4.1   Answer the following questions with regard to the water supply system in
      FIGURE 4.1.

                                                                BOUNDARY
           KERB                                                 WALL

                                    B                           E

                                    C                   D
          A

                                           FIGURE 4.1

      4.1.1    Name components A to D.                                     (4 x 1)         (4)

      4.1.2    What is the minimum dimension at E?                                         (1)

      4.1.3    Who is responsible for the installation of component B?                     (1)

4.2   Answer the following questions with regard to the valve in FIGURE 4.2.

                                                            C
                                                            B

                                                            A

                                           FIGURE 4.2

      4.2.1    Name the valve in FIGURE 4.2.                                               (1)

      4.2.2    Name the parts A to C.                                       (3 x 1)        (3)

      4.2.3    Where will this type of valve be used?                                      (1)

Copyright reserved                                                             Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)                CIVIL TECHNOLOGY: CIVIL SERVICES                          9

4.3   Answer the following questions with regard to the soil water fitting in
      FIGURE 4.3.

                                                            A
                                                            A

                                            FIGURE 4.3

      4.3.1    What is the sectional size of this pipe?                                      (1)

      4.3.2    What is the fitting in FIGURE 4.3 called?                                     (1)

      4.3.3    What is the purpose of part A?                                                (1)

4.4   Briefly motivate why gaskets are used in the flange joints of cast iron pipes.         (2)

4.5   What is the purpose of a low-flow shower head?                                         (1)

4.6   Explain the operation and advantages of a red water diverter.                          (6)

4.7   Identify the following symbols and abbreviations for hot water systems.

      4.7.1            H                                                                     (1)

      4.7.2
                        A
                                                                                             (1)

      4.7.3             C

                        H                                                                    (1)

      4.7.4    PCV                                                                           (1)

      4.7.5    V                                                                             (1)

Copyright reserved                                                        Please turn over

### Page 10

Downloaded from hlayiso.com
10                        CIVIL TECHNOLOGY: CIVIL SERVICES                     (EC/SEPTEMBER 2022)

4.8   Indicate the water flow direction of the water in the pipes 4.8.1 to 4.8.5 of the
      hot water system in FIGURE 4.8.
      Write the correct arrow letter against the number for example 4.8.6 – B.

                                           4.8.4                               4.8.5
                             4.8.3         A B                                 A B
                             A B

                                                                                       Hot water supply
         4.8.1                                       4.8.2
         A B                                         A B
       Service pipe                             Cold water supply

                                        FIGURE 4.8                                (5 x 1)                  (5)

4.9   Indicate if the following statements are TRUE or FALSE. Write only ‘true’ or
      ‘false’ next to the question numbers (4.9.1 to 4.9.3) in the ANSWER BOOK.

      4.9.1    The safety tray of a geyser prevents the pressure in a geyser getting
               too high.                                                                                   (1)

      4.9.2    A low-pressure solar geyser is installed lower than the taps.                               (1)

      4.9.3    A non-return valve is installed at high pressure solar geysers.                             (1)

4.10 Name FOUR caring measures for the compressed-air test apparatus.              (4 x 1)                 (4)
                                                                                                          [40]

Copyright reserved                                                                Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)                CIVIL TECHNOLOGY: CIVIL SERVICES                          11

QUESTION 5: DRAINAGE AND QUANTITIES (SPECIFIC)

5.1   Answer the following questions with regard to the drainage fitment in
      FIGURE 5.1.

                                         FIGURE 5.1

      5.1.1    What is this fitment called?                                                  (1)

      5.1.2    Describe the functioning AND purpose of this fitment when waste
               water is released into a drainage system.                                     (4)

5.2   Answer the following questions with regard to the drainage fixture in
      FIGURE 5.2.

                                         FIGURE 5.2

      5.2.1    What is this drainage fixture in FIGURE 5.2 called?                           (1)

      5.2.2    Where is this fixture installed?                                              (1)

      5.2.3    Name TWO disadvantages of this fixture.                            (2 x 1)    (2)

      5.2.4    Briefly describe the purpose of the water at the bottom of the fixture.       (2)

Copyright reserved                                                        Please turn over

### Page 12

Downloaded from hlayiso.com
12                         CIVIL TECHNOLOGY: CIVIL SERVICES                 (EC/SEPTEMBER 2022)

5.3 Answer the following questions with regard to the drainage structure in
    FIGURE 5.3.

       A                                                        LIQUID LEVEL
                                                                              C

        B

                                        FIGURE 5.3

      5.3.1     What is the structure called?                                                  (1)

      5.3.2     Briefly describe how the organic matter decomposes in the structure.           (2)

      5.3.3     What is the purpose if the inlet pipe opening at A?                            (1)

      5.3.4     Briefly motivate why the inflow at B must be lower than the liquid
                level.                                                                         (2)

      5.3.5     To which structure is the effluent at C discharged?                            (1)

5.4   Make neat sketches to illustrate the following drainage symbols:

      5.4.1    Sink                                                                            (2)

      5.4.2    Bidet                                                                           (2)

5.5   Choose the correct answer from those in brackets for the sewer treatment
      process and write only the question numbers (5.5.1 to 5.5.2) in your ANSWER
      BOOK with the correct answer.

      5.5.1    The waste-water goes through (stormwater channels / underground
               sewerage pipes) to the treatment plant.                                         (1)

      5.5.2    The separation process filters out (bigger solids / garden waste).              (1)

Copyright reserved                                                                Please turn over

### Page 13

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2022)                 CIVIL TECHNOLOGY: CIVIL SERVICES                       13

5.6    FIGURE 5.6 shows the front elevation of the cold-water supply from the water
       meter to a house on scale 1 mm = 100 mm. The main cold-water pipe has a
       diameter of 22 mm and the branch pipes have a diameter of 15 mm. Study the
       drawing and determine the material needed for the plumbing installation by
       completing the table.

                                                   C

                                         FIGURE 5.6

         WATER SUPPLY
                           MATERIAL               SIZE           QUANTITY    LENGTH
          APPLIANCES
       Cold-water pipe       5.6.1               22 mm                1        5.6.2
       Cold-water pipe       5.6.3               15 mm                1        5.6.4
       Reducing elbow                        22 mm x 15 mm          5.6.6
                             5.6.5
       90°
       Elbow 90°             5.6.7              15 mm               5.6.8
       Reducing tee          5.6.9      22 mm x 22 mm x 15 mm      5.6.10
       Tee                  5.6.11          15 mm x 15 mm          5.6.12                  (12)

5.7    A cylindrical water tank is 2 400 mm high and has a diameter of 2 100 mm.
       Calculate the volume of the tank.
       Show ALL calculations, formulae and units.                                           (4)
                                                                                           [40]

 Copyright reserved                                                     Please turn over

### Page 14

Downloaded from hlayiso.com
14                         CIVIL TECHNOLOGY: CIVIL SERVICES                  (EC/SEPTEMBER 2022)

QUESTION 6: GRAPHIC COMMUNICATION, ROOF WORK, STORMWATER
            AND JOINING (SPECIFIC)

6.1 FIGURE 6.1 on ANSWER SHEET C shows the top and front elevation of a
    cone. Draw the development of the cone according to the radial-line method
    on ANSWER SHEET C. Add an allowance for the seam.
    Show ALL construction lines.                                                              (14)

6.2 Choose a description with regard to a high-pressure geyser from COLUMN A
    that matches the correct item in COLUMN B.
    Write only the correct letter (A–H) next to the question numbers (6.2.1 to 6.2.5)
    in the ANSWER BOOK, for example 6.2.6 I.

                   COLUMN A                                    COLOMN B
       6.2.1    Main function of gutters        A   Brackets

       6.2.2    Gutters are fixed to it         B   Offset

       6.2.3    Bottom end of the downpipe      C   Outlet

       6.2.4    Gutters are supported with it   D   To channel water off the roof

       6.2.5    Connection between the          E   To channel soil water of the roof
                gutter and downpipe

                                                F   Facia board

                                                G Rain water shoe

                                                H   Roof covering
                                                                                    (5 x 1)    (5)

6.3 Explain where flashings are installed.                                                      (2)

6.4 What is the purpose of surface channels?                                                    (1)

6.5 Name THREE negative consequences of poor stormwater constructions.
                                                                      (3 x 1)                   (3)

6.6 What is the purpose of the grill on top of stormwater openings?                             (1)

6.7 Indicate if the following statements are TRUE or FALSE. Write only ‘true’ or
    ‘false’ next to the question number in the ANSWER BOOK.

      6.7.1    The teeth of a hacksaw are facing forward.                                       (1)

      6.7.2    The burr of a cut pipe must be removed with a hacksaw.                           (1)

Copyright reserved                                                              Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)                CIVIL TECHNOLOGY: CIVIL SERVICES                      15

6.8 Answer the following questions with regard to the joint in FIGURE 6.8.

                                                              A

                                            FIGURE 6.8

      6.8.1    What is this joint called?                                                 (1)

      6.8.2    What is part A called?                                                     (1)
                                                                                         [30]

                                                                             TOTAL:      200

Copyright reserved                                                    Please turn over

### Page 16

Downloaded from hlayiso.com
16                         CIVIL TECHNOLOGY: CIVIL SERVICES            (EC/SEPTEMBER 2022)

                              CIVIL TECHNOLOGY        NAME:
 ANSWER SHEET          A           GENERIC

2.1 FIGURE 2.1 on ANSWER SHEET A shows the outer lines of a structure which
    must be built on a site. Draw the site plan on scale 1 : 200 on
    ANSWER SHEET A so that the structure is in the middle of the site.                (28)

                              WC

                                                              Plot size           2
                                                              Pavement + street   3
                                                              Building boundaries 4
                                                              Entrance            2
                                                              Datum level         2
                                                              Water closet        1
                                                              Sewer connections   2
                                                              Inspection eye      2
                                                              Rodding eye         2
                                                              Manhole             2
                                                              Measurements        6
                                                                          TOTAL 28

Copyright reserved                                                        Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)             CIVIL TECHNOLOGY: CIVIL SERVICES                        17

                             CIVIL TECHNOLOGY       NAME:
 ANSHER SHEET           B      CIVIL SERVICES

6.1    FIGURE 6.1 on ANSWER SHEET B shows the top and front elevation of a
       cone.
       Draw the development of the cone according to the radial-line method on
       ANSWER SHEET B. Add an allowance for the seam. Show ALL construction
       lines.                                                                  (14)

                       FRONT ELEVATION

                                           Dividing lines 0-6 on top view          4
                                           Halve circle B-C                        2
                                           Seam lines A–B and A–C                  2
                                           Construction lines A0–A12               6
                       TOP ELEVATION                                        TOTAL 14

Copyright reserved                                                   Please turn over

## Related documents

- [CIV TECH GR12 QP SEPT2022 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-woodworking-english/c3b4a7c0-761a-45aa-a578-9b98afc86830) — Civil Technology · QP · 2022 · Eng
- [CIV TECH GR12 MEMO SEPT2022 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2022-woodworking-english/62d9cbb1-1077-4edb-86c4-7a21fd6749a9) — Civil Technology · Memo · 2022 · Eng
- [CIV TECH GR12 MEMO SEPT2022 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2022-civil-services-english/896ddb1f-2144-4bfc-a35a-3a71507d7637) — Civil Technology · Memo · 2022 · Eng
- [CIV TECH GR12 QP SEPT2021 English Construction](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2021-english-construction/551ab3e9-47c5-4ab0-a0cf-bc66dda5a956) — Civil Technology · QP · 2021 · Eng
- [CIVIL TECH QP GR12 SEPT 2019 Woodwork English](https://www.hlayiso.com/library/civil-tech-qp-gr12-sept-2019-woodwork-english/7eaa0222-4bca-4690-a584-eab0441f77d9) — Civil Technology · QP · 2019 · Eng
- [CIV TECH GR12 MEMO SEPT2023 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2023-construction-english/9ab6f3f0-4774-49bf-8311-57f09822adf6) — Civil Technology · Memo · 2023 · Eng

## More from Grade 12 Civil Technology

- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Memo · 2024 · Eng
- [Civil Technology Nov 2022 (Civil Services) MG Afr](https://www.hlayiso.com/library/civil-technology-nov-2022-civil-services-mg-afr/42b5315c-825c-40e3-b394-85e0253fc0fb) — Memo · 2023 · Afr
- [Civil Technology Nov 2023 (Construction) Eng](https://www.hlayiso.com/library/civil-technology-nov-2023-construction-eng/e6743728-8140-42ae-838d-282654a975a5) — QP · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
