# Civil Technology Grade 12 Eastern Cape Mock 2019 QP (Eng)

> Grade 12 Civil Technology question paper from the Eastern Cape Mock Exam 2019 (English), 24 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/civil-tech-qp-gr12-sept-2019-woodwork-english/7eaa0222-4bca-4690-a584-eab0441f77d9
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2019
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 24

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 Eastern Cape Mock 2019 QP (Eng)](https://www.hlayiso.com/library/civil-tech-qp-gr12-sept-2019-woodwork-english/7eaa0222-4bca-4690-a584-eab0441f77d9)

## About this document

Civil Technology · Grade 12 · Eastern Cape Mock Exam · 2019 · English. Question paper, 24 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                             NATIONAL
                        SENIOR CERTIFICATE

                              GRADE 12

                         SEPTEMBER 2019

         CIVIL TECHNOLOGY: WOODWORKING

MARKS:   200

TIME:    3 hours

                                 *Cvlte3*

         This question paper consists of 19 pages, including 3 answer sheets.

### Page 2

Downloaded from hlayiso.com
2                        CIVIL TECHNOLOGY: WOODWORKING                      (EC/SEPTEMBER 2019)

REQUIREMENTS:

1.      ANSWER BOOK

2.      Drawing instruments

3.      A non-programmable pocket calculator

INSTRUCTIONS AND INFORMATION

1.      This question paper consists of SIX questions: TWO questions are generic and
        FOUR questions are subject specific.

2.      Answer ALL the questions.

3.      Answer each question as a whole. Do NOT separate subsections of questions.

4.      Start the answer to EACH question on a NEW page.

5.      Do NOT write in the margins of the ANSWER BOOK.

6.      You may use sketches to illustrate your answers.

7.      Write ALL calculations and answers in the ANSWER BOOK or on the attached
        ANSWER SHEETS.

8.      Use the mark allocation as a guide to the length of your answers.

9.      Make drawings and sketches in pencil, fully dimensioned and neatly finished off with
        descriptive titles and notes to conform to the SANS/SABS Code of Practice for
        Building Drawings.

10.     For the purpose of this question paper, the size of a brick should be taken as
        220 mm x 110 mm x 75 mm.

11.     Use your own discretion where dimensions and/or details have been omitted.

12.     Answer QUESTIONS 2.2, 4.5 and 6.5 on the attached ANSWER SHEETS using
        drawing instruments where necessary.

13.     Write your NAME on every ANSWER SHEET and hand them in with your ANSWER
        BOOK, whether you have answered the question or not.

14.     Due to electronic transfer, drawings in the question paper are NOT to scale.

Copyright reserved                                                             Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                CIVIL TECHNOLOGY: WOODWORKING                               3

  QUESTION 1: SAFETY OHSA AND MATERIALS (GENERIC)

  Start this question on a NEW page.

  1.1 What is the maximum height of a trestle scaffold?                                        (1)

  1.2 Building rubble should never be dropped from elevated areas. Name the
      correct method of disposing rubble from elevated areas.                                  (2)

  1.3 Briefly motivate why a construction site must be suitably cordoned off.                  (2)

  1.4 Choose the correct answer from those in brackets with regards to the
      construction process of stairs:

        1.4.1    Stairways must be installed at least (30° / 25°) from the horizontal
                 platform and not more then (45° / 50°) from a wall.                           (2)

        1.4.2    Stairways that will not be a permanent part of the building construction
                 must have landings of at least (760 x 560 mm / 750 x 600 mm) for
                 every (3,7 m / 2,5 m) or less vertical rise.                                  (2)

  1.5 FIGURE 1.5 shows a ladder that is placed against a wall. What is the correct
      measurement at 1.5.A to keep it stable? Show or indicate how to achieve the
      ratio.

                                                             2m

                                                A

                                           FIGURE 1.5                                          (2)

  1.6 Explain the safety requirements when extending a ladder.                                 (2)

  1.7 Briefly explain the electroplating process of metals.                                    (2)

  1.8 Name THREE advantages of electroplating metals.                               (3 x 1)    (3)

  1.9 Name TWO advantages of galvanising metals.                                    (2 x 1)     (2)
                                                                                               [20]

Copyright reserved                                                               Please turn over

### Page 4

Downloaded from hlayiso.com
4                         CIVIL TECHNOLOGY: WOODWORKING                    (EC/SEPTEMBER 2019)

 QUESTION 2:         GRAPHIC COMMUNICATING, JOINING AND EQUIPMENT
                     (GENERIC)

 Start this question on a NEW page.

 2.1 Indicate if the following statements, regarding site plans, are TRUE or FALSE.
     Write only ‘true’ or ‘false’ next to the question number in your ANSWER BOOK.

       2.1.1     Scale 1 : 10 is used                                                         (1)

       2.1.2     Ground contours are shown                                                    (1)

       2.1.3     Layout of sewage is shown                                                    (1)

       2.1.4     The proposed work is indicated in red                                        (1)

       2.1.5     Floor finishes of rooms are indicated                                        (1)

 2.2 FIGURE 2.2 on ANSWER SHEET A shows an incomplete floorplan of a flat to
     scale 1 : 100. Complete the floorplan by using the following information:

       2.2.1     Outside door at 2.2.A                                                        (2)

       2.2.2     Window at 2.2.B                                                              (2)

       2.2.3     Water closet at 2.2.C                                                        (2)

       2.2.4     Washbasin at 2.2.D                                                           (2)

       2.2.5     Wash tub at 2.2.E                                                            (2)

       2.2.6     One-way switch single pole at 2.2.F                                          (2)

       2.2.7     Fluorescent light at 2.2.G                                                   (2)

       2.2.8     Socket outlet at 2.2.H                                                       (2)

       2.2.9     Grease trap at 2.2.I                                                         (2)

       2.2.10    Wall-mounted light at 2.2.J                                                  (2)

 2.3 Identify the different types of bolts in FIGURES 2.3.1, 2.3.2 and 2.3.3.

               FIGURE 2.3.1               FIGURE 2.3.2             FIGURE 2.3.3                (3)

Copyright reserved                                                              Please turn over

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                CIVIL TECHNOLOGY: WOODWORKING                          5

 2.4 Answer the following questions on the tool in FIGURE 2.4.

                       A

                                                                            D
                       B

                       C

                                          FIGURE 2.4

       2.4.1     Identify the tool in FIGURE 2.4.                                          (1)

       2.4.2     Name ONE use of this tool.                                     (1 x 1)    (1)

       2.4.3     Name the different parts A–D.                                  (4 x 1)    (4)

       2.4.4     Name TWO uses of a laser level.                                           (2)

 2.5 Explain why the laser level should not be stored in extremely cold areas. Refer
     to the moisture inside the tool.                                                      (2)

 2.6 Explain the meaning of the following code for Rawl bolts: M08/25.                     (2)
                                                                                          [40]

                                                                 TOTAL SECTION A:              60

Copyright reserved                                                          Please turn over

### Page 6

Downloaded from hlayiso.com
6                          CIVIL TECHNOLOGY: WOODWORKING                       (EC/SEPTEMBER 2019)

 QUESTION 3:         CASEMENTS, CUPBOARDS, WALL-PANELLING AND
                     QUANTITIES (SPECIFIC)

 Start this question on a NEW page.

 3.1 Give ONE word/term for EACH of the following descriptions by choosing a
     word/term from the list below. Write only the word/term next to the question
     numbers (3.1.1–3.1.3) in the ANSWER BOOK, e.g. 3.1.4 fanlight

                              tilting batten; soffit; reveal; panel; rebate

       3.1.1    The area of the wall at the side of an opening that is at right angles to
                the general face of the wall around a door and window                                (1)

       3.1.2    A batten fixed to the eaves end of a pitched roof to maintain the roof
                slope at the eaves course                                                            (1)

       3.1.3    A groove or recess in woodwork to accommodate a panel or pane                        (1)

 3.2 FIGURE 3.2 below shows the sectional view of a tongue and groove wall panel
     from the floor to the ceiling, fastened to a 110 mm thick wall. Study the drawing
     and answer the questions that follow.

                                             FIGURE 3.2

       3.2.1    Identify parts A–E.                                                                  (5)

       3.2.2    What is the function of F?                                                           (2)

       3.2.3    Give TWO reasons for panelling a wall.                                               (2)

Copyright reserved                                                                Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                     CIVIL TECHNOLOGY: WOODWORKING                         7

 3.3 FIGURE 3.3 below shows the front and side elevation of a bedroom cupboard,
     without doors, fitted from floor to ceiling. An incomplete cutting list specifying
     some parts of the cupboard is given. Study the drawing and complete the cutting
     list by providing answers to 3.3.1–3.3.7.

                                              FIGURE 3.3

          Parts       Quantity   Unit     Length   Width   Thickness    Total    Material
                                                                       length
        Sides          3.3.1     mm       2 490    570        16       4 980       Oak
         Rail            1       mm       3.3.2    120        16        968        Oak
        Top of           1       mm        968     3.3.3      16        968        Oak
       top unit
       Bottom            1       mm       3.3.4    570        16        968        Oak
          unit
       Shelving          3       mm        570     492        16       3.3.5       Oak
         Kick            1       mm        968     3.3.6      16       968         Oak
         plate
         Back            1       mm       2 310    1100      3.3.7     2 310       Oak             (7)

Copyright reserved                                                              Please turn over

### Page 8

Downloaded from hlayiso.com
8                         CIVIL TECHNOLOGY: WOODWORKING                    (EC/SEPTEMBER 2019)

 3.4 FIGURE 3.4 below shows part of a double casement with fanlights. Study the
     picture and answer the questions that follow.

                                         FIGURE 3.4

       3.4.1    Name the THREE main parts of the double casement with fanlights.                (3)

       3.4.2    Discuss the purpose of a transom in a casement with fanlights.                  (3)

       3.4.3    Discuss the advantages of fanlights in a casement.                              (3)

       3.4.4    Define a casement window.                                                       (2)
                                                                                               [30]

Copyright reserved                                                               Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                   CIVIL TECHNOLOGY: WOODWORKING                    9

 QUESTION 4:          ROOFS, CEILINGS, TOOLS, EQUIPMENT AND MATERIALS
                      (SPECIFIC)

 Start this question on a NEW page.

 4.1 FIGURE 4.1 below shows a joint-to-joint member/part of a door. Study the
     drawing and answer the questions that follow.

                                           FIGURE 4.1

       4.1.1    Identify the joint construction.                                      (1)

       4.1.2    Identify parts A–D.                                                   (4)

Copyright reserved                                                       Please turn over

### Page 10

Downloaded from hlayiso.com
10                         CIVIL TECHNOLOGY: WOODWORKING                 (EC/SEPTEMBER 2019)

 4.2 FIGURE 4.2 below shows two woodworking machines. Study the pictures and
     answer the questions that follow.

                       A                                      B

                                        FIGURE 4.2

       4.2.1   Identify machines A and B.                                                 (2)

       4.2.2   Discuss how you will take care of machine B.                               (3)

       4.2.3   Recommend TWO ways of storing A after use.                                 (2)

 4.3 Give TWO properties of roof tiles.                                                   (2)

 4.4 Name the most common traditional type of profiled roofing that is used in
     South Africa.                                                                        (1)

Copyright reserved                                                          Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                CIVIL TECHNOLOGY: WOODWORKING                              11

 4.5 The migration of swallows from the north to the south in summer creates a big
     problem for home owners, because the birds build their nests in the eaves of
     roofs.
     A closed eave overhang can solve this problem. Draw therefore on ANSWER
     SHEET B, to a scale of 1 : 10, a detailed sectional view of a closed eave
     overhang of a roof truss.

       Show the following details in your drawing:

       •   Wall plate 114 mm x 38 mm
       •   Part of the 114 mm x 38 mm tie beam
       •   Part of the 114 mm x 38 mm rafter
       •   Roof pitch 30˚
       •   Beam filling
       •   Quarter round moulding 18 mm
       •   Purlins 76 mm x 50 mm
       •   Galvanised corrugated iron roof sheeting
       •   Covering material for the closing of the eaves (slats, soffit board, cement
           fibre board 6 mm)
       •   225 mm x 30 mm fascia board
       •   100 mm x 100 mm square gutter
       •   Downpipe 75 mm x 75 mm
       •   500 mm eaves overhang                                                              (22)

 4.6 Explain in your own words the difference between a hurricane clip and a gang
     nail (nail plate).                                                                        (1)

 4.7 Discuss the difference between the following:

       4.7.1     Hipped roof                                                                   (1)

       4.7.2     Hipped roof with a valley                                                     (1)
                                                                                              [40]

Copyright reserved                                                               Please turn over

### Page 12

Downloaded from hlayiso.com
12                           CIVIL TECHNOLOGY: WOODWORKING                          (EC/SEPTEMBER 2019)

 QUESTION 5:         CENTERING, FORMWORK, SHORING AND GRAPHICS AS
                     MEANS OF COMMUNICATION (SPECIFIC)

 Start this question on a NEW page.

 5.1 FIGURE 5.1 shows a sketch of a lock. Study the sketch and answer the
     questions that follow.

                                            FIGURE 5.1

       5.1.1    Identify the lock.                                                                   (1)

       5.1.2    Identify the part of the door into which the lock will be fitted.                    (1)

       5.1.3    Name an entrance door were this lock can be fitted.                                  (1)

       5.1.4    Name the part of the lock that will be fitted into the frame of the door.            (1)

       5.1.5    Explain the difference between a keyhole and a lock.                                 (2)

 5.2 Explain ONE use of the following shores:

       5.2.1    Double-flying shore                                                                  (1)

       5.2.2    Dead shore                                                                           (1)

 5.3 Describe the function of the following components of dead shore:

       5.3.1    Sole plate                                                                           (1)

       5.3.2    Prop/Strut                                                                           (1)

Copyright reserved                                                                     Please turn over

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                   CIVIL TECHNOLOGY: WOODWORKING                    13

 5.4 FIGURE 5.4 below shows a pictorial view of the construction detail underneath
     a centre of arch. Study the picture and answer the questions that follow.

                                           FIGURE 5.4

       5.4.1    Identify parts A–D.                                                     (4)

       5.4.2    Explain ONE use of A as shown in FIGURE 5.4.                            (1)

       5.4.3    Explain TWO purposes of part C.                                         (2)

       5.4.4    Describe the function of D.                                             (1)

 5.5 Recommend any THREE wooden board products that can be used as sides for
     formwork.                                                                          (3)

Copyright reserved                                                        Please turn over

### Page 14

Downloaded from hlayiso.com
14                       CIVIL TECHNOLOGY: WOODWORKING                   (EC/SEPTEMBER 2019)

 5.6 FIGURE 5.6 below shows a horizontal section of a square column.

       Study FIGURE 5.6 and identify parts A–F. Write only the answer next to the
       letters (A–F) in the ANSWER BOOK.

                                       FIGURE 5.6                                         (6)

 5.7 Explain the function of E.                                                           (2)

 5.8 Explain the function of F.                                                           (1)
                                                                                         [30]

Copyright reserved                                                          Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                   CIVIL TECHNOLOGY: WOODWORKING                           15

 QUESTION 6:          SUSPENDED FLOORS, STAIRCASES, IRON MONGERY,
                      DOORS AND JOINING (SPECIFIC)

 Start this question on a NEW page.

 6.1 FIGURE 6.1 below shows the floor plan of a straight flight of stairs with a
     landing. Study the picture and answer the questions that follow.

                                           FIGURE 6.1

       6.1.1    Identify parts A–H.                                                            (8)

       6.1.2    Explain the purpose of a newel or newel post.                                  (2)

       6.1.3    Differentiate between stairs with a landing and stairs with a half-landing     (4)

6.2    FIGURE 6.2 below shows the base of a dead shore. Study the picture and
       answer the questions that follow.

                                           FIGURE 6.2

      6.2.1     Explain in your own words the function of dead shore.                          (2)

      6.2.2     Identify the parts marked A, B and C.                                          (3)

      6.2.3     Explain the purpose of part D.                                                 (1)

Copyright reserved                                                               Please turn over

### Page 16

Downloaded from hlayiso.com
16                        CIVIL TECHNOLOGY: WOODWORKING             (EC/SEPTEMBER 2019)

6.3 FIGURE 6.3 below shows the sectional view of a door. Study the drawing and
    answer the questions that follow.

                                         FIGURE 6.3

      6.3.1     Identify parts A, B and C.                                           (3)

      6.3.2     Explain what is meant by the muntin of a door.                       (1)

      6.3.3     Explain the purpose of opening C in FIGURE 6.3.                      (2)

6.4 Explain the difference between a batten and a purlin.                            (4)

6.5 Draw on ANSWER SHEET C the different methods that can be used to fix floor
    joists to walls.                                                                (10)
                                                                                    [40]

                                                                        TOTAL:      200

Copyright reserved                                                     Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)               CIVIL TECHNOLOGY: WOODWORKING                              17

                                CIVIL TECHNOLOGY                   NAME:
      ANSWER SHEET       A           GENERIC

2.2     Use the information on ANSWER SHEET A and complete the floorplan to
        scale 1 : 100.

                                 2.2.I           2.2.J

                                            KITCHEN
                2.2.C   2.2.D   2.2.E
          BATHROOM

                                            LIVING ROOM

                 ROOM                                    2.2.G

                                   2.2.F          2.2.H

                                         2.2.A             2.2.B

                                                   Outside door at 2.2.A               2
                                                   Window at 2.2.B                     2
                                                   Water closet at 2.2.C               2
                                                   Washbasin at 2.2.D                  2
                                                   Wash tub at 2.2.E                   2
                                                   One-way switch-single pole at 2.2.F 2
                                                   Fluorescent light at 2.2.G          2
                                                   Socket outlet at 2.2.H              2
                                                   Grease trap at 2.2.I                2
                                                   Wall-mounted light at 2.2.J         2
                                                                               TOTAL: 20

Copyright reserved                                                              Please turn over

### Page 18

Downloaded from hlayiso.com



### Page 19

Downloaded from hlayiso.com
18                      CIVIL TECHNOLOGY: WOODWORKING                 (EC/SEPTEMBER 2019)

                            CIVIL TECHNOLOGY         NAME:
  ANSWER SHEET          B    WOODWORKING

4.5    Draw on ANSWER SHEET B to scale 1 : 10 a detailed sectional view of a
       closed (concealed) eave overhang of a roof truss.                         (22)

                                             CANDIDATE'S
 ASSESSMENT CRITERIA             MARKS          MARKS
 A Corrugated iron
    sheeting/IBR sheeting            1
 B Rafter                            1
 C Tie beam                          1
 D Wall plate                        2
 E Wall                              2
 F Plaster                           2
 G Downpipe                          2
 H Quarter-round (moulding)          1
 I  Soffit hanger                    2
 J Soffit board                      2
 K Gutter                            2
 L Fascia board                      2
 M Foot of purlin                    1
 N Purlin                            1
                     TOTAL:         22

Copyright reserved                                                       Please turn over

### Page 20

Downloaded from hlayiso.com



### Page 21

Downloaded from hlayiso.com
(EC/SEPTEMBER 2019)                  CIVIL TECHNOLOGY: WOODWORKING                 19

                                   CIVIL TECHNOLOGY    NAME:
  ANSWER SHEET           C          WOODWORKING

6.5 Draw on ANSWER SHEET C the different methods that can be used to fix floor
    joists to walls.                                                               (10)

 ASSESSMENT CRITERIA                MARKS      CANDIDATE'S
                                                  MARKS

 Joist build into wall                 2
 Floor joist                           2
 Scale                                 1
 Joist bolted to wall with truss
 hanger                                2
 Truss or joist hanger                 2
 Scale                                 1

                        TOTAL:         10

Copyright reserved                                                    Please turn over

### Page 22

Downloaded from hlayiso.com

         

### Page 23

Downloaded from hlayiso.com



         

### Page 24

Downloaded from hlayiso.com



## Related documents

- [CIV TECH GR12 QP SEPT2022 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-woodworking-english/c3b4a7c0-761a-45aa-a578-9b98afc86830) — Civil Technology · QP · 2022 · Eng
- [CIV TECH GR12 QP SEPT2022 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-civil-services-english/90720b3f-011a-43dc-8be9-862cb2bbc268) — Civil Technology · QP · 2022 · Eng
- [CIV TECH GR12 QP SEPT2021 English Construction](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2021-english-construction/551ab3e9-47c5-4ab0-a0cf-bc66dda5a956) — Civil Technology · QP · 2021 · Eng
- [CIVIL TECH GR12 QP Eng SEPT2019 CIVIL SERVICES](https://www.hlayiso.com/library/civil-tech-gr12-qp-eng-sept2019-civil-services/24d2e0b8-d851-4c36-a274-0e7449793231) — Civil Technology · QP · 2019 · Eng
- [CIVIL TECH GR12 QP AFR SEPT2019 KONSTRUKSIE](https://www.hlayiso.com/library/civil-tech-gr12-qp-afr-sept2019-konstruksie/c3787049-358b-4ee5-a539-4188e9f548b5) — Civil Technology · QP · 2019 · Afr
- [CIV TECH GR12 MEMO SEPT2023 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2023-construction-english/9ab6f3f0-4774-49bf-8311-57f09822adf6) — Civil Technology · Memo · 2023 · Eng

## More from Grade 12 Civil Technology

- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Memo · 2024 · Eng
- [Civil Technology Nov 2022 (Civil Services) MG Afr](https://www.hlayiso.com/library/civil-technology-nov-2022-civil-services-mg-afr/42b5315c-825c-40e3-b394-85e0253fc0fb) — Memo · 2023 · Afr
- [Civil Technology Nov 2023 (Construction) Eng](https://www.hlayiso.com/library/civil-technology-nov-2023-construction-eng/e6743728-8140-42ae-838d-282654a975a5) — QP · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
