# Civil Technology Grade 10 National November 2016 QP (Eng)

> Grade 10 Civil Technology question paper from the National November 2016 (English), 27 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/civil-technology-grade-10-exemplar-2016-eng/98f88865-6e9a-4f1b-a625-3f033a256a2d
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 10
- Document type: Question paper
- Year: 2016
- Exam period: National November
- Curriculum: CAPS
- Pages: 27

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 10](https://www.hlayiso.com/library/grade-10) › [Civil Technology](https://www.hlayiso.com/library/grade-10/civil-technology) › [Civil Technology Grade 10 National November 2016 QP (Eng)](https://www.hlayiso.com/library/civil-technology-grade-10-exemplar-2016-eng/98f88865-6e9a-4f1b-a625-3f033a256a2d)

## About this document

Civil Technology · Grade 10 · National November · 2016. Question paper, 27 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                 GRAAD 12

                                NATIONAL
                           SENIOR CERTIFICATE

                                 GRADE 10

                             CIVIL TECHNOLOGY

                               EXEMPLAR 2016

MARKS: 200

TIME: 3 hours

  This question paper consists of 21 pages, 5 answer sheets and 1 formula sheet.

Copyright reserved                                                   Please turn over

### Page 2

Downloaded from hlayiso.com
Civil Technology                              2                                    DBE/2016
                                   CAPS – Grade 10 Exemplar

REQUIREMENTS:

1.        Drawing instruments
2.        A non-programmable calculator
3.        ANSWER BOOK
INSTRUCTIONS AND INFORMATION
1.        This question paper consists of FOUR sections: SECTIONS A, B, C and D.
2.        SECTION A (QUESTIONS 1, 2, 3, and 4) is COMPULSORY for all learners.
3.        Choose ONE of the following SECTIONS according to the area of
          specialisation that you have registered for:
          SECTION B (QUESTIONS 5 and 6) – Construction
          SECTION C (QUESTIONS 7 and 8) – Civil Services
          SECTION D (QUESTIONS 9 and 10) – Woodworking
          NOTE:       If you answer the questions in SECTIONS B, C and D that you
                      have NOT registered for, they will NOT be marked.
4.        Number the answers correctly according to the numbering system used in this
          question paper.
5.        Start the answer to EACH question on a NEW page.
6.        Do NOT write in the margin of the ANSWER BOOK.
7.        You may use sketches to illustrate your answers.
8.        Write ALL calculations and answers in the ANSWER BOOK or on the
          attached ANSWER SHEETS. Answers to calculations should be rounded off
          to TWO decimal places. Show the units of ALL answers.
9.        Use the mark allocation as a guide to the length of your answers.
10.       Make drawings and sketches in pencil, fully dimensioned and neatly finished
          off with descriptive titles and notes to conform to the SANS/SABS Code of
          Practice for Building Drawings.
11.       For the purpose of this question paper, the size of a brick should be taken as
          220 mm x 110 mm x 75 mm.
12.       Use your own discretion where dimensions and/or details have been omitted.
13.       All dimensions are in millimetres, unless stated otherwise.
14.       Answer QUESTIONS on the attached ANSWER SHEETS, as prescribed in
          each question where applicable.
15.       Drawings in the question paper are NOT to scale due to electronic transfer.

Copyright reserved                                                            Please turn over

### Page 3

Downloaded from hlayiso.com
Civil Technology                               3                                    DBE/2016
                                    CAPS – Grade 10 Exemplar

SECTION A: GENERICS (COMPULSORY)

QUESTION 1: SAFETY

1.1       FIGURE 1.1 below shows a worker and a visitor on a construction site.

                                            FIGURE 1.1

          1.1.1       What safety equipment can the visitor use to prevent falling objects
                      from injuring him?                                                          (1)

          1.1.2       Explain TWO safety measures that must be implemented to ensure
                      the safety of visitors and workers on a site.                               (2)

          1.1.3       Identify ONE unsafe act that the worker is performing.                      (1)
1.2       You are working with electrical cutting tools on a site. Name any TWO types
          of safety equipment that you may use to protect yourself against injuries.              (2)

1.3       Describe TWO safety precautions that have to be considered when working
          with hand tools.                                                                        (2)

1.4       Name THREE elements that must be present in a fire for it to be able to burn.           (3)

1.5       Explain THREE factors that must be considered when stacking material in
          a workshop.                                                                             (3)

1.6       Predict THREE consequences of the behaviour of a worker on a building site
          when the worker is intoxicated because of alcohol or drug abuse.                        (3)

1.7       Describe THREE visible symptoms that a worker is under the influence of
          drugs.                                                                                  (3)
                                                                                                  [20]

Copyright reserved                                                             Please turn over

### Page 4

Downloaded from hlayiso.com
Civil Technology                               4                                     DBE/2016
                                    CAPS – Grade 10 Exemplar

QUESTION 2: MATERIALS, TOOLS AND EQUIPMENT

Start this question on a NEW page.

2.1       Choose a description from COLUMN B that matches an item in COLUMN A.
          Write only the letter (A–L) next to the question number (2.1.1–2.1.10) in the
          ANSWER BOOK, for example 2.1.11 M.

                      COLUMN A                                  COLUMN B
          2.1.1       Concrete                 A     not brittle due to heat treatment

          2.1.2       Saligna                  B     can be cast in any shape/mould

          2.1.3       Amount of water in       C     made up of an uneven number of
                      concrete                       layers of veneer

          2.1.4       SA pine                  D     light-weight metal

          2.1.5       Cement                   E     this material is baked

          2.1.6       Copper                   F     will influence the workability of fresh
                                                     concrete
          2.1.7       Plywood
                                               G     bonding ingredient in concrete,
          2.1.8       Aluminium                      mortar and screed

          2.1.9       Clay bricks              H     soft wood

          2.1.10      Malleable cast iron      I     good conductor of heat

                                               J     hardwood

                                               K     available in even layers

                                               L     curing is required for 60 days
                                                                                   (10 x 1)        (10)

2.2       Various options are given as possible answers to the following questions.
          Choose the answer and write only the letter (A–D) next to the question
          number (2.2.1–2.2.10) in the ANSWER BOOK, for example 2.2.11 C.

          2.2.1       … may be used for formwork.

                      A   Block board
                      B   Plywood
                      C   Shutter board
                      D   All the above-mentioned                                                  (1)

Copyright reserved                                                              Please turn over

### Page 5

Downloaded from hlayiso.com
Civil Technology                               5                                      DBE/2016
                                    CAPS – Grade 10 Exemplar

          2.2.2       … can be soft-soldered, silver-soldered and brazed.

                      A   Bronze
                      B   Copper
                      C   Lead
                      D   Zinc                                                                      (1)

          2.2.3       … form(s) waterproof joints because it repels water.

                      A   PVC adhesives
                      B   Mortar
                      C   Silicon
                      D   Wood glue                                                                 (1)

          2.2.4       A … is the tool recommended for mixing concrete and mortar.

                      A   pick
                      B   round shovel
                      C   square shovel
                      D   spade                                                                     (1)

          2.2.5       A …is used for measuring when laying out buildings.

                      A   steel tape
                      B   folding rule
                      C   steel square
                      D   line and pins                                                             (1)

          2.2.6       A … is used by a plasterer to place plaster in difficult corners.

                      A   mastic trowel
                      B   long jointer
                      C   short jointer
                      D   pointing trowel                                                           (1)

          2.2.7       A … may be used to cut copper pipes neatly and accurately.

                      A   tenon saw
                      B   hacksaw
                      C   pipe cutter
                      D   grinder                                                                   (1)

          2.2.8       A/An … may be used to clamp galvanised pipes when they are
                      being cut to size.

                      A   pipe wrench
                      B   adjustable spanner
                      C   pipe vice
                      D   pipe cutter                                                               (1)

Copyright reserved                                                               Please turn over

### Page 6

Downloaded from hlayiso.com
Civil Technology                               6                                   DBE/2016
                                    CAPS – Grade 10 Exemplar

          2.2.9       A … may be used to level fresh concrete.

                      A   spirit level
                      B   steel square
                      C   long jointer
                      D   straight edge                                                         (1)

          2.2.10      A … may be used to tap joints into place.

                      A   brick trowel
                      B   wooden mallet
                      C   mortise chisel
                      D   plumb bob                                                             (1)

2.3       The table below shows pictures of hand tools that are used on sites and in
          workshops. Write down the NAME and ONE use of EACH tool next to the
          question numbers (2.3.1–2.3.5) in the ANSWER BOOK.

                      2.3.1                     2.3.2                    2.3.3

                      2.3.4                     2.3.5                                           (10)

2.4       Describe TWO properties of EACH of the following materials:

          2.4.1       Sand                                                                      (2)

          2.4.2       Stainless steel                                                           (2)

          2.4.3       Mastic sealant                                                            (2)

2.5       Discuss TWO properties of PVC adhesives.                                              (2)

2.6       Differentiate between a steel square and a try square in terms of use.                (2)
                                                                                                [40]

Copyright reserved                                                           Please turn over

### Page 7

Downloaded from hlayiso.com
Civil Technology                              7                                 DBE/2016
                                   CAPS – Grade 10 Exemplar

QUESTION 3: GRAPHICS AS MEANS OF COMMUNICATION

Start this question on a NEW page.

3.1       Define the term CAD, as used in drawing.                                            (1)

3.2       Draw a neat, freehand, isometric sketch of a standard solid brick, in good
          proportion, in the ANSWER BOOK.                                                     (5)

3.3       FIGURE 3.3 shows an isometric view of a cement hollow block.
          Use ANSWER SHEET 3.3 and draw, to scale 1 : 5, the front, left and top
          views of this cement hollow block in first-angle orthographic projection.
          The thickness of the concrete around the hollow is 30 mm all around.

          Show the following in the drawing:

          •    ALL hidden detail
          •    Construction lines
          •    Dimensions for the height and length of the block
          •    Print the title and the scale below the drawing.

                                                                   FRONT

                                         FIGURE 3.3                                           (17)

Copyright reserved                                                         Please turn over

### Page 8

Downloaded from hlayiso.com
Civil Technology                              8                                   DBE/2016
                                   CAPS – Grade 10 Exemplar

3.4       FIGURE 3.4 shows the line diagram of a plan of an office with a kitchen.

                                               7 000

                                          W1

                        4 000
                                          Office              Kitchen
                                                                        W2

                                                             D1
                                D1

                                           FIGURE 3.4

          On ANSWER SHEET 3.4 develop and draw, to scale 1 : 50, the floor plan of
          the office and kitchen. Use the specifications given below.

          Specifications:

          •    The external measurements of the building are 7 000 mm x 4 000 mm.
          •    The internal width of the kitchen is 2 000 mm.
          •    External walls are 220 mm thick.
          •    Internal wall is 110 mm thick.
          •    All door openings are 900 mm wide.
          •    The external door is placed 500 mm from the left side of the building,
               measured from the outside of the wall.
          •    The internal door is placed 230 mm from the inside of the external wall.
          •    Window 1 is 2 000 mm wide and is placed in the middle of the office wall.
          •    Window 2 is 1 500 mm wide and is placed in the middle of the kitchen
               wall.                                                                            (15)

          Indicate the internal dimensions of the kitchen.                                      (2)
                                                                                                [40]

Copyright reserved                                                           Please turn over

### Page 9

Downloaded from hlayiso.com
Civil Technology                              9                                      DBE/2016
                                   CAPS – Grade 10 Exemplar

QUESTION 4: JOINING AND QUANTITIES

Start this question on a NEW page.

4.1       Explain THREE advantages of using nails over screws.                                   (3)

4.2       Explain THREE advantages of using screws over nails.                                   (3)

4.3       Indicate where the following fasteners may be used:

          4.3.1       Countersunk head screw                                                     (1)

          4.3.2       Drywall screw                                                              (1)

          4.3.3       Round wire nail                                                            (1)

          4.3.4       Panel pin                                                                  (1)

4.4       FIGURE 4.4 below shows the front and left views of a straight foundation.

                                                                                       150

                                        3 000                              600

                                  Front view                             Left view
                                                FIGURE 4.4

          4.4.1       Determine the length of the concrete foundation in metres.                 (1)

          4.4.2       Determine the width of the concrete foundation in metres.                  (1)

          4.4.3       Determine the depth of the concrete foundation in metres.                  (1)

          4.4.4       Calculate the volume of concrete required for this foundation.
                      Round off your answer to ONE decimal.                                      (5)

Copyright reserved                                                            Please turn over

### Page 10

Downloaded from hlayiso.com
Civil Technology                               10                                    DBE/2016
                                    CAPS – Grade 10 Exemplar

4.5       FIGURE 4.5 below shows the floor plan of a building. Study the sketch and
          answer the following questions.

                                                                             6 440

                                            10 440

                                             FIGURE 4.5

          4.5.1       Calculate the length of the skirting for the building if the door
                      opening is 900 mm wide. Ignore the reveals at the door opening.           (9)

          4.5.2       Calculate the area of the floor.                                          (4)

Copyright reserved                                                          Please turn over

### Page 11

Downloaded from hlayiso.com
Civil Technology                                 11                                 DBE/2016
                                      CAPS – Grade 10 Exemplar

4.6       FIGURE 4.6 below shows a foundation trench of 8 metres in length that has
          been excavated and cast with concrete.

                                                          1 350

                                                                  700

                                200

                                                  600

                                              FIGURE 4.6

          4.6.1       Calculate the volume of soil that has been excavated from
                      the trench.                                                                 (5)

          4.6.2       Calculate the area of the wall if the wall stops 150 mm from the
                      edge of the foundation on both sides.                                       (4)
                                                                                                  [40]

                                                                        TOTAL SECTION A:          140

Copyright reserved                                                             Please turn over

### Page 12

Downloaded from hlayiso.com
Civil Technology                             12                                    DBE/2016
                                  CAPS – Grade 10 Exemplar

SECTION B: CONSTRUCTION

QUESTION 5: FOUNDATIONS, CONCRETE AND BRICKWORK

Start this question on a NEW page.

5.1       Identify the tools illustrated in FIGURE 5.1.1 and FIGURE 5.1.2 below.

          5.1.1

                                                    [Source: Google Images]
                                                FIGURE 5.1.1                                  (1)

          5.1.2

                                                    [Source: Google Images]
                                                FIGURE 5.1.2                                  (1)

5.2       Describe the meaning of the safety sign illustrated in FIGURE 5.2 below.

                                          FIGURE 5.2                                          (1)

5.3       Explain TWO uses of a block brush.                                                  (2)

5.4       Explain THREE reasons for compacting soil during a construction process.            (3)

5.5       Explain the purpose of foundations.                                                 (2)

Copyright reserved

### Page 13

Downloaded from hlayiso.com
Civil Technology                             13                                   DBE/2016
                                  CAPS – Grade 10 Exemplar

5.6       Differentiate between a strip foundation and a stepped foundation by means
          of neat, two-dimensional freehand sketches in the ANSWER BOOK.                        (4)

5.7       The foundation of a building need to be cast in phases. Draw a freehand
          drawing in the ANSWER BOOK to show an exploded view of how fresh
          concrete should be joined to the existing concrete to ensure a good bond
          between the two.                                                                      (4)

5.8       When damage is detected in a concrete structure, this damage must be
          evaluated and repaired. Describe, in the correct sequence, the steps that
          should be followed to remedy the situation.                                           (4)

5.9       Explain the purpose of reinforcing brickwork.                                         (2)

5.10      Name any TWO methods of tying reinforcement bars together.                            (2)

5.11      Concrete with a volume of 5 m3 and a mixing ratio of 1 : 3 : 6 (1 part cement,
          3 parts sand and 6 parts stone) needs to be mixed by hand. Calculate the
          volume of sand that will be required for this batch of concrete.

          HINT: Use the formulae in the formulae sheet.                                         (4)
                                                                                                [30]

Copyright reserved                                                           Please turn over

### Page 14

Downloaded from hlayiso.com
Civil Technology                              14                                      DBE/2016
                                   CAPS – Grade 10 Exemplar

QUESTION 6: FORMWORK

Start this question on a NEW page.

6.1       Name ONE type of nail that may be used to join the different members of
          formwork.                                                                                 (1)

6.2       FIGURE 6.2 below shows the horizontal cross section of the formwork for
          a concrete column. Name the parts labelled A, B and C. Write only the
          answer next to the letter (A–C) in the ANSWER BOOK.

                                                                             A

                                                                             B

                                                                             C

                                         FIGURE 6.2                                                 (3)

6.3       Explain what is meant by the term striking of formwork.                                   (1)

6.4       Describe TWO factors that must be considered while striking of formwork
          is taking place.                                                                          (2)

6.5       Plywood may be used for formwork. Describe THREE properties of plywood.                   (3)

6.6       Draw a neat, two-dimensional freehand sketch, in good proportion, in the
          ANSWER BOOK to illustrate the front elevation of a soldier course, as used in
          brickwork. Show only SIX bricks.                                                          (3)

6.7       Use ANSWER SHEET 6.7 and draw, to scale 1 : 10, the front elevation of
          a brick wall built in stretcher bond to show raking back on the right-hand side
          of the wall and toothing on the left-hand side of the wall. The first course of
          the wall is five bricks long and the wall is five courses high. Label the drawing
          to indicate the raking back and the toothing.                                             (10)
Copyright reserved                                                               Please turn over

### Page 15

Downloaded from hlayiso.com
Civil Technology                            15                                DBE/2016
                                 CAPS – Grade 10 Exemplar

6.8       Draw the symbol for concrete.                                                     (2)

6.9       FIGURE 6.9 below shows a baseplate that has to be anchored to a concrete
          base. Name TWO fasteners that may be used to secure the baseplate to the
          concrete base.

                                          FIGURE 6.9                                        (2)

6.10      Name ONE fastener that may be used to join wood to concrete.                      (1)

6.11      Describe TWO methods to store radioactive material.                               (2)
                                                                                            [30]

                                                                TOTAL SECTION B:            60

Copyright reserved                                                       Please turn over

### Page 16

Downloaded from hlayiso.com
Civil Technology                               16                                     DBE/2016
                                    CAPS – Grade 10 Exemplar

SECTION C: CIVIL SERVICES
QUESTION 7: CONSTRUCTION, STORM WATER AND ROOF WORK
Start this question on a NEW page.
7.1       Explain THREE good lifting techniques that should be applied when lifting
          heavy loads manually.                                                                     (3)
7.2       On what geometrical theorem is the 3-4-5 method based?                                    (1)
7.3       In your ANSWER BOOK, draw a freehand sketch of TWO consecutive
          plan courses of a half-brick wall in stretcher bond. Show SIX bricks for the
          first course.                                                                             (4)
7.4       Describe THREE factors that may lead to workers being injured when they
          work in deep excavations.                                                                 (3)
7.5       State the ingredients of mortar.                                                          (3)
7.6       Differentiate between class 0 and class 2 copper pipes in terms of wall
          thickness and use. Copy the table below in the ANSWER BOOK and
          complete it.
             TYPE            WALL THICKNESS                              USE
            Class 0
            Class 2                                                                                 (4)
7.7       FIGURE 7.7 below shows a front and a top view of a square down pipe with
          a grooved-seam lap joint. On ANSWER SHEET 7.7, project and draw, from
          the given views, the development of the square down pipe plus the allowance
          for the seam.

                                         A₁    D₁

                                     A              D      GROOVED-SEAM
                                                           LAP JOINT

                                    B               C

                                              FIGURE 7.7                                            (8)

7.8       Large amounts of storm water on a site must be disposed of. Describe TWO
          methods that may be used to channel the storm water to the catchment
          areas.                                                                                    (2)
7.9       You have to install a gutter onto a roof. Explain, in your own words, the
          factors that will determine the slope (fall) and direction of the exit of the water
          in the gutter.                                                                            (2)
                                                                                                    [30]
Copyright reserved                                                               Please turn over

### Page 17

Downloaded from hlayiso.com
Civil Technology                                17                                DBE/2016
                                     CAPS – Grade 10 Exemplar

QUESTION 8: HOT- AND COLD-WATER SUPPLY AND SANITARY FITMENTS

Start this question on a NEW page.

8.1       Name TWO properties of clean water.                                                   (2)

8.2       Explain the water cycle in your own words.                                            (4)

8.3       Differentiate between water obtained from wells and water obtained from
          boreholes in terms of the disadvantages of each.                                      (2)

8.4       Describe TWO methods that may be used to prevent water pipes from
          freezing.                                                                             (2)

8.5       Explain TWO purposes of EACH of the following valves:

          8.5.1       Pressure-reducing (pressure-control) valve                                (2)

          8.5.2       Safety valve                                                              (2)

8.6       Explain the term radiation.                                                           (2)

8.7       Differentiate between a balanced water installation and an unbalanced water
          installation for a house.                                                             (2)

8.8       FIGURE 8.8 below shows a sanitary fitment.

                                               [Source: Google Images]
                                             FIGURE 8.8

          8.8.1       Identify the sanitary fitment above.                                      (1)

          8.8.2       Draw the symbol for the sanitary fitment in FIGURE 8.8, as it will
                      appear on a floor plan.                                                   (2)

Copyright reserved                                                           Please turn over

### Page 18

Downloaded from hlayiso.com
Civil Technology                             18                                    DBE/2016
                                  CAPS – Grade 10 Exemplar

8.9       FIGURE 8.9 below shows a drawing of the exploded view of a compression
          joint. Identify parts A, B and C.

                                           A          B   C
                                        FIGURE 8.9                                               (3)

8.10      Make a neat freehand drawing, in good proportion, of the sectional view of a
          grooved-seam lap joint.                                                                (2)

8.11      FIGURE 8.11 below shows a line diagram of part of the pipe layout of
          a shower. Calculate the total length of pipe and the number of fittings needed
          for the installation of this shower by completing the quantity list below
          FIGURE 8.11. Write down only the answer next to the question number
          (8.11.1–8.11.4) in the ANSWER BOOK.

                                                     50        Fitting to attach
                                                               shower rose

                            500

                     250                       250

                           200       200

                                           FIGURE 8.11

           MATERIAL                DESCRIPTION                  QUANTITY LENGTH
           Copper                       8.11.1                      3
           Copper                       8.11.2                      1
           Brass           Ø15 mm straight connector, female        1
           Copper               Ø15 mm class 0 pipe                 1      500
           Copper               Ø15 mm class 0 pipe               8.11.3   250
           Copper               Ø15 mm class 0 pipe                 2      200
           Copper               Ø15 mm class 0 pipe                 1       50
           Total length                                                   8.11.4                 (4)
                                                                                                 [30]

                                                                   TOTAL SECTION C:              60

Copyright reserved                                                            Please turn over

### Page 19

Downloaded from hlayiso.com
Civil Technology                               19                                  DBE/2016
                                    CAPS – Grade 10 Exemplar

SECTION D: WOODWORKING

QUESTION 9: CASEMENTS
Start this question on a NEW page.
9.1       Draw a horizontal section through a tree trunk to show the following parts:
          •    Pith/Core/Heart
          •    Heart wood
          •    Sapwood
          •    Annual rings
          •    Medullary rays
          •    Bark
          •    Cambium layer
          Label any THREE parts of the drawing.                                                  (10)

9.2       Differentiate between a dead knot and a live knot.                                     (2)
9.3       Explain ONE use of a mortice gauge.                                                    (1)
9.4       Explain the purpose of the cross peen in a Warrington hammer.                          (1)
9.5       FIGURE 9.5 below shows a drawing of the external elevation of a single
          casement within a frame. Study the drawing and answer the questions that
          follow.

                                                                     A

                                                                    B

                                                                     C

                                                                    D
                       H
                                                                    E

                                                                    F
                                                                    G
                                               FIGURE 9.5
          9.5.1       Identify parts A to G.                                                     (7)
          9.5.2       Name the component that may be used to keep D in place.                    (1)
          9.5.3       Use instruments and draw, in good proportion, a horizontal section
                      though part H in the ANSWER BOOK.                                          (5)
9.6       Explain THREE purposes of a rebate in a frame.                                         (3)
                                                                                                 [30]

Copyright reserved                                                            Please turn over

### Page 20

Downloaded from hlayiso.com
Civil Technology                                 20                              DBE/2016
                                      CAPS – Grade 10 Exemplar

QUESTION 10: DOORS

Start this question on a NEW page.

10.1      Predict ONE negative consequence of poor housekeeping.                               (1)

10.2      Name TWO materials that may be used as a panel for a hollow flush panel
          door.                                                                                (2)

10.3      You are going to hang a hollow flush panel door. The door is longer than the
          height of the opening. Name the type of hand saw that you will use to cut the
          door to fit into the opening of the door frame.                                      (1)

10.4      Name ONE type of glue that may be used to join members of a hollow flush
          panel door.                                                                          (1)

10.5      Explain ONE property of glue that makes it suitable to use for the assembling
          of external doors.                                                                   (1)

10.6      FIGURE 10.6 below shows the front elevation of a two-panel door. The door
          is fitted with flat 10 mm thick plywood panels which are embedded 10 mm into
          the stiles and rails. Study the drawing and complete the cutting list on the
          next page (page 21) by writing down only the answer next to the question
          number (10.6.1–10.6.9) in the ANSWER BOOK. Through mortice and tenon
          joints are used between the rails and the stiles.

          NOTE: Show actual sizes in your answer.

                                                                 114 x 44

                                                                 114 x 44
                                738
                                                                 114 x 44

                                                                 220 x 44
                        2 032

                                738

                                                                 220 x 44

                                             813

                                             FIGURE 10.6

Copyright reserved                                                          Please turn over

### Page 21

Downloaded from hlayiso.com
Civil Technology                             21                               DBE/2016
                                  CAPS – Grade 10 Exemplar

   MEMBER/            QUANTITY/      LENGTH     WIDTH        THICKNESS   MATERIAL
 DESCRIPTION           NUMBER
                      REQUIRED
 Stiles                 10.6.1        2 030      10.6.2         44        Meranti
 Top rail                 1           10.6.3      114          10.6.4     Meranti
 10.6.5                   1            813       10.6.6         44         10.6.7
 Bottom rail            10.6.8         813        220           44        Meranti
 Panels                   2            758       10.6.9         10        Plywood        (9)

10.7      Use drawing instruments and draw a neat, two-dimensional drawing to show
          how the tongued and grooved battens are joined to the ledge in a ledged
          batten door. Show part of the ledge and only TWO tongued and grooved
          battens in your drawing.                                                       (5)

10.8      Use ANSWER SHEET 10.8 and draw, to scale 1 : 10, the internal elevation of
          a ledged batten door to the following specifications:

          •    Size of door: height is 2 032 mm and the width is 813 mm
          •    Tongued and grooved battens: 100 mm x 22 mm
          •    Ledge: 150 mm x 22 mm
          •    The top and bottom ledges are 150 mm away from the top and bottom of
               the door.
          •    Label any THREE parts of the door.                                        (10)
                                                                                         [30]

                                                                   TOTAL SECTION D:      60
                                                                      GRAND TOTAL:       200

Copyright reserved

### Page 22

Civil Technology
                        Downloaded from hlayiso.com                                     DBE/2016
                                 CAPS – Grade 10 Exemplar

SECTION A: ANSWER SHEETS

SURNAME AND NAME:
CLASS:

SECTION A: ANSWER SHEET 3.3

                                                            CRITERIA                    MARK       LM
                                                            Drawing of external lines      7
                                                            Hidden detail                  6
                                                            Printing of title              1
                                                            Printing of scale              1
                                                            Application of scale           2
                                                            TOTAL                         17

Copyright reserved

### Page 23

Civil Technology
                        Downloaded from hlayiso.com                                     DBE/2016
                                 CAPS – Grade 10 Exemplar

SURNAME AND NAME:
CLASS:                                                      CRITERIA                         MARK   LM
                                                            External walls drawn correctly     4
SECTION A: ANSWER SHEET 3.4                                 Internal wall drawn correctly      1
                                                            Doors drawn correctly              2
                                                            Windows drawn correctly            2
                                                            Correct placement of doors         2
                                                            Correct placement of windows       2
                                                            Dimension of internal width of
                                                                                              2
                                                            kitchen
                                                            Application of scale               2
                                                            TOTAL                             17

Copyright reserved

### Page 24

Civil Technology
                        Downloaded from hlayiso.com                                         DBE/2016
                                 CAPS – Grade 10 Exemplar

SECTION B: ANSWER SHEETS

SURNAME AND NAME:
CLASS:
                                                                      CRITERIA       MARK       LM
SECTION B: ANSWER SHEET 6.7                                 Correctness of drawing     6
                                                            Labelling                  2
                                                            Application of scale       2
                                                            TOTAL                     10

Copyright reserved

### Page 25

Civil Technology
                            Downloaded from hlayiso.com         DBE/2016
                                     CAPS – Grade 10 Exemplar

SECTION C: ANSWER SHEETS

SURNAME AND NAME:
CLASS:

SECTION C: ANSWER SHEET 7.7

      A₁ D₁            A₁

 A    A₁ D₁        D A₁

 B                 C

Copyright reserved

### Page 26

Downloaded from hlayiso.com
Civil Technology                                       DBE/2016
                            CAPS – Grade 10 Exemplar

SECTION D: ANSWER SHEETS

SURNAME AND NAME:
CLASS:

SECTION D: ANSWER SHEET 10.8

Copyright reserved

### Page 27

Downloaded from hlayiso.com
Civil Technology                                                            DBE/2016
                                 CAPS – Grade 10 Exemplar

                                   FORMULA SHEET

               AREA OF                FORMULA                 FORMULA
                                      (in words)             (In symbols)
         Square                       side x side                 sxs
         Rectangle                 length x breadth               ℓxb
         Right-angled
                                  ½ x base x height             ½b x h
         triangle

         Equilateral triangle/
                                  ½ x base x height             ½b x h
         Isosceles triangle

Calculation of volumes of materials for concrete

Volume of material = Volume of concrete required x Mix ratio of material
                                                     Total mix ratio

Copyright reserved

## Related documents

- [Civil Technology Grade 10 Exemplar 2016 Memo Eng](https://www.hlayiso.com/library/civil-technology-grade-10-exemplar-2016-memo-eng/63dec461-5be1-4830-a9f1-26a2b492e4ec) — Civil Technology · Memo · 2016 · Eng

## Collection

- [Grade 10 past papers](https://www.hlayiso.com/grade-10/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
