# Civil Technology Grade 12 NSC June 2021 Question Paper (Eng)

> Grade 12 Civil Technology question paper from the NSC June Exam 2021 (English), 25 pages. Read online or get the free PDF download, memo linked when available.

- Page: https://www.hlayiso.com/library/civil-technology-may-june-2021-woodworking-eng/8f870317-4f98-4448-b660-0d528b30c2a4
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2021
- Exam period: NSC June Exam
- Curriculum: CAPS
- Pages: 25

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 NSC June 2021 Question Paper (Eng)](https://www.hlayiso.com/library/civil-technology-may-june-2021-woodworking-eng/8f870317-4f98-4448-b660-0d528b30c2a4)

## About this document

Civil Technology · Grade 12 · NSC June Exam · 2021. Question paper, 25 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

              SENIOR CERTIFICATE EXAMINATIONS/
          NATIONAL SENIOR CERTIFICATE EXAMINATION

                      CIVIL TECHNOLOGY: WOODWORKING

                                        2021

                                                                        MARKS: 200

                                                                      TIME: 3 hours

            This question paper consists of 17 pages and 7 answer sheets.

Copyright reserved                                                    Please turn over

### Page 2

Downloaded from hlayiso.com
Civil Technology: Woodworking                    2                                 DBE/2021
                                              SC/NSC

REQUIREMENTS:

1.        Drawing instruments

2.        A non-programmable calculator

3.        ANSWER BOOK

INSTRUCTIONS AND INFORMATION

1.        This question paper consists of SIX questions.

2.        Answer ALL the questions.

3.        Read all the questions carefully.

4.        Answer each question as a whole. Do NOT separate subsections of
          questions.

5.        Number the answers correctly according to the numbering system used in this
          question paper.

6.        Start the answer to EACH question on a NEW page.

7.        Do NOT write in the margins of the ANSWER BOOK.

8.        You may use sketches to illustrate your answers.

9.        Write ALL calculations and answers in the ANSWER BOOK or on the
          attached ANSWER SHEETS. The SI unit for answers must be indicated next
          to the answer.

10.       Use the mark allocation as a guide to the length of your answers.

11.       Make drawings and sketches in pencil, fully dimensioned and neatly finished
          off with descriptive titles and notes to conform to the SANS/SABS Code of
          Practice for Building Drawings.

12.       For the purpose of this question paper, the size of a brick should be taken as
          220 mm x 110 mm x 75 mm.

13.       Use your own discretion where dimensions and/or details have been omitted.

14.       Answer QUESTIONS 2, 3.6, 4.8, 5.2, 5.4, 5.5 and 6.9.2 on the attached
          ANSWER SHEETS using drawing instruments, where necessary.

15.       Write your CENTRE NUMBER and EXAMINATION NUMBER on every
          ANSWER SHEET and hand them in with your ANSWER BOOK, whether you
          have used them or not.

16.       Drawings in the question paper are NOT to scale due to electronic transfer.

17.       Google Images were used as the source of all photographs and pictures.

18.       Write neatly and legibly.
Copyright reserved                                                            Please turn over

### Page 3

Downloaded from hlayiso.com
Civil Technology: Woodworking                   3                                   DBE/2021
                                             SC/NSC

QUESTION 1:          OHSA, SAFETY, MATERIALS,              TOOLS,       EQUIPMENT    AND
                     JOINING (GENERIC)

Start this question on a NEW page

1.1       Give ONE word/term for each of the following descriptions by choosing a
          word/term from the list below. Write only the word/term next to the question
          numbers (1.1.1. to 1.1.5) in the ANSWER BOOK, e.g. 1.1.6 casement

                      curing;   electroplating; galvanising; powder coating;
                                 paint; turpentine; sanding sealer

          1.1.1       Available in a water- or oil-based liquid                                  (1)

          1.1.2       Allows concrete to achieve its optimal strength                            (1)

          1.1.3       Coating a metal by the process of electrolysis                             (1)

          1.1.4       Can be melted again because no chemical process is involved                (1)

          1.1.5       Adds strength to the original uncoated metal                               (1)

1.2       FIGURE 1.2 below shows equipment that is used on a construction site.

                                           A                      B
                                               FIGURE 1.2

          1.2.1       State TWO materials that the equipment can be manufactured of.             (2)

          1.2.2       Deduce from FIGURE 1.2 the safest option to use, A or B.
                      Motivate your answer.                                                      (2)

Copyright reserved                                                            Please turn over

### Page 4

Downloaded from hlayiso.com
Civil Technology: Woodworking                     4                                     DBE/2021
                                               SC/NSC

          1.2.3       Explain the purpose of the equipment in FIGURE 1.2.                            (1)

          1.2.4       How far from a wall should the base of a ladder be placed to
                      ensure that it is positioned safely?                                           (1)

1.3       A laser level is often used in construction.

          1.3.1       Explain what you will determine if you use the laser level in EACH
                      of the following cases:

                     (a)    When installing a sewerage system for a building                         (1)

                     (b)    When laying tiles against a wall                                         (1)

          1.3.2       Explain what will happen if the tripod is not wide enough when
                      setting up the laser level.                                                    (1)

1.4       Explain what will happen if a worker manually lifts excessively heavy loads.               (1)

1.5       The use of scaffolds is not permitted, unless inspected.

          1.5.1       When should scaffolding be inspected?                                          (1)

          1.5.2       Who is responsible for the inspection of the scaffolding?                      (1)

1.6       FIGURE 1.6 below shows a joining fixture that can be used on building sites.

                                                 FIGURE 1.6

          1.6.1       Identify the joining fixture.                                                  (1)

          1.6.2       Name the part that should be used with the joining fixture.                    (1)

          1.6.3       Explain why it is a better option to use this joining fixture to join two
                      steel sections.                                                                (1)
                                                                                                     [20]

QUESTION 2: GRAPHICS AS MEANS OF COMMUNICATION (GENERIC)

Start this question on a NEW page.

FIGURE 2 on the next page shows a drawing that appears on a building plan. Analyse
the drawing and complete the table on ANSWER SHEET 2.

Copyright reserved                                                                Please turn over

### Page 5

Downloaded from hlayiso.com
           Civil Technology: Woodworking                       5                                           DBE/2021
                                                            SC/NSC

                                                                                      NOTES:
                                                                                      Contractors must verify all
                                                                                      dimensions and levels on site before
                                               PLOT 53                                commencing work. Architects are to
                                                                                      be notified of any discrepancies
                                               25 000                                 immediately.

                                                                                      ARCHITECT'S SIGNATURE ………………….

                                             14 100                                   CLIENT'S SIGNATURE ……………………….

                                                                                  1
                                                                     10 000
                         3 000   4 000           10 000     3 000                     The following symbol must be
                                                                                      indicated on a floor plan:
                                                                                  2    One-way switch – double-pole
                3 000
                                                                                      The following item must be installed
                                                                                  3   in the bathroom:
                4 000
                                                                                  4

 PLOT 49                                                                                       10

35 000                                     NEW
                                         DWELLING
                12 000                                               20 000

                                                                                  5
                                                                                      Main sewer line to be installed at a
                                                                                      slope of 1 : 40.

                                                                                      Brick force to be installed every
                                                                                      third course up to window height and
                4 000
                          PLOT 51
                                                                                      on every course from the top of the
                                                                                      window up to wall plate level.

                3 000                                                                 Pavement of 1,5 m wide must be
                                                                     5 000            paved.
                                                                                  6

                PAVEMENT 1 500 WIDE                                                        1          30/05/2021   RECTIFY
                                                                                                                   DIMENSION
                                                                                  7
                                                                                       REVISION        DATE        DESCRIPTION

                                          PROTEA STREET                               PRINTED BY:              DATE OF PRINT:
                                                                                      HENSON PRINTERS          01/04/2021
                                                             8
                                                                                      DRAWING TITLE:
                                                                                      SITE PLAN PLOT 51
                                          PAVEMENT
                                                                                      PROJECT:
                                                                                      PROPOSED NEW DWELLING ON PLOT 51,
                                                                                      DEEP RIVER

                                                                                      PROJECT NO.             DRAWING NO.
                                                                                      GR 448-209              559P9

                                                                                        DATE     DRAWN        CHECKED SCALE
                                                                                      16/04/2021 JP NSIKI     P GUNTER 1 : 200

                                                                                                    REFERENCE CODE
                                    SCALE 1 : 200                             9                        QP 2–2021

                                                          FIGURE 2                                                    [40]
           Copyright reserved                                                                        Please turn over

### Page 6

Downloaded from hlayiso.com
Civil Technology: Woodworking                     6                                    DBE/2021
                                               SC/NSC

QUESTION 3:          CUPBOARDS,CASEMENTS, WALL-PANELLING AND QUANTITIES
                     (SPECIFIC)

Start this question on a NEW page.

3.1       FIGURE 3.1 below shows the inside of a built-in cupboard without doors.
          Study the sketch and answer the questions that follow.

                                                                             A

                                                                             B

                     D

                     E

                                                                             C

                                                FIGURE 3.1

          3.1.1          Describe the purpose of parts A, B and C respectively.                      (3)

          3.1.2          Differentiate between parts D and E by identifying it.                      (2)

          3.1.3          State the depth of a built-in cupboard.                                     (1)

3.2       Name TWO board products that will be most suitable for the construction of
          the carcass of a built-in cupboard.                                                        (2)

3.3       Describe the advantage of a built-in cupboard that is built up to ceiling height.          (1)

Copyright reserved                                                                Please turn over

### Page 7

Downloaded from hlayiso.com
Civil Technology: Woodworking                  7                                    DBE/2021
                                            SC/NSC

3.4       FIGURE 3.4 below shows an external elevation of an incomplete casement.
          The casement can be extended by placing a new part on top of the existing
          casement. Study the picture and answer the questions that follow.

                                                                           A

                                             FIGURE 3.4

          3.4.1       Name the omitted part that can be placed on top of the casement
                      to make it a complete casement.                                             (1)

          3.4.2       Name ONE purpose of the part that can be placed on top of the
                      casement.                                                                   (1)

          3.4.3       Identify member A.                                                          (1)

          3.4.4       Draw a neat freehand sketch of the sectional view of the profile of
                      part A in your ANSWER BOOK.                                                 (3)

Copyright reserved                                                             Please turn over

### Page 8

Downloaded from hlayiso.com
Civil Technology: Woodworking                 8                                  DBE/2021
                                           SC/NSC

3.5       FIGURE 3.5 below shows a vertical section through a wall panel which was
          constructed incorrectly. The wall panelling stretches from the floor to the
          ceiling. Study the picture and answer the questions that follow.

                                           FIGURE 3.5

          3.5.1       Identify THREE mistakes that were made during the construction of
                      the wall panelling.                                                      (3)

          3.5.2       Draw, in your ANSWER BOOK, a neat sketch of a vertical
                      sectional view of ONE tongue and groove board used in the
                      construction of wall panelling.                                          (3)

Copyright reserved                                                          Please turn over

### Page 9

Downloaded from hlayiso.com
Civil Technology: Woodworking                    9                                     DBE/2021
                                              SC/NSC

3.6       FIGURE 3.6 below shows the floor plan of a building with a gable roof with
          corrugated roof sheeting as roof covering. Study the figure and answer the
          questions. Show ALL calculations.

                                                                         500

                                        Wall A
                                                                         5 000

                                         9 000                        200

                                               FIGURE 3.6

          Use the following specifications:

              The walls are 220 mm thick.
              The length of one ridge capping is 2 350 mm.
              The true length of a rafter is 2 900 mm.
              The corrugated roof sheeting projects 50 mm past the rafter.

          Use the dimension sheet on ANSWER SHEET 3.6 and calculate the following
          (all units must be shown in METRES):

          3.6.1       The total length of fascia boards needed for the building                      (4)

          3.6.2       The length of ONE corrugated roof sheet                                        (2)

          3.6.3       The number of ridge cappings needed                                            (3)
                                                                                                     [30]

Copyright reserved                                                                Please turn over

### Page 10

Downloaded from hlayiso.com
Civil Technology: Woodworking                10                                  DBE/2021
                                           SC/NSC

QUESTION 4:          ROOFS, CEILINGS, TOOLS, EQUIPMENT AND MATERIALS
                     (SPECIFIC)

Start this question on a NEW page.

4.1       FIGURE 4.1 below shows four machines. Study the pictures and answer the
          questions that follow.

                                A                                B

                                C                                D

                                           FIGURE 4.1

          4.1.1       Name this group of machines.                                             (1)

          4.1.2       Identify A.                                                              (1)

          4.1.3       Explain why it is necessary to wear safety goggles when operating
                      the router in B.                                                         (1)

          4.1.4       Explain TWO reasons why it is necessary to check the timber for
                      loose knots and nails before using the electric planer in C.             (2)

          4.1.5       Explain how you would ensure an absolute straight cutting edge
                      when using a jig saw, as indicated in D.                                 (1)

          4.1.6       Explain what needs to be done with the work piece before you can
                      start cutting a circle from the centre of timber with a jig saw.         (1)

          4.1.7       What should you do with the work piece before you can start
                      working with a jig saw?                                                  (1)

Copyright reserved                                                          Please turn over

### Page 11

Downloaded from hlayiso.com
Civil Technology: Woodworking                  11                                  DBE/2021
                                             SC/NSC

4.2       The spindle moulder, like all other machines must be maintained, lubricated
          and serviced regularly. Describe any other TWO aspects to take care of for
          this machine.                                                                          (2)

4.3       Which part of the belt sander must be replaced after extensive use?                    (1)

4.4       Choose a description from COLUMN B that matches an item in COLUMN A.
          Write only the letter (A–L) next to the question numbers (4.4.1 to 4.4.8) in the
          ANSWER BOOK, e.g. 4.4.9 M.

                        COLUMN A                               COLUMN B
          4.4.1      Linseed oil                   A   marked according to the size of
                                                       the defects
          4.4.2      Factor for the selection of
                     timber for skirting           B   the grain pattern of the wood

          4.4.3      Visual grading                C   must be applied before varnish to
                                                       ensure the best finish
          4.4.4      Wax
                                                   D   should have a groove at the back
          4.4.5      Factor for the selection of
                     timber for folding table      E   provide a durable finish and
                                                       protect timber against wear and
          4.4.6      Sanding sealer                    tear

          4.4.7      Mechanical grading            F   a very long process and requires
                                                       repetition to ensure a durable
          4.4.8      Varnish                           surface finish

                                                   G   when the bending strength of
                                                       wood is tested

                                                   H   tends to develop white spots
                                                       where water has been spilled

                                                   I   causes shrinkage when applied

                                                   J   should be light in weight

                                                   K   brushes can be cleaned with
                                                       water

                                                   L   allow 10 minutes drying time
                                                       between layers
                                                                                       (8 x 1)   (8)

Copyright reserved                                                            Please turn over

### Page 12

Downloaded from hlayiso.com
Civil Technology: Woodworking                12                                     DBE/2021
                                           SC/NSC

4.5       Name TWO different types of trap doors that can be fitted in a ceiling.                 (2)

4.6       What are the minimum dimensions recommended for the opening of a trap
          door?                                                                                   (1)

4.7       Differentiate between purlins and battens according to their uses.                      (2)

4.8       ANSWER SHEET 4.8 shows the incomplete views of a South African (Howe)
          roof truss and a king post roof truss.

          4.8.1       Complete the drawings in good proportion to show the difference in
                      the construction of the respective roof trusses.                            (12)

          4.8.2       Label and dimension any TWO parts of the South African (Howe)
                      roof truss.                                                                 (4)
                                                                                                  [40]

Copyright reserved                                                             Please turn over

### Page 13

Downloaded from hlayiso.com
Civil Technology: Woodworking                13                                   DBE/2021
                                           SC/NSC

QUESTION 5:          CENTERING, FORMWORK, SHORING AND GRAPHICS                        AS
                     MEANS OF COMMUNICATION (SPECIFIC)

Start this question on a NEW page.

5.1       Draw, in good proportion, in your ANSWER BOOK a side view of the ribs and
          ties as used at the bottom of centering. Draw only ONE rib with the ties. Show
          ONE label with dimensions on the drawing.                                             (6)

5.2       ANSWER SHEET 5.2 shows a part of a timber prop for the formwork of a
          floor slab. Use ANSWER SHEET 5.2 and draw in good proportion a vertical
          section through the top part of the formwork for a floor slab. The end grain of
          the soffit board must be shown. Shows any THREE labels.                               (10)

5.3       Explain why the minimum distance between the wall and the dead shore
          should NOT be less than 1 200 mm.                                                     (1)

5.4       ANSWER SHEET 5.4 shows the incomplete sectional view of a dead shore
          for a multistorey building. Complete the drawing on ANSWER SHEET 5.4
          using a line diagram to draw the two dead shores and the needle just above
          the first floor slab.                                                                 (3)

5.5       Use ANSWER SHEET 5.5 and draw to scale 1 : 1 the top rail and stile of an
          assembled ISOMETRIC view of a long- and short-shoulder tenon and mortice
          joint. The timber used for the joint is 60 mm x 21 mm. Do NOT show hidden
          details.

          Start the drawing from the given corner on the ANSWER SHEET.                          (10)
                                                                                                [30]

Copyright reserved                                                           Please turn over

### Page 14

Downloaded from hlayiso.com
Civil Technology: Woodworking                  14                                    DBE/2021
                                             SC/NSC

QUESTION 6:          SUSPENDED FLOORS, STAIRCASES, IRONMONGERY, DOORS
                     AND JOINING (SPECIFIC)

Start this question on a NEW page

6.1       Various options are given as possible answers to the following questions.
          Choose the answer and write only the letter (A–D) next to the question
          numbers (6.1.1 to 6.1.5) in the ANSWER BOOK, e.g. 6.1.6 C.

          6.1.1       The minimum length of a tread/going is ...

                      A    250 mm.
                      B    200 mm.
                      C    300 mm.
                      D    350 mm.                                                               (1)

          6.1.2       The riser of a timber staircase ...

                      A    is the part on which you step when using the staircase.
                      B    is the vertical member between two consecutive treads.
                      C    secures the handrail to the balustrade.
                      D    must always be more than 200 mm.                                      (1)

          6.1.3       In a timber staircase the balustrade is …

                      A    at the foot of the staircase.
                      B    the vertical posts that hold up the handrail.
                      C    where the newel post joins the landing.
                      D    on top of the landing.                                                (1)

          6.1.4       The nosing of the staircase ...

                      A    is the overhang of the tread.
                      B    has a minimum length of 200 mm.
                      C    is between the newel posts.
                      D    is the vertical distance between two balusters.                       (1)

          6.1.5       A quarter-landing staircase is also called a/an ...

                      A    U-shaped staircase.
                      B    left-sided staircase of a half landing.
                      C    straight staircase with an intermediate landing.
                      D    L-shaped staircase.                                                   (1)

6.2       What is the minimum distance in a staircase between the pitch line and the
          ceiling?                                                                               (1)

Copyright reserved                                                            Please turn over

### Page 15

Downloaded from hlayiso.com
Civil Technology: Woodworking                  15                             DBE/2021
                                             SC/NSC

6.3       FIGURE 6.3 below shows THREE types of locks used in the building industry.
          Study the pictures and answer the questions that follow.

                                A                                B

                                                 C
                                             FIGURE 6.3

          6.3.1       Identify locks A to C respectively.                                   (3)

          6.3.2       Describe ONE advantage of B.                                          (1)

Copyright reserved                                                       Please turn over

### Page 16

Downloaded from hlayiso.com
Civil Technology: Woodworking                   16                             DBE/2021
                                              SC/NSC

6.4       FIGURE 6.4 below shows the inside elevation of a framed ledged and braced
          batten door with hinges. Study the drawing and answer the questions that
          follow.

                                                                  A

                                                                  B

                                                                  C

                                                                  D
                                                                  E

                                                                  F

                                              FIGURE 6.4

          6.4.1       Identify parts A to C respectively.                                    (3)

          6.4.2       Describe ONE the purpose of B.                                         (1)

          6.4.3       Name the thickness of rail D.                                          (1)

          6.4.4       Identify the joint used at E.                                          (1)

          6.4.5       Explain the reason why the bottom ends of the tongue and groove
                      boards run over the bottom rail of the door as indicated by F.         (1)

6.5       Draw in your ANSWER BOOK, in good proportion, a vertical section through
          the top rail and raised panel of a four-panel door with a low lock rail and
          diminishing stiles. Label the stile on your drawing.                               (5)

Copyright reserved                                                        Please turn over

### Page 17

Downloaded from hlayiso.com
Civil Technology: Woodworking               17                                    DBE/2021
                                          SC/NSC

6.6       Which items can be joined by using the following joining methods?

          6.6.1       Gang nails                                                             (1)

          6.6.2       Roofing nails                                                          (1)

          6.6.3       Storm clips                                                            (1)

6.7       Draw in your ANSWER BOOK, in good proportion, the front elevation of an
          assembled view of a twin/double mortice and tenon joint to show a part of the
          rail, stile and the hidden detail of the twin/double tenons.                       (6)

6.8       State the purpose of an ant guard as used in suspended timber floors.              (1)

6.9       FIGURE 6.9 below shows a part of the top view of a suspended timber floor.

                                                                                  A

                                                                                  B

                                                                                  C

                                                                                  D

                                          FIGURE 6.9

          6.9.1       Identify A–D.                                                          (4)

          6.9.2       Draw on ANSWER SHEET 6.9.2 where the detail of the suspended
                      floor in FIGURE 6.9 has been omitted, FOUR tongue and groove
                      floorboards. The tongue and groove boards must run in length
                      parallel to the long wall. NO hidden details are required.             (4)
                                                                                             [40]

                                                                              TOTAL:         200

Copyright reserved

### Page 18

Downloaded from hlayiso.com
Civil Technology: Woodworking                                  DBE/2021
                                             SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 2

NO.                   QUESTION                        ANSWER        MARKS
1.     Identify the type of plan in FIGURE 2.                             1

       Deduce from the notes the brick force
2.                                                                        1
       installation up to window height.

       Deduce the scale that is used for
3.                                                                        1
       FIGURE 2.
4.     Identify number 1.                                                 1

5.     Identify number 3.                                                 1

6.     Identify number 5.                                                 1

7.     Identify number 7.                                                 1

8.     Identify number 8.                                                 1

9.     Identify number 9.                                                 1
       Name the item in the column for the
10.    notes in FIGURE 2 that must be                                     1
       installed in the bathroom.

       Draw the electrical symbol as
11.    described in the column for the notes                              2
       in FIGURE 2

       Deduce from FIGURE 2 which
12.                                                                       1
       company printed the building plan.
13.    Give the abbreviation for number 2.                                1
       State the colour that you would use to
14.    indicate the new dwelling on the site                              1
       plan.
       Deduce from FIGURE 2 why the new
15.                                                                       1
       dwelling is to be built on a corner plot.

       Deduce the plot number of the new
16.                                                                       1
       dwelling illustrated in FIGURE 2.

       Which elevation is the closest to
17.                                                                       1
       Protea Street?

Copyright reserved

### Page 19

Downloaded from hlayiso.com
Civil Technology: Woodworking                              DBE/2021
                                               SC/NSC

       What is the plot number of the property
18.                                                                   1
       on the western side of the dwelling?
19.    Give the abbreviation for number 6.                            1
       State the slope at which the main                              1
20.
       sewer line should be installed.

21.    Describe what was done as revision 1.                          1

22.    Deduce the dimension fault on the total
                                                                      1
       width of the dwelling.
23.    State the project number for this plan.                        1

24.    What is the width of the pavement?                             1

25.    How many branch pipes are indicated
                                                                      1
       on the plan?

26.    Explain the purpose of number 4.                               1

       In what SI unit are the dimensions
27.    indicated on the plan?                                         1

       Draw a neat freehand drawing of the
       top view of the symbol of a single
28.    kitchen sink, as indicated in the                              3
       SANS/SABS Code of Practice for
       Building Drawings.
       Recommend TWO types of building
29.    materials that can be used to finish the                       2
       area at number 7.
       Calculate the total area of the plot.
30.    Give your answer in m².                                        3
       Show ALL calculations.

       Calculate the distance between
       Number 1 and Number 3 on the north
31.                                                                   4
       elevation.
       Show ALL calculations.

                                                        TOTAL:        40

Copyright reserved

### Page 20

Downloaded from hlayiso.com
Civil Technology: Woodworking                      DBE/2021
                                    SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 3.6

             A           B      C            D
3.6.1

3.6.2

3.6.3

Copyright reserved

### Page 21

Downloaded from hlayiso.com
Civil Technology: Woodworking                                                DBE/2021
                                           SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 4.8

SA (HOWE) ROOF TRUSS

                                  ASSESSMENT CRITERIA             MARK   CANDIDATE'S
                                                                            MARK
                                Correctness of drawing             9
                                Any TWO labels and dimensions      4
                                                       TOTAL:      13

KING POST ROOF TRUSS

                                  ASSESSMENT CRITERIA             MARK   CANDIDATE'S
                                                                            MARK
                                Correctness of drawing             3
                                                         TOTAL:    3

Copyright reserved

### Page 22

Downloaded from hlayiso.com
Civil Technology: Woodworking                                             DBE/2021
                                         SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 5.2

                                                              PROP

                                 ASSESSMENT CRITERIA          MARK   CANDIDATE'S
                                                                        MARK
                                Correctness of drawing         7
                                Any THREE labels               3
                                                     TOTAL:    10

Copyright reserved

### Page 23

Downloaded from hlayiso.com
Civil Technology: Woodworking                                   DBE/2021
                                         SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 5.4

        ASSESSMENT CRITERIA              MARK     CANDIDATE'S
                                                     MARK
   Correctness of drawing                 3
                                TOTAL:    3

Copyright reserved

### Page 24

Downloaded from hlayiso.com
Civil Technology: Woodworking                                              DBE/2021
                                        SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 5.5

                                  ASSESSMENT CRITERIA             MARK   CANDIDATE'S
                                                                            MARK
                                Correctness of drawing             10
                                                         TOTAL:    10

Copyright reserved

### Page 25

Downloaded from hlayiso.com
Civil Technology: Woodworking                                     DBE/2021
                                           SC/NSC

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET 6.9.2

            ASSESSMENT CRITERIA             MARK    CANDIDATE'S
                                                       MARK
         Correctness of drawing               4
                                  TOTAL:      4

Copyright reserved

## Related documents

- [Civil Technology May June 2021 (Woodworking) Afr](https://www.hlayiso.com/library/civil-technology-may-june-2021-woodworking-afr/ff7a7835-2450-4747-baaf-85c46ef7d411) — Civil Technology · QP · 2021 · Afr
- [CIV TECH GR12 QP SEPT2021 Afrikaans Construction](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2021-afrikaans-construction/19e5865a-d8a9-4741-b562-b0158255fd68) — Civil Technology · QP · 2021 · Afr
- [CIV TECH GR12 QP SEPT2021 English Construction](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2021-english-construction/551ab3e9-47c5-4ab0-a0cf-bc66dda5a956) — Civil Technology · QP · 2021 · Eng
- [Civil Technology May June 2021 (Civil Services) Eng](https://www.hlayiso.com/library/civil-technology-may-june-2021-civil-services-eng/dcb7f976-b3d6-42a9-b2b1-44ae9b2d8e3f) — Civil Technology · QP · 2021 · Eng
- [Civil Technology Nov 2021 (Construction) Eng](https://www.hlayiso.com/library/civil-technology-nov-2021-construction-eng/f39d7571-db9f-4ded-b5e7-27008235ca8b) — Civil Technology · QP · 2021 · Eng
- [Civil Technology May June 2022 (Woodworking) Eng](https://www.hlayiso.com/library/civil-technology-may-june-2022-woodworking-eng/6bfe9199-25cf-4c12-8dc6-817a01e3c184) — Civil Technology · QP · 2022 · Eng

## More from Grade 12 Civil Technology

- [Civil Technology (Woodworking) (Afrikaans) June 2025 Possible Answers](https://www.hlayiso.com/library/civil-technology-woodworking-afrikaans-june-2025-possible-answers/c0a65d19-28ca-4ac3-8c61-d4627d2a3133) — Memo · 2025 · Afr
- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-afrikaans/162bcc65-80ad-4384-b293-36da22468b06) — Memo · 2024 · Afr
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
