# Civil Technology Grade 12 NSC November 2020 QP (Eng)

> Grade 12 Civil Technology question paper from the NSC November Exam 2020 (English), 22 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/civil-technology-nov-2020-woodworking-eng/f45b898c-a9ab-4069-ae4b-2b730f88cf1b
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2020
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 22

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 NSC November 2020 QP (Eng)](https://www.hlayiso.com/library/civil-technology-nov-2020-woodworking-eng/f45b898c-a9ab-4069-ae4b-2b730f88cf1b)

## About this document

Civil Technology · Grade 12 · NSC November Exam · 2020. Question paper, 22 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayi fal

“= Ze basic education
An Department:

( () h Basic Education

QZ REPUBLIC OF SOUTH AFRICA

SENIOR CERTIFICATE/
NATIONAL SENIOR CERTIFICATE

GRADE 12

oo CIVIL TECHNOLOGY: WOODWORKING
" NOVEMBER 2020 “
METTTITTTTTTTTrrrrrerr Tree rrr eee eer errr rrr
MARKS: 200
TIME: 3 hours

This question paper consists of 14 pages and 7 answer sheets.

Copyright reserved Please turn over

### Page 2

Downloaded from hlayiso.com

Civil Technology: Woodworking 2 DBE/November 2020
SC/NSC

REQUIREMENTS:

1. Drawing instruments
2. A non-programmable calculator
3. ANSWER BOOK

INSTRUCTIONS AND INFORMATION
1. This question paper consists of SIX questions.
Answer ALL the questions.

Read all questions carefully.

k oO ON

Answer each question as a whole. Do NOT separate subsections of
questions.

a

Number the answers correctly according to the numbering system used in this
question paper.

Start the answer to EACH question on a NEW page.
Do NOT write in the margins of the ANSWER BOOK.

You may use sketches to illustrate your answers.

oo ND

Write ALL calculations and answers in the ANSWER BOOK or on the
attached ANSWER SHEETS.

10. Use the mark allocation as a guide to the length of your answers.

11. Make drawings and sketches in pencil, fully dimensioned and neatly finished
off with descriptive titles and notes to conform to the SANS/SABS Code of
Practice for Building Drawings.

12. For the purpose of this question paper, the size of a brick should be taken as
220 mm x 110 mm x 75 mm.

13. Use your own discretion where dimensions and/or details have been omitted.

14. Answer QUESTIONS 2, 3.3, 3.4, 3.5, 4.11, 5.6 and 6.9 on the attached
ANSWER SHEETS using drawing instruments, where necessary.

15. Write your CENTRE NUMBER and EXAMINATION NUMBER on every
ANSWER SHEET and hand them in with your ANSWER BOOK, whether you
have used them or not.

16. Drawings in the question paper are NOT to scale due to electronic transfer.
17. Google Images was used as the source of all photographs and pictures.

18. Write neatly and legibly.

Copyright reserved Please turn over

### Page 3

Downloaded from hlayiso.com

Civil Technology: Woodworking 3

SC/NSC

DBE/November 2020

QUESTION 1: OHSA, SAFETY, MATERIALS, TOOLS, EQUIPMENT AND JOINING

(GENERIC)

Start this question on a NEW page.

1.1

Choose a description from COLUMN B that matches an item in COLUMN A.
Write only the letter (A-K) next to the question numbers (1.1.1 to 1.1.8) in the

ANSWER BOOK, e.g. 1.1.9 L.

COLUMN A

COLUMN B

1.1.1. Powder coating
1.1.2 | Rungs

1.1.3. Wing nut

1.1.4 Rawl bolts

1.1.5 Telescopic staff
1.1.6 Accident

1.1.7 Putlog scaffold

1.1.8 Building rubble

must be inclined slightly towards a
building

is used with the dumpy level to
measure heights accurately

allows a worker to climb up or down a
ladder

can be tightened or loosened without
using a spanner

suitable for outdoor furniture

result of an unsafe act or unsafe
condition

must not be placed where it may
obstruct the access to or the exit from
a building site

resists pull-out failure

must be secured firmly when there is
any sagging

prevent(s) workers from falling off a
scaffold

disposal of waste materials and
debris

(8 x 1)
1.2 Explain ONE advantage of galvanising.
1.3 Name the document on hazardous chemical substances which the OHS Act
requires employers to provide to interested or affected persons.
1.4 Describe TWO methods that can be used to move building material around

the site.

Copyright reserved

Please turn over

(8)
(1)

(1)

### Page 4

Downloaded from hlayiso.com

Civil Technology: Woodworking 4 DBE/November 2020

SC/NSC

1.5 State TWO specific advantages of water-based paint.

1.6 You were tasked to locate steel bars and copper pipes placed into a wall.
1.6.1 Name the tool you would use to detect these materials.
1.6.2 Describe how you would take care of this tool after using it.
1.7 FIGURE 1.7 below shows a joining fixture that is commonly used.

ae
at

FIGURE 1.7

Explain how this joining fixture can be used to secure a bracket to a wall.

QUESTION 2: GRAPHICS AS MEANS OF COMMUNICATION (GENERIC)

Start this question on a NEW page.

FIGURE 2 on the next page shows different drawings that appear on a building pian.

Analyse the drawings and complete the table on ANSWER SHEET 2.

Copyright reserved

Please turn over

(2)

(1)
(2)

(3)
[20}

### Page 5

Downloaded from hlayiso.com

Civil Technology: Woodworking

5
SC/NSC

DBE/November 2020

NOTES:

Contractors must verify all
dimensions and levels on site before
commencing work. Architects must
be notified of any discrepancies
immediately.

ARCHITECT'S SIGNATURE
CLIENT'S SIGNATURE

Brick force must be installed every
third course up to window height.
From the top of the window, brick
force must be installed between
every course up to wall plate height.

DPM must be fitted under the floor
slab to prevent water from
penetrating from the substructure.

The following electrical fittings must
be installed in the kitchen:

OD)

FIGURE A exe
SCALE 1: 100 REVISION DATE | DESCRIPTION
PRINTED BY: DATE OF PRINT:
4—— 2500 fo 2.000 1100} MTANDO PRINTERS 01/04/2020
§) 220 py wi oe woe § DRAWING TITLE:
4 1 4 SITE PLAN STAND 101
_™ — — -
BATHROOM PROJECT:
BEDROOM 1 PROPOSED DWELLING ON STAND 101,
| 3 JABULANI STREET, CRADOCK
a
ca) |
5 | PROJECT NO. DRAWING NO.
° = | cRa48-210 559P7
c=}
] = 8 DATE _|DRAWN | CHECKED |SCALE
fo + 27/03/2020 | N DAMON] P HENSLO | 1 : 100
L
2 REFERENCE CODE
| ® =i QP 4.2020
-|| a
WINDOW 1 WINDOW 2
S| 1x40W LOUNGE 8
KITCHEN
|
i 1600
_—SY 600
wi 2 g} |S “ g| |"
< Z N “Us
FIGURE B / \
SCALE 1 : 100
FIGURE 2 [40]

Copyright reserved

Please turn over

### Page 6

Downloaded from hlayiso.com

Civil Technology: Woodworking 6 DBE/November 2020
SC/NSC

QUESTION 3: CASEMENTS, CUPBOARDS, WALL-PANELLING AND
QUANTITIES (SPECIFIC)

Start this question on a NEW page.

3.1 Give ONE word/term for each of the following descriptions by choosing

a word/term from the list below. Write only the word/term next to the question
numbers (3.1.1 to 3.1.5) in the ANSWER BOOK, e.g. 3.1.6 skirting.

cornice; quadrant; window sill; mullion; glazing bar; front rail;
mortice and tenon; tongue and groove; putty; panel pins;
glue; PVC; capping; paint; top rail; varnish

3.1.1 The moulding between the skirting and the floor (1)
3.1.2 The member that separates the main parts of a double casement
vertically (1)
3.1.3 Used to keep the window pane in place (1)
3.1.4 The joint used to join the strip boards used in wall panels (1)
3.1.5 Horizontal member of the casement that is found directly below the
transom (1)

3.2 Use your ANSWER BOOK and draw in good proportion a neat vertical section
through the transom of a casement frame with a fanlight. (4)

3.3 Use ANSWER SHEET 3.3 and draw to scale 1 : 10 the front view of a
freestanding kitchen cupboard with two doors. The left-hand bottom of the
cupboard must start at A on the ANSWER SHEET.

Use the following specifications:

e ~=Height: 950 mm

« Width: 900 mm

e 16mm melamine board is used for the construction of the cupboard

e Doors: 450 mm wide

Use the assessment criteria on the ANSWER SHEET as a guide. (9)

3.4 FIGURE 3.4 on ANSWER SHEET 3.4 shows a horizontal section through a
part of a wall. Use ANSWER SHEET 3.4 and draw in good proportion a neat
horizontal sectional view of the bottom part of a wall panel showing how the
strip boards are joined.

Use the assessment criteria on the ANSWER SHEET as a guide. (4)

Copyright reserved Please turn over

### Page 7

Downloaded from hlayiso.com

Civil Technology: Woodworking 7 DBE/November 2020
SC/NSC

3.5 FIGURE 3.5 below shows the floor plan of a garage with a hipped roof. The
width of the walls is 220 mm. Study the figure and answer the questions that
follow. Show ALL calculations.

230, 12 000
So
So
Qo
o
=
“
N
FIGURE 3.5
Use ANSWER SHEET 3.5 and calculate the following:
3.5.1 The length of fascia board needed for the roof (4)
3.5.2 The length of skirting needed for the garage (4)

[30]

Copyright reserved Please turn over

### Page 8

Civil Technology: Woodworking 8 DBE/November 2020

Downloaded from hlayiso.com

SC/NSC

QUESTION 4: ROOFS, CEILINGS, TOOLS AND EQUIPMENT, AND MATERIALS

(SPECIFIC)

Start this question on a NEW page.

4.1

4.2

Copyright reserved

FIGURE 4.1 below shows an electrical hand tool. Study the picture and
answer the questions that follow.

FIGURE 4.1
4.1.1 Identify the tool.

4.1.2 Describe what can happen if no personal safety equipment is worn

while operating this hand tool.

4.1.3 Why should this hand tool be stored in a safe, dry place?

FIGURE 4.2 below shows a thickness planer. Study the picture and answer

the questions that follow.

FIGURE 4.2

4.2.1 Explain what would happen if you adjusted the height of the table

while the machine is in operation.

4.2.2 Explain what care must be taken to maximise the use of the blades

of the machine.

Please turn over

(1)

(2)
(1)

(2)

(2)

### Page 9

Downloaded from hlayiso.com

Civil Technology: Woodworking 9 DBE/November 2020
SC/NSC
4.3 Name the different types of roof underlays for EACH of the following roofs:

44

4.5

4.6

47

4.8

4.9

4.10

4.11

4.3.1 Tiled roofs
4.3.2 Thatch roofs
4.3.3 IBR roof sheeting

Draw in your ANSWER BOOK a top view of a roof to show the valley between
two inclined roofs.

Give ONE reason why you would close an open eave.

Explain why you would rather use fibre-cement ceiling board on closed eaves
than gypsum ceiling board.

Describe TWO disadvantages of EACH of the following roof coverings:
4.7.1 Concrete roof tiles

4.7.2 Thatch roofs

4.7.3 Corrugated iron sheeting

Name TWO parts of the roof construction onto which the framework of a
trapdoor will be secured.

Explain why you would rather use mechanically graded timber than visually
graded timber for roof construction.

Give TWO reasons why timber must be preserved.

Use ANSWER SHEET 4.11 and draw to scale 1 : 50 a king post roof truss.
Start the drawing on the lines indicated on the ANSWER SHEET.

Use the assessment criteria on the ANSWER SHEET as a guide.

Copyright reserved Please turn over

(1)
(1)
(1)

(3)
(1)

(1)

(2)

(2)
(2)

(2)
(2)

(12)
[40]

### Page 10

Downloaded from hlayiso.com

Civil Technology: Woodworking 10 DBE/November 2020
SC/NSC

QUESTION 5: CENTRING, FORMWORK, SHORING AND GRAPHICS AS MEANS
OF COMMUNICATION (SPECIFIC)

Start this question on a NEW page.

5.1 FIGURE 5.1 below shows the construction detail at the foot of a centre.
Identify parts A to E.

So

MIA

Zi

FIGURE 5.1 (5)

5.2 Justify the use of an adjustable steel prop rather than a wooden prop when
installing formwork. (1)

5.3 FIGURE 5.3 below shows part of the detail of a dead shore. Study the
drawing and answer the questions that follow.

FIGURE 5.3

Copyright reserved Please turn over

### Page 11

Downloaded from hlayiso.com

Civil Technology: Woodworking 11 DBE/November 2020
SC/NSC
5.3.1 Name ONE type of shoring other than dead shoring. (1)
5.3.2 Explain the use of A. (1)
5.3.3 Describe the purpose of B. (1)
5.4 FIGURE 5.4 below shows a dead shore that was constructed incorrectly.

5.5

5.6

Redraw the table below into your ANSWER BOOK and identify TWO possible
mistakes in the construction of the dead shore AND recommend possible
solutions to rectify the mistakes.

NO. MISTAKES IN THE POSSIBLE SOLUTIONS TO
CONSTRUCTION OF THE RECTIFY THE MISTAKES
DEAD SHORE
1 |
2
a —T

Piksas tira tre

VA

FIGURE 5.4 (4)

Differentiate, by means of TWO line diagrams, between a couple roof truss
and a collar-tie roof truss in your ANSWER BOOK. Show the walls as part of
your answer. (8)

FIGURE 5.6 on ANSWER SHEET 5.6 show two walls that must support an
in-situ cast concrete floor. Use ANSWER SHEET 5.6 and draw in good
proportion a vertical section through the formwork for an in-situ cast concrete
floor. Show the support for the formwork on one side of a supporting wall.

Use the assessment criteria on the ANSWER SHEET as a guide. (9)
[30]

Copyright reserved Please turn over

### Page 12

Downloaded from hlayiso.com

Civil Technology: Woodworking 12

SC/NSC

DBE/November 2020

QUESTION 6: SUSPENDED FLOORS, STAIRCASES, IRONMONGERY, DOORS
AND JOINING (SPECIFIC)

Start this question on a NEW page

6.1 Various options are given as possible answers to the following questions.
Choose the answer and write only the letter (A-D) next to the question

numbers (6.1.1 to 6.1.5) in the ANSWER BOOK, e.g. 6.1.6 E.

6.1.1

6.1.2

6.1.4

Copyright reserved

The walls of a substructure can be ...

A
B
Cc
D

any width.

330 mm or 220 mm wide.
220 mm or 110 mm wide.
None of the above-mentioned

The minimum measurement of a tread for stairs is ...

A
B
c
D

250 mm.
750 mm.
150 mm.
350 mm.

The ... is the member that is fixed onto a door frame and into which
the latch and bolt of a lock fit.

A

B
c
D

diagonal plate

stop plate

keeper

back plate/striker plate

The vertical member between two panels of a door is called a ...

A
B
Cc
D

lock rail.
transom.
muntin.
middle rail.

A door can be attached to a door frame by using various types
of ...

vuaoaD

screws.
nails.

clamps.
hinges.

Please turn over

(1)

(1)

(1)

(1)

(1)

### Page 13

Downloaded from hlayiso.com

Civil Technology: Woodworking 13 DBE/November 2020
SC/NSC

6.2 FIGURE 6.2 below shows part of the floor plan of a suspended timber floor.
Study the drawing and name parts A to D.

=
= A
|_| op | p=
ay
= df db D
“yf +
FIGURE 6.2 (4)

6.3 Justify why the concrete base under part C in FIGURE 6.2 should be wider
than part C. (1)

6.4 Draw in your ANSWER BOOK, in good proportion, the top view of part of the
layout of the upper level of the suspended floor to show how the struts are

staggered. (3)
6.5 Explain why ant guards used for suspended timber floors must be made from
galvanised steel. (1)

6.6 Distinguish between cut cupboard locks and drawer/till locks regarding the
direction of the bolts of the locks when locking. (2)

6.7 Draw in your ANSWER BOOK, in good proportion, a vertical section through
a lock rail and part of the raised panels of a three-panel door. (6)

Copyright reserved Please turn over

### Page 14

Downloaded from hlayiso.com

Civil Technology: Woodworking 14 DBE/November 2020
SC/NSC
6.8 FIGURE 6.8 below shows the assembled view of a haunched mortice and

6.9

6.10

tenon joint. Study the drawing and name parts A to D.

FIGURE 6.8 (4)

FIGURE 6.9 on ANSWER SHEET 6.9 shows the bottom half of the internal
elevation of a framed ledged and braced batten door.

Use ANSWER SHEET 6.9 and draw the following:

6.9.1 The brace (1)
6.9.2 The sectional view of section A-A. Draw the sectional view two
times bigger than the given view. (5)

Use the assessment criteria on the ANSWER SHEET as a guide.

Draw in your ANSWER BOOK a line diagram of the top view of a straight
flight of stairs with a landing between the steps.

Show the following on your drawing:

« 110mm wall

* Three treads on both sides of the landing

e« Landing

« Handrail

e¢ Two newel posts

e Arrows indicating the rise of the stairs (8)

[40]

TOTAL: 200

Copyright reserved

### Page 15

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC
| CENTRE NUMBER: | | |
| EXAMINATIONNUMBER: | | | | | L | LT]

ANSWER SHEET 2

No. QUESTION ANSWER MARKS

1 Identify the elevation in FIGURE A. 1

2 Describe the type of house that is 1
indicated in FIGURE A.

3 Identify number 1. 1

4 Identify number 3. 1

5 Identify number 4. 1

6 Identify the fastener indicated by 1
number 5.

7 Identify number 6. 1

8 Identify number 7. 1

9 Identify number 8. 41

10 What does DPM stand for, as 1
indicated in the notes?

11 Identify number 10. 1
Recommend a suitable material that

12 can be used for the manufacturing of 1
number 2 in FIGURE A.

13 Name the TWO elevations on which 2
number 2 is installed.

14 Describe the purpose of number 3. 1
Deduce ONE feature that has been

15 omitted from the elevation in 1
FIGURE A.
Recommend any TWO sanitary

16 fitments carrying waste-water, other 2
than a bath, that can be installed in
the room indicated by number 11.

Copyright reserved

### Page 16

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC

What sanitary fixture carrying soil
17 water can be installed in the room
indicated by number 12?

Describe the error that appears at
18 number 6 in the elevation in
FIGURE A.

19 State the reference code for this plan.

20 Which room will number 13 serve?

1 What does the line between
numbers 13 and 14 represent?

Differentiate between number 15 in
22 FIGURE B and number 17 in the
notes.

Explain the installation of brick force
23 from the top of the window to the wall
plate, as indicated by the architect.

24 Recommend a possible finish for the
outside walls of the house.

Deduce from FIGURE 2 which

25 elevation does NOT have windows.

26 Deduce the thickness of the external
wall from FIGURE 2.

27 Name a material that can be used to
close the open sides of number 16.

28 Name the town in which the proposed
dwelling will be build.

Calculate the area of the bathroom.
29 Show ALL calculations. Give your
answer in m?.

Calculate the total length of the wall
30 on the eastern side of the building.
Show ALL calculations. The length
must be indicated in metres.

TOTAL:

Copyright reserved

### Page 17

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC

[ CENTRE NUMBER: [LT 7 J

[EXAMINATIONNUMBER: | | | | | | | | | || 4 [J

ANSWER SHEET 3.3

AL

ASSESSMENT CRITERIA MARK | CANDIDATE'S
MARK

Kick plate

Sides

Top rail

Bottom shelf

Top 32 mm thick

_Top overhang 30 mm on either side
Middle shelf

Doors

Correctness of drawing

wp o)o)o)s{s)/3)/) i)

TOTAL: (9)

Copyright reserved

### Page 18

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020

SC/NSC

| CENTRE NUMBER: [TTT TTT {i

[EXAMINATIONNUMBER: | | | | | | | | | | (| L]

ANSWER SHEET 3.4

ASSESSMENT CRITERIA MARK | CANDIDATE'S
MARK

Rough ground
Strip boards
Skirting

plalrno/a

TOTAL:

(4)

Copyright reserved

### Page 19

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC
| CENTRE NUMBER: LT TTT TT yl
[EXAMINATIONNUMBER: | | | | | | | | | | | | | /|
ANSWER SHEET 3.5
A B c D
(8)

Copyright reserved

### Page 20

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC

| CENTRE NUMBER: LTT TT] [Tl

[EXAMINATIONNUMBER: | | | | | | | | | | [| [| J |

ANSWER SHEET 4.11
ASSESSMENT CRITERIA MARK CANDIDATE'S
MARK

220 mm walls with inside span of 4 000 mm 2

Wall plates 114 x 38 mm 2

Tie beam 114 x 38 mm 4

Rafters 114 x 38 mm 2

King post_114 x 38 mm 4

Correctness of drawing 1

Application of scale:

ONE or TWO incorrect =3

THREE or FOUR incorrect =2 3

More than FIVE incorrect =1

NO measurements correct =0

TOTAL: 12 (12)

Copyright reserved

### Page 21

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC

[CENTRE NUMBER: ETT tT tT tT ft Tt

[EXAMINATIONNUMBER: | | | | | | | | | [| | [| J

ANSWER SHEET 5.6

KL my

ASSESSMENT CRITERIA MARK | CANDIDATE'S
MARK

Soffit/Shutter board
Bearer

Cross bearer

Prop

Folding wedges
Soleplate

Any TWO labels
Correctness of drawing

wlalr|o)a)a)s|o} a

TOTAL:

Copyright reserved

### Page 22

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2020
SC/NSC
[CENTRENUMBER: | | | | 1
[EXAMINATIONNUMBER: | | | | | | | [ | | | J] J |
ANSWER SHEET 6.9
6.9.1
1 if ! 1
I 1 Ly 1
1 1 ' ! '
i L ! i 1
6.9.2

A

A:
>|
6.9.1 FIGURE 6.9
ASSESSMENT CRITERIA MARK CANDIDATE'S
MARK
Brace 1
TOTAL:
6.9.2
ASSESSMENT CRITERIA MARK CANDIDATE'S
MARK
V tongue and groove batten 1
Brace 1
Bottom rail 4
Hatching 1
Arrow indicating the style 4
TOTAL: 5

Copyright reserved

(1)

(5)

## Related documents

- [Civil Technology Nov 2020 (Civil Services) Afr](https://www.hlayiso.com/library/civil-technology-nov-2020-civil-services-afr/b796705a-6588-4c35-a6ed-9d9659bce995) — Civil Technology · QP · 2020 · Afr
- [Civil Technology Nov 2020 (Construction) Eng](https://www.hlayiso.com/library/civil-technology-nov-2020-construction-eng/6e24138d-3f1b-42f9-8076-7ae0b7db457a) — Civil Technology · QP · 2020 · Eng
- [Civil Technology Nov 2020 (Civil Services) Eng](https://www.hlayiso.com/library/civil-technology-nov-2020-civil-services-eng/8ecb8551-97e5-4a57-8187-0130f8d158da) — Civil Technology · QP · 2020 · Eng
- [Civil Technology Nov 2020 (Construction) Afr](https://www.hlayiso.com/library/civil-technology-nov-2020-construction-afr/7e3d3218-d564-4a19-b535-b7ed8a417256) — Civil Technology · QP · 2020 · Afr
- [Civil Technology Nov 2020 (Construction) Memo Eng](https://www.hlayiso.com/library/civil-technology-nov-2020-construction-memo-eng/f06cef7f-235e-45f7-9f9b-f8e6a2b0c0ca) — Civil Technology · Memo · 2020 · Eng
- [Civil Technology Nov 2020 (Civil Services) Memo Afr](https://www.hlayiso.com/library/civil-technology-nov-2020-civil-services-memo-afr/8cffc125-69c0-44e9-b0eb-88ae7e930363) — Civil Technology · Memo · 2020 · Afr

## More from Grade 12 Civil Technology

- [Civil Technology (Woodworking) (Afrikaans) June 2025 Possible Answers](https://www.hlayiso.com/library/civil-technology-woodworking-afrikaans-june-2025-possible-answers/c0a65d19-28ca-4ac3-8c61-d4627d2a3133) — Memo · 2025 · Afr
- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-afrikaans/162bcc65-80ad-4384-b293-36da22468b06) — Memo · 2024 · Afr
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
