# Civil Technology Grade 12 NSC November 2023 QP (Eng)

> Grade 12 Civil Technology question paper from the NSC November Exam 2023 (English), 26 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/civil-technology-nov-2023-woodworking-eng/fdfc3cf4-1a3a-4817-a3e9-a2c7f9fe5c2e
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2023
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 26

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 NSC November 2023 QP (Eng)](https://www.hlayiso.com/library/civil-technology-nov-2023-woodworking-eng/fdfc3cf4-1a3a-4817-a3e9-a2c7f9fe5c2e)

## About this document

Civil Technology · Grade 12 · NSC November Exam · 2023. Question paper, 26 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

— ——= —<—==—=

\ ay
=i basic education

SWE

ot Department:

‘GO Basic Education
a Ze

Sad REPUBLIC OF SOUTH AFRICA

NATIONAL
SENIOR CERTIFICATE

GRADE 12
F) CIVIL TECHNOLOGY: WOODWORKING fn
" NOVEMBER 2023 H

MARKS: 200

TIME: 3 hours

This question paper consists of 14 pages and 10 answer sheets.

Copyright reserved Please turn over

### Page 2

Downloaded from hlayiso.com

Civil Technology: Woodworking N 25 DBE/November 2023

REQUIREMENTS:

1. Drawing instruments

2. A non-programmable calculator

3. ANSWER BOOK

INSTRUCTIONS AND INFORMATION

1. This question paper consists of SIX questions.

2. Answer ALL the questions.

3. Read ALL the questions carefully.

4. Answer. each question as a whole. Do NOT separate subsections of
questions.

5. Number the answers correctly according to the numbering system used in this
question paper.

6. Start the answer to EACH question on a NEW page.

7. Do NOT write in the margins of the ANSWER BOOK.

8. You may use sketches to illustrate your answers.

9. Write ALL calculations and answers in the ANSWER BOOK or on the
attached ANSWER SHEETS.

10. Use the mark allocation as a guide to the length of your answers.

11. Make drawings and sketches in pencil, fully dimensioned and neatly finished
off with descriptive titles and notes to conform to the SANS/SABS Code of
Practice for Building Drawings.

12. For the purpose of this question paper, the size of a brick should be taken as
220 mm x 110 mm x 75 mm.

13. Use your own discretion where dimensions and/or details have been omitted.

14, Answer QUESTIONS 2, 3.2, 3.3, 3.4, 5.4, 5.5, 5.6, 6.3, 6.4 and 6.5 on the
attached ANSWER SHEETS using drawing instruments, where necessary.

15. Write your CENTRE NUMBER and EXAMINATION NUMBER on every
ANSWER SHEET and hand them in with your ANSWER BOOK, whether you
have used them or not.

16. Drawings in the question paper are NOT to scale due to electronic transfer.
17. Google Images was used as the source of all photographs and pictures.
18. Write neatly and legibly.

Copyright reserved Please turn over

### Page 3

Downloaded from hlayiso.com

Civil Technology: Woodworking 3 DBE/November 2023
NSC

QUESTION 1: OHSA, MATERIALS, TOOLS, EQUIPMENT AND JOINING
(GENERIC)

Start this question on a NEW page.

1.1 Various options are provided as possible answers to the following questions.
Choose the answer and write only the letter (A-D) next to the question
numbers (1.1.1 to 1.1.12) in the ANSWER BOOK, e.g. 1.1.13 D.

1.1.1 Electroplating is the process of ...

A applying a plastic coating on metal using electrolysis.
B coating a metal with another metal using electrolysis.
C applying paint to a metal by means of magnetism.

D applying liquid zinc to a metal using pressure.

1.1.2 The process of keeping freshly cast concrete damp will ...

A provide concrete with more volume.

B_ make concrete more watertight.

C_ increase the risk of cracking concrete.
D_ lead to poor bonding of concrete.

1.1.3 Why would you coat a metal with a layer of paint?

A To resist extreme temperatures
B_ To prevent corrosion

C_ To prevent warping

D Only AandB

1.1.4 The minimum size of a wooden scaffold plank:

A 300 mm wide x 60 mm thick
B 238 mm wide x 12 mm thick
C 150 mm wide x 20 mm thick
D 228 mm wide x 38 mm thick

1.1.5 When using a scaffold, it must be inspected to ensure that ...

the scaffold is not attached to the building.
the scaffold platform is supported every 4 m.
the scaffold is free from any defects.

All the above-mentioned

leeks =

1.16 ... of scaffolds should be secured vertically.

A Transoms

B_ Diagonal braces
C_ Standards

D_ Base plates

Copyright reserved Please turn over

(1)

(1)

(1)

(1)

(1)

(1)

### Page 4

Downloaded from hlayiso.com

Civil Technology: Woodworking

1.1.7

1.1.8

1.1.9

1.1.10

1.1.11

1.1.12

Copyright reserved

4
NSC
The guard rail on a scaffold will ensure that ...

A aworker does not fall from the scaffold.
B_ tools do not fall from the scaffold.

C_ the scaffold is stable.

D_ the scaffold is braced.

DBE/November 2023

Toe boards must be at least 150 mm high from the level of the ...

A scaffold platform.

B guard rail.

C_ horizontal transoms.
D base plate.

The employer must ensure that the rungs of wooden ladders are ...

A not painted.

B_ free from grease.

C not cracked.

D_ All the above-mentioned

The material safety data sheet for hazardous chemicals must have

the following information:

A Quantity in the container
B_ Cost of the chemicals ~
C_ Disposal considerations
D Manufacturing process

Stairways must be installed at a minimum of ... degrees from the

horizontal.

A 50
B30
c 40
D 60

The purpose of the builder's hoist is to transport ...

workers and materials.

materials and heavy construction machines.
equipment and heavy machines.

materials and furniture.

VQDY

Please turn over

(1)

(1)

(1)

(1)

(1)

(1)

### Page 5

Downloaded from hlayiso.com

Civil Technology: Woodworking 5 DBE/November 2023
NSC
1.2 You have been tasked by a contractor to install a 20 kg gate to the pier of a
boundary wall.
1.2.1 Name the joining fixture you will use to secure the gate to the pier. (1)
1.2.2 Motivate why you will use this joining fixture. (2)

1.2.3 Explain how you will install the gate by using the joining fixture in
QUESTION 1.2.1, if the positions of the holes have been marked

on the pier. (3)

1.3 Predict what will happen if a laser level is stored in extremely cold areas. (1)

1.4 How will you ensure the accuracy of a dumpy level? (1)
[20]

QUESTION 2: GRAPHICS AS MEANS OF COMMUNICATION (GENERIC)
Start this question on a NEW page.

FIGURE A and FIGURE B on the next page show drawings that appear on a building
plan. Analyse the drawings and complete the table on ANSWER SHEET 2.

Copyright reserved Please turn over

### Page 6

Downloaded from hlayiso.com

Civil Technology: Woodworking

DBE/November 2023

4

3.000

°

2 955
N

2 955

©

FFL

©

FIGURE A

| 600

NOTES:

Contractors must verify all
dimensions and levels on site
before commencing work.

Architects to be notified
of any discrepancies immediately.

Emergency escape staircase to be
made of mild steel.

Roof: Lean-to roof with parapet
walls

Finishing of walls: Plaster and paint

No. 3 indicates the balusters to be
made of aluminium.

Dimensions of balusters:
@ 50 mm x 1 200 mm

Architect's signature ....

Client's signature ...........-.....

000

3 340 y

220 |

110

BATHROOM

©—lIg

KITCHEN

w1

2x40
OFFICE

wi

si

poarDRoom ||

3

w1

x

J

4 500 | 1.500

3300 11 500

FIGURE B

®

DRAWING OF
INTERNAL
STAIRCASES

REVISION DATE:
1 48/04/2023

PRINTED BY:
FOX PRINTERS

DATE OF PRINT:
19/04/2023

DRAWING TITLE:
418" FLOOR AND SOUTH ELEVATION

PROJECT:
PROPOSED DWELLING OF MR NTOMBI
ON PLOT 42, ISIDINGO STREET, ALBANY

PROJECT NO.:
GR 266-424

DRAWING NO.:
336P5

DATE: DRAWN:
12/04/2023 NP KOK

CHECKED:
JBOK

ELEVATION AND
FLOOR PLAN

SCALE 1: 100

REFERENCE CODE
QP 8 — 2023

WINDOW SCHEDULE

1200

[40]

Copyright reserved

Please turn over

### Page 7

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023

7
NSC
QUESTION 3: CUPBOARDS, CASEMENTS, WALL-PANELLING AND

QUANTITIES (SPECIFIC)
Start this question on a.NEW page.

3.1. FIGURE 3.1 below shows the vertical sectional view of the transom for a
double casement window with a fanlight. Use the given information and
sketch ONLY the bottom rail of the fanlight in your ANSWER BOOK.

f[ X

FIGURE 3.1 (4)

3.2 FIGURE 3.2 below shows the floor plan of a storeroom with a gable roof.

30

ae
00

'
1
t
‘
'
'
'
1
1
1
1
1
1
i
1
5
f
'
t
'
'
'
4
1
1
1
1
i
1
1
'
'
1
'
t
'
'
'
'
'
'
1
1
1

FIGURE 3.2

Use the following specifications:

Type of roof: South African (Howe) roof truss

The roof has EIGHT South African (Howe) roof trusses.
The walls are 220 mm thick.

The true length of the king post is 870 mm.

Round off your answer to TWO decimals.

eeeee

Use the dimension paper on ANSWER SHEET 3.2 and calculate the

following:

3.2.1 The total length of wall plate needed for the building (5)
3.2.2 The total length of timber required for the king posts (3)
NOTE: A mark will be awarded for the correct use of the dimension paper. (1)

Copyright reserved Please turn over

### Page 8

Downloaded from hlayiso.com

Civil Technology: Woodworking 8 DBE/November 2023
NSC
3.3 ANSWER SHEET 3.3 shows the front view of a freestanding cupboard, with

3.4

an oval hanging rail and a drawer, without a door.

Project the detail of the freestanding cupboard and draw a sectional left view
on cutting plane A-A.

Use the following specifications:

« The cupboard is made of 16 mm melamine boards.
e The drawer bottom is made of 3 mm hardboard.
e The cupboard back is made of 3 mm hardboard.

Use ANSWER SHEET 3.4 and complete the drawing of the horizontal
sectional view of the wall panelling by drawing TWO tongue and groove
boards that are secured by means of secret nailing. Print the label of the
rough ground.

Copyright reserved Please turn over

(13)

(4)
[30]

### Page 9

Downloaded from hlayiso.com

Civil Technology: Woodworking 9 DBE/November 2023
NSC

QUESTION 4: ROOFS, CEILINGS, TOOLS, EQUIPMENT AND MATERIALS
(SPECIFIC)

Start this question on a NEW page.

4.1 Choose a description from COLUMN B that matches the item in COLUMN A.

Write only the letter (A-H) next to the question numbers (4.1.1 to 4.1.5) in the
ANSWER BOOK, e.g. 4.1.6 J.

COLUMN A COLUMN B
4.1.1 Thickness planer A drilling round holes of different
sizes
4.1.2 Lathe

B_ the blade has to be pulled through
4.1.3 Mortising machine the stock by means of a back
pressure action

4.1.4 Radial arm saw
C_ avoid working with timber that is
4.1.5 Band saw shorter than the distance between
the feeding rollers

D_ make sure that the splitter is in
position

E the chisel attachment can drill
square holes vertically into wood

F do not shape timber pieces shorter
than 250 mm

G_ remove the tool rest when sanding
or polishing

H_ the top blade guide must always
be adjusted to 6 mm above the
stock

(5 x 1)

Copyright reserved Please turn over

(5)

### Page 10

Downloaded from hlayiso.com

Civil Technology: Woodworking 10 DBE/November 2023
NSC
4.2 Change the underlined word(s) in the following to make the statements

TRUE. Write the appropriate word(s) next to the question numbers
(4.2.1 to 4.2.5) in the ANSWER BOOK.

4.2.1 When selecting timber for windows and doors, the line pattern must
be considered. (1)
4.2.2 The head of each graded timber board is marked in blue with the
SABS symbol. (1)
4.2.3 The length of truss members can be 114 mm. (1)
4.2.4 Store a belt sander in a wooden box away from sunshine. (1)
4.2.5 Use both hands to carry an electric plane. (1)
4.3 FIGURE 4.3 below shows an incomplete view of the constructional detail of
the framework for a trap door.
—- —A
te Beas
Hy abe
FIGURE 4.3
4.3.1 Explain the value of having a trap door in a building. (1)

4.3.2 What is the size of the timber that is commonly used for a trap door
construction, below the roof trusses? (1)

4.3.3 Draw, in your ANSWER BOOK, the detail of the framework for a
trap door opening between the two roof trusses as seen from

below. Print any ONE label. (5)
44 Explain how you will install the first corrugated iron sheet to a roof. (4)
45 Distinguish between a truss hanger and a gang nail with regard to their uses. (2)

46 Draw, in your ANSWER BOOK, a line diagram of a close-coupled roof truss.
Indicate the overhangs. (4)

Copyright reserved Please turn over

### Page 11

Downloaded from hlayiso.com

Civil Technology: Woodworking 11 DBE/November 2023
NSC

47 FIGURE 4.7 below shows the profile of a metal roof sheet.

MPV IN mm

FIGURE 4.7

4.7.1 Identify the type of metal roof sheet. (1)

4.7.2 Motivate why it is important to galvanise and factory-coat metal
roof sheets used in coastal areas. (2)

4.7.3 State ONE regulation regarding storing/placing of roof sheets
before installation. (1)

4.8 Calculate the centre-to-centre distance between the battens, for interlocking
roof tiles, if the tile is 450 mm long and has an overhang of 75 mm. (3)
4.9 State TWO requirements for the design and construction of roof trusses. (2)

4.10 When using an orbital sander, as shown in FIGURE 4.10 below, safe handling
and care is very important.

FIGURE 4.10

4.10.1 State ONE advantage of using an orbital sander regarding the

grain of the wood. (1)
4.10.2 Explain why you should place the power cord over your shoulder

when using an orbital sander. (1)
4.10.3 Explain why sanding dust must be removed regularly from a work

piece. (1)
4.10.4 Predict what will happen to the wood if you neglect to remove wood

dust. (1)

[40]

Copyright reserved Please turn over

### Page 12

Downloaded from hlayiso.com

Civil Technology: Woodworking 12 DBE/November 2023

NSC

QUESTION 5: CENTERING, FORMWORK, SHORING AND GRAPHICS AS

MEANS OF COMMUNICATION (SPECIFIC)

Start this question on a NEW page.

5.1

5.2

5.3

5.4

5.5

5.6

Recommend a type of shore that will be used in the following scenarios:
5.1.1 A new opening is cut into an existing wall

5.1.2 Two parallel walls showing signs of failure

Name ONE material used to make needles for shoring.

Name the component that is used to secure the joint between props and
needles.

ANSWER SHEET 5.4 shows an incomplete horizontal sectional view of
formwork for a round column.

Draw only ONE quarter (the top right quarter, indicated by A) of the formwork
with a shaped yoke/collar fastened with bolts and nuts.

ANSWER SHEET 5.5 shows an incomplete front elevation of the
constructional detail at the base of a centre with open laggings.

Complete the drawing by adding the omitted members. Print any ONE label.

ANSWER SHEET 5.6 shows a drawing of the exploded isometric view of an
incomplete long and short shoulder mortice and tenon joint for rebated
frames.

Use the detail in the stile to project and draw the tenon on the rail. Do NOT
show any hidden detail.

Copyright reserved Please turn over

{1)
(1)
(1)

(1)

(6)

(8)

(12)
[30]

### Page 13

Downloaded from hlayiso.com

Civil Technology: Woodworking 13 DBE/November 2023
NSC

QUESTION 6: SUSPENDED FLOORS, STAIRCASES, IRONMONGERY, DOORS
AND JOINING (SPECIFIC)
Start this question on a NEW page.
6.1 State TWO different ways to install locks on doors. (2)

6.2 FIGURE 6.2 below shows the steps for marking and cutting a twin mortise
and tenon joint for the bottom rail of a door.

FIGURE 6.2
6.2.1 Explain what was done in steps A—D above. (4)
6.2.2 Explain the steps of cutting out the tenon for this joint. (4)

Copyright reserved Please turn over

### Page 14

Downloaded from hlayiso.com

Civil Technology: Woodworking 14 DBE/November 2023
NSC
6.3 ANSWER SHEET 6.3 shows the top part of a framed ledged and braced

6.4

6.5

batten door with section line A-A. Use the detail on ANSWER SHEET 6.3 to
project and draw the vertical sectional view A-A.

You need to design a flight of stairs for an old age-home so that residents can
move from point A to point B with a landing in between to rest.

ANSWER SHEET 6.4 shows the incomplete view of a straight flight of stairs
indicating the following:

e The riser and tread atA
e The newel post, handrail and top landing at B

Draw FOUR steps before and FIVE steps after the landing with the newel
posts and handrails in position to complete the drawing.

FIGURE 6.5 below shows the top view of part of a suspended timber floor
with two cutting lines indicated. Use the detail on ANSWER SHEET 6.5 and
complete the sectional views by differentiating between the sectional views as
seen from A-A and B-B. Draw the floorboards on both sectional views.

r —
F ia Oo
LJ = (4 |]
_ t
A A || Bo
! OO OO
Uo Wu
FIGURE 6.5
TOTAL:

Copyright reserved

()

(9)

(14)
[40]

200

### Page 15

Downloaded from hlayiso.com

Civil Technology: Woodworking

NSC

[ CENTRE NUMBER: [LT TT J

DBE/November 2023

[EXAMINATIONNUMBER: | | | |

ANSWER SHEET 2
NO. QUESTIONS ANSWERS MARKS

4 Give ONE reason why FIGURE B 1
represents the first floor plan.

2 Name the SI unit that is used to 4
indicate dimensions on building plans.

3 | Identify number 1. 1

4 _| Identify the number indicating the 1
emergency exit.

5 | What is the purpose of number 3? 1

6 | Identify number 4. 1

7 | Identify number 5. 1

8 | Identify number 6. 41

9 | Identify number 7. 41
Deduce from the window schedule the

10 | dimensions of the window that is 2
installed at number 8.

11 | Who is the owner of the new dwelling? 1

42 | Name the elevation where the sink is 1
located.

13 | Identify the safety error in FIGURE A. 1
Deduce from the building plan why it

14 | was not approved after the first 1
submission.

Copyright reserved

### Page 16

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC

[ CENTRE NUMBER: [LTT T TT tT 4

[EXAMINATIONNUMBER: | | | | | | | | | | [| | J 4

Name the material that must be used

fs for the balusters.

16 Deduce from the notes column the
type of roof illustrated in FIGURE A.

17 How many signatures must be

indicated on this building plan?

What are the dimensions for the
18 | balusters as indicated by the
architect?

Name the material that must be used
19 | for the final finishing of the outside
wall.

Describe the end shape of the

20 balusters.

How many hinged openings are
21. | indicated on Window 1 in the window
schedule?

Draw the symbol for finished wood for

22 the boardroom table.

23 Draw the electrical symbol for a
three-pole one-way switch.

24 How many fluorescent tubes are

indicated in the office?

Copyright reserved

### Page 17

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC
[ CENTRE NUMBER: LT [ 7 7— [ [ ]
[EXAMINATIONNUMBER: | | [| | | | | | | | | | [J

Calculate the total height of the wall on
the left side of the building from the 4
finished floor level. Give your answer
in metre.

25

Calculate the area of the exterior wall
on the ground floor, that will consist of
bricks, from the finished floor level to

the top of the floor slab in the south 8
elevation in FIGURE A. Show ALL
calculations.

26

TOTAL: 40

Copyright reserved

### Page 18

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC
| CENTRE NUMBER: LTT 7 7] [ [ ]
[EXAMINATIONNUMBER: | [| | | | | | | | | | | |_|
ANSWER SHEET 3.2

Dimension paper

A B c D
3.2.1
(2)
(3)
3.2.2
(3)
Correct use of dimension paper (1)

Copyright reserved

### Page 19

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC
| CENTRE NUMBER: LITT {[ I] tT 4
[EXAMINATIONNUMBER: | | | | | | | | | | | | J J
ANSWER SHEET 3.3
A—)
|
T
|
|
|
|
|
|
l
+
A—>] ASSESSMENT CRITERIA
NO. | MARK | CANDIDATE'S MARK
1 1
2 4
3 1
4 1
5 4
6 1
7 1
8 1
9 1
10 1
11 4
12 1
13 1
TOTAL: | 13

Copyright reserved

### Page 20

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC
[| CENTRE NUMBER: LTT TT [ tT 4
[EXAMINATIONNUMBER: | | | | | | | | | | | | J| J
ANSWER SHEET 3.4
SW
a <a
ASSESSMENT CRITERIA
NO. | MARK | CANDIDATE'S MARK
1 2
2 1
3 1
TOTAL:| 4

Copyright reserved

### Page 21

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC

[| CENTRE NUMBER: Tr] | |] 7 [ J 4

[EXAMINATIONNUMBER: | | | | | | | | | | [| | [ J

ANSWER SHEET 5.4

ASSESSMENT CRITERIA
NO. MARK | CANDIDATE'S MARK
1 2
2 1
3 1
4 2
TOTAL: 6

Copyright reserved

### Page 22

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC
[ CENTRE NUMBER: LTT tT {TT 4]
[EXAMINATIONNUMBER: | | | | | | | | | | | | [ 4
ANSWER SHEET 5.5

4 CENTRE POINT
FOR ARCH

——
ASSESSMENT CRITERIA
NO. _| MARK | CANDIDATE'S MARK
1 4
2 1
3 2
4 1
5 1
6 1
7 1
TOTAL: 8

Copyright reserved

### Page 23

Downloaded from hlayiso.com

DBE/November 2023

NSC

Civil Technology: Woodworking

| CENTRE NUMBER:

| EXAMINATION NUMBER:

ANSWER SHEET 5.6

ASSESSMENT CRITERIA

MARK | CANDIDATE'S MARK

12

NO.

TOTAL:

Copyright reserved

### Page 24

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC

[ CENTRE NUMBER: LETT TT IT

[EXAMINATIONNUMBER: | | | | | | | | | | | | { J

ANSWER SHEET 6.3

A—|

ASSESSMENT CRITERIA
MARK | CANDIDATE'S MARK

~lo}en}a|eo|no| 13

jaja} a}o)o}a)a

TOTAL:

Copyright reserved

### Page 25

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC
[ CENTRE NUMBER: LETL_T ITI tT i
[EXAMINATIONNUMBER: | | | | | | | | | | [| | | J
ANSWER SHEET 6.4
HANDRAIL —y—-

=— NEWEL POST

f

LANDING

TREAD

nce .
A

ASSESSMENT CRITERIA
NO. _| MARK | CANDIDATE'S MARK
1 1
2 1
3 1
4 3
5 3
TOTAL: 9

Copyright reserved

### Page 26

Downloaded from hlayiso.com

Civil Technology: Woodworking DBE/November 2023
NSC

| CENTRE NUMBER: LT TT J

[EXAMINATION NUMBER: |_| |__| |

ANSWER SHEET 6.5

BRICK PIER

NGL

“% |-=-—— FOUNDATION ——=f3 9:

cyt eae
Srey Age g,

SECTION A-A SECTION B-B
ASSESSMENT CRITERIA

NO. MARK | CANDIDATE'S MARK
1 4
2 3
3 3
4 2
5 2
TOTAL: | 14

Copyright reserved

## Related documents

- [Civil Technology Nov 2023 (Construction) Eng](https://www.hlayiso.com/library/civil-technology-nov-2023-construction-eng/e6743728-8140-42ae-838d-282654a975a5) — Civil Technology · QP · 2023 · Eng
- [Civil Technology Nov 2023 (Civil Services) Afr](https://www.hlayiso.com/library/civil-technology-nov-2023-civil-services-afr/b820ac91-947c-4aed-821f-256aa13aabe1) — Civil Technology · QP · 2023 · Afr
- [Civil Technology Nov 2023 (Woodworking) Afr](https://www.hlayiso.com/library/civil-technology-nov-2023-woodworking-afr/f6f7ac38-fb55-4d61-bc66-5441e4cbcee0) — Civil Technology · QP · 2023 · Afr
- [Civil Technology Nov 2023 (Civil Services) Eng](https://www.hlayiso.com/library/civil-technology-nov-2023-civil-services-eng/fd47df8e-afbf-4ba2-8858-18deaf33c455) — Civil Technology · QP · 2023 · Eng
- [Civil Technology Nov 2022 (Civil Services) MG Afr](https://www.hlayiso.com/library/civil-technology-nov-2022-civil-services-mg-afr/42b5315c-825c-40e3-b394-85e0253fc0fb) — Civil Technology · Memo · 2023 · Afr
- [CIV TECH GR12 QP SEPT 2023 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept-2023-construction-afrikaans/97f8938d-02eb-46a4-a681-ef07b440e38f) — Civil Technology · QP · 2023 · Afr

## More from Grade 12 Civil Technology

- [Civil Technology (Woodworking) (Afrikaans) June 2025 Possible Answers](https://www.hlayiso.com/library/civil-technology-woodworking-afrikaans-june-2025-possible-answers/c0a65d19-28ca-4ac3-8c61-d4627d2a3133) — Memo · 2025 · Afr
- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-afrikaans/162bcc65-80ad-4384-b293-36da22468b06) — Memo · 2024 · Afr
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
