# Civil Technology Grade 12 November 2024 NSC QP (Eng)

> Grade 12 Civil Technology question paper from the November 2024 NSC (English), 24 pages. Read online or get the free PDF download, memo linked when available.

- Page: https://www.hlayiso.com/library/civil-technology-nov-2024-woodworking-eng/68d3ebd4-25f3-43cd-ada1-c179d89bb253
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 24

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 November 2024 NSC QP (Eng)](https://www.hlayiso.com/library/civil-technology-nov-2024-woodworking-eng/68d3ebd4-25f3-43cd-ada1-c179d89bb253)

## About this document

Civil Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 24 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Confidential
ey
=
Pe ad

{Wz

a ap | :
| Ufa) Department:
\ () y, Basic Education
BOYZ REPUBLIC OF SOUTH AFRICA

ams

NATIONAL
SENIOR CERTIFICATE

basic education

GRADE 12
i CIVIL TECHNOLOGY: WOODWORKING :
ty A
fF NOVEMBER 2024 5
Oat ere teva ele atel ale (alas! a ralerelateleteteteteterataialateretatetatetatetatarats le ania e”

MARKS: 200

TIME: 3 hours

This question paper consists of 17 pages and 6 answer sheets.

Copyright reserved Please turn over

### Page 2

Civil Technology: Woodworking 2 DBE/November 2024

NSC Confidential

REQUIREMENTS:

1.
2.
3.

Drawing instruments
A non-programmable calculator
ANSWER BOOK

INSTRUCTIONS AND INFORMATION

k Y N

oC oa NO

11.

12.

13.
14.

15.

16.

17.
18.

This question paper consists of SIX questions.
Answer ALL the questions.
Read ALL the questions carefully.

Answer each question as a whole. Do NOT separate subsections of
questions.

Number the answers correctly according to the numbering system used in this
question paper.

Start the answer to EACH question on a NEW page.
Do NOT write in the margins of the ANSWER BOOK.
You may use sketches to illustrate your answers.

Write ALL calculations and answers in the ANSWER BOOK or on the
attached ANSWER SHEETS.

Use the mark allocation as a guide to the length of your answers.

Make drawings and sketches in pencil, fully dimensioned and neatly finished
off with descriptive titles and notes to conform to the SANS/SABS Code of
Practice for Building Drawings.

For the purpose of this question paper, the size of a brick should be taken as
220 mm x 110 mm x 75 mm.

Use your own discretion where dimensions and/or details have been omitted.

Answer QUESTIONS 2, 3.2, 3.5, 5.2, 5.3 and 5.4 on the attached ANSWER
SHEETS using drawing instruments, where necessary.

Write your CENTRE NUMBER and EXAMINATION NUMBER on every
ANSWER SHEET and hand them in with your ANSWER BOOK, whether you
have used them or not.

Drawings in the question paper are NOT to scale due to electronic transfer.
Google Images was used as the source of all photographs and pictures.

Write neatly and legibly.

Copyright reserved Please turn over

### Page 3

Civil Technology: Woodworking 3 DBE/November 2024

QUESTION 1:

NSC Confidential

OHSA, MATERIALS, TOOLS, EQUIPMENT AND JOINING
(GENERIC)

Start this question on a NEW page.

14 Choose the correct word(s) from those given in brackets. Write only the
word(s) next to the question numbers. (1.1.1 to 1.1.10) in the ANSWER
BOOK, e.g. 1.1.11 Concrete. .

1.1.1

1.1.2
1.1.3

1.1.10

Wooden scaffold standards should not be placed more than
(4 m/3 m/6 m) apart.

Trestle scaffolds must have a maximum height of (3 m/4 m/6 m).

The material safety data sheet that accompanies hazardous
chemical substances must contain (fire-fighting measures/
flame ratio/combustion rate).

When transporting long ladders with a vehicle, (ensure that the
ladder does not protrude excessively/mark the end of the ladder
with a green flag/place ladder in an upright position).

(Galvanising/Powder coating/Electrolysis) is the process of
applying a plastic coating to a metal.

Electroplating is the process in which (the thickness of undersized
parts can be increased/metal becomes extremely hot/metals are
coated with paint).

The (thread and shank/head and pin/runout and shank) do not form
part of the length of a bolt.

The purpose of the nylon insert on a hexagonal nut is for
(decorative purposes/easy removal from a bolt/preventing backing

off).

Wooden ladders may be treated with (oil-based paint/
wood __ preservatives/water-based paint) according to the
Occupational Health and Safety Act (OHSA).

Workers carrying large equipment may not use (spirai/suspended/
fire escape) stairways that are a temporary part of a structure.

1.2 Which pictorial view below represents a nut with a built-in washer?

Ww O&O B &

A

B c D

1.3 The specifications for a Rawl bolt are R-RBL-M08/25. What does the M08
represent?

Copyright reserved

Please turn over

(1)
(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

### Page 4

Civil Technology: Woodworking 4 DBE/November 2024
NSC Confidential

1.4 Cured concrete is exposed to elements.
1.4.1 Explain the effect of cured concrete on steel reinforcement. (1)
1.4.2 Explain the advantages of cured concrete in terms of the weight it
can carry. (1)
1.6 Differentiate between the multi-detector and the /aser level in terms of the use
thereof. (2)
1.6 Describe TWO uses of the dumpy level. (2)
1.7 Describe how you will take care of a telescopic staff. (2)

[20]
QUESTION 2: GRAPHICS AS MEANS OF COMMUNICATION (GENERIC)
Start this question on a NEW page.

FIGURE A and FIGURE B on the next page show drawings that appear on a building
plan. Analyse the drawings and complete the table on ANSWER SHEET 2.

Copyright reserved Please turn over

### Page 5

Civil Technology: Woodworking

5
NSC Confidential

DBE/November 2024

30 000

PLOT 25

©

NEW DWELLING

PTB T TR BE SSS |

PLOT 23

HIBISCUS STREET

CLIVIA STREET

\

FIGURE A

NOTES:

Contractors must verify all
dimensions and levels on site
before commencing work.

Architects to be notified
of any discrepancies immediately.

Fencing: Clear-view fencing to be
used on the boundary

Architect's signature

Client's signature .

va 6 000
i!

GARAGE

4

ji

K 15

x40 W

Nb U
C

DRAWING OF
ELECTRICAL
FITTINGS

REVISION DATE:
1 14/04/2024

PRINTED BY:
FROG PRINTERS

DATE OF PRINT.
16/04/2024

DRAWING TITLE:
SITE PLAN AND FLOOR PLAN

PROJECT:

= is PROPOSED DWELLING OF MS KOCK

Q ROOMA | ON PLOT 23, CLIVIA STREET, MALUBU
os L PROJECT NO.: DRAWING NO.:
f=} = KITCHEN GR 688-646 446P2
Tv

= DATE: DRAWN: | CHECKED:
©; = = 07/04/2024 SP JOB P BOT
>

oO} ° io}
8 = L?| E SITE PLAN SCALE 1: 500
~ 2

a FLOOR PLAN SCALE 1: 100

© LOUNGE
oO = REFERENCE CODE
= | QP 4— 2024
=e ©

ROOM B \ WINDOW SCHEDULE
f=) f=} ‘ N
QI || 4000 i en
/ ‘ 800
12.000 _4| en cared
FIGURE B wi [40]

Copyright reserved

Please turn over

### Page 6

Civil Technology: Woodworking 6 DBE/November 2024
NSC Confidential

QUESTION 3: CUPBOARDS, CASEMENTS, WALL-PANELLING AND
QUANTITIES (SPECIFIC)

Start this question on a NEW page.

3.1 Give ONE word/term for EACH of the following descriptions by choosing a

word/term from the list below. Write only the word/term next to the question
numbers (3.1.1 to 3.1.5) in the ANSWER BOOK, e.g. 3.1.6 oil.

hatch; kick plate; front rail; soft board; hinges; quadrant;
handie; screws; hardboard; glue; Rawl bolts; rail

3.1.1 The item used to finish off a freestanding cupboard at the bottom

3.1.2 A material used for the bottom of a drawer

3.1.3 An item that is used to attach the doors to a cupboard

3.1.4 This item is used to join the members of a cupboard

3.1.5 The member at the top of the cupboard to which the cornice is
attached

Copyright reserved Please turn over

(1)
(1)
(1)
(1)

(1)

### Page 7

Civil Technology: Woodworking 7 DBE/November 2024
NSC Confidential

3.2 FIGURE 3.2 below shows the front view of a freestanding cupboard with a
side table without doors.

TOP ra
BACK OF CUPBOARD

SHELF Pa

BOARD
Q TABLE TOP
8 800 mm x 530 mm x 32 mm
!

]
TABLE SIDE —e|
750 mm x 530 mm x 16 mm
BOTTOM — KN
BASE FRONT RAIL
80 mm WIDE
FIGURE 3.2

Use ANSWER SHEET 3.2 and complete the cutting list for the material
needed for the cupboard and side table.

Use the following specifications:

e 16mm melamine board is used for the construction of the cupboard with
the side table.
* The back of the cupboard fits inside the frame and is made of
16 mm melamine board.
« The width of the cupboard is 900mm and the width of the table is
530 mm. (8)

Copyright reserved Please turn over

### Page 8

Civil Technology: Woodworking 8 DBE/November 2024
NSC Confidential

3.3 FIGURE 3.3 below shows an INCORRECT vertical sectional view through a
part of a casement with a fanlight.

N\v > WINDOW PANE/GLASS
b>

=| BOTTOM RAIL OF

VY FANLIGHT

[= TRANSOM

1
&
TOP RAIL OF
CASEMENT
WOODEN BEAD/
—* QUARTER ROUND
FIGURE 3.3

3.3.1 Make a neat freehand sketch of the CORRECT sectional view of
the transom in your ANSWER BOOK. Draw only the part of the

transom that is INCORRECT. (4)

3.3.2 Determine ONE mistake, other than on the transom, in this
casement with a fanlight. (1)

3.4 Wall panelling must be installed against an existing wall. Use the list below

and rearrange A to D in the CORRECT order/sequence to install the wall
panelling to the wall.

Quadrant mould

Rough grounds

Skirting

Tongue and groove boards (4)

0NWUP>

Copyright reserved Please turn over

### Page 9

Civil Technology: Woodworking 9 DBE/November 2024
NSC Confidential

3.5 ANSWER SHEET 3.5 shows the front view of a freestanding TV cupboard,
with shelves and without a door.

Project the detail of the freestanding cupboard and complete a sectional view
on cutting plane A-A. The depth of the freestanding cupboard is indicated.

Use the following specifications:

« 16mm melamine board is used for the construction of the cupboard.

e The back of the cupboard fits inside the frame and is made of 16mm
melamine board.

e The top front rail and the base front rail are flush with the front of the

cupboard. (8)
[30]

Copyright reserved Please turn over

### Page 10

Civil Technology: Woodworking 10 DBE/November 2024
NSC Confidential

QUESTION 4: ROOFS, CEILINGS, TOOLS, EQUIPMENT AND MATERIALS
(SPECIFIC)

Start this question on a NEW page.

41 Choose a description from COLUMN B that matches the item in COLUMN A.

Write only the letter (A—J) next to the question numbers (4.1.1 to 4.1.6) in the
ANSWER BOOK, e.g. 4.1.7 K.

COLUMN A COLUMN B

4.1.1 Table saw A __ always check the tension of the blade
before the machine is switched on

4.1.2 Spindle moulder
B position the work piece so that the
4.1.3 Drill press machine blade does not come into
contact with anything underneath it
4.1.4 Belt sander
C do not apply pressure, the weight of the

41.5 Jigsaw machine is enough
4.1.6 Router D always ensure that the chuck key stays
in the chuck

E ensure that the cutters are turning freely
before the machine is switched on

F use a mitre gauge at all times when
doing crosscutting

G always check that the tension of the
blade is correct

H ensure that the cutting tools rest on the
tool rest

I apply soap or wax to allow the sole to
glide easily across the work piece

J lock the table height according to the
specific type of work

(6x1)

Copyright reserved Please turn over

(6)

### Page 11

Civil Technology: Woodworking 11 DBE/November 2024

4.2

4.3

Copyright reserved

NSC Confidential
Selecting and preserving material for woodworking is essential to ensure high
quality work.

4.2.1 Describe the type of finish that lacquer provides to woodworking
projects.

4.2.2 What does the letter next to the SABS symbol on the head of the
timber indicate for commercial use?

4.2.3 When applying sanding sealer, how much drying time must be
allowed between consecutive coats?

4.2.4 Name TWO different thicknesses of timber when selecting wood
for roof trusses.

FIGURE 4.3 below shows the INCORRECT constructional detail of a part of
a conventional trap door construction.

BRANDERING

TRAP DOOR

CEILING
BOARD

FIGURE 4.3
4.3.1 Identify A.

4.3.2 Draw, in your ANSWER BOOK, a neat two-dimensional sketch of
the vertical sectional view of ONE half of the CORRECT
constructional detail of the conventional trap door. Label any TWO
parts.

Please turn over

(2)

(1)

(1)

(2)

(1)

(8)

### Page 12

Civil Technology: Woodworking 12 DBE/November 2024

44

4.5

46

47

NSC Confidential

Identify, in EACH drawing in FIGURE 4.4 below, the joining fixtures that were
used to join the members.

ft LDP eI

A B c

FIGURE 4.4

Except for a SA Howe truss, name THREE other types of roof trusses that are
commonly used.

State the maximum spacing between purlins/battens for the following roof
coverings:

46.1 Corrugated iron sheeting
46.2 Fibre-cement tiles
46.3 Metal roof tiles

Give THREE reasons why you would rather use a closed eave than an
open eave.

Copyright reserved Please turn over

(3)

(3)

(1)
(1)
(1)

(3)

### Page 13

Civil Technology: Woodworking 13 DBE/November 2024
NSC Confidential

48 The sketch in FIGURE 4.8 below shows a line diagram of the layout of the
roof members of a hipped roof on the corner of a building. identify parts

AtoD.
WALL —+=
~ ®
©)
A
\, 9)
FIGURE 4.8 (4)
49 Name ALL the timber parts that are used in the construction of a collar-tie roof

truss. (3)

[40]

Copyright reserved Please turn over

### Page 14

Civil Technology: Woodworking 14 DBE/November 2024

NSC Confidential

QUESTION 5: CENTERING, FORMWORK, SHORING AND GRAPHICS AS

MEANS OF COMMUNICATION (SPECIFIC)

Start this question on a NEW page.

5.1

5.2

5.3

5.4

Copyright reserved

Differentiate, by means of TWO line diagrams, between a king post roof truss
and a SA (Howe) roof truss. Draw ONLY the trusses with overhangs in your
ANSWER BOOK.

ANSWER SHEET 5.2 shows the side view of one pair of ribs with ties on both
sides of the ribs for a segmental arch.

Complete the drawing to show the constructional detail of the supporting
members below the ribs and ties of the centre as seen from the side.

Print any ONE label.

ANSWER SHEET 5.3 shows a sectional view of part of a multistorey building
where a new opening was cut into an existing wall.

Complete the drawing by using a line diagram to draw the following members
to support the wall:

e Dead shores
e Needle
« Braces

ANSWER SHEET 5.4 shows the incomplete view of the formwork for a
landing.

Complete the drawing by adding the omitted members of the formwork for the
landing.

Print any ONE label NOT given.

Please turn over

(12)

(6)

(5)

(7)
[30]

### Page 15

Civil Technology: Woodworking 15 DBE/November 2024
NSC Confidential

QUESTION 6: SUSPENDED FLOORS, STAIRCASES, IRONMONGERY, DOORS
AND JOINING (SPECIFIC)

Start this question on a NEW page.

6.1 Various options are provided as possible answers to the following questions.
Choose the answer and write only the letter (A-D) next to the question
numbers (6.1.1 to 6.1.5) in the ANSWER BOOK, e.g. 6.1.6 D.

6.1.1 Locks and latches are generally used to lock ...

A doors.

B cupboards.

C drawers.

D_ All the above-mentioned

6.1.2 Mortise locks are mortised into the ... of a door.

A. stile

B sail

Cpanel

D_ None of the above-mentioned

6.1.3 Rim locks are not very secure and are therefore used as ... locks.

A permanent
Bs stable

C_ temporary
D_ rebated

6.14 The ... keeps a mortise lock locked.

A latch

B_ bolt

C_ spindle hole
D face plate

6.1.5 Straight cupboard locks are available for ... doors.
A only left-handed

B only right-handed
Cleft and right-handed

D_ None of the above-mentioned
6.2 Describe the methods to join the following components:
6.2.1 Door to a frame
6.2.2 Roof trusses to a wall plate

Copyright reserved Please turn over

(1)

(1)

(1)

(1)

(1)

(2)
(2)

### Page 16

Civil Technology: Woodworking 16 DBE/November 2024
NSC Confidential

6.3 In your ANSWER BOOK, use line diagrams to differentiate between the top
views of staggered struts and in-line struts used for suspended timber floors. (6)

6.4 Sketch in your ANSWER BOOK, in good proportion, the isometric view of
ONLY the top rail with the tenon for a haunched mortice-and-tenon joint.

DO NOT show hidden detail. (8)

6.5 FIGURE 6.5 shows the front view of a four-panel door with a low lock rail,
diminishing stiles and raised panels. Section line A—A is also indicated on the
drawing.

Sketch in your ANSWER BOOK, in good proportion, the horizontal sectional
view as seen from A-A.

[>
=

FIGURE 6.5 (8)

Copyright reserved Please turn over

### Page 17

Civil Technology: Woodworking 17 DBE/November 2024
NSC Confidential

6.6 Study FIGURE 6.6 below. Match the word(s) in the list below with the labels in
FIGURE 6.6. Write only the correct word(s) next to the label (A-l) in the
ANSWER BOOK.

riser; bearer; outer stringer; cleat; half-landing; tread;
shutter board; handrail; nosing of tread; cross bearer;
baluster; newel post; horizontal brace; wall stringer; step

>

FIGURE 6.6 (9)
[40]

TOTAL: 200

Copyright reserved

### Page 18

Civil Technology: Woodworking DBE/November 2024
NSC Confidential
| CENTRE NUMBER: LT [| [| [ [ J
[EXAMINATIONNUMBER: | | | | | | LT |] | |] [ ]
ANSWER SHEET 2
NO. QUESTIONS ANSWERS MARKS
4 What is the measurement of the 1
| dwelling facing Hibiscus Street?
2. | Identify number 1. 1
3 identify the number indicating the 1
‘| building line.
4. | Identify number 2. 1
5. | Identify number 3. 1
6 Write down the abbreviation for 4
“| number 5.
7. | Explain the purpose of number 6. 4
8 How many fluorescent tubes are used 1
* | in number 7?
9 How many one-way switch single-pole 1
"| switches are in the dwelling?
10 How many built-in cupboards are in 1
* | the dwelling?
Pr What is omitted in terms of electrical 4
* | installation in the bedrooms?
12 Name TWO access points into the 2
* | dwelling.
43 How do you know in which direction 1
* | the door at number 8 will open?
Name ONE other fixture that can be
14. | installed in the bathroom indicated by 1
number 9.
15. | Identify number 10. 1

Copyright reserved

### Page 19

Civil Technology: Woodworking

NSC Confidential

| CENTRE NUMBER: LT JT J

DBE/November 2024

[EXAMINATION NUMBER: | | | |

16.

Which plot is on the eastern side of
plot number 23?

17.

How many inside doors are in the
building?

18.

How many 2 600 mm x 1 400 mm
windows are in the building?

19.

Who checked the drawing of the new
dwelling?

20.

Why will it be difficult to enter the
dwelling at number 8 if the NGL is
300 mm lower than the FFL?

21.

Who was responsible for the printing
of the building plan?

22.

Deduce from the notes column the
date that revision 1 took place.

23.

In which town will the new dwelling be
erected?

24,

Draw the symbol for a sink unit —
double.

25.

Draw the symbol for hardcore filling.

26.

Calculate the metres of clear-view
fencing that would be needed to fence
plot number 23, excluding the
driveway.

Give your answer in metres and show
ALL calculations.

27.

The internal area of the garage is
39,6 m?. Calculate the internal length
of number 11.

Give your answer in mm and show
ALL calculations.

TOTAL:

40

Copyright reserved

### Page 20

Civil Technology: Woodworking

NSC Confidential

| CENTRE NUMBER: |

|_|

DBE/November 2024

| EXAMINATION NUMBER: |

|_|

ANSWER SHEET 3.2

MEMBER QUANTITY | UNIT | LENGTH | WIDTH | THICKNESS
Top 1 mm 530 16
Front rail of
i 1 mm 868 16
Shelf board mm 868 514 16
Table top 1 mm 530
Side of table 4 mm 530 16
Back of
cupboard q mm is

(8 x 1)

Copyright reserved

### Page 21

Civil Technology: Woodworking DBE/November 2024
NSC Confidential

| CENTRE NUMBER: I | [| [| [| [ [ ]
[EXAMINATIONNUMBER: | | | | | | | | | | | | | |
ANSWER SHEET 3.5
A—-L_|| _
5
i)
|
i)
i
1
|
i
|
1
|
t
|
1
|
I |
!
A—} DEPTH OF BASE
ASSESSMENT CRITERIA
NO. | MARK | CANDIDATE'S MARK
1 2
2 1
3 1
4 1
5 1
6 2
TOTAL: 8

Copyright reserved

### Page 22

Civil Technology: Woodworking DBE/November 2024
NSC Confidential

[| CENTRE NUMBER: [| | T TTT ]

[EXAMINATIONNUMBER: | | [| | | | | | | | | | (| 4

ANSWER SHEET 5.2

RIB

VY} QR
\ P\L TIE

sh

ASSESSMENT CRITERIA
NO. MARK | CANDIDATE'S MARK
1 2
2 2
3 1
4 1
TOTAL: 6

Copyright reserved

### Page 23

Civil Technology: Woodworking DBE/November 2024
NSC Confidential

[ CENTRE NUMBER: LT TTT TT 4]

[EXAMINATIONNUMBER: | | | | | | | | | | (|_ J

ANSWER SHEET 5.3 \u

WALL ——————}
PROP/STRUT
FOLDING WEDGES ———_______|
SECOND FLOOR —— es ah g Pa ae wag Pa ee

HEAD PIECE/_ -——_|

HEADING BOARD

NEW OPENING
CUT INTO THE. ———————»
WALL
eee PR Pe Pa es
ASSESSMENT CRITERIA
NO. MARK _| CANDIDATE'S MARK

1 1

2 2

3 2

TOTAL: 5

Copyright reserved

### Page 24

Civil Technology: Woodworking

DBE/November 2024

NSC Confidential

| CENTRE NUMBER:

[|

| EXAMINATION NUMBER: |

| |

| | [| [| [| { | | | T 4

ANSWER SHEET 5.4

\\

WALL

—=—— OUTER STRING

—=——}— SHUTTER BOARD

=

CROSS BEARER/OIST

-f BEARER/JOIST

Copyright reserved

i
-_—— HORIZONTAL BRACE
1
SOLE PLATE
ASSESSMENT CRITERIA
NO. MARK | CANDIDATE'S MARK

1 2
2 2
3 1
4 2
TOTAL: 7

## Related documents

- [Civil Technology Nov 2024 (Civil Services) Afr](https://www.hlayiso.com/library/civil-technology-nov-2024-civil-services-afr/307147a5-3280-4a11-a82e-cf3e33388eb0) — Civil Technology · QP · 2024 · Afr
- [CIV TECH GR12 MEMO SEPT2024 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-afrikaans/162bcc65-80ad-4384-b293-36da22468b06) — Civil Technology · Memo · 2024 · Afr
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Civil Technology · Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Civil Technology · Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Civil Technology · Memo · 2024 · Eng
- [CIV TECH GR12 QP SEPT 2023 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept-2023-construction-afrikaans/97f8938d-02eb-46a4-a681-ef07b440e38f) — Civil Technology · QP · 2023 · Afr

## More from Grade 12 Civil Technology

- [Civil Technology (Woodworking) (Afrikaans) June 2025 Possible Answers](https://www.hlayiso.com/library/civil-technology-woodworking-afrikaans-june-2025-possible-answers/c0a65d19-28ca-4ac3-8c61-d4627d2a3133) — Memo · 2025 · Afr
- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2023 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2023-construction-english/9ab6f3f0-4774-49bf-8311-57f09822adf6) — Memo · 2023 · Eng
- [CIV TECH GR12 QP SEPT2023 Civil Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2023-civil-afrikaans/3d971330-fbba-4185-b58b-8e57fbcde1cc) — QP · 2023 · Afr
- [CIV TECH GR12 QP SEPT2023 Woodworking Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2023-woodworking-afrikaans/3e001b9e-95a3-4e0c-ad76-9bcfe29c6fff) — QP · 2023 · Afr
- [CIV TECH GR12 QP SEPT 2023 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept-2023-construction-english/4163a632-f091-41bf-8a36-993d566fb2cc) — QP · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.