# Civil Technology Grade 12 Eastern Cape Mock 2025 QP (Eng)

> Grade 12 Civil Technology question paper from the Eastern Cape Mock Exam 2025 (English), 23 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/cvlt-woodworking-eng-watermark/8e178c6e-fa7b-40f4-8a2c-936e0bee3b38
- Updated: 2026-09-27
- Subject: Civil Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2025
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 23

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Civil Technology](https://www.hlayiso.com/library/grade-12/civil-technology) › [Civil Technology Grade 12 Eastern Cape Mock 2025 QP (Eng)](https://www.hlayiso.com/library/cvlt-woodworking-eng-watermark/8e178c6e-fa7b-40f4-8a2c-936e0bee3b38)

## About this document

Civil Technology · Grade 12 · Eastern Cape Mock Exam · 2025. Question paper, 23 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

NATIONAL
                         SENIOR CERTIFICATE

                                  GRADE 12

                          SEPTEMBER 2025

         CIVIL TECHNOLOGY: WOODWORKING

MARKS:   200

TIME:    3 hours

          This question paper consists of 23 pages, including 6 answer sheets.

### Page 2

2                        CIVIL TECHNOLOGY: WOODWORKING                    (EC/SEPTEMBER 2025)

REQUIREMENTS:

1.   ANSWER BOOK

2.   Drawing instruments

3.   A non-programmable pocket calculator

INSTRUCTIONS AND INFORMATION

1.   This question paper consists of SIX questions: TWO questions are generic and FOUR
     questions are subject specific.

2.   Answer ALL the questions.

3.   Answer each question as a whole. Do NOT separate subsections of questions.

4.   Start the answer to EACH question on a NEW page.

5.   Do NOT write in the margins of the ANSWER BOOK.

6.   You may use sketches to illustrate your answers.

7.   Write ALL calculations and answers in the ANSWER BOOK or on the attached
     ANSWER SHEETS.

8.   Use the mark allocation as a guide to the length of your answers.

9.   Make drawings and sketches in pencil, fully dimensioned and neatly finished off with
     descriptive titles and notes to conform to the SANS/SABS Code of Practice for
     Building Drawings.

10. For the purpose of this question paper, the size of a brick should be taken as
    220 mm x 110 mm x 75 mm.

11. Use your own discretion where dimensions and/or details have been omitted.

12. Answer QUESTIONS 2.2, 3.4, 3.5, 5.4, 6.3 and 5.9 on the attached ANSWER
    SHEETS using drawing instruments where necessary.

13. Write your NAME on every ANSWER SHEET and hand them in with your ANSWER
    BOOK, whether you have answered the question or not.

14. Due to electronic transfer, drawings in the question paper are NOT to scale.

Copyright reserved                                                           Please turn over

### Page 3

(EC/SEPTEMBER 2025)                 CIVIL TECHNOLOGY: WOODWORKING                              3

QUESTION 1: SAFETY AND MATERIALS (GENERIC)

Start this question on a NEW page.

1.1     Identify the correct requirements regarding stairways used during construction:

        1.1.1    Stairways that will not be a permanent part of the building under
                 construction must have landings of at least
                 800 mm x 600 mm / 760 mm x 560 mm,                                            (1)

        1.1.2    … for every 2,7 m / 3,7 m or less vertical rise.                              (1)

        1.1.3    Stairways must be installed at least 30⁰ / 35⁰                                (1)

        1.1.4    … and no more than 60⁰ / 50⁰ from the horizontal.                             (1)

        1.1.5    Doors and gates opening directly into a stairway must have a platform
                 that extends at least 510 mm / 910 mm beyond the swing of the door or
                 gate.                                                                         (1)

1.2     Name any TWO materials that ladders are generally made of.                   (2 x 1)   (2)

1.3     Name the TWO characteristics that define a builder’s hoist.                  (2 x 1)   (2)

1.4     Describe the difference of the surface finish between a water-based
        paint and oil-based paint.                                                   (2 x 1)   (2)

1.5     Name any THREE properties of the curing process of concrete.                 (3 x 1)   (3)

1.6     Name the THREE advantages of electroplating.                                 (3 x 1)   (3)

1.7     Briefly describe the process of powder coating.                                        (2)

1.8     What is the main ingredient used in galvanising?                                        (1)
                                                                                               [20]

Copyright reserved                                                              Please turn over

### Page 4

4                          CIVIL TECHNOLOGY: WOODWORKING               (EC/SEPTEMBER 2025)

QUESTION 2: GRAPHICS, JOINING AND EQUIPMENT (GENERIC)

Start this question on a NEW page.

2.1 Figure 2.1 on ANSWER SHEET A shows an incomplete floorplan of building,
    scale 1 : 100 is used.

      Complete the floorplan by using the following information:

      2.1.1      Outside door 2.1.A                                                       (2)

      2.1.2      Window 2.1.B                                                             (2)

      2.1.3      Water closet 2.1.C                                                       (2)

      2.1.4      Washbasin 2.1.D                                                          (2)

      2.1.5      Wash tub 2.1.E                                                           (2)

      2.1.6      One-way switch-single pole 2.1.F                                         (2)

      2.1.7      Fluorescent light 2.1.G                                                  (2)

      2.1.8      Socket outlet 2.1.H                                                      (2)

      2.1.9      Grease trap 2.1.I                                                        (2)

      2.1.10     Wall light 2.1.J                                                         (2)

2.2 FIGURE 2.2 below shows a surveying tool that is used on a construction site.
    Study the drawing and answer the questions that follow.

             A                                                                  B

           C

                                       FIGURE 2.2

     2.2.1       Identify the parts A to C.                                                   (3)

     2.2.2       Explain how you will take care of part A.                                    (2)

 Copyright reserved                                                        Please turn over

### Page 5

(EC/SEPTEMBER 2025)               CIVIL TECHNOLOGY: WOODWORKING                         5

2.3 FIGURE 2.3 below shows the readings of a dumpy level on a telescopic staff.
    Answer the following questions with regard to the readings.

                                    1. 5

                                           1.4

                                   FIGURE 2.3

     2.3.1      What is the height reading on the staff?                                      (1)

     2.3.2      What are the minimum and maximum distances that could be determined
                accurately on the staff?                                                      (2)

2.4 Name the maintenance measures for the multi-detector with reference to the
    following facets:

     2.4.1      Cleaning method                                                               (1)

     2.4.2      Storing over a long period                                                    (1)

2.5 Identify the types of nuts illustrated in FIGURES A to C.

               FIGURE A                    FIGURE B             FIGURE C                      (3)

 Copyright reserved                                                        Please turn over

### Page 6

6                          CIVIL TECHNOLOGY: WOODWORKING                    (EC/SEPTEMBER 2025)

2.6 The pictures below illustrate the steps followed when fixing material to a floor with
    a fastener.

                  A                    B                   C                D

     2.6.1      Identify the fastener that is used in D.                                           (1)

     2.6.2      Describe the steps from A to D above in your ANSWER BOOK.                          (4)

     2.6.3      Justify the use of this fastener when securing the bracket of a heavy gate
                to a wall.                                                                      (2)
                                                                                               [40]

                                                                    TOTAL SECTION A:               60

 Copyright reserved                                                             Please turn over

### Page 7

(EC/SEPTEMBER 2025)                   CIVIL TECHNOLOGY: WOODWORKING                          7

QUESTION 3: CASEMENTS, CUPBOARDS, WALL-PANELLING AND
            QUANTITIES (SPECIFIC)

Start this question on a NEW page.

3.1    Give ONE word/term for EACH of the following descriptions by choosing a
       word/term from the list below. Write only the word/term next to the question
       numbers (3.1.1 to 3.1.5) in the ANSWER BOOK, for example 3.1.6 Glazing bead.

        Top rail, Window pane, Mullion, Drip groove, Casement, Fanlight, Sill, Glazing
                  bars, Frame stile, Frame head, Front rail, Oval hanging rail

       3.1.1    The bottom horizontal member of the casement frame fixed to the wall
                by means of horns.                                                                (1)

       3.1.2    The small window above the opening of a door or window.                           (1)

       3.1.3    The middle vertical member between casement stiles.                               (1)
       3.1.4    The outer vertical members of the frame.                                          (1)
       3.1.5    It is used to fasten the cornice.                                                 (1)
3.2    Draw, in your ANSWER BOOK, a neat freehand sketch of the sectional view of
       only the top rail of a casement.                                                           (3)
3.3    FIGURE 3.3 below shows the sectional view of a tongue and groove wall panel
       from the floor to the ceiling, fastened to a 110 mm thick wall. Study the drawing
       and answer the questions that follow.

                                            FIGURE 3.3

       3.3.1    Identify parts A–E.                                                               (5)

Copyright reserved                                                             Please turn over

### Page 8

8                       CIVIL TECHNOLOGY: WOODWORKING                 (EC/SEPTEMBER 2025)

3.4    FIGURE 3.4 below shows the built in-cupboard without the doors.
       Use ANSWER SHEET B (3.4) and draw a vertical sectional view of the
       cupboard to scale 1 : 10.

                                           A

                                           A

                                       FIGURE 3.4

       Use the following specification:
       • All shelves and sides are 16 mm thick
       • The back is 3 mm thick
       • Depth of cupboard is 570 mm
       • Show hanging rail in the sectional view                                            (8)

Copyright reserved                                                       Please turn over

### Page 9

(EC/SEPTEMBER 2025)                CIVIL TECHNOLOGY: WOODWORKING                              9

3.5    FIGURE 3.5 below shows the floor plan of a building with a gable roof.
       The external measurements are 9 000 mm x 5 000 mm.

                                                                       150
                                               9 000

                                            FIGURE 3.5

       Use the following specifications:
       • Walls are 220 mm thick
       • South African roof truss
       • Corrugated iron sheet is used as roof covering
       • Cover width of the corrugated iron sheet is 610 mm
       • True length of a rafter 2 900 mm
       • Corrugated iron sheet projects 50 mm past the gutter

       Use the dimension sheet on ANSWER SHEET C (3.5) and calculate the
       following:

       3.5.1    The area of roof underlay for the building                                         (5)

       3.5.2    The total number of roofing sheets                                             (4)
                                                                                              [30]

Copyright reserved                                                              Please turn over

### Page 10

10                        CIVIL TECHNOLOGY: WOODWORKING                      (EC/SEPTEMBER 2025)

QUESTION 4: ROOFS, CEILINGS, TOOLS AND EQUIPMENT AND MATERIALS
            (SPECIFIC)

Start this question on a NEW page.

4.1   Choose a description from COLUMN B that matches the item in COLUMN A.
      Write only the letter (A–H) next to the question numbers (4.1.1 to 4.1.6) in the
      ANSWER BOOK, for example 4.1.7 L.

                 COLUMN A                                 COLUMN B
        4.1.1    Lathe                 A    stock should be fed slowly into the
                                            cutter

        4.1.2    Orbital sander        B    ensure that all clamps and locking
                                            handles are locked in place before
                                            switching on the machine

        4.1.3    Electric plane        C    ensure that the stock moves freely

        4.1.4    Radial arm saw        D    ensure a clearance of 1 mm between
                                            the tip of the bit and the cutting edge
                                            of hollow chisel

        4.1.5    Spindle moulder       E    do not apply pressure, the weight of
                                            the machine is enough

        4.1.6    Mortising machine     F    to cut out circles, drill a hole through
                                            which to insert the blade

                                       G    check the timber for loose knots, nails
                                            and sand before planning

                                       H    lock the table height according to
                                            specific type of work
                                                                                   (1 x 6)     (6)

Copyright reserved                                                               Please turn over

### Page 11

(EC/SEPTEMBER 2025)               CIVIL TECHNOLOGY: WOODWORKING                           11

4.2   FIGURE 4.2 below shows a woodworking machine. Study the picture and answer
      the questions that follow.

                                          FIGURE 4.2

      4.2.1      Identify the machine in FIGURE 4.2.                                            (1)

      4.2.2      Describe TWO safety precautions that should be taken to ensure safe
                 handling of the blade.                                        (2 x 1)          (2)

      4.2.3      Explain how you would take care of the blade.                                  (2)

4.3   Selecting and preserving timber is essential for high quality work.

      4.3.1      What does the number next to SABS symbol on the head of the timber
                 indicate for commercial use?                                                   (1)

      4.3.2      Explain the treatment of brushes between application of sanding sealer
                 and upon completion of the work                                                (2)

      4.3.3      Name TWO different width of timber when selecting wood for roof
                 trusses.                                                                       (2)

4.4   Trap doors are fitted in a ceiling to allow access to roof space.

      4.4.1      Name TWO parts of a conventional trap door.                    (2 x 1)         (2)

      4.4.2      Recommend measurements of timber that is commonly used for a trap
                 door construction below the roof trusses.                                      (2)

Copyright reserved                                                           Please turn over

### Page 12

12                            CIVIL TECHNOLOGY: WOODWORKING                 (EC/SEPTEMBER 2025)

4.5   Name the different types of roof underlays for EACH of the following roofs:

      4.5.1      Tiled roof                                                                       (1)

      4.5.2      Corrugated roof sheet                                                            (1)

      4.5.3      Thatch roof                                                                      (1)

4.6   Draw in your ANSWER BOOK a top view of a roof to show the valley between
      two inclined roofs.                                                                         (3)

4.7   In modern construction a variety of methods is used to secure the components of
      roof trusses.
      Differentiate by identifying the joining method that can be used in each of the
      following instances:

      4.7.1      To fix purlins to roof trusses                                                   (1)

      4.7.2      To prevent clay and concrete tiles from being lifted by strong winds             (1)

      4.7.3      Fixed to members of roof truss by means of permfix nails through pre-
                 drilled holes to ensure effective connection                                     (1)

4.8   FIGURE 4.8 below shows details of a corner of a hipped end. Study the drawing
      and answer the questions that follow.

                                            FIGURE 4.8

      4.8.1      Identify parts A–E.                                                              (5)

      4.8.2      Define a hipped-end roof.                                                        (2)

      4.8.3      Explain what you understand about the eaves of a roof.                           (2)

      4.8.4      Differentiate between an open eave and a closed eave.                         (2)
                                                                                              [40]

Copyright reserved                                                             Please turn over

### Page 13

(EC/SEPTEMBER 2025)                 CIVIL TECHNOLOGY: WOODWORKING                                 13

QUESTION 5: CENTERING, FORMWORK, SHORING AND GRAPHICS AS
            MEANS OF COMMUNICATION (SPECIFIC)

Start this question on a NEW page.

5.1   FIGURE 5.1 below shows the pictorial view of the construction details at the
      base of a centre. Study the picture and answer the questions that follow.

                                      FIGURE 5.1

      5.1.1     Identify parts D and E.                                                            (2)

      5.1.2     Describe the purpose of part labelled B.                                           (1)

5.2   The information given below are the stages on how to erect centre for
      segmental and semi-circular arches.
      Analyse and rearrange the steps in the correct sequence. Write only the
      numbers of the statements in your ANSWER BOOK.                                               (5)

      5.2.1     Place the sleeper or soleplate for the props in a level position on the
                ground.

      5.2.2     Position the props on the sleepers against the reveals of the opening.

      5.2.3     Build the wall up to the height of the springing line of the arch.

      5.2.4     Insert the bearer and folding wedges at the top of the props.

      5.2.5     Ensure that the span is correct.

Copyright reserved                                                                   Please turn over

### Page 14

14                      CIVIL TECHNOLOGY: WOODWORKING                 (EC/SEPTEMBER 2025)

5.3   Draw in your ANSWER BOOK, in good proportion, a single-line diagram of a
      SA (Howe) roof truss. Label any ONE part of the truss.                           (9)

5.4   ANSWER SHEET D (5.4) shows the incomplete formwork for a square column.
      Use ANSWER SHEET D (5.4) and complete it by drawing in good proportion
      the horizontal section through a square column.                                 (7)

5.5   Draw in your ANSWER BOOK, in good proportion, a neat two-dimensional
      sketch of the detail of the base of a dead shore.

      Show the following on your drawing:

      •   Dead shore
      •   Folding wedges
      •   Soleplate
      •   Steel dog
      •   Any ONE label                                                               (6)
                                                                                     [30]

Copyright reserved                                                       Please turn over

### Page 15

(EC/SEPTEMBER 2025)                     CIVIL TECHNOLOGY: WOODWORKING                      15

QUESTION 6: SUSPENDED FLOORS, STAIRCASES, IRONMONGERY,
            DOORS AND JOINING (SPECIFIC)

Start this question on a NEW page.

6.1 Various options are given as possible answers to the following questions.
    Choose the answer and write only the letter (A–D) next to the question numbers
    (6.1.1 to 6.1.5) in the ANSWER BOOK, for example 6.1.6 E.

     6.1.1    In suspended timber floors, longitudinal edges of the floor boards should
              be at least … from the plaster to allow movement.

              A 21 mm
              B 6 mm
              C 12 mm
              D 8 mm                                                                        (1)

     6.1.2    Vertical member between two consecutive treads.

              A      Rise
              B      Newel post
              C      Tread
              D      Riser                                                                  (1)

     6.1.3    It is screwed onto the internal surface of the door.

              A      Mortise lock
              B      Rim lock
              C      Straight cupboard lock
              D      Drawer or till lock                                                    (1)

     6.1.4    Tall, narrow units placed on the sides of entry doors.

              A      Fanlights
              B      Side lights
              C      Mullion
              D      Muntin                                                                 (1)

     6.1.5    IBR sheeting and corrugated iron sheets are secured to purlins with ...

              A      hurricane clips.
              B      roofing nails.
              C      truss hanger.
              D      gang nail.                                                             (1)

Copyright reserved                                                            Please turn over

### Page 16

16                        CIVIL TECHNOLOGY: WOODWORKING                      (EC/SEPTEMBER 2025)

6.2 Draw in your ANSWER BOOK in good proportion, two horizontal sectional views
    to show the difference between a door frame and jamb lining fixed to a wall.
    Print the title below EACH of the drawings.                                               (6)

6.3 ANSWER SHEET E (6.3) shows the isometric view of the rail of haunched
    mortise and tenon joint.
    Use ANSWER SHEET E (6.3) and draw the isometric view of the adjoining stile
    No hidden details are required.                                                           (6)

6.4 FIGURE 6.4 below shows a part of a suspended timber floor. Identify parts
    labelled 6.4.1 to 6.4.6.

                                              6.4.1
                                                                            6.4.2

                                                                            6.4.3
                                                                            6.4.4

                                                                            6.4.5

                                                                            6.4.6

                                         FIGURE 6.4                                           (6)

6.5 Briefly motivate why all debris below suspended timber floor must be removed.             (2)

6.6 Differentiate between the mortise lock and night latch with regard to their
    placement and functions.                                                                  (4)

6.7 FIGURE 6.7 below shows two methods of joining floor joists to wall in upper
    level suspended timber floor.

                                         FIGURE 6.7

     6.7.1    Describe the joining methods used to join the floor joists to wall in A and
              B respectively.                                                                 (2)

     6.7.2    Justify why you would prefer method A.                                          (1)

Copyright reserved                                                              Please turn over

### Page 17

(EC/SEPTEMBER 2025)               CIVIL TECHNOLOGY: WOODWORKING                              17

6.8 FIGURE 6.8 on ANSWER SHEET F (6.8) shows the top view of a wall around a
    staircase. Use ANSWER SHEET F (6.8) and draw in good proportion the top
    view of a flight of stairs with an open well and half-landing within the given wall.     (6)

6.9 Explain TWO purposes of handrail in staircase construction.                              (2)
                                                                                            [40]

                                                                                TOTAL:       200

Copyright reserved                                                              Please turn over

### Page 18

18                        CIVIL TECHNOLOGY: WOODWORKING                       (EC/SEPTEMBER 2025)

                                 CIVIL TECHNOLOGY                   NAME AND
  ANSWER SHEET            A           (GENERIC)                     SURNAME:

2.1     Use the information on ANSWER SHEET A and complete the floor plan on
        scale 1 : 100.                                                                     (20)

                                  2.1.I           2.1.J

                                             KITCHEN
                2.1.C    2.1.D    2.1.E
          BATHROOM

                                             LIVING AREA

                  ROOM                                    2.1.G

                                     2.1.F         2.1.H

                                          2.1.A             2.1.B

                                                    Outside door 2.1.A                 2
                                                    Window 2.1.B                       2
                                                    Water closet 2.1.C                 2
                                                    Washbasin 2.1.D                    2
                                                    Wash tub 2.1.E                     2
                                                    One-way switch-single pole 2.1.F   2
                                                    Fluorescent light 2.1.G            2
                                                    Socket outlet 2.1.H                2
                                                    Grease trap 2.1.I                  2
                                                    Light wall mounted 2.1.J           2
                                                                                TOTAL 20

 Copyright reserved                                                               Please turn over

### Page 19

(EC/SEPTEMBER 2025)            CIVIL TECHNOLOGY: WOODWORKING                         19

                                                   NAME AND
 ANSWER SHEET              CIVIL TECHNOLOGY
                      B       SPECIFIC
                                                   SURNAME

Use ANSWER SHEET B (3.4) and draw a vertical sectional view of the cupboard to
scale 1 : 100.

                                       ASSESSMENT               MARK     CANDIDATE'S
                                       CRITERIA                             MARK
                                       Front rail                  1
                                       Top shelf                   1
                                       Middle shelf                1
                                       Hanging rail                1
                                       Kick plate                  1
                                       Back of base                1
                                       Back of cupboard            1
                                       Application of scale:       1
                                       TOTAL:                      8

Copyright reserved                                                      Please turn over

### Page 20

20                       CIVIL TECHNOLOGY: WOODWORKING       (EC/SEPTEMBER 2025)

 ANSWER SHEET                                    NAME AND
                             CIVIL TECHNOLOGY
                         C        (SPECIFIC)
                                                 SURNAME:

                                     DIMENSION PAPER
           A         B       C                           D
3.5.1

3.5.2

Copyright reserved                                              Please turn over

### Page 21

(EC/SEPTEMBER 2025)           CIVIL TECHNOLOGY: WOODWORKING                         21

 ANSWER SHEET                                     NAME AND
                          CIVIL TECHNOLOGY
                      D        (SPECIFIC)
                                                  SURNAME:

Use ANSWER SHEET D (5.4) and complete by drawing in good proportion, the horizontal
section through square column.

                                   ASSESSMENT                        CANDIDATES
                                                            MARK
                                   CRITERIA                          MARK
                                   Members                    6
                                   Correctness of drawing     1
                                   TOTAL                      7

Copyright reserved                                                     Please turn over

### Page 22

22                       CIVIL TECHNOLOGY: WOODWORKING              (EC/SEPTEMBER 2025)

 ANSWER SHEET                                    NAME AND
                            CIVIL TECHNOLOGY
                     E           (SPECIFIC)
                                                 SURNAME

                                         NO    ASSESSMENT CRITERIA           MARK
                                         1     Correctness of stile          1
                                         2     Parts of the stile            5
                                                                    TOTAL:   6

Copyright reserved                                                     Please turn over

### Page 23

(EC/SEPTEMBER 2025)          CIVIL TECHNOLOGY: WOODWORKING                    23

                                                NAME AND
 ANSWER SHEET             CIVIL TECHNOLOGY
                      F        (SPECIFIC)
                                                SURNAME:

                          ASSESSMENT CRITERIA        MARK CANDIDATE’S
                                                          MARK
                          Members                    5
                          Correctness of drawing     1
                                            TOTAL:   6

Copyright reserved                                               Please turn over

## Related documents

- [CIV TECH GR12 QP SEPT 2023 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept-2023-construction-afrikaans/97f8938d-02eb-46a4-a681-ef07b440e38f) — Civil Technology · QP · 2023 · Afr
- [CIV TECH GR12 QP SEPT2023 Civil Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2023-civil-afrikaans/3d971330-fbba-4185-b58b-8e57fbcde1cc) — Civil Technology · QP · 2023 · Afr
- [CIV TECH GR12 QP SEPT2023 Woodworking Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2023-woodworking-afrikaans/3e001b9e-95a3-4e0c-ad76-9bcfe29c6fff) — Civil Technology · QP · 2023 · Afr
- [CIV TECH GR12 QP SEPT 2023 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept-2023-construction-english/4163a632-f091-41bf-8a36-993d566fb2cc) — Civil Technology · QP · 2023 · Eng
- [CIV TECH GR12 QP SEPT2022 Woodworking Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-woodworking-afrikaans/c4790570-dabd-463c-94fa-aa1715b1a542) — Civil Technology · QP · 2022 · Afr
- [CIV TECH GR12 QP SEPT2022 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-qp-sept2022-woodworking-english/c3b4a7c0-761a-45aa-a578-9b98afc86830) — Civil Technology · QP · 2022 · Eng

## More from Grade 12 Civil Technology

- [Civil Technology (Woodworking) (Afrikaans) June 2025 Possible Answers](https://www.hlayiso.com/library/civil-technology-woodworking-afrikaans-june-2025-possible-answers/c0a65d19-28ca-4ac3-8c61-d4627d2a3133) — Memo · 2025 · Afr
- [Civil Technology Nov 2025 (Construction) MG Eng](https://www.hlayiso.com/library/grade-12-civil-technology-2025-nsc-november-exam-memorandum/0e265899-dc44-4809-aabf-8f374f1af392) — Memo · 2025 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction Afrikaans](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-afrikaans/162bcc65-80ad-4384-b293-36da22468b06) — Memo · 2024 · Afr
- [CIV TECH GR12 MEMO SEPT2024 Civil Services English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-civil-services-english/c1f2441d-22ba-4ae6-9e56-137cc442080c) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Construction English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-construction-english/4d9c54ef-f526-46ad-82d4-8dd419eafb50) — Memo · 2024 · Eng
- [CIV TECH GR12 MEMO SEPT2024 Woodworking English](https://www.hlayiso.com/library/civ-tech-gr12-memo-sept2024-woodworking-english/6e7f4be5-4ffb-4654-b98b-b4cc4dfc4cc7) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
