# Electrical Technology Grade 12 Eastern Cape Prelim 2024 QP

> Grade 12 Electrical Technology question paper from the Eastern Cape Prelim Exam 2024 (English), 14 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-digital-english/9fcfef2b-6d5e-4601-853a-24a2a3993617
- Updated: 2026-09-27
- Subject: Electrical Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2024
- Exam period: Eastern Cape Prelim Exam
- Curriculum: CAPS
- Pages: 14

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 Eastern Cape Prelim 2024 QP](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-digital-english/9fcfef2b-6d5e-4601-853a-24a2a3993617)

## About this document

Electrical Technology · Grade 12 · Eastern Cape Prelim Exam · 2024 · English. Question paper, 14 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                   NATIONAL
                              SENIOR CERTIFICATE

                                   GRADE 12

                               SEPTEMBER 2024

  ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS

MARKS:     200

TIME:      3 hours

  This question paper consists of 14 pages, including a 1-page formula sheet and an answer sheet.

                            Hosted by www.ecexams.co.za.

### Page 2

Downloaded from hlayiso.com
 2                   ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS          (EC/SEPTEMBER 2024)

 INSTRUCTIONS AND INFORMATION

 1.     This question paper consists of SIX questions.

 2.     Sketches and diagrams must be large, neat and fully labelled.

 3.     Show ALL calculations and round off answers to TWO decimal places.

 4.     Number the answers correctly according to the numbering system used in
        this question paper.

 5.     You may use a non-programmable calculator.

 6.     Show the units for ALL answers of calculations.

 7.     A formula sheet is provided at the end of this question paper.

 8.     Write neatly and legibly.

Copyright reserved                                                           Please turn over

                           Hosted by www.ecexams.co.za.

### Page 3

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2024)           ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                  3

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS

 Various options are given as possible answers to the following questions. Choose
 the answer and write only the letter (A–D) next to the question numbers (1.1 to 1.15)
 in the ANSWER BOOK, for example 1.16 D.

 1.1    The purpose of the Occupational Health and Safety Act is to …

        A     provide for the health and safety of persons at work.
        B     provide for the health and safety of persons at home.
        C     prevent wear and tear on machinery.
        D     prevent workers from using machinery.                                       (1)

 1.2    What is the function of a bistable multivibrator?

        A     To switch on a circuit.
        B     To generate a controlled clock pulse.
        C     To form a debounce circuit.
        D     To set and reset the output of a multivibrator circuit.                     (1)

 1.3    Pin 3 of a 555 Integrated Circuit (IC) is called:

        A     Vcc.
        B     ground.
        C     output.
        D     input.                                                                      (1)

 1.4    The output waveform of a Schmitt trigger circuit will always be a … wave.

        A     sine
        B     triangular
        C     radio
        D     square                                                                       (1)

 1.5    The bistable multivibrator has the following characteristics:

        A     Free running with ONE input
        B     Free running with TWO inputs
        C     TWO stable states with TWO inputs
        D     NO stable states with ONE input                                              (1)

 1.6    The maximum current a 555 IC can either sink or source is:

        A     2A
        B     200 A
        C     2 mA
        D     20 mA                                                                        (1)

Copyright reserved                                                            Please turn over

                            Hosted by www.ecexams.co.za.

### Page 4

Downloaded from hlayiso.com
 4                   ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS           (EC/SEPTEMBER 2024)

 1.7    The function of an encoder is to …

        A     convert an analogue signal to a digital signal.
        B     convert a digital signal to an analogue signal.
        C     convert a binary code into a recognisable decimal form.
        D     convert a decimal code into a recognisable binary form.                     (1)

 1.8    With reference to microcontrollers, the term RAM means:

        A     Read All Memory
        B     Random Allocation Memory
        C     Read and Memorise Memory
        D     Random Access Memory                                                        (1)

 1.9    With reference to microcontrollers, a … is an example of an input.

        A     sensor
        B     motor
        C     monitor
        D     LED display                                                                 (1)

 1.10 What will happen to the value of a light dependant resistor (LDR) if the light
      shining on it increases?

        A     It will remain the same.
        B     It will first increase and then decrease.
        C     It will increase.
        D     It will decrease.                                                           (1)

 1.11 Pulse triggered flip-flop circuits are also referred to as:

        A     Master/Slave
        B     Follow my lead
        C     Simultaneous trigger
        D     Continuous trigger                                                          (1)

 1.12 A fast temporary memory that allows information to be stored and retrieved
      by the system as it operates, is called the …

        A     ROM.
        B     RAM.
        C     CPU.
        D     I/O unit.                                                                   (1)

 1.13 The … is where the timing signal is delayed by a fraction of time through
      each flip-flop.

        A     ripple counter
        B     down counter
        C     frequency divider
        D     propagation delay                                                           (1)

Copyright reserved                                                             Please turn over

                            Hosted by www.ecexams.co.za.

### Page 5

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2024)              ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS               5

 1.14 The term ‘debugging’ refers to:

        A       Identify and remove errors
        B       Find bugs and kill them
        C       Find bugs and remove them
        D       All the above                                                            (1)

 1.15 A(n) … is a specialised op-amp circuit that compares two input voltages
      and produces an output that is always at either one of the two states.

        A       integrator
        B       differentiator
        C       comparator
        D       Schmitt trigger                                                          (1)
                                                                                        [15]

 QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

 2.1    Give the meaning of the following with reference to the Occupational Health
        and Safety Act, 1993 (Act 85 of 1993).

        2.1.1     Risk                                                                   (1)

        2.1.2     Safe                                                                   (1)

 2.2    Explain the purpose of the Occupational Health and Safety Act.                   (2)

 2.3    Name THREE unsafe conditions that cause most accidents in the
        workshop.                                                                        (3)

 2.4    Describe THREE standard treatments for electric shock after the electricity
        has been removed.                                                                (3)
                                                                                        [10]

Copyright reserved                                                            Please turn over

                             Hosted by www.ecexams.co.za.

### Page 6

Downloaded from hlayiso.com
 6                    ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS           (EC/SEPTEMBER 2024)

 QUESTION 3: SWITCHING CIRCUITS

 3.1   Name ONE application of a monostable multivibrator.                                 (1)

 3.2   Name the type of the multivibrator that:

       3.2.1      Produces one pulse cycle of ‘high and low’ when a trigger pulse is
                  applied.                                                                 (1)

       3.2.2      Changes state when a trigger pulse is applied and remains in that
                  state until the next trigger pulse is applied.                           (1)

 3.3   FIGURE 3.3 and TABLE 3.3 below show the resistor values, output voltages
       and gain of a summing amplifier. Refer to FIGURE 3.3 and study TABLE 3.3
       below to answer the following questions.

                            FIGURE 3.3: SUMMING AMPLIFIER

                        RESISTOR VALUES                         OUTPUT        GAIN
            R1           R2       R3          RF                  V OUT       β (AV)
          20 kΩ        20 kΩ    20 kΩ       20 kΩ                   B            1
          20 kΩ        20 kΩ    20 kΩ       40 kΩ                + 5,2 V        D
           5 kΩ        10 kΩ    20 kΩ       40 kΩ                   C          4,08
          20 kΩ        20 kΩ    20 kΩ         A                 + 10,4 V         4
                                      TABLE 3.3

       3.3.1    State the function of a summing amplifier.                                 (2)

       3.3.2    Calculate the output voltage at B.                                         (3)

       3.3.3    Calculate the output voltage at C.                                         (3)

       3.3.4    Calculate the value of the feedback resistors at A.                        (3)

       3.3.5    Calculate the total gain at D.                                             (3)

Copyright reserved                                                             Please turn over

                            Hosted by www.ecexams.co.za.

### Page 7

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2024)           ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                   7

 3.4    Refer to FIGURE 3.4 below and answer the questions that follow.

                               FIGURE 3.4: COMPARATOR

        3.4.1    Explain what is meant with open loop with reference to
                 FIGURE 3.4.                                                              (2)

        3.4.2    Describe the principles of operation of a comparator.                    (6)

 3.5    Draw the circuit diagram for a passive integrator.                                (4)

 3.6    Name THREE key operating points of the op-amp integrator circuit.                 (3)

 3.7    Explain how you would vary the length of time that a monostable
        multivibrator circuit output stays ‘HIGH’.                                        (3)

 3.8    With reference to the astable multivibrator op-amp circuit, explain the term
        feedback.                                                                         (3)

 3.9    Draw a fully labelled circuit diagram for an astable multivibrator op-amp
        circuit.                                                                          (6)

 3.10   Explain the principle of operation of a day/night switching circuit.              (6)
                                                                                         [50]

Copyright reserved                                                             Please turn over

                           Hosted by www.ecexams.co.za.

### Page 8

Downloaded from hlayiso.com
 8                   ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS             (EC/SEPTEMBER 2024)

 QUESTION 4: SEMICONDUCTOR DEVICES

 4.1    Identify pin 7 of a 741 op-amp.                                                       (1)

 4.2    Name the TWO primary building blocks of a 555 IC.                                     (2)

 4.3    Name TWO modes the 555 IC is set up to function in.                                   (2)

 4.4    With reference to FIGURE 4.4 below, answer the following questions.

                                     FIGURE 4.4: OP-AMP

        4.4.1    Identify the op-amp in FIGURE 4.4.                                           (1)

        4.4.2    Calculate the gain of the amplifier if the feedback resistor has a value
                 of 1 kΩ and the input resistor has a value of 1 900 Ω.                       (3)

 4.5    With reference to the 555 timer IC, answer the questions below.

        4.5.1    State the voltage parameters between which a 555 timer can operate.          (2)

        4.5.2    Explain the astable mode of operation of a 555 timer.                        (2)

        4.5.3    Explain the function of pin 6 (threshold) on a 555 IC.                       (3)

 4.6    With reference to op-amp characteristics, explain the term bandwidth.                (4)
                                                                                            [20]

Copyright reserved                                                               Please turn over

                            Hosted by www.ecexams.co.za.

### Page 9

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2024)           ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                     9

 QUESTION 5: DIGITAL AND SEQUENTIAL DEVICES

 5.1    State ONE application of the up/down counter.                                        (1)

 5.2    FIGURE 5.2 below represents the logic symbol of a flip-flop.

                                          FIGURE 5.2

        5.2.1    Identify the flip-flop in FIGURE 5.2.                                        (1)

        5.2.2    Explain how the circuit is designed to eliminate any illegal states in
                 the operation of this flip-flop.                                             (4)

        5.2.3    Name TWO applications of this type of flip-flop.                             (2)

 5.3    Refer to the LED seven-segment display and explain the difference between
        a common anode and a common cathode.                                                  (4)

 5.4    Refer to FIGURE 5.4 below of a three-stage binary counter and answer the
        questions that follow.

                                          FIGURE 5.4

        5.4.1    Complete the timing diagrams for this counter on the ANSWER
                 SHEET for QUESTION 5.4.1.                                                    (8)

         5.4.2   State whether the circuit in FIGURE 5.4 is synchronous or
                 asynchronous.                                                                (1)

Copyright reserved                                                               Please turn over

                            Hosted by www.ecexams.co.za.

### Page 10

Downloaded from hlayiso.com
 10                    ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS        (EC/SEPTEMBER 2024)

 5.5    List FOUR types of shift registers that are available.                            (4)

 5.6    Name TWO methods to display information in digital systems.                       (2)

 5.7    Name TWO disadvantages of propagation delay.                                      (2)

 5.8    Explain the disadvantage of up/down counters in relation to normal up or down
        counter.                                                                          (2)

 5.9    Explain the difference between a full sequence counter and a truncated
        counter.                                                                          (4)

 5.10 Name TWO applications of counters.                                                  (2)

 5.11 With reference to FIGURE 5.11 below, answer the questions follow.

                                                 OR

                                           FIGURE 5.11

        5.11.1       Identify the circuit in FIGURE 5.11.                                 (1)

Copyright reserved                                                           Please turn over

                              Hosted by www.ecexams.co.za.

### Page 11

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2024)             ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS             11

        5.11.2       Draw a truth table for the circuit in FIGURE 5.11.                   (5)

        5.11.3       Explain the function of the circuit in FIGURE 5.11.                  (2)

 5.12 State TWO maximum values that should be considered when working with a
      LED display unit.                                                                   (2)

 5.13 Draw a fully labelled circuit diagram of a D latch flip-flop using NAND gates,
      EXCLUSIVE OR gates and an INVERTER.                                                (8)
                                                                                        [55]

 QUESTION 6: MICROCONTROLLERS

 6.1    State ONE type of communication protocol.                                         (1)

 6.2    Define communication protocol.                                                    (2)

 6.3    Answer the questions that follow with reference to communication protocols.

        6.3.1        Name THREE applications of the RS-485.                               (3)

        6.3.2        State the line configuration of the RS-485.                          (1)

 6.4    Explain the difference between a microprocessor and a microcontroller with
        reference to the hardware of microcontrollers.                                    (4)

 6.5    Refer to a serial communication interface and answer the questions that
        follow.

        6.5.1        Write out the acronym UART in full.                                  (4)

        6.5.2        Explain the function of the UART.                                    (5)

 6.6    Answer the following questions with reference to communication in a
        microcontroller.

        6.6.1        Explain the function of the system bus.                              (3)

        6.6.2        Name the THREE busses that forms part of the system bus in a
                     microcontroller.                                                     (3)

        6.6.3        State TWO advantages of synchronous communication when
                     compared to asynchronous communication.                              (2)

        6.6.4        State TWO disadvantages of parallel communication when
                     compared to serial communication.                                    (2)

 6.7    Draw a flow diagram for a monostable device that has only one stable state.
        The program switches the output on and off every 5 seconds and then returns
        to the original state.                                                          (10)

Copyright reserved                                                           Please turn over

                              Hosted by www.ecexams.co.za.

### Page 12

Downloaded from hlayiso.com
 12                    ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS             (EC/SEPTEMBER 2024)

 6.8    Refer to communication in a microcontroller and answer the questions that
        follow.

        6.8.1        Draw the block diagram of a microcontroller, clearly indicating the
                     THREE system buses.                                                      (6)

        6.8.2        Define the term interface.                                               (1)

 6.9    List THREE types of registers that are found in the central processing unit
        (CPU) of the microcontroller.                                                        (3)
                                                                                            [50]

                                                                              TOTAL:         200

Copyright reserved                                                                Please turn over

                              Hosted by www.ecexams.co.za.

### Page 13

Downloaded from hlayiso.com
 (EC/SEPTEMBER 2024)                   ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS          13

 FORMULA SHEET

 SWITCHING CIRCUITS

                     VOUT         R
 1.    Gain AV =             = - (R f ) inverting operational amplifier
                       VIN        in

                     VOUT             R
 2.    Gain AV =             = 1+ (R f ) non- inverting operational amplifier
                       VIN             in

                             R
 3.    VOUT = VIN × (- R f ) inverting amplifier
                             in

 4.    VOUT = -(V1 +V2 +V3 ) summing up op-amp

              1
 5.    fr = 2π√LC

              1
 6.    f = 2π√6RC

Copyright reserved                                                              Please turn over

                                  Hosted by www.ecexams.co.za.

### Page 14

Downloaded from hlayiso.com
 14                  ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS   (EC/SEPTEMBER 2024)

 LEARNER’S NAME:

 QUESTION 5: DIGITAL AND SEQUENTIAL DEVICES

 ANSWER SHEET 5.4.1

                                    FIGURE 5.4.1

Copyright reserved                                                    Please turn over

                          Hosted by www.ecexams.co.za.

## Related documents

- [ELEC TECH GR12 MEMO SEPT2024 Power Systems English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-english/bea78337-b137-406a-9b4a-c6e631a84c9d) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Electronics English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-electronics-english/c80784c8-a9c8-49f8-b740-a29558fe2de9) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-digital-english/cb603860-b00d-40c2-a36b-aa5e97b7d1e5) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH QP SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-qp-sept2023-electronics-english/867c1cd7-df12-484d-93b7-8812de59d0db) — Electrical Technology · QP · 2023 · Eng
- [ELEC TECH GR12 QP SEPT2022 Power English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2022-power-english/5dde0506-b8db-4a28-a65d-02c30160901e) — Electrical Technology · QP · 2022 · Eng
- [ELEC TECH GR12 QP SEPT2022 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2022-digital-english/924ce4d5-b0c3-4149-a3f9-e96ddcf13df1) — Electrical Technology · QP · 2022 · Eng

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [ELECTRIC TECH (Digital) MEMO GR12 SEPT 2025 ENG watermark](https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d) — Memo · 2025 · Eng
- [Electrical Technology P1 (Electronics) (English) June 2025 Possible Answers](https://www.hlayiso.com/library/electrical-technology-p1-electronics-english-june-2025-possible-answers/4302563e-89b7-4f54-8a21-63b2020e985f) — Memo · 2025 · Eng
- [Electrical Technology Nov 2025 (Digital) MG Afr](https://www.hlayiso.com/library/grade-12-electrical-technology-2025-nsc-november-exam-memorandum/3b862a0c-6a87-4296-b5b6-09b072c7d1e9) — Memo · 2025 · Afr
- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Memo · 2023 · Eng
- [ELEC TECH MEMO SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-electronics-english/5630ca3e-e352-4f96-81d0-64ec0103c0e9) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
