# Electrical Technology Grade 12 Eastern Cape Prelim 2024 QP

> Grade 12 Electrical Technology question paper from the Eastern Cape Prelim Exam 2024 (English), 17 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-electronics-english/96737d50-58d8-4c99-9fdb-bbbe73ad8146
- Updated: 2026-09-27
- Subject: Electrical Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2024
- Exam period: Eastern Cape Prelim Exam
- Curriculum: CAPS
- Pages: 17

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 Eastern Cape Prelim 2024 QP](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-electronics-english/96737d50-58d8-4c99-9fdb-bbbe73ad8146)

## About this document

Electrical Technology · Grade 12 · Eastern Cape Prelim Exam · 2024 · English. Question paper, 17 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                NATIONAL
                           SENIOR CERTIFICATE

                                 GRADE 12

                            SEPTEMBER 2024

    ELECTRICAL TECHNOLOGY: ELECTRONICS

MARKS:   200

TIME:    3 hours

                   This question paper consists of 17 pages, including
                   a 1-page answer sheet and a 2-page formula sheet.

                          Hosted by www.ecexams.co.za.

### Page 2

Downloaded from hlayiso.com
2                        ELECTRICAL TECHNOLOGY: ELECTRONICS              (EC/SEPTEMBER 2024)

INSTRUCTIONS AND INFORMATION

1.      This question paper consists of SIX questions.

2.      Sketches and diagrams must be large, neat and fully labelled.

3.      Show ALL calculations and round off answer correctly to TWO decimal
        places.

4.      Number the answers correctly according to the numbering system used in
        this question paper.

5.      You may use a non-programmable calculator.

6.      Show the units for ALL answers of calculations.

7.      A formula sheet is provided at the end of this question paper.

8.      Write neatly and legibly.

Copyright reserved                                                          Please turn over

                           Hosted by www.ecexams.co.za.

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)             ELECTRICAL TECHNOLOGY: ELECTRONICS                                3

QUESTION 1: MULTIPLE-CHOICE QUESTIONS

Various options are given as possible answers to the following questions. Choose the
answer and write only the letter (A–D) next to the question numbers (1.1 to 1.15) in
the ANSWER BOOK, for example 1.16 D.

1.1    The purpose of the Occupational Health and Safety Act is to …

       A     provide for the health and safety of persons at work.
       B     provide for the health and safety of persons at home.
       C     prevent wear and tear on machinery.
       D     prevent workers from using machinery.                                               (1)

1.2    The reference of a phasor diagram for a series RLC circuit is …

       A     apparent power.
       B     resonate frequency.
       C     current.
       D     voltage.                                                                            (1)

1.3    In a pure capacitive circuit, the capacitive reactance is … to the frequency.

       A     proportional
       B     equal
       C     indirectly proportional
       D     all of the above                                                                    (1)

1.4    Which ONE of the following are NOT true regarding a series RLC circuit at
       resonance?

       A     The capacitive reactance is equal to the inductive reactance.
       B     The current is 0 A.
       C     The resistance of the circuit is equal to the impedance of the circuit.
       D     The phase angle is 0˚.                                                              (1)

1.5    The most important feature of a FET is …

       A     the ability of its input gate voltage to control output drain current.
       B     the ability of its input gate current to control the output drain voltage.
       C     the ability of its input gate voltage to control its output drain voltage.
       D     the ability of its input gate current to control its output drain current.          (1)

1.6    Pin 3 of a 741 op-amp is …

       A     inverting input.
       B     negative supply voltage.
       C     non-inverting input.
       D     offset null.                                                                        (1)

Copyright reserved                                                                  Please turn over

                            Hosted by www.ecexams.co.za.

### Page 4

Downloaded from hlayiso.com
4                        ELECTRICAL TECHNOLOGY: ELECTRONICS                (EC/SEPTEMBER 2024)

1.7   Which ONE of the following is NOT a characteristic of an ideal op-amp?

      A      The ideal op-amp has infinite gain.
      B      The input impedance of an ideal op-amp is almost non existing low.
      C      The output impedance is extremely low, between 50 Ω and 100 Ω.
      D      The ideal op-amp will have a very wide bandwidth in order to amplify
             almost any frequency signal.                                                  (1)

1.8   An op-amp differentiator with a triangular input waveform, will always have a(n)
      … output.

      A      square wave
      B      non inverted sine wave
      C      inverted sine wave
      D      sawtooth wave                                                                 (1)

1.9   With reference to FIGURE 1.9 below, the function of R1 is …

                                         FIGURE 1.9

      A      to protect the LED from over current.
      B      to protect the 555 timer IC from over current.
      C      a pull-up resistor to prevent the voltage from floating.
      D      a pull-down resistor to prevent the voltage from floating.                   (1)

Copyright reserved                                                            Please turn over

                            Hosted by www.ecexams.co.za.

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)               ELECTRICAL TECHNOLOGY: ELECTRONICS                             5

1.10    With reference to FIGURE 1.10 below, the function of C1 is …

                                          FIGURE 1.10

        A       to allow only negative signals to pass and block positive signals.
        B       to allow only positive signals to pass and block negative signals.
        C       to allow AC signals to pass and block DC signals.
        D       to allow DC signals to pass and block AC signals.                             (1)

1.11    The operating voltage range of the 555 timer IC is …

        A       0 V to +20 V.
        B       +5 V to +15 V.
        C       -15 V to +15 V.
        D       +5 V to +9 V.                                                                 (1)

1.12    In a class A biasing of an amplifier, the Q point is chosen to lie …

        A       right at the bottom of the load line right at the cut-off point.
        B       just within the active operating region of the amplifier.
        C       right down below the cut-off region of the amplifier.
        D       in the centre of the active region of the amplifier.                          (1)

Copyright reserved                                                                 Please turn over

                             Hosted by www.ecexams.co.za.

### Page 6

Downloaded from hlayiso.com
6                          ELECTRICAL TECHNOLOGY: ELECTRONICS             (EC/SEPTEMBER 2024)

1.13    Identify the type of amplifier circuit shown by FIGURE 1.13.

                                       FIGURE 1.13

        A     Resistor capacitor coupled amplifier
        B     Push-pull amplifier
        C     Transformer coupled amplifier
        D     Radio frequency (RF) amplifier                                              (1)

1.14    Which ONE of the following is NOT an application of a RC coupled amplifier?

        A     Servo motor amplifier
        B     RF communications
        C     Public address systems as pre-amplifiers
        D     Optical fibre communications                                                (1)

1.15    The output waveform generated by a Colpitts oscillator will be a … wave.

        A     sawtooth
        B     sinusoidal
        C     triangular
        D     square                                                                     (1)
                                                                                        [15]

Copyright reserved                                                           Please turn over

                             Hosted by www.ecexams.co.za.

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)            ELECTRICAL TECHNOLOGY: ELECTRONICS                              7

QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

2.1     Describe how teamwork in a workshop environment improves work ethics.                 (2)

2.2     Horseplay in a workshop is often said to be an unsafe act. Explain why this
        statement is true.                                                                    (2)

2.3     Give ONE example of an unsafe condition found in a workshop.                          (1)

2.4     Name ONE human right with reference to work.                                          (1)

2.5     Name TWO categories of dangerous practices which you could encounter in
        an electrical workshop.                                                               (2)

2.6     Explain what the concept of quantitative risk analysis entails.                      (2)
                                                                                            [10]

QUESTION 3: RLC CIRCUITS

3.1   Define the following terms with reference to RLC circuits:

      3.1.1     Phase Angle Ø                                                                 (2)

      3.1.2     Resonance                                                                     (2)

3.2   List TWO factors that will influence the capacitive reactance (XC) of a RLC
      circuit.                                                                                (2)

3.3   Explain why a change of frequency in a RLC circuit will have no influence on
      the resistance value of the circuit.                                                    (2)

3.4   Name THREE conditions that are met during resonance with reference to a
      parallel RLC circuit.                                                                   (3)

3.5   A coil has an inductance of 80 mH and is connected in series with a 33 μF
      capacitor and a 30 Ω resistor. The circuit is connected to a 120 V alternating
      current supply with a variable frequency.

      Calculate:

      3.5.1     Resonant frequency                                                            (3)

      3.5.2     Current at resonance                                                          (3)

      3.5.3     Voltage drop across the inductor at resonance if the inductive
                reactance is 49,24 Ω                                                          (3)

Copyright reserved                                                               Please turn over

                            Hosted by www.ecexams.co.za.

### Page 8

Downloaded from hlayiso.com
8                        ELECTRICAL TECHNOLOGY: ELECTRONICS       (EC/SEPTEMBER 2024)

3.6   A RLC phasor diagram is shown in FIGURE 3.6. Answer the questions that
      follow.

                               FIGURE 3.6: PHASOR DIAGRAM

      Calculate:

      3.6.1    Inductive reactance                                                (3)

      3.6.2    Capacitive reactance                                               (3)

      3.6.3    Total current                                                      (3)

Copyright reserved                                                   Please turn over

                           Hosted by www.ecexams.co.za.

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)             ELECTRICAL TECHNOLOGY: ELECTRONICS                          9

3.7   A RLC circuit is shown in FIGURE 3.7 below. The circuit consists of a 20 Ω
      resistor, an inductor with an inductive reactance of 30 Ω and a capacitor with a
      capacitive reactance of 40 Ω connected across a 120 V/60 Hz supply voltage.
      Answer the questions that follow.

                                  FIGURE 3.7: RLC CIRCUIT

      Calculate:

      3.7.1    The total current in the circuit                                            (3)

      3.7.2    The phase angle                                                            (3)
                                                                                         [35]

Copyright reserved                                                            Please turn over

                            Hosted by www.ecexams.co.za.

### Page 10

Downloaded from hlayiso.com
10                           ELECTRICAL TECHNOLOGY: ELECTRONICS                  (EC/SEPTEMBER 2024)

QUESTION 4: SEMICONDUCTOR DEVICES

4.1    State what the abbreviation FET stand for.                                                (1)

4.2    Unlike the BJT, the FET is a uni-polar device. Explain what is meant with this
       statement.                                                                                (2)

4.3    The cross-sectional view of an N-CHANNEL JFET is shown in FIGURE 4.3.

                     4.3.1   4.3.2      4.3.3

                                4.3.4

                                FIGURE 4.3: N-CHANNEL JFET

       Label parts 4.3.1 to 4.3.4.                                                               (4)

4.4    State the abbreviation for metal-oxide-silicon field effect transistor.                   (1)

4.5    With reference to a 741 op-amp, explain what a double-polarity voltage
       supply (split power supply) is.                                                           (4)

4.6    A 741 op-amp is connected as an inverting amplifier to provide an output
       voltage of 8,5 VAC. The value of the input resistor is 180 Ω.

       Determine the value of the feedback resistor when the input voltage is 10 mV.             (3)

Copyright reserved                                                                  Please turn over

                               Hosted by www.ecexams.co.za.

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)             ELECTRICAL TECHNOLOGY: ELECTRONICS                            11

4.7    An operational amplifier circuit is shown in FIGURE 4.7. Study the circuit
       and answer the questions that follow.

                              FIGURE 4.7: OP-AMP CIRCUIT

       4.7.1    Identify the op-amp circuit that is shown in FIGURE 4.7.                    (1)

       4.7.2    Calculate the value of resistor R2 in the circuit.                          (3)

4.8    Explain the term Common Mode Rejection Ratio with reference to an
       op-amp.                                                                              (4)

4.9    Explain the use of the 741 op-amp as a buffer amplifier.                             (3)

4.10   Explain the principle of operation of the trigger pin (Pin 2) with reference to
       the 555-timer.                                                                       (3)

4.11   The 555-timer basically consists of two primary building blocks, two
       comparators and one S/R flip flop. Explain the principle of operation of the
       comparator.                                                                          (4)

4.12   Explain the function of the three 5 kΩ resistors that are connected internally
       in series between terminals 1 and 8 of the 555-timer.                                (4)

4.13   Discuss the operation of the unijunction transistor (UJT) as an electronic
       component.                                                                           (8)
                                                                                           [45]

Copyright reserved                                                               Please turn over

                            Hosted by www.ecexams.co.za.

### Page 12

Downloaded from hlayiso.com
12                       ELECTRICAL TECHNOLOGY: ELECTRONICS                   (EC/SEPTEMBER 2024)

QUESTION 5: SWITCHING CIRCUITS

5.1     With reference to the THREE classes of multivibrators, answer the questions
        that follow.

        5.1.1    Explain the bistable multivibrator in terms of inputs and stable states.      (2)

        5.1.2    Explain the monostable multivibrator in terms of inputs and stable
                 states.                                                                       (2)

        5.1.3    Explain the astable multivibrator in terms of inputs and stable states.       (2)

5.2     State ONE application of the monostable multivibrator.                                 (1)

5.3     Explain the term switch bounce with reference to the action of a switch.               (2)

5.4     State the output waveform of an astable multivibrator.                                 (1)

5.5     Explain the term hysteresis.                                                           (2)

5.6     Explain FOUR applications for the Schmitt Trigger.                                     (8)

5.7     An amplifier is shown in FIGURE 5.7. Answer the questions that follow.

                            FIGURE 5.7: ELECTRONIC CIRCUIT

        5.7.1    Identify the type of electronic circuit shown in FIGURE 5.7.                  (1)

        5.7.2    State how an additional input signal can be added to the amplifier to
                 enlarge the amplifier.                                                        (1)

        5.7.3    Calculate the output voltage for the amplifier above.                         (3)

        5.7.4    Explain why the answer to QUESTION 5.7.3 will render a negative
                 answer.                                                                       (2)

5.8     Draw the fully labelled circuit diagram of a passive RC differentiator.                (4)

5.9     Draw a fully labelled typical hysteresis characteristic curve.                         (8)

5.10    Explain how you can vary the time period with reference to a monostable
        multivibrator.                                                                         (3)

5.11    Discuss the principle of operation of a dark sensor.                                  (8)
                                                                                             [50]

Copyright reserved                                                                Please turn over

                            Hosted by www.ecexams.co.za.

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)             ELECTRICAL TECHNOLOGY: ELECTRONICS                             13

QUESTION 6: AMPLIFIERS

6.1    Compare class A and class B amplifiers with reference to the following:

       6.1.1    The Q-point of the amplifiers                                                  (2)

       6.1.2    Efficiency of the amplifiers                                                   (2)

6.2    List THREE advantages of using negative feedback in amplifier circuits.                 (3)

6.3    Explain the function of a small signal amplifier.                                       (4)

6.4    Explain the term a transistor is biased with reference to amplifiers.                   (3)

6.5    State the THREE regions an amplifier operates in.                                       (3)

6.6    Explain how amplifiers are classified into the different classes.                       (1)

6.7    Study the amplifier circuit that is shown in FIGURE 6.7. Answer the questions
       that follow.

                                   FIGURE 6.7: AMPLIFIER

       6.7.1    Calculate the maximum collector current flow in the circuit.                   (3)

       6.7.2    Determine the maximum collector-emitter voltage that can develop
                across the transistor when IC = 0 A.                                           (2)

       6.7.3    Calculate the value of the base current that is applied to the transistor.     (3)

       6.7.4    Draw the direct-current load line and indicate the Q point of the circuit
                on the direct-current load line on the common-emitter output curve that
                is provided on the ANSWER SHEET QUESTION 6.7.4.                                (3)

6.8    The input signal to a resistor-capacitor-coupled amplifier is measured as
       250 mV when the output of the amplifier is 3,5 V. Calculate the gain in
       decibels of the amplifier.                                                              (4)

6.9    Discuss why decibel was introduced to measure gain.                                     (4)

Copyright reserved                                                                Please turn over

                            Hosted by www.ecexams.co.za.

### Page 14

Downloaded from hlayiso.com
14                     ELECTRICAL TECHNOLOGY: ELECTRONICS                 (EC/SEPTEMBER 2024)

6.10   Refer to FIGURE 6.10 below and fully describe the operation of a
       RC-coupled amplifier.

                       FIGURE 6.10: RC-COUPLED AMPLIFIER                                (8)
                                                                                       [45]

                                                                           TOTAL:      200

Copyright reserved                                                           Please turn over

                          Hosted by www.ecexams.co.za.

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)      ELECTRICAL TECHNOLOGY: ELECTRONICS                15

LEARNER’S NAME: _____________________________________________________

ANSWER SHEET

QUESTION 6: AMPLIFIERS

 6.7.4

Copyright reserved                                            Please turn over

                      Hosted by www.ecexams.co.za.

### Page 16

Downloaded from hlayiso.com
16                                                  ELECTRICAL TECHNOLOGY: ELECTRONICS                                       (EC/SEPTEMBER 2024)

                                                                        FORMULA SHEET
 RLC CIRCUIT                                                                SEMI-CONDUCTORS DEVICES

                                                  1                              𝑉𝑜𝑢𝑡             𝑅
 𝑋𝐿 = 2𝜋𝐹𝐿 𝑎𝑛𝑑 𝑋𝐶 =                                                         𝐴𝑉 = 𝑉𝑖𝑛 = 𝑅 𝐹
                                                                                                  𝐼𝑁
                                                2𝜋𝐹𝐶
                                                                                                           𝑅
 SERIES                                                                     𝑉𝑂𝑈𝑇 = 𝑉𝐼𝑁 = (− 𝑅 𝐹 )
                                                                                                               𝐼𝑁

 𝐼𝑇 =𝐼𝑅 =𝐼𝐶 = 𝐼𝐿                                                                          𝑅
                                                                            𝐴𝑉 = 1+𝑅 𝐹
                                                                                          𝐼𝑁

 𝑍 = √𝑅 2 + (𝑋𝐿 − 𝑋𝐶 )2                                                                                    𝑅
                                                                            𝑉𝑂𝑈𝑇 = 𝑉𝐼𝑁 (1 + 𝑅 𝐹 )
                                                                                                           𝐼𝑁
               2                                2
 𝑉𝑇 = √𝑉𝑅 + (𝑉𝐿− 𝑉𝐶 )
                                                                            𝛽𝑠𝑢𝑝𝑒𝑟 = 𝛽1 × 𝛽2

 𝑉𝐿 = 𝐼𝑋𝐿 and 𝑉𝑐 = 𝐼𝑋𝐶 and 𝑉𝑇 = 𝐼𝑍
                                                                            AMPLIFIERS
                                𝑅
          𝐶𝑂𝑆𝜃 = 𝑍                                                          𝑉𝐶𝐸 = 𝑉𝐶𝐶
                                                                                     𝑉
                                                                            𝐼𝐶𝑚𝑎𝑥 = 𝑅𝐶𝐶
                            𝑉                                                                 𝐶
          𝐶𝑂𝑆𝜃 = 𝑉𝑅                                                          ′    𝐴
                                                                            𝐴 = 1+𝛽𝐴
                                𝑇

      𝑋    𝑋        𝑉
 𝑄 = 𝑍𝐿= 𝑍𝐶 =𝑉𝐿 = 𝑉𝐶 = 𝑅 √𝐶
                                    𝑉               1       𝐿                                                       Pout
                        𝑆               𝑆
                                                                            Power Gain 𝐴𝑃 = 𝑙𝑜𝑔10 (                      )
                                                                                                                     Pin
 PARALLEL                                                                                         𝐸
                                                                            𝐴𝑉 =20 𝑙𝑜𝑔10 𝐸𝑜𝑢𝑡 dB
                                                                                                      𝑖𝑛
 1. 𝑉𝑇 = 𝑉𝑅 =𝑉𝐿 = 𝑉𝐶
                                                                                                  𝐼
                                                                            𝐴𝐼 = 20 𝑙𝑜𝑔10 𝐼𝑜𝑢𝑡
           𝑽                                        𝑉               𝑉                                 𝑖𝑛
 2. 𝐼𝑹 = 𝑹 = 𝑎𝑛𝑑 𝐼𝐿 = 𝑋 = 𝐼𝐶 = 𝑋
                                                    𝐿               𝐶
                                                                                      1
                                                                            𝐹0 = 2𝜋√𝐿 𝐶
                                                                                          𝑇
 3. 𝐼𝑇 = √𝐼𝑅 2 + (𝐼𝐿 − 𝐼𝐶 )2
                                                                                  1
                                                                            Fr =2𝜋√𝐿𝐶
                   𝐼𝑅
 4. 𝐶𝑂𝑆𝜃 =                                                                            1
                   𝐼𝑇                                                       𝐹𝑂 = 2𝜋√6 𝑅𝐶

           𝑋𝐿        𝑋                  𝑉               1       𝐿
 5. 𝑄 =            = 𝑍𝐶 = 𝑉𝐿 = 𝑅 = √𝐶
           𝑍                                𝑆

Copyright reserved                                                                                                              Please turn over

                                                            Hosted by www.ecexams.co.za.

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2024)                      ELECTRICAL TECHNOLOGY: ELECTRONICS                17

 SWITCHING CIRCUITS

                   𝑉             𝑅
1.    Gain A𝑉 = 𝑉𝑂𝑈𝑇 = − (𝑅 𝑓 ) inverting operational amplifier
                       𝐼𝑁        𝑖𝑛

                   𝑉                 𝑅
2.    Gain A𝑉 = 𝑉𝑂𝑈𝑇 = 1 + (𝑅 𝑓 ) non-inverting operational amplifier
                       𝐼𝑁             𝑖𝑛

                            𝑅
3.    𝑉𝑂𝑈𝑇 = 𝑉𝐼𝑁 × (− 𝑅 𝑓 ) inverting amplifier
                            𝑖𝑛

4.    𝑉𝑂𝑈𝑇 = −(𝑉1 + 𝑉2 + 𝑉3 ) summing up op-amp

             1
5.    𝑓𝑟 = 2𝜋√𝐿𝐶

             1
6.    𝑓 = 2𝜋√6𝑅𝐶

Copyright reserved                                                            Please turn over

                                 Hosted by www.ecexams.co.za.

## Related documents

- [ELEC TECH GR12 MEMO SEPT2024 Power Systems English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-english/bea78337-b137-406a-9b4a-c6e631a84c9d) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Electronics English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-electronics-english/c80784c8-a9c8-49f8-b740-a29558fe2de9) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-digital-english/cb603860-b00d-40c2-a36b-aa5e97b7d1e5) — Electrical Technology · Memo · 2024 · Eng
- [Electrical Technology May-June 2024 (Digital) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/2b227e9b-0513-468e-8b1a-d4df808071cd) — Electrical Technology · QP · 2024 · Eng
- [ELEC TECH QP SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-qp-sept2023-electronics-english/867c1cd7-df12-484d-93b7-8812de59d0db) — Electrical Technology · QP · 2023 · Eng
- [ELEC TECH GR12 QP SEPT2022 Power English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2022-power-english/5dde0506-b8db-4a28-a65d-02c30160901e) — Electrical Technology · QP · 2022 · Eng

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [ELECTRIC TECH (Digital) MEMO GR12 SEPT 2025 ENG watermark](https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d) — Memo · 2025 · Eng
- [Electrical Technology P1 (Electronics) (English) June 2025 Possible Answers](https://www.hlayiso.com/library/electrical-technology-p1-electronics-english-june-2025-possible-answers/4302563e-89b7-4f54-8a21-63b2020e985f) — Memo · 2025 · Eng
- [Electrical Technology Nov 2025 (Digital) MG Afr](https://www.hlayiso.com/library/grade-12-electrical-technology-2025-nsc-november-exam-memorandum/3b862a0c-6a87-4296-b5b6-09b072c7d1e9) — Memo · 2025 · Afr
- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Memo · 2023 · Eng
- [ELEC TECH MEMO SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-electronics-english/5630ca3e-e352-4f96-81d0-64ec0103c0e9) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
