# Electrical Technology Grade 12 Eastern Cape Mock 2025 Memo

> Grade 12 Electrical Technology memorandum from the Eastern Cape Mock Exam 2025 (English), 10 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d
- Updated: 2026-09-27
- Subject: Electrical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2025
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 10

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 Eastern Cape Mock 2025 Memo](https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d)

## About this document

Electrical Technology · Grade 12 · Eastern Cape Mock Exam · 2025. Memorandum, 10 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

NATIONAL
                   SENIOR CERTIFICATE

                             GRADE 12

                    SEPTEMBER 2025

               ELECTRICAL TECHNOLOGY:
                 DIGITAL ELECTRONICS
                  MARKING GUIDELINE

MARKS:   200

                 This marking guideline consists of 10 pages.

### Page 2

2                     ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS            (EC/SEPTEMBER 2025)

 INSTRUCTIONS TO MARKERS

 1.    All calculations with multiple answers imply that any relevant, acceptable answer
       should be considered.

 2.    Calculations:

       2.1    All calculations must show the formulae.

       2.2    Substitution of values must be done correctly.

       2.3    All answers MUST contain the correct unit to be considered.

       2.4    Alternative methods must be considered, provided that the correct answer
              is obtained.

       2.5    Where an incorrect answer could be carried over to the next step, the first
              answer will be deemed incorrect. However, should the incorrect answer
              be carried over correctly, the marker has to re-calculate the values, using
              the incorrect answer from the first calculation. If correctly used, the
              candidate should receive the full marks for subsequent calculations.

       2.6    Markers should consider that learners answers may deviate slightly from
              the marking guideline depending on how and where in the calculation
              rounding off was used.

 3.    This marking guideline is only a guide with model answers.

 4.    Alternative interpretations must be considered and marked on merit. However,
       this principle should be applied consistently throughout the marking session at
       ALL marking centres.

Copyright reserved                                                              Please turn over

### Page 3

(EC/SEPTEMBER 2025)          ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                       3

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS

 1.1      A ✓
 1.2      D ✓
 1.3      C ✓
 1.4      A ✓
 1.5      B ✓
 1.6      A ✓
 1.7      A ✓
 1.8      A ✓
 1.9      B✓
 1.10     A ✓
 1.11     B ✓
 1.12     D ✓
 1.13     A ✓
 1.14     D ✓
 1.15     A ✓                                                                               [15]

 QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

 2.1      • The purpose of the Occupational Health and Safety Act is to provide for
            the health and safety of:
          • Persons at work ✓
          • Persons in connection with the use of plant and machinery ✓
          • The protection of persons against hazards arising out of the activities of
            other persons at work
          • To establish an advisory council for occupational health and safety and
            related matters.                                             (Any 2 x 1)         (2)

 2.2      An occurrence of catastrophic proportions, ✓ resulting from the use of
          machinery, or activities at work. ✓                                                (2)

 2.3      2.3.1      Running could cause you to trip or collide with others. ✓ This could
                     result in injuring with nearby equipment or machinery. ✓                (2)

          2.3.2      This could cause the outlet to exceed its rated current ✓ and could
                     lead to short circuits, fires or damaged appliances. ✓                  (2)

 2.4      Faulty tools or equipment ✓
          Poor ventilation ✓
          Poor or missing guards
          Excessive noise
          Lack of knowledge of emergency procedures               (Any relevant answer)      (2)
                                                                                            [10]

Copyright reserved                                                               Please turn over

### Page 4

4                         ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS          (EC/SEPTEMBER 2025)

 QUESTION 3: SWITCHING CIRCUITS

 3.1    The time lag between cause and effect. ✓                                                (1)

 3.2
                                       Vout

                                +10V

                     -1V                      +1V
                                                    Vin

                                       -10V                                                     (4)

 3.3    Widely used in the first stages of many radio receivers. ✓
        In digital circuitry noise is often introduced into a system via switch bounce
        which can cause a number of unwanted voltage spikes to appear during
        switching-on period. ✓
        Varying input waveforms, for example a sine wave can be changed into a
        square or rectangular wave. ✓
        A signal can be successfully recovered using a Schmitt trigger even after having
        suffered severe distortion. ✓                                                           (4)

 3.4

                                                                                                (4)

 3.5    3.5.1    Mono-stable Multivibrator ✓                                                    (1)

        3.5.2    As the switch is activated it pulls pin 2 of the IC to 0 V, ✓ triggering
                 the 555.
                 This immediately re-sets the circuit, ✓ setting both the Output pin 3
                 and Discharge pin 7 ‘high’. ✓                                                  (3)

        3.5.3    When triggered, C1 charges through R1 ✓ and the time it takes to reach
                 the threshold voltage (2/3 Vcc) dictates how long the output remains
                 high. ✓                                                                        (2)

        3.5.4    𝜏 = 1,1 x R x C ✓
                 𝜏 = 1,1 x 90 000 x 0,0001 ✓
                 𝜏 = 9,9 seconds ✓                                                              (3)

        3.5.5    De-bouncing ✓
                 Varying the time period ✓                                                      (2)

Copyright reserved                                                                 Please turn over

### Page 5

(EC/SEPTEMBER 2025)        ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                          5

 3.6    3.6.1    This means that the time constant (RC) component values are large. ✓          (1)

        3.6.2    In this circuit with a long time constant, a square wave would produce
                 a long, slow triangular wave at its output.                                   (1)

 3.7    The less light on the LDR, ✓ the higher the resistance. ✓
        The more light on the LDR, ✓ the lower the resistance. ✓                               (4)

 3.8

                                                                                               (8)

 3.9    3.9.1    By adding another input resistor to the summing amplifier input. ✓            (1)

        3.9.2

                                                                                               (4)

        3.9.3    It is negative because the inputs are fed into the inverting input, ✓ which
                 will cause the output to be 180° out of phase. ✓                              (2)

 3.10 Switch bounce can be eliminated by using a monostable multivibrator circuit to
      control the output. ✓                                                                    (1)

 3.11

                                                                                                (4)
                                                                                               [50]

Copyright reserved                                                                Please turn over

### Page 6

6                   ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                (EC/SEPTEMBER 2025)

 QUESTION 4: SEMICONDUCTOR DEVICES

 4.1

                                    Drawing correct ✓
                                    Inputs and Output labelled correct ✓
                                    Positive and negative supplies labelled correct ✓
                                                                                               (3)

 4.2 Input stage (Differential amplifier) ✓
     Intermediate stage (High gain differential amplifier) ✓
     Common Collector (Darlington Pair) output stage ✓                                         (3)

 4.3 It is an active low trigger ✓
     When the voltage on pin 2 is less than ⅓ of the supply, the output goes high ✓
     When the voltage on pin 2 is higher than ⅔ of the supply, the output will go
     low ✓
     If connected to ground, the output will go ‘high’ and remain ‘high’ ✓                     (4)

 4.4 The op-amp should be able to amplify any input of any frequency, from 0 Hz
     through to radio frequency and higher. ✓ This is not practical and the gain drops
     at higher frequencies. ✓ This is due to internal capacitances in the op-amp’s
     chip. ✓                                                                                   (3)

 4.5 4.5.1

                                                                                               (3)

       4.5.2

                                                                                               (3)

       4.5.3    If the value of the feedback resistor is decreased the gain of the amplifier
                will decrease causing the output voltage to decrease. ✓                         (1)
                                                                                               [20]

Copyright reserved                                                                Please turn over

### Page 7

(EC/SEPTEMBER 2025)        ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                         7

 QUESTION 5: DIGITAL AND SEQUENTIAL DEVICES

 5.1 Polarisation ✓                                                                           (1)

 5.2 The anodes of all 8 LEDs are connected together ✓ on the positive voltage
     rail ✓                                                                                   (2)

 5.3 5.3.1

                                                                                              (4)

       5.3.2

                                                                                              (4)

 5.4 5.4.1      D-Type Latch ✓ D Flip-Flop                                                    (1)

       5.4.2    In this circuit the R input has been replaced by the compliment
                (inversion) of the S input.
                The S input has been renamed to D input. ✓
                If the clock input is low, the D-Latch will not respond to an input signal.
                Once the clock input goes high the output will follow the D input. As the
                second input is always the inverse of the D input there will thus never be
                an illegal state. ✓                                                           (2)

       5.4.3    Shift Registers ✓
                Storage Registers ✓                                                           (2)

 5.5 A synchronous counter uses a common clock pulse ✓ that tries to clock all the
     various JK flip-flops simultaneously. ✓

       An asynchronous counter has a clock pulse only on the first JK latch ✓ that
       serves as the LSB. The output of each JK latch is set as the clock pulse for the
       next JK latch. ✓                                                                       (4)

 5.6 Serial-in: Parallel-out shift register (SIPO) ✓
     Serial-in: Serial-out shift register (SISO) ✓
     Parallel-in: Parallel-out shift register (PIPO)                                          (2)

Copyright reserved                                                               Please turn over

### Page 8

8                     ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS            (EC/SEPTEMBER 2025)

 5.7    All four bits of the input will simultaneously ✓ be loaded to the input of all the
        flip-flops. ✓
        After one clock pulse each flip-flop will shift its input to its output. ✓
        This process will repeat itself for four clock pulses ✓ so that the complete 4-bit
        input is available at the output.                                                    (4)

 5.8    An encoder is designed to accept input data in decimal form ✓ and to convert
        this information into its binary form. ✓

        A decoder is designed to convert a binary code into a recognizable decimal
        form, ✓ either as a digit or as a character. ✓                                       (4)

 5.9    Frequency divider ✓
        Decade counter ✓
        Binary coded decimal counter ✓                                                       (3)

 5.10   They are slower ✓ due to the propagation delay through the additional gates in
        the system. ✓                                                                        (2)

 5.11   5.11.1       Encoder ✓                                                               (1)

        5.11.2

                                                                                             (5)

 5.12
        5.12.1

                                                                                             (8)

        5.12.2       The circuit in FIGURE 5.12 is synchronous. ✓                             (1)
                                                                                             [50]

Copyright reserved                                                              Please turn over

### Page 9

(EC/SEPTEMBER 2025)          ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                      9

 QUESTION 6: MICROCONTROLLERS

 6.1    Microcontrollers are used in industrial control devices:
        • Industrial instrumentation ✓
        • Monitoring ✓
        • Process control
        • Cooling systems                                                    (Any 2 x 1)     (2)

 6.2    6.2.1    Microcontroller ✓                                                           (1)

        6.2.2    RAM (Random Access memory) ✓                                                (1)

        6.2.3    Read Only Memory ✓                                                          (1)

 6.3    The Current Instruction Register (CIR) splits the instruction into two parts. ✓
        One part is decoded by the control unit ready for execution, ✓ the other part is
        the address of the data stored that needs to be used together with that
        instruction. ✓                                                                       (3)

 6.4    6.4.1    –200 mV = 1 ✓
                 200 mV = 0 ✓                                                                (2)

        6.4.2    To connect the following to the main frame:
                 Point of sale terminals ✓
                 Metering instruments ✓
                 Large special automated machines ✓                                          (3)

        6.4.3    Simplex data communication is where all data and information travels
                 in only one direction ✓ from transmitter to receiver. ✓

                 Half duplex communication is where the two devices take turn in
                 communicating, ✓ one after the other. ✓                                     (4)

 6.5    6.5.1        • Control bus ✓
                     • Data bus ✓
                     • Address bus ✓                                                         (3)

        6.5.2    • Supports a higher data transfer rate. ✓
                 • The sender and the receiver use the same clock pulse. ✓                   (2)

        6.5.3    • Requires more communication lines. ✓
                 • Requires more space. ✓
                 • Requires larger connections.                                              (2)

 6.6    6.6.1    A program is a sequence of instructions ✓ that tell a computer how to
                 do a task. ✓                                                                (2)

        6.6.2    A flowchart is a pictorial version of an algorithm ✓ and illustrates the
                 flow of a program. ✓                                                        (2)

        6.6.3    An algorithm is a precise set of procedures to be followed ✓ to solve a
                 problem. ✓                                                                  (2)

Copyright reserved                                                              Please turn over

### Page 10

10                  ELECTRICAL TECHNOLOGY: DIGITAL ELECTRONICS                (EC/SEPTEMBER 2025)

 6.7    In legal data flow the data lines will follow one another after a specific action ✓
        and they will not cross one another or move against the other flow. ✓
        In illegal data flow the data lines will just end without reaching a function. ✓ The
        data lines may also move against the flow of other lines or the data lines may
        cross other data lines. ✓                                                              (4)
 6.8    6.8.1

                                                                                               (9)

        6.8.2    Shared boundary ✓ across which two separate components of a
                 computer system exchanges information. ✓                                      (2)
 6.9

                                                                                               (10)
                                                                                               [55]
                                                                                 TOTAL:        200

Copyright reserved                                                                Please turn over

## Related documents

- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Electrical Technology · Memo · 2023 · Eng
- [ELEC TECH MEMO SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-electronics-english/5630ca3e-e352-4f96-81d0-64ec0103c0e9) — Electrical Technology · Memo · 2023 · Eng
- [ELEC TECH GR12 MEMO SEPT2022 Power English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2022-power-english-1/1304f4fd-377a-40b4-8abd-4e3860f4fd0d) — Electrical Technology · Memo · 2022 · Eng
- [ELEC TECH GR12 MEMO SEPT2022 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2022-digital-english/d9f4d172-a252-4eb9-b51b-6936353fe4e6) — Electrical Technology · Memo · 2022 · Eng
- [ELEC TECH GR12 MEMO SEPT2022 Electronics English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2022-electronics-english/8e5f2a9b-1a0d-480e-8c17-93268b5cebfe) — Electrical Technology · Memo · 2022 · Eng
- [ELEC TECH GR12 MEMO SEPT2020 Afrikaans Power](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2020-afrikaans-power/3bf820c8-f427-4b77-acb6-9d1d1c1e44db) — Electrical Technology · Memo · 2020 · Afr

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [Electrical Technology (Power Systems) (English) June 2025 Question Paper](https://www.hlayiso.com/library/electrical-technology-power-systems-english-june-2025-question-paper/5422e67a-03a4-4202-ba9b-1b9ec9872537) — QP · 2025 · Eng
- [ELEC TECH GR12 QP SEPT2024 Electronics Afrikaans](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-electronics-afrikaans/6fc3719e-6eab-469e-baf1-ca1645c8ebad) — QP · 2024 · Afr
- [ELEC TECH GR12 QP SEPT2024 Power Systems Afrikaans](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-power-systems-afrikaans/928e510b-68c2-4670-a7c7-fe20b388befb) — QP · 2024 · Afr
- [ELEC TECH GR12 QP SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-digital-english/9fcfef2b-6d5e-4601-853a-24a2a3993617) — QP · 2024 · Eng
- [Electrical Technology Nov 2024 (Electronics) Eng](https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-eng/870e3d22-85e9-42bd-890f-3ef1fd3333cf) — QP · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
