# Electrical Technology Grade 12 November 2024 NSC QP (Eng)

> Grade 12 Electrical Technology question paper from the November 2024 NSC (English), 29 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-eng/870e3d22-85e9-42bd-890f-3ef1fd3333cf
- Updated: 2026-09-27
- Subject: Electrical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 29

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 November 2024 NSC QP (Eng)](https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-eng/870e3d22-85e9-42bd-890f-3ef1fd3333cf)

## About this document

Electrical Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 29 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Confidential

                                 GRAAD 12

                                 NATIONAL
                            SENIOR CERTIFICATE

                                    GRADE 12

                     ELECTRICAL TECHNOLOGY: ELECTRONICS

                                 NOVEMBER 2024

MARKS: 200

TIME: 3 hours

        This question paper consists of 23 pages, a 1-page formula sheet and
                              a 5-page answer sheet.

Copyright reserved                                                   Please turn over

### Page 2

Electrical Technology: Electronics             2                           DBE/November 2024
                                         NSC Confidential

INSTRUCTIONS AND INFORMATION

1.        This question paper consists of SIX questions.

2.        Answer ALL the questions.

3.        Answer the following questions on the attached ANSWER SHEETS:

          QUESTIONS 5.4.4, 5.5.1 and 5.9.2
          QUESTIONS 6.2.4, 6.5.3 and 6.6.3

4.        Write your centre number and examination number on every ANSWER
          SHEET and hand them in with your ANSWER BOOK, whether you have used
          them or not.

5.        Sketches and diagrams must be large, neat and FULLY LABELLED.

6.        Show ALL calculations and round off answers correctly to TWO decimal
          places.

7.        Number the answers correctly according to the numbering system used in this
          question paper.

8.        You may use a non-programmable calculator.

9.        Calculations must include:

          9.1        Formulae and manipulations where needed

          9.2        Correct replacement of values

          9.3        Correct answer and relevant units where applicable

10.       A formula sheet is attached at the end of this question paper.

11.       Write neatly and legibly.

Copyright reserved                                                             Please turn over

### Page 3

Electrical Technology: Electronics                 3                         DBE/November 2024
                                             NSC Confidential

QUESTION 1: MULTIPLE-CHOICE QUESTIONS

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers (1.1 to 1.15) in
the ANSWER BOOK, e.g. 1.16 D.          Nov

1.1       A disastrous event, resulting from the use of plant and machinery, or from
          activities at a workplace, is known as a/an …

          A      minor incident.
          B      major incident.
          C      accident.
          D      risk.                                                                               (1)

1.2       The impedance in a RLC series circuit, is minimum when the …

          A      inductive reactance equals the capacitive reactance.
          B      inductive reactance is greater than the capacitive reactance.
          C      capacitive reactance is greater than the inductive reactance.                       (1)
          D      resistance is maximum.

1.3       In a pure capacitive circuit that is connected to an AC supply, the …

          A      voltage leads the current by 90°.
          B      current leads the voltage by 90°.
          C      voltage and current are in phase.
          D      current leads the voltage by 180°.                                                  (1)

1.4       The quality factor of an RLC parallel circuit is … to the bandwidth.

          A      inversely proportional
          B      directly proportional
          C      equal
          D      not related                                                                         (1)

1.5       One advantage the field-effect transistor (FET) has over the bipolar junction
          transistor (BJT) is …

          A      a low input impedance.
          B      the amplification of large signal voltages at the input stage of amplifiers.
          C      a high input impedance.
          D      that it draws a large amount of input current.                                      (1)

1.6       A … is a three-terminal semiconductor device that can operate in the negative
          resistance region of its characteristic curve.

          A      Darlington transistor
          B      unijunction transistor
          C      bipolar junction transistor
          D      junction-field effect transistor                                                    (1)

Copyright reserved                                                                Please turn over

### Page 4

Electrical Technology: Electronics             4                           DBE/November 2024
                                         NSC Confidential

1.7       A … is a characteristic of an ideal operational amplifier.

          A      low input impedance
          B      low voltage gain
          C      limited bandwidth
          D      low output impedance                                                               (1)

1.8       The gain of the … operational amplifier will be 2 if the values of the feedback
          resistor and the input resistor(s) are the same.

          A      integrator
          B      non-inverting
          C      inverting
          D      summing                                                                            (1)

1.9       The … multivibrator circuit produces a continuous square wave output without
          any external trigger.

          A      monostable
          B      astable
          C      bistable
          D      Schmitt trigger                                                                    (1)

1.10      The output of a 555 monostable multivibrator circuit … after a trigger pulse is
          applied.

          A      remains stable until power is turned off
          B      switches to the other stable state and remains there indefinitely
          C      remains in the unstable state for a fixed period before returning to its
                 stable state
          D      continually changes between +VCC and -VCC.                                         (1)

1.11      The primary function of a summing operational amplifier circuit is to …

          A      amplify only the largest signal of multiple input signals.
          B      subtract multiple input signals to receive one output signal.
          C      add multiple input signals to receive one output signal.
          D      compare multiple input signals to receive one output signal.                       (1)

1.12      The output voltage of an integrator operational amplifier … when a constant
          long and large input voltage is applied.

          A      is constant
          B      increases linearly
          C      decreases linearly
          D      oscillates between positive and negative values                                    (1)

Copyright reserved                                                               Please turn over

### Page 5

Electrical Technology: Electronics              5                         DBE/November 2024
                                          NSC Confidential

1.13      The primary purpose of the coupling capacitors in an RC coupled amplifier is
          to …

          A      provide DC to pass through.
          B      block DC and allow AC signals to pass.
          C      increase voltage.
          D      allow DC signals to pass and to block AC signals.                                (1)

1.14      The disadvantage of a push-pull amplifier is …

          A      frequency distortion.
          B      amplitude distortion.
          C      phase distortion.
          D      cross-over distortion.                                                           (1)

1.15      The transistor in a class C amplifier conducts for … of the input cycle.

          A      more than 180º
          B      more than 180º but less than 360º
          C      less than 180º
          D      more than 360º                                                                   (1)
                                                                                                  [15]

QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

2.1       Define the term workplace with reference to the Occupational Health and
          Safety Act, 1993 (Act 85 of 1993).                                                      (2)

2.2       Name TWO human rights in the workplace.                                                 (2)

2.3       Explain why poor ventilation is an unsafe condition in a workshop.                      (2)

2.4       State TWO types of victimisation by an employer that are forbidden.                     (2)

2.5       Explain why a person should not interfere with equipment in the workshop
          that is provided for safety.                                                            (2)
                                                                                                  [10]

Copyright reserved                                                             Please turn over

### Page 6

Electrical Technology: Electronics              6                           DBE/November 2024
                                          NSC Confidential

QUESTION 3: RLC CIRCUITS

3.1       Explain the following terms with reference to RLC circuits:

          3.1.1        Inductive reactance                                                         (2)

          3.1.2        Bandwidth                                                                   (2)

3.2       FIGURE 3.2 below shows an RLC series circuit with a variable frequency
          supply. Answer the questions that follow.

                                     R       XL = 150         XC = 113,6

                                             VL = 3,45 V      VC = 2,61 V

                                              2,5 V/50 Hz

                                     FIGURE 3.2: RLC SERIES CIRCUIT

          Given:

          XL           = 150 Ω
          XC           = 113,6 Ω
          VT           = 2,5 V
          VL           = 3,45 V
          VC           = 2,61 V

          3.2.1        State whether the circuit represented in FIGURE 3.2 has a leading
                       or a lagging power factor.                                                  (1)

          3.2.2        Calculate the current through the inductor.                                 (3)

          3.2.3        Calculate the value of the inductor.                                        (3)

          3.2.4        Calculate the value of resistor R if the impedance Z = 106,42 Ω.            (3)

Copyright reserved                                                              Please turn over

### Page 7

Electrical Technology: Electronics               7                                      DBE/November 2024
                                           NSC Confidential

          3.2.5        Complete the phasor diagram in FIGURE 3.2.5 below in your
                       ANSWER BOOK.

                                                              IT         VR

                                          FIGURE 3.2.5: PHASOR DIAGRAM                                         (4)

          3.2.6        After decreasing the frequency, the current increased slightly.
                       Explain why this happened.                                                              (3)

3.3       FIGURE 3.3 below shows an RLC parallel circuit and its impedance vs
          frequency response curve. Answer the questions that follow.

                                     IT          IR                 IL               IC
                                                                                   9,2 A
                       230 V                       R                     XL
                       50 Hz                                                            C
                                                  60 Ω                  25 Ω

                                 Z

                                                 f1    fr          f2          f (Hz)

                     FIGURE 3.3: RLC PARALLEL CIRCUIT AND FREQUENCY
                                    RESPONSE CURVE

Copyright reserved                                                                          Please turn over

### Page 8

Electrical Technology: Electronics              8                         DBE/November 2024
                                          NSC Confidential

          Given:

          VT       =   230 V
          IC       =   9,2 A
          R        =   60 Ω
          XL       =   25 Ω
          f        =   50 Hz

          3.3.1        Calculate the current through the resistor.                                (3)

          3.3.2        Calculate the capacitive reactance.                                        (3)

          3.3.3        Determine the total current. Give a reason for your answer.                (2)

          3.3.4        Calculate the Q-factor of the circuit.                                     (3)

          3.3.5        Calculate the bandwidth of the circuit.                                    (3)
                                                                                                  [35]

Copyright reserved                                                             Please turn over

### Page 9

Electrical Technology: Electronics             9                            DBE/November 2024
                                         NSC Confidential

QUESTION 4: SEMICONDUCTOR DEVICES

4.1       Identify the MOSFET represented by the symbol in FIGURE 4.1 below.

                                                             D

                                            G

                                                             S

                                        FIGURE 4.1: MOSFET                                         (2)

4.2       Refer to FIGURE 4.2 below and answer the questions that follow.

                                                            IDS
                                                    D

                                        G
                                                P       N         P   VDS

                                 VGS

                                                    S

                           FIGURE 4.2: CONSTRUCTION OF A JFET

          4.2.1        Describe how the pinching state is reached in FIGURE 4.2 above.             (3)

          4.2.2        Explain why the junction field-effect transistor (JFET) has a high
                       input resistance compared to the bipolar junction transistor (BJT).         (3)

Copyright reserved                                                              Please turn over

### Page 10

Electrical Technology: Electronics              10                              DBE/November 2024
                                           NSC Confidential

4.3       Refer to FIGURE 4.3 below and answer the questions that follow.

                            ID

                                       A                      B

                                                                          ID

                                                                    VGS

                                                                          VGS

                           FIGURE 4.3: MOSFET CHARACTERISTIC CURVE

          4.3.1        Identify the MOSFET characteristic curve in FIGURE 4.3 above.                   (1)

          4.3.2        Label the regions at A and B.                                                   (2)

          4.3.3        Briefly describe the relationship between the gate-source voltage
                       (VGS) and the drain current (ID), with reference to the characteristic
                       curve.                                                                          (4)

          4.3.4        State TWO applications of a metal-oxide-semiconductor field-effect
                       transistor (MOSFET).                                                            (2)

4.4       State the difference between the junction field-effect transistor (JFET) and the
          metal-oxide-semiconductor field-effect transistor (MOSFET), with reference to
          their modes of operation.                                                                    (1)

Copyright reserved                                                                  Please turn over

### Page 11

Electrical Technology: Electronics                    11                  DBE/November 2024
                                                 NSC Confidential

4.5       FIGURE 4.5 below shows the circuit diagram of a UJT as a saw-tooth
          generator. Answer the questions that follow.

                                                                              +VBB

                              R1                        R2

                                                                B2

                                                  E

                                                                    B1

                             C
                                                        R3

                                                                              0V

                             FIGURE 4.5: UJT AS A SAW-TOOTH GENERATOR

          4.5.1        Name the polarity of the pulse that would be produced across B1.          (1)

          4.5.2        Briefly describe how the UJT reaches the valley point during its
                       operation.                                                                (2)

          4.5.3        State the difference between a unijunction transistor (UJT) and a
                       bipolar junction transistor (BJT), with reference to the following:

                       (a)       Construction                                                    (2)

                       (b)       Amplification                                                   (2)

Copyright reserved                                                            Please turn over

### Page 12

Electrical Technology: Electronics                  12                                DBE/November 2024
                                               NSC Confidential

4.6       Refer to FIGURE 4.6 below and answer the questions that follow.

                                                  +V                                            +V

               V2            +                                 V1          _
            (positive)                                      (positive)
                             _                                             +
                                        VOUT                                             VOUT
                                 -V                                            -V
                                                  0V                                            0V
                           FIGURE A                                        FIGURE B

                           FIGURE 4.6: OPERATIONAL AMPLIFIERS

          4.6.1          Determine the state of the output voltages in FIGURE A and
                         FIGURE B.                                                                           (2)

          4.6.2          State TWO advantages of an operational amplifier.                                   (2)

          4.6.3          Explain the term common mode rejection ratio with reference to
                         operational amplifier characteristics.                                              (1)

4.7       FIGURE 4.7 below is an operational amplifier with an input signal voltage of
          2 mV, a feedback resistor RF = 4,7 kΩ, non-inverting resistor R1 = 22 kΩ and
          input resistor RIN = 470 Ω. Answer the questions that follow.

                                                          RF = 4,7 k Ω

                                      RIN = 470 Ω                 +9 V
                                                             _

                                                             +
                   VIN = 2 mV                                     -- 9 V
                                                                                      VOUT
                                      R1 = 22 kΩ

                                                                                        0V

                             FIGURE 4.7: OPERATIONAL AMPLIFIER

          Given:

          VIN     = 2 mV
          RIN     = 470 Ω
          RF      = 4,7 kΩ
          R1      = 22 kΩ

Copyright reserved                                                                        Please turn over

### Page 13

Electrical Technology: Electronics               13                                DBE/November 2024
                                            NSC Confidential

          4.7.1        Name the type of feedback used in FIGURE 4.7                                       (1)
          4.7.2        Calculate the gain.                                                                (3)
          4.7.3        Calculate the output voltage.                                                      (3)
          4.7.4        Explain why operational amplifiers require dual power supplies to
                       operate.                                                                           (2)
4.8       FIGURE 4.8 below shows the internal circuit diagram of a 555 IC. Answer the
          questions that follow.

                      +Vcc                                                            Control
                     supply               Discharge            Threshold              Voltage

                        8                    7                     6                     5

                5 kΩ
                                                     -
                                                         C1
                                                     +                                         T2

                                                                   Flip-flop
                                                               R               Q

                5 kΩ                                           S               Q

                                                     -
                                                         C2
                                                     +
                5 kΩ

                                     T1

                       1                     2                     3                      4
                     Ground                Trigger              Output                 Reset

                            FIGURE 4.8: INTERNAL LAYOUT OF A 555 IC
          4.8.1        State ONE industrial application where the 555 IC is used as a
                       timing device.                                                                     (1)

          4.8.2        Explain how the NPN transistor (T1) can be turned ON when the
                       555 IC is connected in a circuit.                                                  (1)

          4.8.3        State the condition of the comparator's output voltage when the
                       inverting terminal voltage is higher than the non-inverting terminal.              (1)
          4.8.4        State the function of the three 5 kΩ resistors.                                    (1)
          4.8.5        Briefly describe what happens when the voltage at Pin 2 falls below
                       ⅓ of the supply voltage.                                                           (2)
                                                                                                          [45]

Copyright reserved                                                                     Please turn over

### Page 14

Electrical Technology: Electronics             14                             DBE/November 2024
                                          NSC Confidential

QUESTION 5: SWITCHING CIRCUITS

5.1       Explain the concept negative feedback with reference to operational
          amplifiers.                                                                                  (2)

5.2       Name the switching circuit described by EACH of the following statements:

          5.2.1        In digital circuits and radio receivers it is used to recover signals
                       that have been polluted by noise.                                               (1)

          5.2.2        The output 'remembers' the last input and therefore this circuit is
                       often used as a memory element.                                                 (1)

          5.2.3        A circuit using a 741 IC receives an input pulse, the output swings
                       to -VCC momentarily and then swings back to its original
                       +VCC output state.                                                              (1)

5.3       FIGURE 5.3 below shows the circuit diagram of a 555 IC used as a bistable
          multivibrator. Answer the questions that follow.

                                                                      +9V

                                                                             R3
                   R2             R1                                        200 Ω
                  10 kΩ          10 kΩ
                                                                               LED1
                                                          8
                                                  4
                                                  7   555         3
                                                  6
                                                  2                            LED2
                                                      1       5
                      S2             S1
                                                                   C2        R4
                                                                  10 nF     200 Ω

                            FIGURE 5.3: 555 BISTABLE MULTIVIBRATOR

          5.3.1        State the purpose of resistor R2.                                               (1)

          5.3.2        Explain the operation of the circuit when S2 is pressed. Refer to the
                       inputs and the states of LED1 and LED2 in your response.                        (4)

          5.3.3        Explain how the circuit is reset.                                               (2)

Copyright reserved                                                                  Please turn over

### Page 15

Electrical Technology: Electronics                15                                          DBE/November 2024
                                             NSC Confidential

5.4       FIGURE 5.4 below shows a monostable multivibrator circuit using a
          741 op amp. Answer the questions that follow.

                                       C1
                                      1 µF                            +9 V
                                                        2             7
                              Input                                           6
                                                                                  Output

                                                      B 3
                                                                      4                 C2
                                                                      -9 V             1 µF
                                                R1

                                                                                       R2
                                               -VREF

                           FIGURE 5.4: MONOSTABLE MULTIVIBRATOR

          5.4.1        State the voltage at B during the circuit's resting condition.                                (1)
          5.4.2        Explain the purpose of having a negative reference voltage (-VREF)
                       in the circuit during its natural resting condition.                                          (2)

          5.4.3        Explain the operation of the circuit when a positive trigger input,
                       greater than VREF, is applied to the inverting input.                                         (3)

          5.4.4        Draw the output for the circuit on the ANSWER SHEET for
                       QUESTION 5.4.4 if R2 and C2 are chosen to create a changed
                       (unstable) state for 3 seconds.                                                               (4)

5.5       An astable multivibrator circuit can be constructed by using a 555 IC or a
          741 op amp. Answer the questions that follow.

          5.5.1        Complete the circuit diagram in FIGURE 5.5.1 on the ANSWER
                       SHEET for QUESTION 5.5.1 to make an astable multivibrator.

                                                            +supply
                                                  2               7
                                                                          6         Output
                                                            741
                                                  3
                                                                  4

                                                            - supply

                                                                                  R2

                               FIGURE 5.5.1: INCOMPLETE CIRCUIT DIAGRAM OF
                                      AN ASTABLE MULTIVIBRATOR                                                       (4)

          5.5.2        Differentiate between the output voltages of an astable multivibrator
                       circuit using a 741 op amp and an astable multivibrator circuit using
                       a 555 IC.                                                                                     (2)

Copyright reserved                                                                                Please turn over

### Page 16

Electrical Technology: Electronics                16                          DBE/November 2024
                                             NSC Confidential

5.6       FIGURE 5.6 below shows a 741 op amp comparator circuit. Answer the
          questions that follow.

                                                       9V

                       R1
                     100 k                                             R3
                                                                      10 k
                                                        741                          Q1
                                       R2
             Thermistor                                                                 R5
                                     100 k
               (PTC)                                                    R4             330
                                                                      4,7 k
                                                                                        LED

                     FIGURE 5.6: COMPARATOR AS A TEMPERATURE SENSOR

          5.6.1         Name the component that sets the reference voltage in the circuit.           (1)

          5.6.2         Name TWO components that make up the sensing unit.                           (2)

          5.6.3         Explain how the temperature setting can be changed in the
                        comparator.                                                                  (2)

5.7       State TWO applications of a Schmitt trigger.                                               (2)

5.8       FIGURE 5.8 below shows the circuit diagram of an inverting summing
          amplifier. Answer the questions that follow.

                                                                R4 = 100 kΩ
                                     R1 = 10 kΩ
            V1 = 500 mV
                                                                     +9 V
                                     R2 = 10 kΩ
            V2 = 450 mV
                                     R3 = 10 kΩ
            V3 = 300 mV                                                                VOUT
                                                                      -9 V

                                     FIGURE 5.8 SUMMING AMPLIFIER

Copyright reserved                                                                Please turn over

### Page 17

Electrical Technology: Electronics             17                             DBE/November 2024
                                          NSC Confidential

          Given:

          R1 = R2 = R3 = 10 kΩ
          R4        = 100 kΩ (variable)
          V1        = 500 mV
          V2        = 450 mV
          V3        = 300 mV

          5.8.1        Explain the purpose of variable resistor R4 in the circuit.                      (2)

          5.8.2        Calculate the output voltage if R4 is set to 72 kΩ                               (3)

          5.8.3        State why the output voltage can be calculated by the formula
                       𝑉𝑂𝑈𝑇 = −(𝑉1 + 𝑉2 + 𝑉3 ) when R4 is set to 10 kΩ.                                 (1)

          5.8.4        Explain the effect on the circuit and its output if the value of R 4 is
                       increased beyond 72 kΩ.                                                          (2)

5.9       FIGURE 5.9 below shows the input and output waveforms for a short time
          constant in a passive RC differentiator circuit. Answer the questions that
          follow.

                                            VIN

                                              0

                                          VOUT
                                              0

                     FIGURE 5.9: PASSIVE RC DIFFERENTIATOR WAVEFORMS

          5.9.1        Explain the primary function of a passive differentiator circuit.                (2)

          5.9.2        Draw, on the ANSWER SHEET for QUESTION 5.9.2, the output
                       waveform for a long time constant of the circuit for ONE full cycle.             (3)

5.10      Differentiate between an op amp differentiator and an op amp integrator with
          reference to circuit configuration.                                                           (2)
                                                                                                        [50]

Copyright reserved                                                                   Please turn over

### Page 18

Electrical Technology: Electronics                   18                        DBE/November 2024
                                                NSC Confidential

QUESTION 6: AMPLIFIERS

6.1        Describe the term attenuation with reference to amplifiers.                                 (2)

6.2        FIGURE 6.2 below shows a transistor amplifier biased with resistor
           RC = 800 Ω and a supply voltage VCC = 12 V. Answer the questions that
           follow.

      IC   (mA)
                                                                                            +Vcc
                                                                                            12 V
      15
                                                                             RC
                                                            RB              800 Ω

      10

                                                                     IB
                                                                                    Q
      5                                                                                      VCE
                                                                     VBE
                                                                    0,7 V

                                                             VCE                                   0V
              2      4      6     8   10   12     14   16
                                FIGURE A                                      FIGURE B

                         FIGURE 6.2: DC LOAD LINE AND TRANSISTOR BIASING

           6.2.1          Briefly explain the purpose of the DC load line, as drawn in
                          FIGURE A above.                                                              (1)

           6.2.2          Determine the value of VCE when the base current (IB) is equal to
                          zero.                                                                        (1)

           6.2.3          Determine the quiescent point voltage for a class A amplification.
                          Give a reason for your answer.                                               (2)

           6.2.4          Indicate the quiescent point of QUESTION 6.2.3 on the ANSWER
                          SHEET for QUESTION 6.2.4.                                                    (2)

Copyright reserved                                                                  Please turn over

### Page 19

Electrical Technology: Electronics               19                              DBE/November 2024
                                            NSC Confidential

6.3       Refer to FIGURE 6.3 below and answer the questions that follow.

                                  Low-                                    High-
                              frequency                                frequency
                                 range     Mid-frequency range            range
                     Vgain

                       AV

                     -3 dB

                                               Bandwidth

                                                                                    f (Hz)
                              f1 f2                                     f3 f 4
                           Low                                           High
                       frequencies                                   frequencies

                              FIGURE 6.3: FREQUENCY RESPONSE CURVE

          6.3.1         Identify the amplifier circuit from which the frequency response
                        curve in FIGURE 6.3 is derived.                                                 (1)

          6.3.2         Explain the term roll-off at the high-frequency range of an amplifier.          (1)

          6.3.3         With reference to the frequency response curve above, explain
                        why the gain falls at:

                        (a)     High frequencies                                                        (2)

                        (b)     Low frequencies                                                         (2)

Copyright reserved                                                                   Please turn over

### Page 20

Electrical Technology: Electronics               20                                DBE/November 2024
                                            NSC Confidential

6.4       FIGURE 6.4 below shows an amplifier circuit diagram. Answer the questions
          that follow.

                      R1      Transformer               R3                                   speaker
                                  T1
                                                                         Transformer
                                                                             T2
                                      Q1                            Q2

                                                               C2                      C3
                      R2             RE1    C1          R4                RE2

                                                                                                  0V

                           FIGURE 6.4: AMPLIFIER CIRCUIT DIAGRAM

          6.4.1        Identify the amplifier in FIGURE 6.4 above.                                             (1)

          6.4.2        Name TWO devices that might be connected to the secondary
                       terminals of transformer T2, apart from the loudspeaker.                                (2)

          6.4.3        State the function of transformer T 1 in the circuit.                                   (1)

          6.4.4        Describe what would happen if a 16 Ω, 10 W loudspeaker is
                       connected to the output of a 8 Ω, 10 W transformer (T2) in
                       FIGURE 6.4 above.                                                                       (3)

Copyright reserved                                                                          Please turn over

### Page 21

Electrical Technology: Electronics                   21                                DBE/November 2024
                                                NSC Confidential

6.5       FIGURE 6.5 below shows a push-pull amplifier connected to a speaker.
          Answer the questions that follow.

                                                                                                  +Vcc
                                         RB1
                                                                   NPN
                                                                transistor

                                                                     C

             Input signal                RB 2
                                                                  PNP
                                                               transistor    Speaker

                                                                                                  0V

                                     FIGURE 6.5: PUSH-PULL AMPLIFIER

          6.5.1        Identify the type of the push-pull amplifier circuit in FIGURE 6.5
                       above.                                                                                 (1)

          6.5.2        Explain the function of capacitor C in the circuit.                                    (2)

          6.5.3        Draw, on the ANSWER SHEET for QUESTION 6.5.3, the output
                       waveform that would appear across the PNP transistor.                                  (3)

6.6       Refer to FIGURE 6.6 below and answer the questions that follow.

                                                                                             +VCC
                                                                        T2

                                 R1      C1                                    C2           Output

                            T1
                                                          Q1

           Input

                                 R2     C3           R3            CE
                                                                                             0V

                             FIGURE 6.6: RADIO-FREQUENCY AMPLIFIER

Copyright reserved                                                                         Please turn over

### Page 22

Electrical Technology: Electronics             22                                  DBE/November 2024
                                          NSC Confidential

          6.6.1        State the purpose of transistor Q1 in FIGURE 6.6.                                     (1)

          6.6.2        Describe how the radio-frequency amplifier circuit can be tuned to
                       amplify different frequencies.                                                        (2)

          6.6.3        Draw a fully labelled frequency response curve of the radio-
                       frequency amplifier on the ANSWER SHEET for QUESTION 6.6.3.                           (4)

6.7       Refer to FIGURE 6.7 below and answer the questions that follow.

                                                                                  + VCC

                                                                                 RF choke

                                           C2                               C4
                                                       R1
                                                                                              output
                                                 C3
                                                                       Q1

                                     L1
                                                       R2
                                                                  R3
                                                                            C5
           C1

                                                                                             0V

                                     L2

                             FIGURE 6.7: HARTLEY OSCILLATOR

          6.7.1        Briefly discuss the freewheeling effect of the tank circuit.                          (3)

          6.7.2        State ONE function of the coupling capacitors C2 and C3 in
                       FIGURE 6.7 above.                                                                     (2)

Copyright reserved                                                                        Please turn over

### Page 23

Electrical Technology: Electronics                 23                           DBE/November 2024
                                              NSC Confidential

6.8       Refer to FIGURE 6.8 below and answer the questions that follow.

                                                                                    +VCC

                                           RB                         RC

                                                                           C5
                                                                                      V
                                                                                      VOUT
                                                                                        UIT

                     C1         C2       C3
                                                                      Q1

                      R1         R2        R3                    R4   C4

                                                                                      0V

                           FIGURE 6.8: RC PHASE-SHIFT OSCILLATOR

          6.8.1           Describe how the values of the capacitors (C1, C2, C3) and
                          resistors (R1, R2, R3) in the feedback network are selected for the
                          phase-shift oscillator.                                                   (2)

          6.8.2           State the similarity between an RC phase-shift oscillator and a
                          radio-frequency amplifier circuit with reference to their operating
                          frequencies.                                                              (2)

6.9       Differentiate between an RC phase-shift oscillator and an LC oscillator circuit
          with reference to their feedback circuits.                                                (2)
                                                                                                    [45]

                                                                                      TOTAL:        200

Copyright reserved

### Page 24

Electrical Technology: Electronics                                               DBE/November 2024
                                      NSC Confidential

                                     FORMULA SHEET

RLC CIRCUITS                             SEMICONDUCTOR DEVICES
XC 
       1                                                   VOUT      RF 
     2 π fC                              Gain A V                      
                                                            VIN       R IN 
                                                        R 
XL  2 fL                               VOUT  VIN    F 
                                                        RIN 
            1                                             R 
fr                                      VOUT  VIN  1  F 
       2 LC                                              R IN 

SERIES                                   SWITCHING CIRCUITS
    V                                                 RF     RF    RF
IT  T                                   VOUT = - (V1    +V1    +V1 )
     Z                                                R1     R2    R3
VL  I XL                                VOUT   (V1  V2  V3  ....VN )
VC  I X C                                                   R2
VT  I Z                                 VFB = VSAT ×
                                                            R1 +R2
       XL X C VL VC 1 L
Q                                   T=1,1×R1 C1
       Z   Z VT VT R C
Z  R2  XL  XC 
                             2                1
                                         𝑓=
                                              T
VT         VR
                 2
                      VL  VC 
                                 2                           R2
                                         VTRIG =VOUT ×
                                                            R1 +R2
       R
Cos θ                                   AMPLIFIERS
       Z
       V                                     V
Cos θ  R                                Ic  C             AND      VCC  VCE  ICR C
        VT                                   R     C
                                                    I
PARALLEL                                 A  20log o
                                           i         I
                                                      i
       I                                              Vo
Cos θ  R                                A V  20log
       IT                                              V
                                                        i
IT  IR 2  IL  IC 2                  PO  I2  Z o
       VR                                           P
IR                                      A P  10log o
       R                                            P
                                                      i
     VC                                  A v dB   20logA
IC                                                             V
     XC
    V                                                      VOUT      RF 
IL  L                                   Gain A V                     
    XL                                                      VIN       RIN 
       R   R                                           1                                   1
Q=       =                               𝑓𝑂 =                                    𝑓𝑂 =
       XL XC                                      2𝜋√𝐿𝐶𝑇                                2𝜋√𝐿 𝑇 𝐶
     f                                              1
BW  r                                   𝑓𝑂 =
     Q                                            2𝜋√6𝑅𝐶

Copyright reserved

### Page 25

Electrical Technology: Electronics                                                      DBE/November 2024
                                               NSC Confidential

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET

QUESTION 5: SWITCHING CIRCUITS

5.4.4
                            Trigger pulse

               0            1        2    3         4      5           6   t (s)

            +9 V

            VOUT                                                                   Transfer mark to
                                                                           t (s)   answer book

            -9V

                                                                                                      MOD

                                                   FIGURE 5.4.4                                             (4)

5.5.1

                                         +supply
                                     2         7
                                                    6              Output
                                         741
                                     3
                                               4

                                         - supply
                                                                                   Transfer mark to
                                                                                   answer book

                                                                  R2

                                                                                                      MOD

                                                   FIGURE 5.5.1                                             (4)

Copyright reserved

### Page 26

Electrical Technology: Electronics                             DBE/November 2024
                                     NSC Confidential

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET

5.9.2

             VIN

                0

            VOUT

                0

                                                        Transfer mark to
                                                        answer book

                                                                           MOD

                                       FIGURE 5.9.2                                (3)

Copyright reserved

### Page 27

Electrical Technology: Electronics                                               DBE/November 2024
                                               NSC Confidential

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET

QUESTION 6: AMPLIFIERS

6.2.4
              IC     (mA)

            15

            10

             5

                                                                             Transfer mark to
                                                                       VCE   answer book
                       2     4       6     8     10    12    14   16
                                         FIGURE A

                                                                                                MOD

                                                  FIGURE 6.2.4                                        (2)

Copyright reserved

### Page 28

Electrical Technology: Electronics                              DBE/November 2024
                                     NSC Confidential

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET

6.5.3
             +V

              0
                                                   t

             -V

             +V

              0
                                                   t
                                                        Transfer mark to
                                                        answer book

             -V
                                                                           MOD

                                        FIGURE 6.5.3                                (3)

Copyright reserved

### Page 29

Electrical Technology: Electronics                                  DBE/November 2024
                                     NSC Confidential

CENTRE NUMBER:

EXAMINATION NUMBER:

ANSWER SHEET

6.6.3

             Gain

                                                        Frequency

                                                               Transfer mark to
                                                               answer book

                                                                                  MOD

                                        FIGURE 6.6.3                                    (4)

Copyright reserved

## Related documents

- [Electrical Technology May-June 2024 (Power Systems) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/0d8d71f4-5725-40ea-9e29-a19e1c8a7867) — Electrical Technology · QP · 2024 · Eng
- [Electrical Technology May-June 2024 (Digital) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/2b227e9b-0513-468e-8b1a-d4df808071cd) — Electrical Technology · QP · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Power Systems Afrikaans](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-afrikaans/1a395c97-b838-42e6-9bd6-30a85a714b11) — Electrical Technology · Memo · 2024 · Afr
- [ELEC TECH GR12 MEMO SEPT2024 Power Systems English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-english/bea78337-b137-406a-9b4a-c6e631a84c9d) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Electronics English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-electronics-english/c80784c8-a9c8-49f8-b740-a29558fe2de9) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-digital-english/cb603860-b00d-40c2-a36b-aa5e97b7d1e5) — Electrical Technology · Memo · 2024 · Eng

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [ELECTRIC TECH (Digital) MEMO GR12 SEPT 2025 ENG watermark](https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d) — Memo · 2025 · Eng
- [Electrical Technology P1 (Electronics) (English) June 2025 Possible Answers](https://www.hlayiso.com/library/electrical-technology-p1-electronics-english-june-2025-possible-answers/4302563e-89b7-4f54-8a21-63b2020e985f) — Memo · 2025 · Eng
- [Electrical Technology Nov 2025 (Digital) MG Afr](https://www.hlayiso.com/library/grade-12-electrical-technology-2025-nsc-november-exam-memorandum/3b862a0c-6a87-4296-b5b6-09b072c7d1e9) — Memo · 2025 · Afr
- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Memo · 2023 · Eng
- [ELEC TECH MEMO SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-electronics-english/5630ca3e-e352-4f96-81d0-64ec0103c0e9) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
