# Electrical Technology Grade 12 November 2024 NSC Memo (Eng)

> Grade 12 Electrical Technology memorandum from the November 2024 NSC (English), 16 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-mg-eng/fdcfaa8e-04be-4c18-beb4-dc6382c98f52
- Updated: 2026-10-29
- Subject: Electrical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 16

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 November 2024 NSC Memo (Eng)](https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-mg-eng/fdcfaa8e-04be-4c18-beb4-dc6382c98f52)

## About this document

Electrical Technology · Grade 12 · November 2024 NSC · 2024. Memorandum. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

NATIONAL
                              SENIOR CERTIFICATE

                                      GRADE 12

                     ELECTRICAL TECHNOLOGY: ELECTRONICS

                                   NOVEMBER 2024

                               MARKING GUIDELINES

MARKS: 200

                      These marking guidelines consist of 16 pages.

Copyright reserved                                                    Please turn over

### Page 2

Electrical Technology: Electronics              2                           DBE/November 2024
                                     NSC – Marking Guidelines

INSTRUCTIONS TO THE MARKERS

1.        All questions with multiple answers imply that any relevant, acceptable
          answer should be considered.

2.        Calculations:

          2.1          All calculations must show the formulae.

          2.2          Substitution of values must be done correctly.

          2.3          All answers MUST contain the correct unit to be considered.

          2.4          Alternative methods must be considered, provided that the correct
                       answer is obtained.

          2.5          Where an incorrect answer could be carried over to the next step,
                       the first answer will be deemed incorrect. However, should the
                       incorrect answer be carried over correctly, the marker has to re-
                       calculate the values, using the incorrect answer from the first
                       calculation. If correctly used, the candidate should receive the full
                       marks for subsequent calculations.

3.        These marking guidelines is only a guide with model answers. Alternative
          interpretations must be considered and marked on merit. However, this
          principle should be applied consistently throughout the marking session at
          ALL marking centres.

Copyright reserved

### Page 3

Electrical Technology: Electronics              3               DBE/November 2024
                                     NSC – Marking Guidelines

QUESTION 1: MULTIPLE CHOICE

1.1       B✓                                                                          (1)

1.2       A✓                                                                          (1)

1.3       B✓                                                                          (1)

1.4       A✓                                                                          (1)

1.5       C✓                                                                          (1)

1.6       B ✓                                                                         (1)

1.7       D✓                                                                          (1)

1.8       B✓                                                                          (1)

1.9       B✓                                                                          (1)

1.10      C✓                                                                          (1)

1.11      C✓                                                                          (1)

1.12      B/C ✓                                                                       (1)

1.13      B✓                                                                          (1)

1.14      D✓                                                                          (1)

1.15      C✓                                                                          (1)
                                                                                      [15]

Copyright reserved                                                 Please turn over

### Page 4

Electrical Technology: Electronics              4                         DBE/November 2024
                                     NSC – Marking Guidelines

QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

2.1       Workplace means any premises or place where a person performs work ✓ in
          the course of employment. ✓                                                             (2)

2.2       Your right to fair labour practices. ✓
          Your right to work reasonable hours. ✓
          Your right to belong to a trade union.
          Your right to earn a living wage.
          Your right not to be discriminated against.
          Your right to work in a safe environment.                                               (2)

2.3       Poor ventilation reduces the correct amount of oxygen ✓ which might lead
          to drowsiness. ✓
          NOTE: If reference is made to other effects that relates to poor ventilation like
          drowsiness, accidents etc. the answer will be accepted on merit.                        (2)

2.4       •     To dismiss an employee without due process. 
          •     To reduce the rate of remuneration without due process. 
          •     Alter the terms of conditions of his/her employment to terms of conditions
                that is less favourable to him/herself.
          •     Harassment and verbal abuse.
          •     Alter position relative to other people.
          •     Treat employees unfair because of race.

          NOTE: If a learner only mentions an infringement of rights only 1 mark will be
          awarded. Duplicate mentioning of rights will not be awarded.                            (2)

2.5       Equipment may be damaged making it unsafe  endangering the life of other
          users  which might lead to an accident/injury.                                         (2)
                                                                                                  [10]

Copyright reserved                                                             Please turn over

### Page 5

Electrical Technology: Electronics                 5                         DBE/November 2024
                                        NSC – Marking Guidelines

QUESTION 3: RLC CIRCUITS
3.1       3.1.1        Inductive reactance is the opposition to the flow of current ✓ when
                       an inductor is connected to an ac supply. ✓
                       Inductive reactance is the opposition offered to the flow of
                       alternating current by an inductor.                                         (2)
          3.1.2        Bandwidth is the range of frequencies ✓ for which the circuit output
                       voltage (or) current value equals 70,7 % or more of its maximum
                       amplitude. ✓
                       NOTE: A band of frequencies centred around the resonant
                       frequency without mentioning 70,7% of the amplitude will be
                       awarded 1 mark.
                       The bandwidth of an RLC circuit refers to the range of frequencies
                       over which an RLC circuit effectively responds to an input signal
                       and transmits more than 50% of the power to a load.                         (2)
3.2       3.2.1        Lagging ✓                                                                   (1)
          3.2.2        𝑉𝐿 = 𝐼𝑋𝐿                               ✓
                           𝑉𝐿
                       𝐼=
                           𝑋𝐿
                           3,45                               ✓
                        =
                           150
                        = 23 𝑚𝐴                               ✓
                        = 0,023 𝐴                                                                  (3)
          3.2.3        𝑋𝐿 = 2𝜋𝑓𝐿                              ✓
                            𝑋𝐿
                       𝐿=
                           2𝜋𝑓
                               150                            ✓
                          =
                              2𝜋(50)
                          = 477,46 𝑚𝐻
                                                              ✓
                          = 0,48 𝐻
                                                                                                   (3)
          3.2.4        𝑍 = √𝑅 2 + (𝑋𝐿 − 𝑋𝐶 )2                 ✓
                       𝑅 = √𝑍 2 − (𝑋𝐿 − 𝑋𝐶 )2
                                                              ✓
                         = √106,422 − (150 − 113,6)2
                         = 100 Ω                              ✓                                    (3)
          3.2.5                  VL ✓
                                                          ✓
                                                         VT
                         (VL – VC)
                                                θ                       ✓
                                                    IT   VR
                                                                  Rotation
                                  ✓
                                 VC
                       NOTE: Rotation and VT are compulsory marks, thereafter any two
                            correctly placed labels.
                            XL and XC will not be accepted as the given diagram to
                            complete from the question paper indicated voltage values.             (4)
Copyright reserved                                                              Please turn over

### Page 6

Electrical Technology: Electronics                6                     DBE/November 2024
                                       NSC – Marking Guidelines

          3.2.6        A decrease in frequency caused the inductive reactance to
                       decrease ✓ and the capacitive reactance to increase. ✓ When
                       these two values move closer to one another their effects cancel
                       each other out decreasing the impedance ✓ causing the current to
                       increase and the phase angle to decrease.                               (3)

3.3       3.3.1             𝑉𝑇                              ✓
                       𝐼𝑅 =
                            𝑅
                            230                             ✓
                          =
                            60
                          = 3,83 𝐴                          ✓                                  (3)

          3.3.2               𝑉𝑇                            ✓
                       𝑋𝐶 =
                              𝐼𝐶
                                                            ✓
                            230
                          =
                            9,2
                          = 25 Ω                            ✓                                  (3)

          3.3.3        IT = IR = 3,83 A                     ✓
                       XC = XL which indicates that the     ✓
                       circuit is at resonance                                                 (2)

          3.3.4        XC = XL
                            𝑅                               ✓
                       𝑄=
                           𝑋𝐿
                                                            ✓
                            60
                          =
                            25
                          = 2,4                             ✓                                  (3)

          3.3.5                 𝑓𝑟                          ✓
                       𝐵𝑊 =
                                𝑄
                                                            ✓
                                50
                              =
                                2,4
                              = 20,83 𝐻𝑧                    ✓                                  (3)
                                                                                               [35]

Copyright reserved                                                          Please turn over

### Page 7

Electrical Technology: Electronics                7                          DBE/November 2024
                                       NSC – Marking Guidelines

QUESTION 4: SEMICONDUCTOR DEVICES

4.1       P-channel ✓ enhancement ✓ MOSFET                                                           (2)

4.2       4.2.1        The pinching state is reached by increasing the gate to source
                       voltage, ✓ which widens the depletion regions on both sides of the
                       channel, ✓ resulting in the drain current (ID) being reduced. ✓               (3)

          4.2.2        The Junction field effect transistor (JFET) operates with its gate-
                       source junction ✓ reverse–biased ✓ which makes the input
                       resistance at the gate very high whilst the bipolar junction transistor
                       operates with the forward biased base-emitter junction ✓ which
                       result in a lower resistance.                                                 (3)

4.3       4.3.1        MOSFET transfer ✓ characteristic curve
                       MOSFET transconductance characteristic curve                                  (1)

          4.3.2        A – Cut-off region ✓
                       B – Enhancement region ✓                                                      (2)

          4.3.3        •  When the input gate-source voltage (VGS) is low✓, the channel
                          drain current (ID) is low. ✓
                       • When the gate-source voltage rises, ✓ the channel widens and
                          the drain current increases. ✓
                       NOTE: If a candidate mentions that VGS and ID are directly
                       proportional 2 marks will be awarded and any of the two bullets
                       above can be mentioned for the other 2 marks.                                 (4)

          4.3.4        Amplifier ✓
                       Switch ✓                                                                      (2)

4.4       The JFET only operates in the depletion mode. ✓
          The MOSFET operates in both depletion and enhancement modes.                               (1)

4.5       4.5.1        Positive pulse. ✓                                                             (1)

          4.5.2        When the emitter is supplied with sufficient current, ✓ the operating
                       point will continue falling ✓ from the peak point until it reaches the
                       valley point.
                       When VE  VX , the operating point will fall from the peak point until
                       it reaches the valley point.                                                  (2)

          4.5.3        (a)    Unijunction transistor (UJT) consists of a single PN -junction✓
                              whilst a bipolar junction transistor (BJT) consists of two
                              PN-junctions ✓ called Emitter Base Junction and Collector-
                              Base junction.                                                         (2)

                       (b)    The unijunction transistor is essentially a voltage controlled
                              switch and does not have amplifying properties. ✓ The
                              Bipolar Junction transistor (BJT) is current operating device
                              and has amplifying properties. ✓                                       (2)

Copyright reserved                                                                Please turn over

### Page 8

Electrical Technology: Electronics                    8                           DBE/November 2024
                                           NSC – Marking Guidelines

4.6       4.6.1        FIGURE A - output voltage will be positive/high. ✓
                       FIGURE B - output voltage will be negative/low. ✓                                    (2)
          4.6.2        Small size ✓
                       Cheap ✓
                       Low power consumption
                       Highly stable
                       Highly reliable                                                                      (2)
          4.6.3        Common mode rejection ratio is the ability of an op-amp to
                       suppress common mode signals. ✓
                       The common mode rejection ratio is the ratio between the output
                       voltage to the common input voltage when the same signal is
                       applied simultaneously to both inputs.                                               (1)
4.7       4.7.1        Negative feedback. ✓                                                                 (1)
          4.7.2                      𝑅𝐹                 ✓
                       𝐴𝑉 = −
                                     𝑅𝐼𝑁
                                 4 700                  ✓
                            =−
                                  470
                            = −10                       ✓
                                                                                                            (3)
          4.7.3        𝑉𝑂𝑈𝑇 = 𝐴𝑉 × 𝑉𝐼𝑁                  ✓                               𝑅𝑓
                                                                      𝑉𝑂𝑈𝑇 = 𝑉𝐼𝑁 × (−       )
                             = −10 × 2 × 10−3                                           𝑅𝐼𝑁
                                                        ✓    OR
                             = −0,02𝑉                                                     4700
                                                                      𝑉𝑂𝑈𝑇 = 0,002 × (−        )
                                                        ✓                                 470
                             = −20 𝑚𝑉
                                                                      𝑉𝑂𝑈𝑇 = −0,02 𝑉
                                                                                                            (3)
          4.7.4        The output voltage will be able to swing above ✓ and below ✓ the
                       zero levels.                                                                         (2)

          4.8.1        Controlling the positioning of a servo device. ✓
                       Temperature measurement.
                       Timers in oven temperature control.
                       Oscillator as motor speed control.                                                   (1)
          4.8.2                                                              ̅ from the
                       The NPN transistor (T1) will only turn on when output Q
                       flip-flop goes high. ✓                                                               (1)
          4.8.3        When the inverting terminal voltage is higher - the comparator's
                       output will be low. ✓                                                                (1)
          4.8.4        It divides the supply voltage into three equal values. ✓
                       The resistors act as voltage dividers.                                               (1)

Copyright reserved                                                                       Please turn over

### Page 9

Electrical Technology: Electronics                9                             DBE/November 2024
                                       NSC – Marking Guidelines

          4.8.5        The 555 IC will be triggered ✓ and the output voltage at Pin 3 rises
                       near to the supply voltage ✓
                       NOTE: Due to the error in the schematic diagram of the 555 IC, the
                       following response will be accepted:
                       When pin 2 falls below ⅓VCC, the output of comparator C2 will be
                       low, if R of the flip-flop is high, the circuit will be reset, if R is low,
                       the circuit will stay in its previous state.                                     (2)
                                                                                                        [45]

QUESTION 5: SWITCHING CIRCUITS
5.1       Negative feedback is when a portion of the output signal ✓ is fed back to the
          input, out of phase ✓ or subtracted from the input.                                           (2)

5.2       5.2.1        Schmitt trigger ✓                                                                (1)

          5.2.2        Bistable multivibrator ✓                                                         (1)

          5.2.3        Monostable multivibrator ✓                                                       (1)

5.3       5.3.1        R2 is a pull-up resistor ✓
                       R2 keeps the voltage on pin 2 high.                                              (1)
          5.3.2        •   When S2 is pressed it connects pin 2 to 0 V. ✓
                       •   This low input triggers the circuit and the output goes high. ✓
                       •   When output goes high LED2 is forward biased and switched
                           ON. ✓
                       •   while LED1 is reversed biased and switched OFF. ✓                            (4)

          5.3.3        The circuit is reset by pressing S1. ✓ This connects reset pin 4
                       to 0 V. ✓                                                                        (2)

5.4       5.4.1        0V✓                                                                              (1)
          5.4.2        During its natural resting condition, the negative reference voltage
                       keeps the potential on the inverting input negative ✓ ensuring that
                       the output remains stable at +VCC. ✓                                             (2)
          5.4.3        When a positive trigger voltage greater than VREF is applied to the
                       inverting input its potential will be greater than the 0 V on the non-
                       inverting input ✓ causing the output to saturate to – VCC ✓ where it
                       will remain for the duration of the time constant determined by
                       C2 and R2. ✓                                                                     (3)

Copyright reserved                                                                   Please turn over

### Page 10

Electrical Technology: Electronics                   10                                        DBE/November 2024
                                           NSC – Marking Guidelines

          5.4.4          Trigger pulse

                                      0             1        2       3   4        5    6   t (s)

                                               ✓                                  ✓
                                 +9V

                                 VOUT
                                                                                           t (s)

                                                             ✓               ✓
                                     -9V

                       NOTE:         1 mark for starting the output at +9 V
                                     1 mark for the output changing from +9 V to -9 V at trigger
                                     input
                                     1 mark for the correct duration of the output state
                                     1 mark for the return to +9 V                                                    (4)
                                     An inverted waveform will loose 1 mark for orientation.

5.5       5.5.1                                RF       ✓

                                                    +supply
                                           2             7

                                                   741
                                                                 6            Output
                                           3
                                                         4
                                                                             R1 ✓
                                                    - supply

                          ✓                        ✓
                                      C1                                     R2

                                                                                                                      (4)
          5.5.2        The output voltage of a 741 op-amp astable multivibrator circuit
                       constantly changes between + VCC and -VCC ✓ where the output of
                       a 555 IC astable multivibrator circuit changes between +VCC
                       and 0 V. ✓                                                                                     (2)
5.6       5.6.1        Variable resistor/Potentiometer R2 ✓                                                           (1)

          5.6.2        Resistor R1 ✓
                       Thermistor ✓                                                                                   (2)

          5.6.3        By adjusting variable resistor R2 ✓ the new reference voltage at
                       the inverting input will change. ✓                                                             (2)

5.7       Clean up signals in radio receivers. ✓
          Eliminate noise caused by switch bounce in digital circuits. ✓
          Changing of sine waves into square or rectangular waves
          Signal recovery after severe distortion.                                                                    (2)

Copyright reserved                                                                                 Please turn over

### Page 11

Electrical Technology: Electronics               11                         DBE/November 2024
                                       NSC – Marking Guidelines

5.8       5.8.1        Variable resistor R4 provides negative feedback ✓ that controls the
                       gain of the circuit. ✓                                                       (2)
          5.8.2                       𝑅𝐹      𝑅𝐹     𝑅𝐹                              ✓
                       𝑉𝑂𝑈𝑇 = − (𝑉1      + 𝑉2    + 𝑉3 )
                                      𝑅1      𝑅2     𝑅3
                                          72000          72000         72000         ✓
                             = − (0,5 ×         + 0,45 ×       + 0,3 ×       )
                                          10000          10000         10000
                             = −9 𝑉                                                  ✓
                                                                                                    (3)
                       NOTE: Due to the error on the formula sheet provided, the
                       following calculation will be accepted.

                                      𝑅𝐹      𝑅𝐹     𝑅𝐹
                       𝑉𝑂𝑈𝑇 = − (𝑉1      + 𝑉1    + 𝑉1 )
                                      𝑅1      𝑅2     𝑅3
                                          72000         72000         72000
                             = − (0,5 ×         + 0,5 ×       + 0,5 ×       )
                                          10000         10000         10000
                             = −10,8 𝑉

          5.8.3        When RF = R1 = R2 = R3. ✓ They cancel each other out in the
                       formula giving VOUT = -(V1+V2+V3).
                       When R4 is set to 10 kΩ the overall circuit gain is 1.                       (1)

          5.8.4        When R4 is increased beyond 72 kΩ the gain of the amplifier
                       increases ✓ driving it into saturation and causing distortion on the
                       output. ✓
                       NOTE: Because of the formula provided on the formula sheet a
                       reason in-line with the calculated answer in 5.8.2 will be accepted.
                       e.g. The circuit is already in saturation, when R4 is increased the
                       output voltage will remain at a maximum of 9 V.                              (2)

5.9       5.9.1        A passive differentiator primarily performs mathematical
                       differentiation on an input signal, ✓ producing an output voltage
                       proportional to the rate of change of the input voltage. ✓                   (2)

Copyright reserved                                                               Please turn over

### Page 12

Electrical Technology: Electronics                 12                       DBE/November 2024
                                         NSC – Marking Guidelines

          5.9.2

                                            VIN

                                              0

                                                      ✓

                                           VOUT
                                                             ✓
                                              0
                                                                     ✓

                       NOTE:         The wave shape must be correct before any marks are
                                     allocated
                                     1 mark for orientation
                                     1 mark for each ½ cycle                                       (3)

5.10      In an op-amp differentiator a capacitor is connected to the inverting input and
          resistor used in the feedback loop. ✓
          In an op-amp integrator a resistor is connected to the inverting input with a
          capacitor in the feedback loop. ✓                                                        (2)
                                                                                                   [50]

Copyright reserved                                                              Please turn over

### Page 13

Electrical Technology: Electronics               13                           DBE/November 2024
                                       NSC – Marking Guidelines

QUESTION 6: AMPLIFIERS

6.1        Attenuation refers to a circuit with a output voltage smaller ✓ than the input
           voltage. ✓
           Attenuation is the reduction in signal voltage as it passes through a circuit
           and corresponds to a gain of less than 1.                                                  (2)

6.2        6.2.1       DC load line is the line on the output characteristic of a transistor
                       circuit showing the operating points of the amplifier. ✓                       (1)

           6.2.2       VCE will be equals to VCC = 12 V.✓                                             (1)

           6.2.3       For class A amplification, the quiescent voltage is 6 V.✓
                       The value of the quiescent voltage is half ✓ the value of the supply
                       voltage i.e ½ VCC.                                                             (2)

           6.2.4
                                IC   (mA)

                               15

                               10
                                                     Q-Point ✓

                                5

                                                       ✓
                                                                                     VCE
                                       2     4     6       8   10   12   14   16
                                                       FIGURE A                                       (2)

6.3        6.3.1       RC coupled amplifier. ✓                                                        (1)

           6.3.2       Roll-off is the rate at which the gain decreases at high
                       frequencies.✓                                                                  (1)

           6.3.3       (a)    At high frequencies, the reactance of the small parasitic
                              capacitances of the transistors ✓ becomes lower ✓ and
                              lower, reducing the gain.                                               (2)

                       (b)    At low frequencies the coupling capacitor's reactance
                              rises, ✓ blocking more of the signal ✓ and also the
                              reactance of the decoupling capacitors with the emitter
                              resistance limit the gain.                                              (2)

Copyright reserved                                                                 Please turn over

### Page 14

Electrical Technology: Electronics              14                         DBE/November 2024
                                      NSC – Marking Guidelines

6.4        6.4.1       Transformer coupled ✓ amplifier.                                          (1)

           6.4.2       AC relay ✓
                       AC motor ✓
                       Piezo Buzzer                                                              (2)

           6.4.3       •   To match the two impedances and separate the dc circuits.✓
                       •   To couple the output of Q1 to the input of Q2.                        (1)

           6.4.4       There would be no maximum power transfer to the loudspeaker ✓
                       because the output impedance of the amplifier ✓ does not match
                       with the input impedance of the speaker ✓ thus meaning the
                       output sound will be softer.                                              (3)

6.5       6.5.1        Complementary ✓        Push pull amplifier.                               (1)

          6.5.2        Block DC signals ✓ and allows the AC signals to pass
                       through. ✓
                       The capacitor couples the circuit with the speaker and acts as a
                       short term power source for the PNP transistor during each
                       negative half cycle.                                                      (2)

          6.5.3
                                         +V

                                         0
                                                                       t

                                         -V

                                         +V

                                                     ✓
                                         0
                                                                       t

                                                                 ✓

                                         -V                  ✓
                                                                                                 (3)

                       NOTE: 1 mark for each half cycle = 2
                             1 mark for amplification

Copyright reserved                                                            Please turn over

### Page 15

Electrical Technology: Electronics               15                          DBE/November 2024
                                       NSC – Marking Guidelines

                       NOTE: 1 mark for same phase on negative half-cycle
                             1 mark for NO amplification shown.
6.6        6.6.1       The purpose of transistor Q1 is to amplify the input signal to a value
                       that drives the tank circuit to oscillation. ✓                               (1)

           6.6.2       By varying capacitors C1 and C2, the tuned circuit will resonate at
                       different frequencies, ✓ therefore changing range of frequencies.✓           (2)
           6.6.3                                                                    ✓
                                                                          Maximum gain at
                                                                         resonant frequency
                           Gain

                                                                                  ✓
                                                                         0,707 X Max Gain

                                                       Band pass ✓

                                                           fr     ✓        Frequency
                                                                                                    (4)
6.7        6.7.1       The transistor will be driven alternately on and off,✓ which in turn
                       continually charges the tank circuit ✓ keeping it oscillating at a
                       constant ✓ amplitude.                                                        (3)

           6.7.2       •    Block dc current from passing ✓ and allow the AC signal to
                            pass. ✓
                       •    The coupling capacitors C2 and C3 only allows a Radio
                            frequency signal from the amplifier to the tank circuit and back.       (2)

Copyright reserved                                                               Please turn over

### Page 16

Electrical Technology: Electronics             16                          DBE/November 2024
                                     NSC – Marking Guidelines

6.8        6.8.1       The values of the capacitors (C1,C2,C3) and resistors (R1,R2,R3) are
                       selected in such a way that each RC combination ✓ produces a
                       phase shift of 60o.✓                                                    (2)

           6.8.2       RC phase-shift oscillator and Radio-frequency amplifier operates at
                       a desired frequency ✓ and blocks/suppresses all other
                       frequencies. ✓
                       The RC phase-shift oscillator and Radio-frequency amplifier both
                       rely on resonant/phase shift networks to control their operating
                       frequencies.                                                            (2)

6.9        RC-phase shift oscillators use resistors and capacitors (RC timing circuit) in
           the feedback network. ✓
           LC oscillator uses capacitors and inductors in their feedback network. ✓            (2)
                                                                                               [45]

                                                                                  TOTAL:       200

Copyright reserved

## Related documents

- [Electrical Technology Nov 2024 (Electronics) Eng](https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-eng/870e3d22-85e9-42bd-890f-3ef1fd3333cf) — Electrical Technology · QP · 2024 · Eng
- [Electrical Technology Nov 2024 (Electronics) Afr](https://www.hlayiso.com/library/electrical-technology-nov-2024-electronics-afr/98972424-ba56-4bbc-a319-fdfc1fec40f8) — Electrical Technology · QP · 2024 · Afr
- [Electrical Technology Nov 2024 (Power Systems) Afr](https://www.hlayiso.com/library/electrical-technology-nov-2024-power-systems-afr/5f2b4850-fffb-4024-8f24-d74bd8677a25) — Electrical Technology · QP · 2024 · Afr
- [ELEC TECH GR12 MEMO SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-digital-english/cb603860-b00d-40c2-a36b-aa5e97b7d1e5) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 QP SEPT2024 Electronics Afrikaans](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-electronics-afrikaans/6fc3719e-6eab-469e-baf1-ca1645c8ebad) — Electrical Technology · QP · 2024 · Afr
- [ELEC TECH GR12 QP SEPT2024 Power Systems Afrikaans](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-power-systems-afrikaans/928e510b-68c2-4670-a7c7-fe20b388befb) — Electrical Technology · QP · 2024 · Afr

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [Electrical Technology (Power Systems) (English) June 2025 Question Paper](https://www.hlayiso.com/library/electrical-technology-power-systems-english-june-2025-question-paper/5422e67a-03a4-4202-ba9b-1b9ec9872537) — QP · 2025 · Eng
- [ELEC TECH GR12 QP SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2024-digital-english/9fcfef2b-6d5e-4601-853a-24a2a3993617) — QP · 2024 · Eng
- [Electrical Technology May-June 2024 (Power Systems) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/0d8d71f4-5725-40ea-9e29-a19e1c8a7867) — QP · 2024 · Eng
- [Electrical Technology May-June 2024 (Digital) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/2b227e9b-0513-468e-8b1a-d4df808071cd) — QP · 2024 · Eng
- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
