# Electrical Technology Grade 12 November 2024 NSC QP (Eng)

> Grade 12 Electrical Technology question paper from the November 2024 NSC (English), 22 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/electrical-technology-nov-2024-power-systems-eng/db208725-5713-4db9-a359-56459a2d0117
- Updated: 2026-09-27
- Subject: Electrical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 22

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 November 2024 NSC QP (Eng)](https://www.hlayiso.com/library/electrical-technology-nov-2024-power-systems-eng/db208725-5713-4db9-a359-56459a2d0117)

## About this document

Electrical Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 22 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Confidential

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

                ELECTRICAL TECHNOLOGY: POWER SYSTEMS

                                NOVEMBER 2024

MARKS: 200

TIME: 3 hours

        This question paper consists of 20 pages and a 2-page formula sheet.

Copyright reserved                                                   Please turn over

### Page 2

Electrical Technology: Power Systems         2                             DBE/November 2024
                                       NSC Confidential

INSTRUCTIONS AND INFORMATION

1.        This question paper consists of SEVEN questions.

2.        Answer ALL the questions.

3.        Sketches and diagrams must be large, neat and FULLY LABELLED.

4.        Show ALL calculations and round off answers correctly to TWO decimal
          places.

5.        Number the answers correctly according to the numbering system used in this
          question paper.

6.        You may use a non-programmable calculator.

7.        Calculations must include:

          7.1         Formulae and manipulations where needed

          7.2         Correct replacement of values

          7.3         Correct answer and relevant units where applicable

8.        A formula sheet is attached at the end of this question paper.

9.        Write neatly and legibly.

Copyright reserved                                                             Please turn over

### Page 3

Electrical Technology: Power Systems               3                      DBE/November 2024
                                             NSC Confidential

QUESTION 1: MULTIPLE-CHOICE QUESTIONS

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers (1.1 to 1.15) in
the ANSWER BOOK, e.g. 1.16 D.          Nov

1.1       A disastrous event, resulting from the use of plant and machinery, or from
          activities at a workplace, is known as a/an …

          A     minor incident.
          B     major incident.
          C     accident.
          D     risk.                                                                               (1)

1.2       The impedance in a RLC series circuit, is minimum when the …

          A     inductive reactance equals the capacitive reactance.
          B     inductive reactance is greater than the capacitive reactance.
          C     capacitive reactance is greater than the inductive reactance.                       (1)
          D     resistance is maximum.

1.3       In a pure capacitive circuit that is connected to an AC supply, the …

          A     voltage leads the current by 90°.
          B     current leads the voltage by 90°.
          C     voltage and current are in phase.
          D     current leads the voltage by 180°.                                                  (1)

1.4       The quality factor of an RLC parallel circuit is … to the bandwidth.

          A     inversely proportional
          B     directly proportional
          C     equal
          D     not related                                                                         (1)

1.5       … is transferred backwards and forwards between the supply, inductor or
          capacitor and performs no real work.

          A      Apparent power
          B      Real power
          C      Reactive power
          D      True power                                                                         (1)

1.6       The purpose of the neutral conductor in a three-phase AC system is to …

          A      carry the highest voltage.
          B      provide a return path for unbalanced currents.
          C      be used for phase shifting.
          D      carry current in a balanced system.                                                (1)

Copyright reserved                                                               Please turn over

### Page 4

Electrical Technology: Power Systems           4                          DBE/November 2024
                                         NSC Confidential

1.7       The purpose of a power factor meter in an electrical system is to …

          A      measure the energy.
          B      measure the voltage difference between phases.
          C      monitor harmonics in the current.
          D      indicate the phase relationship between voltage and current.                     (1)

1.8       A … configuration is used extensively as step-down transformers in
          distribution systems where a four-wire system is required.

          A      star-star
          B      star-delta
          C      delta-delta
          D      delta-star                                                                       (1)

1.9       If there is an earth fault in one of the phases of a three-phase transformer, the
          difference in voltage between phases will activate the …

          A      Buchholtz relay.
          B      restricted earth-fault relay.
          C      balanced earth-fault relay.
          D      standby earth-fault relay.                                                       (1)

1.10      When a three-phase induction motor is connected to a three-phase AC
          supply, a rotating magnetic field is set up in the …

          A      rotor.
          B      stator.
          C      armature.
          D      commutator.                                                                      (1)

1.11      In a three-phase forward-reverse motor-starter control circuit, the … contacts
          of each contactor prevent the forward and reverse contactors from being
          energised at the same time.

          A      N/O
          B      latching
          C      hold-in
          D      N/C interlocking                                                                 (1)

1.12      In an automatic sequence starter control circuit, the start button of motor 2 is
          replaced by a … to energise the contactor of the second motor after a
          pre-determined time period.

          A      N/O contact of an ON-delay timer
          B      N/C contact of an ON-delay timer
          C      N/O retain contact of MC1
          D      N/C interlocking contact of MC2                                                  (1)

Copyright reserved                                                             Please turn over

### Page 5

Electrical Technology: Power Systems           5                         DBE/November 2024
                                         NSC Confidential

1.13      A ladder logic diagram in PLC software is executed from …

          A      right to left and top to bottom.
          B      left to right and top to bottom.
          C      left to right and bottom to top.
          D      right to left and bottom to top.                                                 (1)

1.14      A device that is used to provide a delay in the operation of a PLC's program is
          known as a …

          A      transistor.
          B      relay.
          C      contactor.
          D      timer.                                                                           (1)

1.15      During the process of regenerative braking, a braking resistor is connected in
          the circuit to …

          A      decrease the charging rate of the capacitors.
          B      prevent the charging of the capacitors.
          C      dissipate the excessive regenerative energy.
          D      reduce the supply to the motor.                                                  (1)
                                                                                                  [15]

QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

2.1       Define the term workplace with reference to the Occupational Health and
          Safety Act, 1993 (Act 85 of 1993).                                                      (2)

2.2       Name TWO human rights in the workplace.                                                 (2)

2.3       Explain why poor ventilation is an unsafe condition in a workshop.                      (2)

2.4       State TWO types of victimisation by an employer that are forbidden.                     (2)

2.5       Explain why a person should not interfere with equipment in the workshop
          that is provided for safety.                                                            (2)
                                                                                                  [10]

Copyright reserved                                                             Please turn over

### Page 6

Electrical Technology: Power Systems           6                           DBE/November 2024
                                         NSC Confidential

QUESTION 3: RLC CIRCUITS

3.1       Explain the following terms with reference to RLC circuits:

          3.1.1       Inductive reactance                                                         (2)

          3.1.2       Bandwidth                                                                   (2)

3.2       FIGURE 3.2 below shows an RLC series circuit with a variable frequency
          supply. Answer the questions that follow.

                                  R         XL = 150         XC = 113,6

                                            VL = 3,45 V      VC = 2,61 V

                                             2,5 V/50 Hz

                                  FIGURE 3.2: RLC SERIES CIRCUIT

          Given:

          XL          = 150 Ω
          XC          = 113,6 Ω
          VT          = 2,5 V
          VL          = 3,45 V
          VC          = 2,61 V

          3.2.1       State whether the circuit represented in FIGURE 3.2 has a leading
                      or a lagging power factor.                                                  (1)

          3.2.2       Calculate the current through the inductor.                                 (3)

          3.2.3       Calculate the value of the inductor.                                        (3)

          3.2.4       Calculate the value of resistor R if the impedance Z = 106,42 Ω.            (3)

Copyright reserved                                                             Please turn over

### Page 7

Electrical Technology: Power Systems                7                                      DBE/November 2024
                                              NSC Confidential

          3.2.5       Complete the phasor diagram in FIGURE 3.2.5 below in your
                      ANSWER BOOK.

                                                                 IT         VR

                                            FIGURE 3.2.5: PHASOR DIAGRAM                                          (4)

          3.2.6       After decreasing the frequency, the current increased slightly.
                      Explain why this happened.                                                                  (3)

3.3       FIGURE 3.3 below shows an RLC parallel circuit and its impedance vs
          frequency response curve. Answer the questions that follow.

                                       IT           IR                 IL               IC
                                                                                      9,2 A
                      230 V                           R                     XL
                      50 Hz                                                                C
                                                     60 Ω                  25 Ω

                               Z

                                                    f1    fr          f2          f (Hz)

                     FIGURE 3.3: RLC PARALLEL CIRCUIT AND FREQUENCY
                                    RESPONSE CURVE

Copyright reserved                                                                             Please turn over

### Page 8

Electrical Technology: Power Systems            8                         DBE/November 2024
                                          NSC Confidential

          Given:

          VT       =   230 V
          IC       =   9,2 A
          R        =   60 Ω
          XL       =   25 Ω
          f        =   50 Hz

          3.3.1        Calculate the current through the resistor.                                (3)

          3.3.2        Calculate the capacitive reactance.                                        (3)

          3.3.3        Determine the total current. Give a reason for your answer.                (2)

          3.3.4        Calculate the Q-factor of the circuit                                      (3)

          3.3.5        Calculate the bandwidth of the circuit                                     (3)
                                                                                                  [35]

Copyright reserved                                                             Please turn over

### Page 9

Electrical Technology: Power Systems          9                           DBE/November 2024
                                        NSC Confidential

QUESTION 4: THREE-PHASE AC GENERATION

4.1       State TWO advantages of three-phase systems.                                            (2)

4.2       Refer to electricity generation at power stations in South Africa and answer
          the following questions:

          4.2.1       State the voltage AND frequency at which electricity is generated in
                      South Africa.                                                               (2)

          4.2.2       Name TWO energy sources, other than coal, used for electricity
                      generation in South Africa.                                                 (2)

          4.2.3       Explain the transmission process with reference to voltages in the
                      national grid.                                                              (3)

4.3       FIGURE 4.3 below shows the coil connection in a balanced three-phase
          generator. Answer the questions that follow.

                                                             L1

                                                             N

                                                             L2

                                                             L3

                        FIGURE 4.3: THREE-PHASE GENERATOR

          4.3.1       Identify the configuration of the coils in FIGURE 4.3 above.                (1)

          4.3.2       Draw the voltage waveforms of a three-phase AC generator.                   (4)

Copyright reserved                                                             Please turn over

### Page 10

Electrical Technology: Power Systems          10                         DBE/November 2024
                                         NSC Confidential

4.4       FIGURE 4.4 below shows a balanced three-phase load powered by a
          three-phase alternator. The alternator provides a line voltage of 400 V to the
          load with a power factor of 0,85. The apparent power of the system is 14 kVA.
          Answer the questions that follow.

                      Alternator          S = 14 kVA                LOAD
                                         L1
                                                IL                          IPH

                            N
                                       VL= 400 V
                                                                   ZPH

                                         L2
                                         L3
                                                                   pf = 0,85

                            FIGURE 4.4: THREE-PHASE SYSTEM

          Given:

          VL      =    400 V
          S       =    14 kVA
          pf      =    0,85

          Calculate the:

          4.4.1        Active power                                                               (3)

          4.4.2        Line current                                                               (3)

          4.4.3        Phase current                                                              (3)

          4.4.4        Phase impedance                                                            (3)

          4.4.5        Phase angle                                                                (3)

Copyright reserved                                                             Please turn over

### Page 11

Electrical Technology: Power Systems             11                     DBE/November 2024
                                            NSC Confidential

4.5       FIGURE 4.5 below shows how a three-phase supply is connected to a
          three-phase load.

                                       L1

                           SUPPLY
                                       L2
                                                                       LOAD
                                       L3

                           FIGURE 4.5: THREE-PHASE SYSTEM

          4.5.1       State ONE method, other than capacitors, used for power factor
                      correction.                                                              (1)

          4.5.2       Redraw FIGURE 4.5 above and show how a three-phase power
                      factor correcting capacitor bank will be connected to this system.       (3)

          4.5.3       State the preferred wattmeter method that would be used to
                      measure the total power of the load. Motivate your answer.               (2)
                                                                                               [35]

Copyright reserved                                                          Please turn over

### Page 12

Electrical Technology: Power Systems         12                             DBE/November 2024
                                        NSC Confidential

QUESTION 5: THREE-PHASE TRANSFORMERS

5.1       Explain the function of transformers with reference to voltage and current.              (2)

5.2       Briefly describe the principle on which a transformer operates.                          (2)

5.3       Refer to FIGURE 5.3 below and answer the questions that follow.

                                                                 Windings

                                                                     Core

                       FIGURE 5.3: THREE-PHASE TRANSFORMER

          5.3.1       Identify the type of core construction in FIGURE 5.3 above.                  (1)

          5.3.2       Explain the purpose of the laminated iron-core in a transformer.             (2)

          5.3.3       Compare the construction of a three-phase transformer with
                      reference to a core-type and a shell-type transformer.                       (2)

          5.3.4       Describe how hysteresis losses occur in the iron core of a
                      transformer.                                                                 (3)

Copyright reserved                                                              Please turn over

### Page 13

Electrical Technology: Power Systems              13                  DBE/November 2024
                                             NSC Confidential

5.4      FIGURE 5.4 below shows a 200 kVA three-phase transformer. The primary
         line voltage is 6 kV and the secondary line voltage is 380 V with 80 turns on
         the secondary side.

                                               N1         N2 = 80

                     VL1 = 6 kV
                                                                    VL 2 = 380 V

                                                                          N

                           FIGURE 5.4: THREE-PHASE TRANSFORMER

         Given:

         S                 = 200 kVA
         VL1               = 6 kV
         VL2               = 380 V
         N2                = 80

         Calculate the following:

         5.4.1             Secondary phase voltage                                            (3)

         5.4.2             Number of primary turns                                            (3)

         5.4.3             Turns ratio                                                        (3)

         5.4.4             Supply current at full load                                        (3)

5.5       State TWO common defects which are likely to occur in transformers due to
          overloading.                                                                        (2)

Copyright reserved                                                         Please turn over

### Page 14

Electrical Technology: Power Systems            14                      DBE/November 2024
                                           NSC Confidential

5.6       FIGURE 5.6 below shows the schematic diagram of a transformer. Answer
          the questions that follow.

                                       A

                          Buchholz
                            relay                                      Breather

                                                                   Cooling tubes

                                                                   Cable end box

                                 FIGURE 5.6: TRANSFORMER

          5.6.1       Identify component A in FIGURE 5.6 above.                                (1)

          5.6.2       State ONE function of the dielectric oil in a transformer besides
                      providing insulation between the windings and case.                      (1)

          5.6.3       Briefly describe the function of the Buchholz relay in an
                      oil-immersed transformer.                                                (2)
                                                                                               [30]

Copyright reserved                                                          Please turn over

### Page 15

Electrical Technology: Power Systems         15                            DBE/November 2024
                                        NSC Confidential

QUESTION 6: THREE-PHASE MOTORS AND STARTERS
6.1       State TWO typical applications (uses) of a three-phase induction motor in
          a workshop.                                                                              (2)
6.2       FIGURE 6.2 below shows the terminal box of a three-phase induction motor
          and an insulation resistance tester indicating a reading of 100 kΩ. Answer the
          questions that follow.

                     U1          V1          W1

                                                            E

                                                                       100 kΩ
                     W2          U2          V2
                                                                      Insulation
                                                                  resistance tester

                                FIGURE 6.2: TERMINAL BOX
          6.2.1       State why this motor is NOT safe for use.                                    (1)

          6.2.2       Explain the danger of the fault in FIGURE 6.2 above when the
                      motor is powered.                                                            (1)

          6.2.3       Redraw the terminals of the coils in your ANSWER BOOK and
                      indicate how you would place the connecting plates/bars to
                      connect this motor in delta.                                                 (3)
6.3       A three-phase induction motor with six poles is connected to a
          400 V/50 Hz supply. The motor experiences a slip of 6% at full load.

          Given:

          f    = 50 Hz
          VL   = 400 V
          Slip = 6%

          Calculate the:

          6.3.1       Pole pairs per phase                                                         (3)

          6.3.2       Synchronous speed                                                            (3)

          6.3.3       Rotor speed                                                                  (3)

Copyright reserved                                                              Please turn over

### Page 16

Electrical Technology: Power Systems             16                           DBE/November 2024
                                            NSC Confidential

6.4       FIGURE 6.4 below shows the control circuit of an automatic star-delta motor
          starter with contactor T set to 5 seconds. Answer the questions that follow.

                  L1

                       O/L
                       N/C

                        Stop

                       Start            MC 1
                                        N/O

                                                                      T               T
                                                                     N/C             N/O

                                                                   MC 3           MC 2
                                                                   N/C            N/C

                       MC 1             T                MC 2          MC 3

                   N
              FIGURE 6.4: AUTOMATIC STAR-DELTA CONTROL CIRCUIT

          6.4.1          State the function of MC1N/O.                                                (1)

          6.4.2          Explain the function of contactor T.                                         (2)

          6.4.3          Explain why it is safe to assume that MC2 will be the contactor
                         connecting the motor coils in star in the main circuit.                      (2)

          6.4.4          Describe the operation of the circuit 5 seconds after the start button
                         is pressed.                                                                  (3)

Copyright reserved                                                                 Please turn over

### Page 17

Electrical Technology: Power Systems        17                        DBE/November 2024
                                       NSC Confidential

6.5       The name plate of a three-phase induction motor indicates that it is able to
          power a 30 kW mechanical load when connected to a 400 V supply. The
          motor has a power factor of 0,87. The total losses were determined as 5 kW.

          Given:

          POUT        = 30 kW
          VL          = 400 V
          pf          = 0,87
          losses      = 5 kW

          Calculate the:

          6.5.1       Efficiency                                                             (3)

          6.5.2       Line current                                                           (3)

          6.5.3       Reactive power                                                         (5)
                                                                                             [35]

Copyright reserved                                                        Please turn over

### Page 18

Electrical Technology: Power Systems            18                    DBE/November 2024
                                           NSC Confidential

QUESTION 7: PROGRAMMABLE LOGIC CONTROLLERS (PLCs)

7.1       Refer to the programmed scan cycle of a PLC and answer the questions that
          follow.

          7.1.1       State the TWO steps, other than the process scan, of a
                      programmed scan cycle.                                                 (2)

          7.1.2       Explain the process scan.                                              (3)

7.2       Refer to FIGURE 7.2 below of the symbol of a logic gate and answer the
          questions that follow.

                                       A
                                                                  X
                                       B

                                       FIGURE 7.2: LOGIC GATE

          7.2.1       Identify the logic gate in FIGURE 7.2 above.                           (1)

          7.2.2       Draw the ladder logic of this logic gate.                              (3)

          7.2.3       Complete the truth table in FIGURE 7.2.3 below by writing down
                      only the state of the output in the ANSWER BOOK.

                                  A                 B        OUTPUT
                                  0                 0          (W)
                                  0                 1           (X)
                                  1                 0           (Y)
                                  1                 1           (Z)
                                       FIGURE 7.2.3: TRUTH TABLE                             (4)

Copyright reserved                                                        Please turn over

### Page 19

Electrical Technology: Power Systems              19                       DBE/November 2024
                                             NSC Confidential

7.3       Refer to inputs on a PLC and answer the questions that follow.
          7.3.1        Name TWO categories of input devices.                                      (2)

          7.3.2        Name TWO applications (uses) of a level sensor.                            (2)

          7.3.3        Differentiate between the application of an inductive proximity
                       sensor and a capacitive proximity sensor.                                  (4)

7.4       FIGURE 7.4 below shows the relay diagram of a forward-reverse motor
          starter. Redraw and complete the PLC ladder logic diagram in FIGURE 7.4.1
          that will execute the same function in a PLC system in the ANSWER BOOK.

                                       L
                                       O/L
                                       N/C

                              STOP

                              START                        START
                               FWD                 MC1      REV    MC2
                                                   N/O             N/O
                                 MC2                       MC1
                                 N/C                        N/C
                               MC1                        MC2
                               FWD                        REV

                                       N
                                                                                                  (8)
                      FIGURE 7.4: FORWARD-REVERSE CONTROL CIRCUIT

                     O/L       STOP

                       FIGURE 7.4.1: PLC LADDER LOGIC DIAGRAM

Copyright reserved                                                             Please turn over

### Page 20

Electrical Technology: Power Systems             20                               DBE/November 2024
                                            NSC Confidential

7.5       FIGURE 7.5 below shows a variable frequency drive (VFD) circuit. Study the
          circuit and answer the questions that follow.

                                                       1           2               3
                                                       1
                                                       2
                                                       3
                                            Variable
                                  +        frequency
      A                                       drive
                                                                                                Motor
                                             circuit   4
                                                       5
                                                       6
                                                       4           5                   6

                     B                 C                       DC - to - AC Inverter

                  FIGURE 7.5: VARIABLE FREQUENCY DRIVE (VFD) CIRCUIT

          7.5.1       Label blocks A, B and C.                                                        (3)

          7.5.2       State TWO types of motors used with a VSD.                                      (2)

          7.5.3       Explain the function of the DC-to-AC inverter.                                  (3)

          7.5.4       Explain pulse width modulation (PWM) when referring to VSD.                     (3)
                                                                                                      [40]

                                                                                           TOTAL:     200

Copyright reserved

### Page 21

Electrical Technology: Power Systems                                                DBE/November 2024
                                                NSC Confidential

                                             FORMULA SHEET
RLC CIRCUITS                                              THREE-PHASE AC GENERATION
P = V I Cos θ                                             STAR
XL = 2πfL                                                 VL = √3 VPH
        1                                                 VPH = IPH ZPH
XC =
      2πfC                                                IL = IPH
          1                        f1 + f2
  fr =                OR    fr =                          DELTA
       2π√LC                         2
       fr
BW =                  OR    BW = f2 - f1                  VL = VPH
        Q
SERIES                                                    VPH = IPH ZPH
VR = IR                                                   IL = √3 IPH
VL = IXL                                                  POWER
VC = IXC                                                  S(Papp ) = √3 VL IL

       VT                                                 Q(Pr ) = √3 VL IL Sin θ
IT =               OR       IT = IR = IC = IL
       Z                                                  P = √3 VL IL Cos θ
                                                                  P
Z = √R2 + (XL - XC )2                                     Cos θ =
                                                                  S
VT = √VR 2 + (VL - VC )2        OR        VT = IZ         EFFICIENCY
            R                                   VR             POUT
Cos θ =                    OR           Cos θ =           η=        × 100
            Z                                   VT              PIN
       XL XC VL VC 1    L
Q=       =   =   =  = √
       R   R   VT VT R C                                  TWO-WATTMETER METHOD

PARALLEL                                                  PT = P1 + P2
VT = VR = VC = VL
                                                                        P1 - P2
     VT                                                   tan θ = √3 (          )
IR =                                                                    P1 + P2
      R
     VT
IC =                                                      THREE-WATTMETER METHOD
     XC
     VT
IL =                                                      PT = P1 + P2 + P3
     XL

IT = √I2R + (IL - IC )2
       VT
Z=
       IT
            IR
Cos θ =
            IT
       R   R
Q=       =
       XL XC

Copyright reserved

### Page 22

Electrical Technology: Power Systems                                     DBE/November 2024
                                       NSC Confidential

THREE-PHASE TRANSFORMERS                  THREE-PHASE MOTORS AND STARTERS
STAR                                      STAR
VL = √3 VPH                               VL = √3 VPH
IL = IPH                                  IL = IPH

DELTA                                     DELTA
VL = VPH                                  VL = VPH
IL = √3 IPH                               IL = √3 IPH

POWER                                     POWER
S(Papp ) = √3 VL IL                       S(Papp ) = √3 VL IL

Q(Pr ) = √3 VL IL Sin θ                   Q(Pr ) = √3 VL IL Sin θ

P = √3 VL IL Cos θ                        P = √3 VL IL Cos θ
        P
Cos θ =                                   P = √3 VL IL Cos θ η
        S
VPH(1) N1 IPH(2)                                    P
      =   =                               Cos θ =
VPH(2) N2 IPH(1)                                    S
                     N1
Turns ratio: TR =                         EFFICIENCY
                     N2
                                             PIN - losses
                                          η=              × 100
                                                  PIN
                                                  POUT
                                          η=                × 100
                                             POUT + losses
                                             POUT
                                          η=        × 100
                                              PIN

                                          SPEED
                                                            poles per phase
                                          (pole pairs) p=
                                                                   2
                                                 60 × f
                                          ns =
                                                   p
                                                          n s - nr
                                          Per unit slip =
                                                             ns
                                                    ns - nr
                                          % Slip =          × 100
                                                       ns
                                          nr = ns (1 - % slip)
                                          Slip = ns - nr

Copyright reserved

## Related documents

- [Electrical Technology Nov 2024 (Power Systems) Afr](https://www.hlayiso.com/library/electrical-technology-nov-2024-power-systems-afr/5f2b4850-fffb-4024-8f24-d74bd8677a25) — Electrical Technology · QP · 2024 · Afr
- [Electrical Technology May-June 2024 (Power Systems) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/0d8d71f4-5725-40ea-9e29-a19e1c8a7867) — Electrical Technology · QP · 2024 · Eng
- [Electrical Technology May-June 2024 (Digital) Eng](https://www.hlayiso.com/library/grade-12-electrical-technology-2024-nsc-june-exam-question-paper-english/2b227e9b-0513-468e-8b1a-d4df808071cd) — Electrical Technology · QP · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Power Systems Afrikaans](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-afrikaans/1a395c97-b838-42e6-9bd6-30a85a714b11) — Electrical Technology · Memo · 2024 · Afr
- [ELEC TECH GR12 MEMO SEPT2024 Power Systems English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-english/bea78337-b137-406a-9b4a-c6e631a84c9d) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Electronics English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-electronics-english/c80784c8-a9c8-49f8-b740-a29558fe2de9) — Electrical Technology · Memo · 2024 · Eng

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [ELECTRIC TECH (Digital) MEMO GR12 SEPT 2025 ENG watermark](https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d) — Memo · 2025 · Eng
- [Electrical Technology P1 (Electronics) (English) June 2025 Possible Answers](https://www.hlayiso.com/library/electrical-technology-p1-electronics-english-june-2025-possible-answers/4302563e-89b7-4f54-8a21-63b2020e985f) — Memo · 2025 · Eng
- [Electrical Technology Nov 2025 (Digital) MG Afr](https://www.hlayiso.com/library/grade-12-electrical-technology-2025-nsc-november-exam-memorandum/3b862a0c-6a87-4296-b5b6-09b072c7d1e9) — Memo · 2025 · Afr
- [ELEC TECH GR12 MEMO SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-digital-english/cb603860-b00d-40c2-a36b-aa5e97b7d1e5) — Memo · 2024 · Eng
- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
