# Electrical Technology Grade 12 Gauteng June 2025 QP (Eng)

> Grade 12 Electrical Technology question paper from the Gauteng June Exam 2025 (English), 33 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/electrical-technology-power-systems-english-june-2025-question-paper/5422e67a-03a4-4202-ba9b-1b9ec9872537
- Updated: 2026-09-27
- Subject: Electrical Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2025
- Exam period: Gauteng June Exam
- Curriculum: CAPS
- Pages: 33

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Electrical Technology](https://www.hlayiso.com/library/grade-12/electrical-technology) › [Electrical Technology Grade 12 Gauteng June 2025 QP (Eng)](https://www.hlayiso.com/library/electrical-technology-power-systems-english-june-2025-question-paper/5422e67a-03a4-4202-ba9b-1b9ec9872537)

## About this document

Electrical Technology · Grade 12 · Gauteng June Exam · 2025 · English. Question paper, 33 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

JUNE EXAMINATION
  JUNIE EKSAMEN
 GRADE/GRAAD 12
        2025

ELECTRICAL TECHNOLOGY:
ELEKTRIESE TEGNOLOGIE:
    POWER SYSTEMS
     KRAGSTELSELS

                                        TIME/TYD:   3 hours/uur

                                        MARKS/PUNTE: 200

 15 pages + a 2-page formula sheet
 15 bladsye + 'n 2-bladsy formuleblad

                                                      Please turn over
                                                      Blaai om asseblief

### Page 2

ELECTRICAL TECHNOLOGY:                        2
                                        POWER SYSTEMS                  GR12 0625

INSTRUCTIONS AND INFORMATION

1.   This question paper consists of SIX questions.

2.   Answer ALL the questions.

3.   Sketches and diagrams must be large, neat and FULLY LABELLED.

4.   Show ALL calculations and round-off answers correctly to TWO decimal places.

5.   Number the answers correctly according to the numbering system used in this
     question paper.

6.   A non-programmable calculator may be used.

7.   Calculations must include:

     7.1   Formulae and manipulations where needed

     7.2   Correct replacement of values

     7.3   Correct answer and relevant units where applicable

8.   A formula sheet is attached at the end of this question paper.

9.   Write neatly and legibly.

                                                                             Please turn over

### Page 3

ELEKTRIESE TEGNOLOGIE:                           2
                                       KRAGSTELSELS                    GR12 0625

INSTRUKSIES EN INLIGTING

1.   Hierdie vraestel bestaan uit SES vrae.

2.   Beantwoord AL die vrae.

3.   Sketse en diagramme moet groot, netjies en VOLLEDIG BENOEM wees.

4.   Toon ALLE berekeninge en rond antwoorde korrek tot TWEE desimale plekke af.

5.   Nommer die antwoorde korrek volgens die nommering wat in hierdie vraestel gebruik is.

6.   Jy mag ŉ nie-programmeerbare sakrekenaar gebruik.

7.   Berekeninge moet die volgende insluit:

     7.1   Formules en manipulasies waar nodig

     7.2   Korrekte vervanging van waardes

     7.3   Korrekte antwoord en relevante eenhede waar van toepassing

8.   ŉ Formuleblad is aan die einde van hierdie vraestel aangeheg.

9.   Skryf netjies en leesbaar.

                                                                              Blaai om asseblief

### Page 4

ELECTRICAL TECHNOLOGY:                          3
                                            POWER SYSTEMS                  GR12 0625

QUESTION 1: MULTIPLE-CHOICE QUESTIONS

Various options are provided as possible answers to the following questions. Choose the
answer and write only the letter (A – D) next to the question numbers (1.1 to 1.15)
in the ANSWER BOOK, e.g. 1.16 A.

1.1    An attempt to numerically determine the probabilities of adverse events and
       potential losses if they occur is known as …

       A      risk analysis.
       B      quantitative risk analysis.
       C      qualitative risk analysis.
       D      dangerous practices.                                                              (1)

1.2    The opposition of a capacitor to the flow of alternating current in an RLC circuit
       is the …

       A      inductive reactance.
       B      impedance.
       C      capacitive reactance.
       D      inductance.                                                                       (1)

1.3    When the frequency of an RLC circuit increases, the resistance will …

       A      also increase.
       B      decrease.
       C      remain the same.
       D      double its value.                                                                 (1)

1.4    In an RLC parallel circuit, the current through a capacitor will … when the
       frequency increases.

       A      remain the same
       B      decrease
       C      increase
       D      be zero                                                                           (1)

1.5    The correct method to connect a wattmeter is by connecting the voltage coil in
       … with the load.

       A      parallel, and the current coil in series
       B      series, and the current coil in series
       C      parallel, and the current coil in parallel
       D      series, and the current coil in parallel                                          (1)

                                                                                  Please turn over

### Page 5

ELEKTRIESE TEGNOLOGIE:                              3
                                        KRAGSTELSELS                     GR12 0625

VRAAG 1: MEERVOUDIGEKEUSE-VRAE

Verskillende opsies word as moontlike antwoorde op die volgende vrae gegee. Kies die
antwoord en skryf slegs die letter (A – D) langs die vraagnommers (1.1 tot 1.15) in die
ANTWOORDBOEK neer, bv. 1.16 A.

1.1     ŉ Poging om die waarskynlikhede van nadelige gebeurtenisse en die potensiële
        verliese numeries te bepaal staan bekend as …

        A     risiko-analise.
        B     kwantitatiewe risiko-analise.
        C     kwalitatiewe risiko-analise.
        D     gevaarlike praktyke.                                                               (1)

1.2     Die opposisie van ŉ kapasitor teen die vloei van wisselstroom in ŉ RLC-
        stroombaan is die …

        A     induktiewe reaktansie.
        B     impedansie.
        C     kapasitiewe reaktansie.
        D     induktansie.                                                                       (1)

1.3     Wanneer die frekwensie van ŉ RLC-stroombaan toeneem, sal die weerstand ...

        A     ook toeneem.
        B     verminder.
        C     dieselfde bly.
        D     se waarde verdubbel.                                                               (1)

1.4     In ŉ RLC-parallelkring sal die stroom deur ŉ kapasitor … wanneer die
        frekwensie toeneem.

        A     dieselfde bly
        B     afneem
        C     toeneem
        D     nul wees                                                                           (1)

1.5     Die korrekte metode om ŉ wattmeter te verbind, is om die spanningspoel in …
        met die las te verbind.

        A     parallel en die stroomspoel in serie
        B     serie en die stroomspoel in serie
        C     parallel en die stroomspoel in parallel
        D     serie en die stroomspoel in parallel                                               (1)

                                                                                  Blaai om asseblief

### Page 6

ELECTRICAL TECHNOLOGY:                               4
                                       POWER SYSTEMS                       GR12 0625

1.6    The active current in a three-phase system is:

       A     I Cos θ
       B     I Sin θ
       C     I Tan θ
       D     I                                                                                  (1)

1.7    Self-contained units controlled from main control centres are called …

       A     switchgear.
       B     distribution networks.
       C     substations.
       D     power stations.                                                                    (1)

1.8    After adding power factor correcting capacitors in parallel with a load, the power
       factor increases from 0,6 to 0,9. With the load unchanged, the current drawn
       from the supply will …

       A     increase.
       B     decrease.
       C     remain the same.
       D     double.                                                                            (1)

1.9    Air Natural (AN) is a cooling method used for …

       A     dry transformers.
       B     oil-immersed transformers.
       C     relays.
       D     contactors.                                                                        (1)

1.10   The function of transformers in distribution networks is to …

       A     increase the voltage to the required value.
       B     change AC voltages to the required DC voltage.
       C     reduce the voltage to the required value.
       D     generate the required voltage.                                                     (1)

1.11   The construction of a three-phase shell-type transformer consists of a core
       with …

       A     three limbs, with coils wound around all three limbs.
       B     five limbs, with coils wound around the three middle limbs.
       C     five limbs, with coils wound around all five limbs.
       D     three limbs, with coils wound around the two outer limbs.                          (1)

                                                                                 Please turn over

### Page 7

ELEKTRIESE TEGNOLOGIE:                               4
                                        KRAGSTELSELS                        GR12 0625

1.6    Die aktiewe stroom in ŉ driefase-stelsel is:

       A     I Cosø
       B     I Sinø
       C     I Tanø
       D     I                                                                                    (1)

1.7    Selfonderhoudende eenhede wat vanaf hoofbeheersentrums beheer word, word
       … genoem.

       A     skakeltoerusting
       B     verspreidingsnetwerke
       C     substasies
       D     kragstasies                                                                          (1)

1.8    Nadat drywingsfaktor-verbeteringkapasitors in parallel met ŉ las gekoppel is,
       verhoog die drywingsfaktor van 0,6 tot 0,9. Indien die las dieselfde bly, sal die
       stroomvloei wat vanaf die toevoer getrek word ...

       A     toeneem.
       B     afneem.
       C     dieselfde bly.
       D     verdubbel.                                                                           (1)

1.9    Natuurlike lug ("Air Natural – AN") is ŉ verkoelingsmetode wat vir … gebruik
       word.

       A     droë transformators
       B     onderolie transformators
       C     relê
       D     kontaktors                                                                           (1)

1.10   Die funksie van transformators in verspreidingsnetwerke is om …

       A     die spanning tot die vereiste waarde te verhoog.
       B     die WS-spanning na die vereiste GS-spanning te verander.
       C     die spanning tot die vereiste waarde te verminder.
       D     die vereiste spanning op te wek.                                                     (1)

1.11   Die konstruksie van ŉ driefase-dop-tipe transformator bestaan uit ŉ kern met ...

       A     drie bene, met spoele om al drie bene gedraai.
       B     vyf bene, met spoele om die middelste drie bene gedraai.
       C     vyf bene, met spoele om al vyf bene gedraai.
       D     drie bene, met spoele om die twee buitenste bene gedraai.                            (1)

                                                                                   Blaai om asseblief

### Page 8

ELECTRICAL TECHNOLOGY:                          5
                                         POWER SYSTEMS                    GR12 0625

1.12   The purpose of a no-volt relay is to ...

       A     allow a motor to automatically start after power is restored.
       B     increase the voltage of a three-phase motor.
       C     prevent a motor from automatically starting when power is restored.
       D     monitor the current drawn by a motor.                                            (1)

1.13   Power in an induction motor is transferred from the …

       A     rotor to the stator through mutual induction.
       B     stator to the rotor through slip rings.
       C     stator to the rotor through self-induction.
       D     rotor to the stator through self-induction.                                      (1)

1.14   The moment an induction motor starts, the … is at maximum and decreases as
       the motor speed increases.

       A     slip
       B     rotor speed
       C     full-load speed
       D     momentum                                                                         (1)

1.15   The stator windings of a three-phase induction motor may be connected …

       A     in star only.
       B     in star or delta.
       C     in delta only.
       D     None of the above-mentioned.                                                     (1)
                                                                                             [15]

QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY

2.1    Name TWO general duties of employees at the workplace.                                 (2)

2.2    Define health and safety equipment.                                                    (2)

2.3    State TWO characteristics or moral principles related to work ethics.                  (2)

2.4    Define the term danger with reference to the Occupational Health and Safety
       Act, 1993 (Act 85 of 1993).                                                            (2)

2.5    Explain the ideal location of the master switch in a workshop and its purpose.         (2)
                                                                                             [10]

                                                                                Please turn over

### Page 9

ELEKTRIESE TEGNOLOGIE:                             5
                                         KRAGSTELSELS                    GR12 0625

1.12   Die doel van ŉ nul-volt-relê is om ...

       A     ŉ motor outomaties te laat begin nadat krag herstel is.
       B     die spanning van ŉ driefase motor te verhoog.
       C     te verhoed dat ŉ motor outomaties aanskakel wanneer krag herstel is.
       D     die stroom wat deur ŉ motor getrek word te monitor.                                 (1)

1.13   Drywing in ŉ induksiemotor word vanaf die … oorgedra.

       A     rotor na die stator deur wedersydse induksie
       B     stator na die rotor deur sleepringe
       C     stator na die rotor deur selfinduksie
       D     rotor na die stator deur selfinduksie                                               (1)

1.14   Die oomblik wat ŉ induksiemotor aanskakel, is die … by maksimum en neem dit
       af soos wat die motorspoed toeneem.

       A     glip
       B     rotorspoed
       C     vollasspoed
       D     momentum                                                                            (1)

1.15   Die statorwikkelings van ŉ driefase-induksiemotor kan ... gekoppel word.

       A     slegs in ster
       B     in ster of delta
       C     slegs in delta
       D     Geeneen van die bogenoemde nie.                                                     (1)
                                                                                                [15]

VRAAG 2: BEROEPSGESONDHEID EN VEILIGHEID

2.1    Noem TWEE algemene pligte van werknemers in die werkplek.                                 (2)

2.2    Definieer gesondheids- en veiligheidstoerusting.                                          (2)

2.3    Noem TWEE eienskappe of morele beginsels wat verband hou met werksetiek.                  (2)

2.4    Definieer die term gevaar met verwysing na die Wet op Beroepsgesondheid en -
       veiligheid, 1993 (Wet 85 van 1993).                                                       (2)

2.5    Verduidelik die ideale ligging van die hoofskakelaar in ŉ werkswinkel en die doel
       daarvan.                                                                                  (2)
                                                                                                [10]

                                                                                  Blaai om asseblief

### Page 10

ELECTRICAL TECHNOLOGY:                               6
                                     POWER SYSTEMS                     GR12 0625

QUESTION 3: RLC CIRCUITS

3.1    Name TWO factors that would influence the reactance of a capacitor.                    (2)

3.2    State the phase relationship between the current and voltage in a pure
       inductive AC circuit.                                                                  (2)

3.3    Define the following with reference to RLC circuits connected across an
       alternating voltage supply:

       3.3.1    Reactance                                                                     (2)

       3.3.2    Impedance                                                                     (2)

3.4    Describe what the term in phase means with reference to the relationship
       between the applied voltage and current in an RLC circuit connected to an AC
       supply.                                                                                (3)

3.5    A series circuit with a resistance of 1 000 Ω; inductance 200 mH and
       capacitance of 4 μF is connected across a 120 V / 60 Hz supply.

       Refer to FIGURE 3.5 below and answer the questions that follow.

                            FIGURE 3.5: SERIES RLC CIRCUIT
       Given:

       R = 1 000 Ω
       L = 200 mH
       C = 4 μF
       V = 120 V
       f = 60 Hz

       Calculate the:

       3.5.1    Reactance of the inductor                                                     (3)

       3.5.2    Reactance of the capacitor                                                    (3)

                                                                                 Please turn over

### Page 11

ELEKTRIESE TEGNOLOGIE:                            6
                                     KRAGSTELSELS                    GR12 0625

VRAAG 3: RLC-KRINGBANE

3.1    Noem TWEE faktore wat die reaktansie van ŉ kapasitor sal beïnvloed.                  (2)

3.2    Noem die fase verhouding tussen die stroom en spanning in ŉ suiwer
       induktiewe WS-stroombaan.                                                            (2)

3.3    Definieer die volgende met verwysing na RLC-stroombane wat oor ŉ
       wisselspanningstoevoer gekoppel is:

       3.3.1    Reaktansie                                                                  (2)

       3.3.2    Impedansie                                                                  (2)

3.4    Beskryf wat die term gelykfasig (in fase) beteken met verwysing na die
       verwantskap tussen die toegepaste spanning en stroom in ŉ RLC-kringbaan
       wat aan ŉ WS-toevoer gekoppel is.                                                    (3)

3.5    ŉ Seriestroombaan met weerstand van 1 000 Ω; induktansie van 200 mH en
       kapasitansie van 4 μF word oor ŉ 120 V / 60 Hz-toevoer gekoppel.

       Verwys na FIGUUR 3.5 hieronder en beantwoord die vrae wat volg.

                          FIGUUR 3.5: RLC-SERIEKRINGBAAN
       Gegee:

       R = 1 000 Ω
       L = 200 mH
       C = 4 μF
       V = 120 V
       f = 60 Hz

       Bereken die:

       3.5.1    Reaktansie van die induktor                                                 (3)

       3.5.2    Reaktansie van die kapasitor                                                (3)

                                                                             Blaai om asseblief

### Page 12

ELECTRICAL TECHNOLOGY:                           7
                                       POWER SYSTEMS                      GR12 0625

      3.5.3    Circuit impedance                                                            (3)

      3.5.4    Circuit current                                                              (3)

3.6   Refer to FIGURE 3.6 below and answer the questions that follow.

                          FIGURE 3.6: RLC PARALLEL CIRCUIT

      Given:

      I = 13 A
      I =4A
      X = 10 Ω
      V = 120 V
      f = 30 Hz

      3.6.1    Calculate the current flowing through the capacitor.                         (3)

      3.6.2    Calculate the total current flowing through the circuit.                     (3)

      3.6.3    Calculate the power factor.                                                  (3)

      3.6.4    State, with a reason, whether the current is leading or lagging the
               voltage.                                                                     (2)

                                                                               Please turn over

### Page 13

ELEKTRIESE TEGNOLOGIE:                           7
                                     KRAGSTELSELS                     GR12 0625

      3.5.3    Stroombaan impedansie                                                       (3)

      3.5.4    Stroom in die stroombaan                                                    (3)

3.6   Verwys na FIGUUR 3.6 hieronder en beantwoord die vrae wat volg.

                          FIGUUR 3.6: RLC-PARALLELKRING

      Gegee:

      I = 13 A
      I =4A
      X = 10 Ω
      V = 120 V
      f = 30 Hz

      3.6.1    Bereken die stroom wat deur die kapasitor vloei.                            (3)

      3.6.2    Bereken die totale stroom wat deur die stroombaan vloei.                    (3)

      3.6.3    Bereken die drywingsfaktor.                                                 (3)

      3.6.4    Noem, met ŉ rede, of die stroom die spanning voorloop of naloop.            (2)

                                                                            Blaai om asseblief

### Page 14

ELECTRICAL TECHNOLOGY:                              8
                                        POWER SYSTEMS                      GR12 0625

3.7    Refer to FIGURE 3.7 below and answer the questions that follow.

                          FIGURE 3.7: RESONANT RLC CIRCUIT

       Given:

       R = 6 kΩ
       L = 22 mH
       X = 691,15 Ω
       V = 600 V
       f = 5 kHz

       3.7.1    Calculate the quality factor of the circuit.                                     (3)

       3.7.2    Calculate the bandwidth.                                                         (3)

       3.7.3    Calculate the value of the capacitor.                                            (3)

       3.7.4    Define the term selectivity with reference to resonant circuits.                 (2)
                                                                                                [45]

QUESTION 4: THREE-PHASE AC GENERATION

4.1    State TWO advantages of improved power factor correction to the consumer.                 (2)

4.2    State the difference between a wattmeter and a kilowatt-hour meter.                       (2)

4.3    State the size of the angles between the phases of a balanced three-phase
       AC generated waveform.                                                                    (1)

                                                                                   Please turn over

### Page 15

ELEKTRIESE TEGNOLOGIE:                            8
                                      KRAGSTELSELS                      GR12 0625

3.7    Verwys na FIGUUR 3.7 hieronder en beantwoord die vrae wat volg.

                     FIGUUR 3.7: RESONANTE RLC-STROOMBAAN

       Gegee:

       R = 6 kΩ
       L = 22 mH
       X = 691,15 Ω
       V = 600 V
       f = 5 kHz

       3.7.1    Bereken die kwaliteitsfaktor van die stroombaan.                             (3)

       3.7.2    Bereken die bandwydte.                                                       (3)

       3.7.3    Bereken die waarde van die kapasitor.                                        (3)

       3.7.4    Definieer die term selektiwiteit met verwysing na resonante
                stroombane.                                                                  (2)
                                                                                            [45]

VRAAG 4: DRIEFASE-WS-OPWEKKING

4.1    Noem TWEE voordele van arbeidsfaktorverbetering vir die verbruiker.                   (2)

4.2    Noem die verskil tussen ŉ wattmeter en ŉ kilowatt-uurmeter.                           (2)

4.3    Noem die grootte van die hoeke tussen die fases van ŉ gebalanseerde
       driefase WS-gegenereerde golfvorm.                                                    (1)

                                                                              Blaai om asseblief

### Page 16

ELECTRICAL TECHNOLOGY:                            9
                                     POWER SYSTEMS                     GR12 0625

4.4   Define the following terms:

      4.4.1    Neutral                                                                     (2)

      4.4.2    Power factor                                                                (2)

4.5   Calculate the phase voltage in a star-connected three-phase system if the line
      voltage is 380 V.                                                                    (3)

4.6   With reference to three-phase power generation:

      4.6.1    Explain the transmission process with reference to voltages in the
               national grid.                                                              (3)

      4.6.2    Explain the advantage of connecting a three-phase alternator in star.       (2)

4.7   Explain how copper losses are reduced in overhead transmission.                      (2)

4.8   A 380 V three-phase system supplies a star-connected inductive load. The
      input power to the load is 10,53 kW with a lagging power factor of 0,8.

      Given:

      V = 380 V
      P = 10,53 kW
      Cos θ = 0,8 lagging

      Calculate the:

      4.8.1    Phase voltage                                                               (3)

      4.8.2    Line current to the load                                                    (3)

      4.8.3    Phase angle                                                                 (3)

                                                                             Please turn over

### Page 17

ELEKTRIESE TEGNOLOGIE:                             9
                                      KRAGSTELSELS                     GR12 0625

4.4   Definieer die volgende terme:

      4.4.1    Neutraal                                                                       (2)

      4.4.2    Drywingsfaktor                                                                 (2)

4.5   Bereken die fasespanning in ŉ stergekoppelde driefasestelsel as die
      lynspanning 380 V is.                                                                   (3)

4.6   Met verwysing na driefase-kragopwekking:

      4.6.1    Verduidelik die transmissieproses met verwysing na spanning in die
               nasionale netwerk.                                                             (3)

      4.6.2    Verduidelik die voordeel daarvan om ŉ driefase-alternator in ster te
               koppel.                                                                        (2)

4.7   Verduidelik hoe koperverliese in oorhoofse transmissie verminder word.                  (2)

4.8   ŉ 380 V driefasestelsel voorsien ŉ ster-gekoppelde induktiewe las. Die
      insetdrywing na die las is 10,53 kW met ŉ nalopende drywingsfaktor van 0,8.

      Gegee:

      V = 380 V
      P = 10,53 kW
      Cos θ = 0,8 nalopend

      Bereken die:

      4.8.1    Fasespanning                                                                   (3)

      4.8.2    Lynstroom na die las                                                           (3)

      4.8.3    Fasehoek                                                                       (3)

                                                                               Blaai om asseblief

### Page 18

ELECTRICAL TECHNOLOGY:                           10
                                      POWER SYSTEMS                   GR12 0625

4.9    Refer to FIGURE 4.9 below and answer the questions that follow.

                    FIGURE 4.9: THREE-PHASE STAR CONNECTION

       4.9.1    Name TWO quantities, other than power, that can be determined by
                using the two-wattmeter method.                                              (2)

       4.9.2    Calculate the total power of the load.                                       (3)

       4.9.3    Explain why the two-wattmeter method is preferred over the
                three-wattmeter method.                                                      (2)

4.10   Draw a phasor diagram of the system, showing the correct phase sequence of
       line voltages and the angle between them.                                             (5)
                                                                                            [40]

QUESTION 5: THREE-PHASE TRANSFORMERS

5.1    Single phase transformers can be used to create a three-phase transformer
       unit. Answer the questions that follow.

       5.1.1    List THREE characteristics of single-phase transformers that must
                be identical.                                                               (3)

       5.1.2    Name the connection to the secondary side of a three-phase-
                transformer that will create a neutral point.                               (1)

5.2    Name THREE cooling methods for oil-immersed transformers.                            (3)

5.3    Name TWO factors that can contribute to excessive heating in transformers.           (2)

                                                                              Please turn over

### Page 19

ELEKTRIESE TEGNOLOGIE:                            10
                                     KRAGSTELSELS                     GR12 0625

4.9    Verwys na FIGUUR 4.9 hieronder en beantwoord die vrae wat volg.

                       FIGUUR 4.9: DRIEFASE-STERVERBINDING

       4.9.1    Noem TWEE hoeveelhede, behalwe drywing, wat bepaal kan word
                deur die tweewattmeter-metode te gebruik.                                    (2)

       4.9.2    Bereken die totale drywing van die las.                                      (3)

       4.9.3    Verduidelik waarom die tweewattmeter-metode verkies word bo die
                driewattmeter metode.                                                        (2)

4.10   Teken ŉ fasordiagram van die stelsel wat die korrekte fasevolgorde van
       lynspannings en die hoek tussen hulle aandui.                                         (5)
                                                                                            [40]

VRAAG 5: DRIEFASE-TRANSFORMATORS

5.1    Enkelfase-transformators kan gebruik word om ŉ driefase-
       transformatoreenheid te skep. Beantwoord die vrae wat volg.

       5.1.1    Noem DRIE kenmerke van enkelfase-transformators wat identies
                moet wees.                                                                  (3)

       5.1.2    Noem die verbinding met die sekondêre kant van ŉ driefase-
                transformator wat ŉ neutrale punt sal skep.                                 (1)

5.2    Noem DRIE verkoelingsmetodes vir oliegevulde-tipe transformators.                    (3)

5.3    Noem TWEE faktore wat tot oormatige verhitting in transformators kan bydra.          (2)

                                                                             Blaai om asseblief

### Page 20

ELECTRICAL TECHNOLOGY:                              11
                                       POWER SYSTEMS                     GR12 0625

5.4   Explain why transformers have better efficiency compared to other machines.               (3)

5.5   A three-phase transformer with a turns ratio of 30 : 1 is connected in delta-
      star. Answer the questions that follow.

      5.5.1     Determine whether the transformer is a step-down or step-up
                transformer.                                                                    (1)

      5.5.2     Describe why the transformer can be used for distributing electrical
                power to domestic and industrial loads.                                         (3)

5.6   Explain the principle of mutual induction with reference to transformers.                 (3)

5.7   A 100 kVA three-phase delta-star transformer with a transformer ratio of 42 : 1
      delivers power to an industrial load. The primary line voltage is 10 kV, and the
      load operates at a power factor of 0,9. Answer the questions that follow:

      Given:

      S = 100 kVA
      TR = 42 ∶ 1
      VL = 10 kV
      pf = 0,9

      Calculate the:

      5.7.1     Primary line current                                                            (3)

      5.7.2     Secondary phase voltage                                                         (3)

                                                                                  Please turn over

### Page 21

ELEKTRIESE TEGNOLOGIE:                              11
                                     KRAGSTELSELS                       GR12 0625

5.4   Verduidelik waarom transformators beter rendement het in vergelyking met
      ander masjiene.                                                                         (3)

5.5   ŉ Driefase-transformator met ŉ draaiverhouding van 30 : 1 is in delta-ster
      gekoppel. Beantwoord die vrae wat volg.

      5.5.1     Bepaal of die transformator ŉ verlagings of ŉ
                verhogingstransformator is.                                                   (1)

      5.5.2     Beskryf waarom die transformator gebruik kan word vir die
                verspreiding van elektriese krag na huishoudelike en industriële
                laste.                                                                        (3)

5.6   Verduidelik die beginsel van wedersydse induksie met verwysing na
      transformators.                                                                         (3)

5.7   ŉ 100 kVA driefase delta-ster-transformator met ŉ transformatorverhouding
      van 42: 1 lewer drywing aan ŉ industriële las. Die primêre lynspanning is
      10 kV en die las werk teen ŉ drywingsfaktor van 0,9. Beantwoord die vrae wat
      volg:

      Gegee:

      S = 100 kVA
      TR = 42 ∶ 1
      VL = 10 kV
      df = 0,9

      Bereken die:

      5.7.1     Primêre lynstroom                                                             (3)

      5.7.2     Sekondêre fasespanning                                                        (3)

                                                                               Blaai om asseblief

### Page 22

ELECTRICAL TECHNOLOGY:                              12
                                      POWER SYSTEMS                      GR12 0625

5.8   FIGURE 5.8 below shows a three-phase transformer. Answer the questions
      that follow.

                       FIGURE 5.8: THREE-PHASE TRANSFORMER

      Given:

      V = 25 kV
      V = 8,66 kV
      I = 40 A
      P = 450 kW

      Calculate the:

      5.8.1     Secondary phase voltage                                                        (3)

      5.8.2     Transformer ratio                                                              (3)

      5.8.3     Apparent power                                                                 (3)

      5.8.4     Efficiency if the copper losses are 1 kW and the core losses are 500 W         (3)

      5.8.5     Power factor                                                                (3)
                                                                                           [40]

QUESTION 6: THREE-PHASE MOTORS AND STARTERS

6.1   Name THREE mechanical inspections that could be carried out on the rotor and
      bearings of a motor.                                                                     (3)

6.2   Name TWO applications of squirrel-cage induction motors where constant
      speed and torque is essential.                                                           (2)

6.3   Describe why it is necessary to have protective devices as part of motor control.        (2)

                                                                                Please turn over

### Page 23

ELEKTRIESE TEGNOLOGIE:                             12
                                    KRAGSTELSELS                       GR12 0625

5.8   FIGUUR 5.8 hieronder toon ŉ driefase-transformator. Beantwoord die vrae wat
      volg.

                                                          IL2 = 40 A

                     FIGUUR 5.8: DRIEFASE-TRANSFORMATOR

      Gegee:

      V = 25 kV
      V = 8,66 kV
      I = 40 A
      P = 450 kW

      Bereken die:

      5.8.1     Sekondêre fasespanning                                                      (3)

      5.8.2     Transformatorverhouding                                                     (3)

      5.8.3     Skyndrywing                                                                 (3)

      5.8.4     Rendement as die koperverliese 1 kW is en die kernverliese 500 W is         (3)

      5.8.5     Drywingsfaktor                                                            (3)
                                                                                         [40]

VRAAG 6: DRIEFASEMOTORS EN -AANSITTERS

6.1   Noem DRIE meganiese inspeksies wat op die rotor en laers van ŉ motor
      uitgevoer kan word.                                                                   (3)

6.2   Noem TWEE toepassings van kourotor-induksiemotors waar konstante spoed
      en wringkraglewering noodsaaklik is.                                                  (2)

6.3   Beskryf waarom dit nodig is om beskermende toestelle as deel van
      motorbeheer te hê.                                                                    (2)

                                                                             Blaai om asseblief

### Page 24

ELECTRICAL TECHNOLOGY:                            13
                                     POWER SYSTEMS                       GR12 0625

6.4   Define the following terms with reference to three-phase motors.

      6.4.1    Synchronous speed.                                                           (2)

      6.4.2    Rotor speed.                                                                 (2)

6.5   FIGURE 6.5 below shows the rotor of an induction motor. Answer the questions
      that follow.

                     End bell

                                                           Rotor          Bearing

        Wing cover

                     A                Stator

                                                    B
                                                                          End bell

                           FIGURE 6.5: INDUCTION MOTOR

      6.5.1   Name parts A and B.                                                           (2)

      6.5.2   Identify where heat losses would be found in the motor.                       (1)

      6.5.3   Provide ONE reason why the rotor bars are skewed.                             (1)

6.6   TABLE 6.6 below shows the nameplate of a three-phase induction motor.
      Answer the questions that follow.

                    MOTOR MANUFACTURER SPECIFICATION
                    Phase                           3
                   Voltage                        380 V
                   Current                        52 A
                    Speed                      1 500 r/min
                    Power                        30 kW
                  Frequency                       50 Hz
                    Cos θ                          0,82
                  Frame nr.                       286T
         TABLE 6.6: NAMEPLATE OF A THREE-PHASE INDUCTION MOTOR

                                                                              Please turn over

### Page 25

ELEKTRIESE TEGNOLOGIE:                                13
                                     KRAGSTELSELS                        GR12 0625

6.4   Definieer die volgende terme met verwysing na driefasemotors:

      6.4.1    Sinchrone spoed                                                                  (2)

      6.4.2    Rotorspoed                                                                       (2)

6.5   FIGUUR 6.5 hieronder toon die samestelling van ŉ induksiemotor. Beantwoord
      die vrae wat volg.

                      Entplaat

                                                            Rotor         Laer

        Aansluitkas

                      A               Stator

                                                     B
                                                                          Entplaat

                             FIGUUR 6.5: INDUKSIEMOTOR

      6.5.1   Benoem onderdele A en B.                                                          (2)

      6.5.2   Identifiseer waar hitteverliese in die motor gevind sal word.                     (1)

      6.5.3   Verskaf EEN rede waarom die rotorstawe skuins is.                                 (1)

6.6   TABEL 6.6 hieronder toon die naamplaatjie van ŉ driefase-induksiemotor.
      Beantwoord die vrae wat volg.

                     MOTORVERVAARDIGER SPESIFIKASIES
                       Fase                        3
                     Spanning                    380 V
                      Stroom                      52 A
                      Spoed                   1 500 o/min
                       Krag                      30 kW
                   Frekwensie                    50 Hz
                      Cos θ                       0,82
                     Raam nr.                    286T
          TABEL 6.6: NAAMPLAATJIE VAN ŉ DRIEFASE-INDUKSIEMOTOR

                                                                                 Blaai om asseblief

### Page 26

ELECTRICAL TECHNOLOGY:                          14
                                         POWER SYSTEMS                   GR12 0625

       6.6.1     Is the motor suitable for use in South Africa? Give a reason for your
                 answer.                                                                      (2)

       6.6.2     State what the 30 kW on the nameplate indicates.                             (1)

6.7    Describe the function of a star-delta starter.                                         (2)

6.8    Explain the function of the zero-volt coil in a contactor.                             (2)

6.9    The rotor speed of an induction motor is 1 400 rpm. The synchronous speed is
       1 500 rpm and the motor has 2 pole pairs.

       Given:

       N = 1 500 rpm
       N = 1 400 rpm
       p=2

       Calculate the:

       6.9.1     Frequency of the motor                                                       (3)

       6.9.2     Percentage slip of the motor                                                 (3)

6.10   A delta connected three-phase motor with an input power of 12 kW draws
       20,99 A when connected to the supply. The motor has a power factor of 0,8 and
       an efficiency of 90%.

       Given:

       P = 12 kW
       I = 20,99 A
       Cos ø = 0,8
       n = 90%

       Calculate the:

       6.10.1    Line voltage of the motor                                                    (3)

       6.10.2    Output power of the motor                                                    (3)

       6.10.3    Reactive power at the phase angle of 36,87°                                  (3)

                                                                               Please turn over

### Page 27

ELEKTRIESE TEGNOLOGIE:                             14
                                        KRAGSTELSELS                      GR12 0625

       6.6.1    Is die motor geskik vir gebruik in Suid-Afrika? Gee ŉ rede vir jou
                antwoord.                                                                       (2)

       6.6.2    Noem wat die 30 kW op die naamplaatjie aandui.                                  (1)

6.7    Beskryf die funksie van ŉ ster-delta-aansitter.                                          (2)

6.8    Verduidelik die funksie van ŉ nul-voltspoel in ŉ kontaktor.                              (2)

6.9    Die rotorspoed van ŉ induksiemotor is 1 400 opm. Die sinchrone spoed is
       1 500 opm en die motor het 2 poolpare.

       Gegee:

       N = 1 500 opm
       N = 1 400 opm
       p=2

       Bereken die:

       6.9.1    Frekwensie van die motor                                                        (3)

       6.9.2    Persentasie glip van die motor                                                  (3)

6.10   ŉ Delta-gekoppelde driefasemotor met ŉ insetdrywing van 12 kW en trek
       20,99 A wanneer dit aan die toevoer gekoppel is. Die motor het ŉ drywingsfaktor
       van 0,8 en ŉ rendement van 90%.

       Gegee:

       P = 12 kW
       I = 20,99 A
       Cos ø = 0,8
       n = 90%

       Bereken die:

       6.10.1   Lynspanning van die motor                                                       (3)

       6.10.2   Uitsetdrywing van die motor                                                     (3)

       6.10.3   Reaktiewe drywing by die fasehoek van 36,87°                                    (3)

                                                                                 Blaai om asseblief

### Page 28

ELECTRICAL TECHNOLOGY:                          15
                                          POWER SYSTEMS                     GR12 0625

6.11   The circuit in FIGURE 6.11 below is used to control TWO three-phase motors.
       Answer the questions that follow.
       ,

                L1

            Stop                       MC1
            button                     N/O2

                 O/L1                                     O/L2
                 N/C                                      N/C

                                                                             B
                                                             T
                 A
                                                            N/O

                 MC1                      T                C

                     N
       FIGURE 6.11: AUTOMATIC SEQUENCE STARTER CONTROL CIRCUIT

       6.11.1    Label the symbols marked A, B and C.                                          (3)

       6.11.2    Identify the error in the circuit.                                            (1)

       6.11.3    Describe how this error affects the operation of the circuit.                 (4)

       6.11.4    Explain the purpose of the timer contact in the circuit.                      (2)

       6.11.5    Determine the setting of the overload in the circuit if the motor
                 nameplate has a rated current of 6 A.                                      (3)
                                                                                           [50]

                                                                                 TOTAL:    200

                                                                                           END

### Page 29

ELEKTRIESE TEGNOLOGIE:                         15
                                          KRAGSTELSELS                    GR12 0625

6.11   Die kring in FIGUUR 6.11 hieronder word gebruik om TWEE driefasemotors te
       beheer. Beantwoord die vrae wat volg.

                L1

            Stop-                     HK1
            knoppie                   N/O2

                 O/B1                                   O/B2
                 N/T                                    N/T

                                                                           B
                                                            T
                 A
                                                           N/O

                 HK1                      T              C

                     N
       FIGUUR 6.11: OUTOMATIESE SEKWENSIËLE AANSITTERBEHEERKRING

       6.11.1    Benoem die simbole gemerk A, B en C.                                         (3)

       6.11.2    Identifiseer die fout in die kring.                                          (1)

       6.11.3    Beskryf hoe hierdie fout die werking van die kring beïnvloed.                (4)

       6.11.4    Verduidelik die doel van die tydreëlaarkontakte in die stroombaan.           (2)

       6.11.5    Bepaal die instelling van die oorlading in die stroombaan as die
                 motornaamplaat ŉ nominale stroom van 6 A het.                              (3)
                                                                                           [50]

                                                                               TOTAAL:    200

                                                                                         EINDE

### Page 30

ELECTRICAL TECHNOLOGY:                    1
                                      POWER SYSTEMS                 GR12 0625

                                FORMULA SHEET

RLC CIRCUITS                               THREE-PHASE AC GENERATION
𝑃 = 𝑉 × 𝐼 × 𝐶𝑜𝑠Ɵ                           STAR
𝑋 = 2𝜋𝑓𝐿                                   𝑉 = √3𝑉
𝑋 =                                        𝑉      =𝐼   ×𝑍
𝑓 =            OR       𝑓 =                𝐼 =𝐼
       √
𝐵𝑊 =           OR       𝐵𝑊 = 𝑓 − 𝑓
                                           DELTA
SERIES                                     𝑉 =𝑉
𝑉 = 𝐼𝑅                                     𝑉 =𝐼 × 𝑍
𝑉 = 𝐼𝑋                                     𝐼 = √3 𝐼
  𝑉 = 𝐼𝑋
𝐼 =         OR      𝐼 =𝐼 =𝐼 =𝐼             POWER
𝑍=    𝑅 + (𝑋 − 𝑋 )                         𝑆 (𝑃    ) = √3 𝑉     𝐼

𝑉 =   𝑉    + (𝑉 − 𝑉 )     OR 𝑉 = 𝐼𝑍        𝑄 (𝑃 ) = √3 𝑉 𝐼 𝑆𝑖𝑛Ɵ

𝐶𝑜𝑠Ɵ =        OR    𝐶𝑜𝑠Ɵ =                 𝑃 = √3 𝑉 𝐼 𝐶𝑜𝑠Ɵ

𝑄=     =     =      =     =                𝐶𝑜𝑠Ɵ =

PARALLEL                                   EFFICIENCY
𝑉 =𝑉 =𝑉 =𝑉                                 𝜂=          × 100

𝐼 =
𝐼 =                                        TWO-WATTMETER METHOD
𝐼 =                                        𝑃 =𝑃 +𝑃

𝐼 =    𝐼   + (𝐼 − 𝐼 )                      tanƟ=√3(         )

𝑍=

𝐶𝑜𝑠Ɵ =                                     THREE-WATTMETER METHOD
𝑄=     =                                   𝑃 =𝑃 +𝑃 +𝑃

### Page 31

ELEKTRIESE TEGNOLOGIE:                  1
                                             KRAGSTELSELS                GR12 0625

                                        FORMULEBLAD

RLC-KRINGE                                        DRIEFASE-WS-OPWEKKING
P = V × I × CosƟ                                  STER
X = 2πfL                                          V = √3V
X =                                               V = I ×Z

f =           OF        f =                       I =I
       √

BW =          OF       BW = f − f
                                                  DELTA
SERIE                                             V =V
V = IR                                            V =I × Z
V = IX                                            I = √3 I
V = IX
I =         OF         I =I =I =I                 DRYWING

Z=     R + (X − X )                               S (P   ) = √3 V   I
                                                  Q (P ) = √3 V I SinƟ
V =    V   + (V − V )         OF    V = IZ

CosƟ =       OF        CosƟ =                     P = √3 V I CosƟ

Q=     =    =      =     =                        CosƟ =

PARALLEL                                          RENDEMENT
V =V =V =V                                        η=       × 100

I =
I =                                               TWEEWATTMETERMETODE

I =                                               P =P +P

                                                  tanƟ=√3(      )
I =    I   + (I − I )

Z=

CosƟ =                                            DRIEWATTMETERMETODE

Q=     =                                          P =P +P +P

### Page 32

ELECTRICAL TECHNOLOGY:                       2
                       POWER SYSTEMS                    GR12 0625

                               THREE-PHASE MOTORS AND
 THREE-PHASE TRANSFORMERS
                                      STARTERS
STAR                        STAR
𝑉 = √3𝑉                     𝑉 = √3𝑉
𝐼 =𝐼                        𝐼 =𝐼

DELTA                       DELTA
𝑉 =𝑉                        𝑉 =𝑉
𝐼 = √3𝐼                     𝐼 = √3𝐼

POWER                       POWER
𝑆 (𝑃    ) = √3 𝑉   𝐼        𝑆 (𝑃    ) = √3 𝑉     𝐼

𝑄 (𝑃 ) = √3 𝑉 𝐼 𝑆𝑖𝑛Ɵ        𝑄 (𝑃 ) = √3 𝑉 𝐼 𝑆𝑖𝑛Ɵ

𝑃 = √3 𝑉 𝐼 𝐶𝑜𝑠Ɵ             𝑃 = √3 𝑉 𝐼 𝐶𝑜𝑠Ɵ
                            𝑃 = √3 𝑉 𝐼 𝐶𝑜𝑠Ɵ 𝜂
𝐶𝑜𝑠Ɵ =                      𝐶𝑜𝑠Ɵ =
  ( )           ( )
        =   =
  ( )           ( )

𝑇𝑅 =                        EFFICIENCY

                            𝜂=             × 100

                            𝜂=                  × 100

                            𝜂=          × 100

                            SPEED
                            𝑝=
                                    х
                            𝑛 =

                            𝑃𝑒𝑟 𝑈𝑛𝑖𝑡 𝑆𝑙𝑖𝑝 =

                            % 𝑆𝑙𝑖𝑝 =        х 100

                            𝑛 = 𝑛 (1 − %𝑠𝑙𝑖𝑝)
                            𝑆𝑙𝑖𝑝 = 𝑛 − 𝑛

### Page 33

ELEKTRIESE TEGNOLOGIE:                      2
                         KRAGSTELSELS                    GR12 0625

DRIEFASETRANSFORMATORS     DRIEFASEMOTORS EN -AANSITTERS
STER                       STER
V = √3V                    V = √3V
I =I                       I =I

DELTA                      DELTA
V =V                       V =V
I = √3I                    I = √3I

DRYWING                    DRYWING
S (P ) = √3 V I            S (P ) = √3 V I
Q (P ) = √3 V I SinƟ       Q (P ) = √3 V I SinƟ
P = √3 V I CosƟ            P = √3 V I CosƟ
                           P = √3 V I CosƟ η
CosƟ =                     CosƟ =
 ( )           ( )
       =   =
 ( )           ( )

TR =                       RENDEMENT

                           η=                   × 100

                           η=                    × 100

                           η=           × 100

                           SPOED
                           p=
                                    х
                           n =
                           Per Eenheid Glip =
                           % Glip =             х 100
                           n = n (1 − %glip)

                           Glip = n − n

## Related documents

- [Electrical Technology P1 (Electronics) (English) June 2025 Possible Answers](https://www.hlayiso.com/library/electrical-technology-p1-electronics-english-june-2025-possible-answers/4302563e-89b7-4f54-8a21-63b2020e985f) — Electrical Technology · Memo · 2025 · Eng
- [ELEC TECH QP SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-qp-sept2023-electronics-english/867c1cd7-df12-484d-93b7-8812de59d0db) — Electrical Technology · QP · 2023 · Eng
- [ELEC TECH GR12 QP SEPT2022 Power English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2022-power-english/5dde0506-b8db-4a28-a65d-02c30160901e) — Electrical Technology · QP · 2022 · Eng
- [ELEC TECH GR12 QP SEPT2022 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-qp-sept2022-digital-english/924ce4d5-b0c3-4149-a3f9-e96ddcf13df1) — Electrical Technology · QP · 2022 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Power Systems English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-power-systems-english/bea78337-b137-406a-9b4a-c6e631a84c9d) — Electrical Technology · Memo · 2024 · Eng
- [ELEC TECH GR12 MEMO SEPT2024 Electronics English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-electronics-english/c80784c8-a9c8-49f8-b740-a29558fe2de9) — Electrical Technology · Memo · 2024 · Eng

## More from Grade 12 Electrical Technology

- [Gr 12 Dig Elec ATP 2023-24](https://www.hlayiso.com/library/gr-12-dig-elec-atp-2023-24/8d3b2ee7-1d14-498d-a86b-d9fc34674531) — ATP
- [ELECTRIC TECH (Digital) MEMO GR12 SEPT 2025 ENG watermark](https://www.hlayiso.com/library/electric-tech-digital-memo-gr12-sept-2025-eng-watermark/0a867070-2654-43cf-8e48-5037555e0c3d) — Memo · 2025 · Eng
- [Electrical Technology Nov 2025 (Digital) MG Afr](https://www.hlayiso.com/library/grade-12-electrical-technology-2025-nsc-november-exam-memorandum/3b862a0c-6a87-4296-b5b6-09b072c7d1e9) — Memo · 2025 · Afr
- [ELEC TECH GR12 MEMO SEPT2024 Digital English](https://www.hlayiso.com/library/elec-tech-gr12-memo-sept2024-digital-english/cb603860-b00d-40c2-a36b-aa5e97b7d1e5) — Memo · 2024 · Eng
- [ELEC TECH MEMO SEPT2023 Digital English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-digital-english/1d2b04e7-c486-4f4e-9494-b0ccbcaf2ebb) — Memo · 2023 · Eng
- [ELEC TECH MEMO SEPT2023 Electronics English](https://www.hlayiso.com/library/elec-tech-memo-sept2023-electronics-english/5630ca3e-e352-4f96-81d0-64ec0103c0e9) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
