# Engineering Graphics and Design Grade 12 P2 NSC June 2024 QP

> Grade 12 Engineering Graphics and Design Paper 2 question paper from the NSC June Exam 2024 (Afrikaans), 12 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/gr-12-edg-p2-english-and-afrikaans-june-2024-question-paper/267ef720-fc62-43ed-9f51-a80776ead7ce
- Updated: 2026-09-27
- Subject: Engineering Graphics and Design
- Grade: Grade 12
- Language: Afrikaans
- Document type: Question paper
- Year: 2024
- Exam period: NSC June Exam
- Paper: 2
- Curriculum: CAPS
- Pages: 12

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Engineering Graphics and Design](https://www.hlayiso.com/library/grade-12/engineering-graphic-and-design) › [Engineering Graphics and Design Grade 12 P2 NSC June 2024 QP](https://www.hlayiso.com/library/gr-12-edg-p2-english-and-afrikaans-june-2024-question-paper/267ef720-fc62-43ed-9f51-a80776ead7ce)

## About this document

Engineering Graphic And Design · Grade 12 · NSC June Exam · 2024 · Afrikaans. Question paper, 12 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

basic education

Department:
Basic Education
REPUBLIC OF SOUTH AFRICA

SENIOR CERTIFICATE EXAMINATIONS/
NATIONAL SENIOR CERTIFICATE EXAMINATIONS

ENGINEERING GRAPHICS AND DESIGN P2

MAY/JUNE 2024

MARKS: 100

TIME: 3 hours

ENGINEERING GRAPHICS & DESIGN P2

A 00 |

This question paper consists of 6 pages. gO77zE

Barcode label X05

i

INSTRUCTIONS AND INFORMATION

41.
2
3.
4.
5.
6.
i
8.
9.

10.

This question paper consists of FOUR questions.

. Answer ALL the questions.

ALL drawings are in third-angle orthographic projection, unless otherwise stated.

. ALL drawings must be prepared using pencil and instruments, unless otherwise

stated.
ALL answers must be drawn accurately and neatly.

. ALL the questions must be answered on the QUESTION PAPER, as instructed.
. ALL the pages, irrespective of whether the question was attempted or not, must

be re-stapled in numerical sequence in the TOP LEFT-HAND CORNER ONLY.

. Time management is essential in order to complete all the questions.

Print your examination number in the block provided on every page.
Any details or dimensions not given must be assumed in good proportion.

FOR OFFICIAL USE ONLY
QUESTION | MARKS OBTAINED 3 ‘SIGN MODERATED i SIGN RE-MARKING 4} Sicn
1
2
3
4
TOTAL
2/;0/0 2/0/0 2/0)/0
[FINAL ‘CONVERTED MARK CHECKED BY ———T

COMPLETE THE FOLLOWING:
CENTRE NUMBER

CENTRE NUMBER
EXAMINATION NUMBER

EXAMINATION NUMBER

DO NOT FOLD THE QUESTION PAPER IN HALF.

Please tum over

Copyright reserved me

### Page 2

Downloaded from hlayiso.com

Engineering Graphics and Design/P2

SCINSC Confidential

DBE May/June 2024

cee

4x 816 HOLE CBORE
32x 2DEEP

g

q

a

427,
A,

24.

;

12,

78

4xM14x4,5

AUXILIARY VIEW

R18 )

QUESTION 1: ANALYTICAL (MECHANICAL)

Given:
The front view, top view, right view and an auxiliary view of a corner bracket, a title block and a table of questions.
The drawing is not presented to the indicated scale.

Instructions:
Complete the table below by neatly answering the questions, which refer to the accompanying drawings, title block
and mechanical content. [30]

QUESTIONS ANSWERS

Who approved the drawing?

What is the web address of the draughting firm?

What is the file name of the drawing?

How many corner brackets must be manufactured?

How deep is the counter bore of the 4 x 216 holes?

if a scale of 1: 1 was used, how would the dimension at A
read?

Which VIEW is the front view of the drawing?

1
2
3
4
5 | What drawing method has been used to prepare the drawing?
6
7
8
9

How many threaded holes are on the bracket?

Name the feature at B.

Determine the complete dimensions at: C: D: E:

Measure the angle at H.

n
fo}
wlajala}a)a

Determine the complete dimension at J.

With reference to the tolerance, determine the maximum and 2
minimum dimensions for K.

190.

VIEW 3.

15. | How many surfaces on the corner bracket must be machined? 1

Match the surfaces labelled Q and R on VIEW 3 with the y 2
corresponding labelled surfaces on VIEW 2. R

16

17 | Which view shows the true shape of the surface at W? 4

What is indicated by C on the machining symbol at 4 in the title fi

18 2

49 | What does the machining symbol at 2 in the title panel indicate? 1

In the space below (ANSWER 20), complete, in neat freehand, the side view of each of the three 4
SANS 1011 conventions of the interrupted views shown.

TOTAL | 30

HANGER STREET
CAPE TOWN

COMMISSIONED BY:
BRACKETS FOR AFRICA

DRAWING
PROGRAMME:

AUTOCAD 2023

1
ALL DIMENSIONS ARE IN MILLIMETRES. MILLING

QUANTITY: 1500

FILE NAME: JJVWBJ-6

DRAWING No. 013

SCALE 1:3

DRAWN BY: VERNON —_| DATE: 2023-05-19

63 HUBBLE ROAD
CAPE TOWN
7700

MECHANICAL DRAUGHTERS.

www .meodraw.co.za
021 291 0910

CHECKED BY: BARRY —_| DATE: 2023-08-27 2

APPROVED: SIPHO DATE: 2023-05-31

THLE:

CORNER BRACKET

‘ALL UNSPECIFIED RADII
ARE 2.5mm.

1: 1002
TOLERANCE : 100

ANSWER 20

at 3-H B

VA

EXAMINATION NUMBER

EXAMINATION NUMBER [2

Copyright reserved

Please tum over

### Page 3

Downloaded from hlayiso.com

Engineering Graphics and Design/P2

SCINSC Confidentiat

DBE MayhJune 2024

ge

0°

QUESTION 2: LOCI (CAM)

Given:

« The detail of a camshaft and a wedge-shaped
fotlower at the minimum distance from the camshaft
centre

* The position of centre point P on the drawing sheet

Specifications:

« The wedge-shaped follower reciprocates along a
60° line that passes through the centre of the
camshaft.

¢ The minimum distance from the follower to the
centre of the camshaft = 20mm

* Rotation = anti-clockwise

Motion:

The cam imparts the following motion to the wedge-

shaped follower:

It rises 40 mm over the first 60° with uniform motion.

There is a dwell period for the next 30°.

It rises to its maximum displacement of 80 mm over
the next 90° with uniform motion.

«lt descends 40 mm over the next 90° with simple
harmonic motion.

It returns to its original position with uniform
acceleration and retardation over the remainder of
the rotation.

Instructions:

Using centre point P on the drawing sheet, draw, to
scale 1: 1, the camshaft and wedge-shaped
follower in the given position.

¢ Draw to a rotational scale of 30° = 8 mm anda
displacement scale of 1 : 1, the complete
displacement graph for the required motion.

* Using the given position of the follower as 0°, project
and draw the cam profile from the displacement
graph.

‘Indicate the direction of rotation on the cam profile
with an arrow.

¢ Indicate the rotational scale of the graph.

Show ALL construction and projection. [37]

ASSESSMENT CRITERIA

GIVEN + MINIMUM
DISTANCE + CL

1

2. |GRAPH CONSTRUCTION
(3 [PLOTTING GRAPH +
4

GRAPH CURVES
CAM CONSTRUCTION

alolala

5 |PLOTTING +CAMPROFILE | 11 ae
PENALTIES (-)

WEDGE-SHAPED FOLLOWER
AND CAMSHAFT DETAIL

TOTAL) 37
EXAMINATION NUMBER:

EXAMINATION NUMBER [3

Copynght reserved

Please tum over

### Page 4

Downloaded from hlayiso.com

Enginoering Grephies and Design/P2 SCINSC Confidential DBE May/June 2024

f? QUESTION 3: ISOMETRIC DRAWING
oe
ia Given:
» The front view, top view and right view of a
casting
© The position of point A on the drawing sheet

Instructions:

:1, convert the orthographic views.
into an isometric drawing.

Use A as the starting and lowest point of the
drawing.

© Show ALL construction.

+ NO hidden detail is required. [40]

18,

i
1
139

| [L FR rt ae |

412

al ‘ASSESSMENT CRITERIA
PLACING + AUX. VIEW 2

FRONT PORTION 124

ely

UPPER PORTION 184
4 |ARCS + CONSTR. + CL 7
PENALTIES (-)

TOTAL] 40
EXAMINATION NUMBER

EXAMINATION NUMBER =» [4
Please tum over

Copyright reserved

### Page 5

Downloaded from hlayiso.com

Engineering Graphics and Desigr/P2 SC/NSC Confidential DBE May/June 2024

«0 3, 228 > 8 QUESTION 4; MECHANICAL ASSEMBLY
28. 4 =n
C = [2 me ‘@) ° Given:
{-—-— 4+ € ae 0 © Orthographic views of each part of the fixed lathe steady
- assembly
PIN [3] in oro 28 * The exploded isometric drawing of the parts of a fixed
ry lathe steady assembly, showing the position of each part
LOCK SCREW [4] 7—pH— at 1 relative to all the others
* | 4 o
40 on a T Instructions:
* Answer this question on page 6.
i 8 | 7 RING [9] Draw, to scale 1: 1 and in third-angle orthographic
e 3 SCREW CAP {8} projection, the following views of the assembled parts of
ol H the fixed lathe steady assembly:
"I mio 4.1. The front view as seen from the direction of the
Reo |! |_me L4 mio arrow on the exploded isometric drawing.
Ras 4.2. A sectional left vi tting pl NA. Th
AD. TIN hs sectional left view on cul plane . 16
R35 PUNE ht cutting plane is shown on the front view of the

base (part 1).

« The drawing must comply with the SANS 10117
guidelines.

* Draw the guide (part 6), adjusting screw (part 7), screw
cap (part 8) and the ring (part 9) only in the top hole
marked B.

49

7
ES
Lf
t

By

3
45
4a

_ B [|
220 Pay “1 ‘ :
Ch [ NEA oO P Btenning is oxsentl
ass_7

g| « The convention of symmetry may NOT be applied.
tn
v 3]
CLAMP [2] 4

* Draw only the top lock screw (part 4) in position, as shown

Gil GUIDE [6] in the exploded isometric drawing.
36 MIDEOET Es] * Show THREE faces of the M10 bolt (part 5) in the front
al i fir tH] SN NO hidden detail is required.
a vn H i a) 7 Add cutting plane A-A. (93)
g i | thi) — |
H \ V
' I .
1 i
I
Pe ' PARTS LIST
I PARTS (QUANTITY MATERIAL
1 | BASE 1 CAST IRON
2 | CLAMP 1 CAST IRON
aI 3 | PIN 1 ‘STEEL
“ 4 | LOCK SCREW 1 STEEL
5 | M10B0LT 1 STEEL
6 | GUIDE t BRASS,
ADJUSTING
g| 7 | screw 1 STEEL
panne. 7 8 | SCREW CAP 1 BRASS
9 | RING 1 ALUMINIUM
7 XANDER STREET
GUIDANCE DE JAGER
ENGINEERING CC ‘www.guidance.co.za
‘@ 012 345 6789
FIXED STEADY ASSEMBLY
BASE [1] ALL DIMENSIONS ARE IN MILLIMETRES. © &4
[5]
Copyright reserved Please tum over

### Page 6

Downloaded from hlayiso.com

Engineering Grephics and Desig/P2 SC/NSC Confidential DBE May/June 2024
FOR OFFICIAL USE ONLY
INCORRECT ORTHOGRAPHIC PROJECTION:
INCORRECT OVERALL SCALE
INCORRECT HATCHING
PARTS NOT ASSEMBLED
TOTAL PENALTIES (-)
ASSESSMENT CRITERIA
FRONT VIEW
reese | omnes | non | uccere
1 | ease 15,
2 | camps 6
a lero |
4 | ouwe 1
5 |rocxscrew | 24
6 | mioeo.t 6
7 | Saw 1
SUBTOTAL | 334
SECTIONAL LEFT VIEW
1 | BASE 12
2 | cum 7
3. | euwe 8}
a
5 | Rine 3
6 |tockscrew | 49
7 | sorewcar 3
SUBTOTAL | 444
GENERAL
1 | CENTRE LINES 4
2 | ASSEMBLY 8
3 | oun. 3
SUBTOTAL 15
TOTAL| 93
PENALTIES (-)
GRAND TOTAL
EXAMINATION NUMBER
ei ted EXAMINATION NUMBER [6

Copyright reserved

### Page 7

ys

Downloaded from hlayiso.com

Vertroulik

basic education

Department:
Basic Education
REPUBLIC OF SOUTH AFRICA

wT

SENIORSERTIFIKAAT-EKSAMEN/
NASIONALE SENIORSERTIFIKAAT-EKSAMEN

INGENIEURSGRAFIKA EN -ONTWERP V2

MEI/JUNIE 2024

Kopiereg voorbehou

PUNTE: 100

TYD: 3uur

ING GRAFIKA & ONTWERP V2

10772A
Hierdie vraestel bestaan uit 6 bladsye.

Hee 7

| |

I |

| X05
l Stafieskode-plakker

| |

| |

Lo LL |

INSTRUKSIES EN INLIGTING

Hierdie vraestel bestaan uit VIER vrae.

Beantwoord AL die vrae.

ALLE tekene is in derdehoekse ortografiese projeksie, tensy anders aangedui.
ALLE tekene moet met potiood en instrumente voorberei word, tensy anders
aangedui.

ALLE antwoorde moet akkuraat en netjies geteken word.

AL die vrae moet, soos voorgeskryf, op die VRAESTEL beantwoord word.

AL die bladsye moet weer in nommervolgorde in SLEGS die BOONSTE
LINKERKANTSTE HOEK vasgekram word, ongeag of die vraag beantwoord is, of
nie.

8. Tydsbestuur is noodsaaklik om al die vrae te voltooi.

9. Drukskryf jou eksamennommer in die blokkie op elke bladsy voorsien.

40.Enige besonderhede of afmetings wat nie gegee is nie, moet in goeie verhouding
veronderstel word.

Se edd

SLEGS VIR AMPTELIKE GEBRUIK

VRAAG. PUNTBEHAAL | }| TEKEN| GEMODEREER | 4] TEKEN| HERNASIEN | 3 | TEKEN

TOTAAL

2/0/0 2|0/0 2/;0/0

NAGESIEN DEUR

FINALE VERWERKTE PUNT

100

VOLTOOIDIE VOLGENDE: |
SENTRUMNOMMER

SENTRUMNOMMER
EKSAMENNOMMER

EKSAMENNOMMER

MOENIE DIE VRAESTEL IN DIE HELFTE VOU NIE.

Bieai om asseblief

### Page 8

Downloaded from hlayiso.com

Ingenioursgrafika en -ontwerp/V2

SSANSS Vertroulik

DBE MeitJunie 2024

4x 216 GAT PVS,
32 x2 DIEP

@

VRAAG 1: ANALITIES (MEGANIES)

Gegee:
Die vooraansig, boaansig, regteraansig en 'n hulpaansig van ‘n hoeksteun, 'n titelblok en ‘n tabel met vrae.
Die tekening is nie volgens die aangeduide skaal voorgestel nie.

Instruksles:
Voltooi die tabel hieronder deur die vrae, wat na die bygaande tekening, titelblok en meganiese inhoud verwys, netjies

= te beantwoord. [30]
4x M14 x15
| VRAE ANTWOORDE
ia? 1 | Wie het die tekening goedgekeur? 1
ran 2_ | Wat Is die webadres van die tekenfirma? 1
TH 3 | Wat is die léernaam van die tekening? 1
4 | Hoeveel hoeksteune moet vervaardig word? 1
ko 5 | Watter tekenmetode is gebruik om die tekening voor te berei? 1
6 | Hoe diep is die parallelversinking van die 4 x @16 gate? 1
7 | As'n skaal van 1: 1 gebruik is, hoe sal die afmeting by A lees? A
8 | Watter AANSIG is die vooraansig van die tekening? 1
9 | Hoeveel gate met skroefdraad is daar op die hoeksteun? 1
10 | Noem die kenmerk by B. 4
11 | Bepaal die volledige afmetings by: C: D: E: Fr G: 5
12 | Meet die hoek by H. 1
13 | Bepaal die volledige afmeting by J. 2
14 Met verwysing na die toleransie, bepaal die maksimum en 2
minimum afmetings by K.
15 | Hoeveel opperviakke op die hoeksteun moet gemasjineer word? 1
Ree | | a 46 | Pa8 die opperviakke gemerk Q en R op AANSIG 3 by die a zs
T Co i 1 iJ =) ooreenkomstige gemerkte opperviakke op AANSIG 2, R:
T 17 | Watter aansig toon die ware vorm van die viak by W? 1
@ HH © 4a | Wat word deur C op dle masjiensimbool by 1 in de ttelblok i
t aangedui?
a 1 19 Wat word deur die masjiensimbool by 2 in die titelblok 1
hal 7 70 aangedui?
A 50 30 29 |!" die spasie hieronder (ANTWOORD 20), voltool, in netjiese vryhand, die kantaansig van elkeen |
. as van die drie SANS 10111-konvensies van die onderbroke aansigte getoon.
AANSIG 1 AANSIG 3 TOTAAL | 30
iatoe vn aria TeKENpRoGRAM: | AUTOCAD 2029. | ALLE AFMETINGS IS IN MILLIMETER, 1 Freee ANTWOORD 20
KAAPSTAD. HOEVEELHEID: 1500 if A Hf -—9- Ht B I Et c 4]
LEERNAAM: JIVWBI6 TEKENING Nr.013. | SKAAL 1:3 GETEKEN DEUR: VERNON DATUM: 2029-05-19
nkeretnaat sagt oz NAGESIEN DEUR: BARRY | DATUM: 2023-0527 | 2
7700 GOEDGEKEUR: SIPHO DATUM: 2023-05-31 on EKSAMENNOMMER
THTeL: HOEKSTEUN Ser nlinee i os TOLERANSIE : {2.02 HGAROWEN ie
Kopiereg voorbehou Blaai om asseblier

### Page 9

Downloaded from hlayiso.com

Ingenioursgrafika en -ontwerp/V2 SSINSS Vertroulik DBE Mei/Junie 2024

A VRAAG 2: LOKUS (NOK)

Gegee:

* Die besonderhede van ‘n nokas en 'n wigvormige
volger by die minimum afstand vanaf die
nokassenter

* Die posisie van senterpunt P op die tekenvel

Spesifikasies:

* Die wigvormige voiger beweeg heen en weer op 'n
60°-lyn wat deur die senter van die nokas beweeg.
* Die minimum afstand vanaf die volger na die senter
van die nokas = 20 mm
 Rotasie = anti-kloksgewys

Beweging:

Die nok verleen die volgende beweging aan die

wigvormige volger:

# Dit styg 40 mm oor die eerste 60° met eenvormige
beweging.

« Daar is 'n rusperiode vir die volgende 30°.

Dit styg tot die maksimum verplasing van 80 mm
coor die volgende 90° met eenvormige beweging.

* Dit daal 40 mm oor die volgende 90° met
eenvoudige harmoniese beweging.

* Dit keer terug na die oorspronklike posisie met
eenvormige versnelling en vertraging oor die res
van die rotasie.

Instruksies:
+ © Gebruik senterpunt P op die tekenvel en teken,
P volgens skaal 1 : 1, die nokas en wigvormige volger

in die gegewe posisie.

 Teken, volgens 'n rotasieskaal van 30° = 8 mm en'n
verplasingskaal van 1 : 1, die volledige verplasings-
grafiek vir die vereiste beweging.

* Gebruik die gegewe posisie van die voiger as 0° en
projekteer en teken die nokprofiel vanaf die

verplasingsgrafiek.
« Dui die rotasierigting van die nokprofiet met ‘n pyl
aan.
© Dui die rotasieskaal van die grafiek aan.
* Toon ALLE konstruksies en projeksies. [37]
ASSESSERINGSKRITERIA
6
(GEGEE + MINIMUM
ha 1 JarSTAND + st 3
2 |GRAFIEKKONSTRUKSIE | 7
y 3. | GRAFIEKSTIPWERK + 9
-KURWES,
4 |NOKSAMESTELLING 5
= 5 |STIPWERK + NOKPROFIEL | 14

6
>; PENALISERING (-)
P 216 TOTAAL} 37

EKSAMENNOMMER

WIGVORMIGE VOLGER EN
NOKASBESONDERHEDE

EKSAMENNOMMER, 3

Kopiereg voorbehou Biaai om assebliof

### Page 10

Downloaded from hlayiso.com

Ingenieursgrafika en -ontwerp/V2 SSINSS Vertroulik DBE Mei/Junie 2024

Pp. VRAAG 3: ISOMETRIESE TEKENING

Gegee:

* Die vooraansig, boaansig en regteraansig van
‘'n gietstuk

« Die posisie van punt A op die tekenvel

Instruksies:

Gebruik skaal 1 : 1 en omskep die ortografiese

aansigte van die gietstuk in 'n isometriese

tekening.

» Gebruik A as die begin- en laagste punt van
die tekening.

* Toon ALLE konstruksies.

» GEEN verborge besonderhede word verlang
NIE. £40]

18,

a lo" 7 Lest" 5
i

| _a|12|_ 96
112,

52 22 65

ASSESSERINGSKRITERIA
PLASING + HULPAANSIG | 2

VOORSTE GEDEELTE 123

BOONSTE GEDEELTE 183

4 peop souaae 7

PENALISERING (-)

el ria

TOTAAL| 40
EKSAMENNOMMER

aye EKSAMENNOMMER on [4
Kopiereg voorbehou areane Blaai om assabiiof

### Page 11

Downloaded from hlayiso.com

Ingenioursgrafika en -ontwerpV2 SS/NSS Vertroulik

DBE MoitJunie 2024

@,

M32 x2 240 28

a 218.

E
3

QD
€
3
F
co}
iy
3

A

a]

RING [8]

|
SKROEFDOP [8]

mio

Rag

|
L TT —
rit’

M10-BOUT [5]

40

35,

120

ot
assis ned SY

Sig UITSKUIF- ISOMETRIESE TEKENING

VRAAG 4: MEGANIESE SAMESTELLING

Gegee:

Ortografiese aansigte van elke onderdeel van die vaste

draaibankorilsamestelling

¢ Die uitskuif- isometriese tekening van die onderdele van 'n
vaste draaibankbrilsamestelling, wat die posisie van elke
onderdeel relatief tot al die ander toon

Instruksies:
° Beantwoord hierdie vraag op bladsy 6.
¢ Teken, volgens skaal 1 : 1 en in derdehoekse ortografiese
projeksie, die volgende aansigte van die saamgestelde
onderdele van die vaste draaibankbrilsamestelling:
4.1. Die vooraansig soos gesien vanuit die rigting van die
pyl op die uitskuif- isometriese tekening.
4.2 'n Deursnee-linkeraansig op snyviak A-A. Die
snyvlak word op die vooraansig van die basis (onder-
deel 1) getoon.

LET WEL:

* Beplanning is noodsaaklik.

* Die konvensie van simmetrie mag NIE toegepas word NIE.

© Die tekening moet aan die SANS 10111-riglyne voldoen,

* Teken die gids (onderdeel 6), verstelskroef (onderdeel 7),
skroefdop (onderdeel 8) en die ring (onderdeel 9) slegs in
die boonste gat gemerk

* Teken slegs die boonst:

Iuitskroef (onderdeel

posisie, soos in die uitskuif- isometriese tekening getoon.
* Toon DRIE vlakke van die M10-bout (onderdeel 5) in die
vooraansig.
e GEEN verborge besonderhede word verlang NIE.
© Voeg snyvlak A-A by. [93]
LYS VAN ONDERDELE
ONDERDELE HOEVEELHEID | | MATERIAAL
1 | BASIS 1 GIETYSTER
2 |KLAMP 4 GIETYSTER
3 | PEN 1 STAAL
4. | SLUITSKROEF 1 STAAL
5 | M10-BOUT 1 STAAL
6 | cIDs 1 GEELKOPER
VERSTEL-
7 | skroer v Gi
8 | SKROEFDOP 1 GEELKOPER
9 | RING 1 ALUMINIUM
XANDERSTRAAT 7
GUIDANCE DE JAGER
INGENIEURSWERKE BK eee Bas 1oe.00 za)
012 345 6789
VASTE BRILSAMESTELLING
ALLE AFMETINGS IS IN MILLIMETER. © 4 a

Blaai om assebliof

### Page 12

Downloaded from hlayiso.com

Ingenieursgratike en -ontwerp/V2

SS/NSS Vertroulik

DBE Mei/Junie 2024

Pp. SLEGS VIR AMPTELIKE GEBRUIK
ve VERKEERDE ORTOGRAFIESE PROJEKSIE
VERKEERDE ALGEHELE SKAAL
VERKEERDE ARSERING
ONDERDELE NIE SAAMGESTEL NIE
PENALISERINGSTOTAAL (-)
ASSESSERINGSKRITERIA
VOORAANSIG
1 | Basis 15
2. | KAMP PEN 5
3 | srocroop+ams | 3
4 | cos 1
5 | sturskroer 24
6 | mi0-80uT 6
7 | VeRSTELSKROEF 1
SUBTOTAAL 334
DEURSNEE-LINKERAANSIG
1 | Basis 12
2 | Kame 7
3. | cws 34
4 | versterskroer 64
5 | Rw 3
6 | swurtskroer 43
7 _| SkROEFDOP: 3
SUBTOTAAL 444
ALGEMEEN
1_| SeNTERLYNE 4
2 | SAMESTELLING 8
3 | suakan 3
SUBTOTAAL 15
TOTAAL 93
PENALISERING (-)
GROOTTOTAAL
EKSAMENNOMMER
Sy i EKSAMENNOMMER [6

## Related documents

- [Tech Draw P1 (HG) (English and Afrikaans) Diagram Sheet](https://www.hlayiso.com/library/tech-draw-p1-hg-english-and-afrikaans-diagram-sheet/7f38f42b-0264-403c-bded-b80fbd0b6cfd) — Engineering Graphic and Design · QP · 2014 · Afr
- [Engineering Graphics Design P1 May June 2021 Afr](https://www.hlayiso.com/library/engineering-graphics-design-p1-may-june-2021-afr/f290a6a3-a7cf-44f6-9087-17a45b187609) — Engineering Graphic and Design · QP · 2021 · Afr
- [Engineering Graphics Design P1 May June 2021 Eng](https://www.hlayiso.com/library/engineering-graphics-design-p1-may-june-2021-eng/5748ef99-69a6-4e4c-900c-2b8c5f2da3a4) — Engineering Graphic and Design · QP · 2021 · Eng
- [Engineering Graphics Design P1 May June 2018 Afr](https://www.hlayiso.com/library/engineering-graphics-design-p1-may-june-2018-afr/87e40f03-4299-49a9-bc86-3d5add5613c4) — Engineering Graphic and Design · QP · 2018 · Afr
- [EGD P2 QP SEPT2023 AFR](https://www.hlayiso.com/library/egd-p2-qp-sept2023-afr/bcd511cb-4c3a-4c53-afc7-47f820a47af7) — Engineering Graphic and Design · QP · 2023 · Afr
- [Engineering Graphics & Design P2 Nov 2023 Afr](https://www.hlayiso.com/library/engineering-graphics-design-p2-nov-2023-afr/80ebd271-1cb0-42e2-88c6-6d5fbcffc986) — Engineering Graphic and Design · QP · 2023 · Afr

## More from Grade 12 Engineering Graphics and Design

- [EGD p1 Memo protected watermark](https://www.hlayiso.com/library/egd-p1-memo-protected-watermark/4afe999d-829f-4029-81f4-f01ba594587f) — Memo · 2025
- [Engineering Graphics and Design P2 June 2025 Possible Answers](https://www.hlayiso.com/library/engineering-graphics-and-design-p2-june-2025-possible-answers/33c95b30-d504-42bd-acc1-56b020ec92fb) — Memo · 2025
- [EGD P1 GR12 MEMO SEPT2023 Afr+Engl](https://www.hlayiso.com/library/egd-p1-gr12-memo-sept2023-afr-engl/f0ef5f18-cddf-486c-9131-1f3fc1806ba4) — Memo · 2023 · Afr
- [Engineering Graphics & Design P1 Nov 2023 Eng](https://www.hlayiso.com/library/engineering-graphics-design-p1-nov-2023-eng/15d72a8f-e8dc-4d1e-82bc-86650e523125) — QP · 2023 · Eng
- [Engineering Graphics & Design P2 Nov 2023 Eng](https://www.hlayiso.com/library/engineering-graphics-design-p2-nov-2023-eng/c5be1276-555b-4443-9c96-80e1e5201252) — QP · 2023 · Eng
- [EGD MEMO P1 EA](https://www.hlayiso.com/library/egd-memo-p1-ea/4d9b5038-c328-4ca1-9dfa-3a811ac596b7) — Memo · 2022

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.