# Engineering Graphics and Design Grade 11 P2 2020 QP > Grade 11 Engineering Graphics and Design Paper 2 question paper from the Eastern Cape November 2020, 6 pages. Read online or download the free PDF. - Page: https://www.hlayiso.com/library/gr11-egd-p2-nov-2020-questionpaper/a88d243b-6377-4536-845b-80709134cf5e - Updated: 2026-09-27 - Subject: Engineering Graphics and Design - Grade: Grade 11 - Document type: Question paper - Year: 2020 - Exam period: Eastern Cape November - Paper: 2 - Curriculum: CAPS - Pages: 6 Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 11](https://www.hlayiso.com/library/grade-11) › [Engineering Graphics and Design](https://www.hlayiso.com/library/grade-11/engineering-graphic-and-design) › [Engineering Graphics and Design Grade 11 P2 2020 QP](https://www.hlayiso.com/library/gr11-egd-p2-nov-2020-questionpaper/a88d243b-6377-4536-845b-80709134cf5e) ## About this document Engineering Graphic And Design · Grade 11 · Eastern Cape November · 2020. Question paper, 6 pages. Read online or download the PDF. Read it free online on the page above; download the PDF from there. ## Document text Text extracted from the PDF. Layout, diagrams and tables may not survive extraction. ### Page 1 Downloaded from hlayiso.com INSTRUCTIONS AND INFORMATION 1. The question paper consists of FOUR questions. 2. Answer ALL the questions. 3. ALL drawings must be drawn to scale 1 : 1, unless otherwise stated. 4. ALL questions must be answered on the answer sheets provided. 5. ALL the answer sheets must be re-stapled in numerical sequence and handed in irrespective of whether the question was attempted or not. 6. Careful time management is essential in order to complete all the questions. 7. Print your name in the block provided on every ANSWER SHEET. ISEBE LEMFUNDO LEMPUMA KOLONI 8. ALL answers must be drawn accurately and neatly. EASTERN CAPE EDUCATION DEPARTMENT 9. Any details or dimensions not given must be estimated in good proportion. OOS-KAAP ONDERWYSDEPARTEMENT 10. ALL drawings are in third angle orthographic projection, unless otherwise stated . FOR OFFICIAL USE ONLY MODERATED NATIONAL SENIOR CERTIFICATE MARK 1 2 3 4 GRADE 11 TOTAL 2 0 0 2 0 0 FINAL CONVERTED CHECKED BY MARK ENGINEERING GRAPHICS AND DESIGN P2 NOVEMBER 2020 100 FINAL EXAMINATION COMPLETE THE FOLLOWING: NAME NAME MARKS: 200 EXAMINATION CENTRE TIME: 3 hours This question paper consists of 6 pages. SCHOOL Copyright reserved Please turn over 1 ### Page 2 Engineering graphics and design / P2 LE Downloaded from hlayiso.com NSC QUESTION 1: ANALYTICAL (MECHANICAL) EC / November 2020 AP ST Given: A detail drawing of a spanner, a title block, assembled views and a table of questions. The drawings have not been prepared to the indicated scale. Instructions: GEDORE u Complete the table below by neatly answering the questions, which all refer to the accompanying drawings and the title block. [32] QUESTIONS ANSWERS VIEW 1 1 What is the name of the manufacturing company? 1 2 In which town is the manufacturer based? 1 3 What is the drawing number? 1 4 What is the file name? 1 5 Who prepared the drawing? 1 6 Who approved the drawing? 1 7 How many days did it take for the drawing to be approved after it was 2 R8 checked? v A 8 From which material is the shaft manufactured? 1 4 9 How many revisions were made? 1 GEDORE R7 12 28 10 How many rivets must be manufactured? 1 4 11 Which part of the spanner swivels? 1 10 A R8 VIEW 2 12 What machine must be used to form the rivet head? 1 Ø6 13 What is the height of the "word", that is cast into the spanner, at u? 2 8 R6 What type of section is shown at v? 6 14 1 10° 20° 15 What is VIEW 1 called? 1 2 50 22 4 16 What is VIEW 3 called? 2 15 17 What is VIEW 4 called? 2 SHAFT [1] VIEW 3 Ø9 Ø6 R8 w 2 x 2 R12 18 Determine the complete dimensions at: R5 y 1 6 z 2 21 19 In the space below (ANSWER 19), draw, in neat freehand, the SANS symbol for the projection system used. 4 B 10 B R8 TOTAL 32 3 RIVET [2] y USE PNEUMATIC GUN TO FORM RIVET HEAD R5 8 244 MAIN STREET Ø6 BUFFALO LUSIKISIKI 24 w x 4820 METALWORKS MANUFACTURES 13 ' 073 532 0791 TITLE: VIEW 4 z ANSWER 19 GEDORE SPANNER 625 RING HEAD [3] VIEW 5 ALL UNDIMENSIONED RADII ARE R1. ALL DIMENSIONS ARE IN PARTS LIST REVISIONS DATE SCALE 2:1 SURNAME DATE MILLIMETRES. PROGRAMME: AUTOCAD 2020 FINISH: PART QUANTITY MATERIAL 1. FILE NAME: lak78.dwg 0.05 MACHINED 1. SHAFT 1 CHROMIUM-VANADIUM DRAWN: XONGO 2020/03/03 2. NAME DRAWING NO.: DOEEC-20 2. RIVET 1 ALUMINUM CHECKED: LAWE 2020/03/15 3. C QUANTITY: 5 000 3. RING HEAD 1 CHROMIUM-VANADIUM APPROVED: TONA 2020/03/18 4. NAME 2 Copyright reserved Please turn over ### Page 3 Engineering graphics and design / P2 LE Downloaded from hlayiso.com NSC QUESTION 2: CAM EC / November 2020 AP ST Given: · The detail of a camshaft and a follower in its lowest position. · The centre lines of the cam profile. Specifications: · The follower reciprocates on the vertical centre line of the camshaft. · Minimum distance from the cam profile to the centre of the camshaft = 15 mm. · Rotation = anti-clockwise Motion: The cam imparts the following motion to the follower: · It rises 10 mm with uniform motion over the first 30°. · It rises 25 mm with uniform motion over the next 30°. · It rises 20 mm with uniform motion over the next 60°. · It descends 10 mm with uniform motion over the next 60°. · There is a dwell period for the next 60°. · It returns to the original position with uniform motion over the rest of the rotation. Instructions: · Draw, to scale 1 : 1, the given camshaft and the wedge-shaped follower detail at its minimum position. C · Show the direction of rotation on the cam profile. · Draw to a rotational scale of 360° = 120 mm and a displacement scale of 1 : 1, the complete displacement graph for the required motion. · Label the displacement graph and include the scale. · Project and draw the cam profile that would generate the given motion. · Show ALL necessary constructions and projections. [39] ASSESSMENT CRITERIA 10 1 GIVEN + MIN. DISTANCE 5 2 GRAPH CONSTRUCTION 3 3 PERPENDICULAR HEIGHT 5 62 UNIFORM MOTION + 4 DWELL 4 60° 5 GRAPH LABEL + SCALE 2 6 CAM CONSTRUCTION 13 15 C 7 CAM + CURVE QUALITY 7 Ø10 TOTAL 39 NAME NAME 3 Copyright reserved Please turn over ### Page 4 Engineering graphics and design / P2 LE Downloaded from hlayiso.com NSC QUESTION 3: ISOMETRIC DRAWING EC / November 2020 AP ST Given: · The front view, top view and right view of a connection bracket. · The position of point S on the drawing sheet. Instructions: Using scale 1 : 1, convert the orthographic views of the connecting bracket into an isometric drawing. · Make S the lowest point of the drawing. · Show ALL necessary construction. · NO hidden detail is required. [48] 16 40 17 12 44 18 38 £ 64 8 13 S 24 30 12 ½ HEXAGON 72 20 10 24 16 8 48 S S 44 12 ASSESSMENT CRITERIA 1 AUX' VIEW + PLACING 4 2 ISOMETRIC LINES 22½ S 3 SQUARE + SLOT 9½ 4 HEXAGON 5½ CIRCLE + 5 CIRCLE CONST. 4½ 6 CENTRE LINES 2 TOTAL 48 NAME NAME 4 Copyright reserved Please turn over ### Page 5 Engineering graphics and design / P2 LE Downloaded from hlayiso.com NSC EC / November 2020 AP QUESTION 4: MECHANICAL ASSEMBLY ST Given: 1 · Orthographic views of each of the parts of a pipe vice assembly. 124 10 Ø24 · The exploded isometric drawing of the parts of a pipe Ø16 45° Ø16 vice assembly, showing the position of each part relative M10 120° to all the others. M10 3 · Starting point S, with the incomplete front view of the 10 3 3 movable jaw and starting point T, with the incomplete Ø20 HANDLE BAR [1] 2 right view of the movable jaw and -vice base, on page 6. HANDLE BAR CAP [2] 45° Instructions: · Answer this question on page 6. Ø10 R13 22 · Draw, to scale 1 : 1 and in third-angle orthographic 168 projection, the following views of the assembled parts of 69 the pipe vice assembly: 6 4.1 The front view of the pipe vice assembly as seen 33 30 30 15 M16 100 from the direction of the arrow on the exploded isometric drawing. R8 4.2 A half-sectional right view on cutting plane A-A. Ø16 Show the left half in section. The cutting plane is shown on the top view of the vice base (part 4). A 3 6 NOTE: 30 Ø24 9 30° · Planning of the layout of the views is essential. Ø8 · All drawings must comply with the guidelines as 15 A Ø12 contained in the SANS 10111. 53 4 · Show, in the front view, THREE faces of the M16 bolt. SCREW ROD [3] · Show all bolt constructions. M16 · NO hidden detail is required. 45° 3 [81] 18 R8 R8 9 21 FR ON 7 R8 9 TV 72 Ø8 IEW R9 174 Ø12 R35 M6 5 PARTS LIST 42 23 20 PART MATERIAL QUANTITY T 1. HANDLE BAR STEEL 1 S 2. HANDLE BAR CAP STEEL 1 86 86 3. SCREW ROD STEEL 1 30 9 5 4. VICE BASE CAST IRON 1 5. MOVABLE JAW MS 1 120° 6 15 M6 2 6. M16 BOLT MS 1 60 10 7. SET SCREW MS 2 8 18 22 10 2 Ø4 TITLE: 42 42 9 42 3 93 S 15 30 15 PIPE VICE 2 BUFFALO 244 MAIN STREET LUSIKISIKI 4820 METALWORKS MANUFACTURERS ' 073 532 0791 VICE BASE [4] MOVABLE JAW [5] M16 BOLT [6] SET SCREW [7] ALL DIMENSIONS ARE METRIC. ALL UNDIMENSIONED RADII ARE R 4. 5 Copyright reserved Please turn over ### Page 6 Engineering graphics and design / P2 LE Downloaded from hlayiso.com NSC PENALTIES EC / November 2020 AP ST 1 WRONG SCALE -2 2 WRONG PLACING OF VIEWS -2 3 PARTS NOT ASSEMBLED -2 4 WRONG HATCHING -2 TOTAL PENALTIES (-) ASSESSMENT CRITERIA FRONT VIEW 1 HANDLE BAR 4½ 2 SCREW ROD 6½ 3 HANDLE BAR CAP 3½ 4 M15 BOLT 9½ 5 VICE BASE 12 6 CENTRE LINES 2 7 ASSEMBLY 3 SUB-TOTAL 41 HALF SECTIONAL RIGHT VIEW 1 HANDLE BAR 1 2 SCREW ROD 10 3 HANDLE BAR CAP 1½ S T 4 M15 BOLT 4½ 5 VICE BASE 17½ 6 MOVABLE JAW 4½ 7 CENTRE LINES 1 SUB-TOTAL 40 TOTAL 81 PENALTIES (-) TOTAL NAME NAME 6 Copyright reserved ## Related documents - [GR11 EGD P2 NOV 2020 MARKING GUIDELINE](https://www.hlayiso.com/library/gr11-egd-p2-nov-2020-marking-guideline/5918f9c4-9af0-4cc7-bfc2-2b4b68700c55) — Engineering Graphic and Design · Memo · 2020 - [GR11 IGO V2 NOV 2020 NASIEN RIGLYN](https://www.hlayiso.com/library/gr11-igo-v2-nov-2020-nasien-riglyn/18b1d04d-4bcf-4604-b743-2a9223b56bf3) — Engineering Graphic and Design · QP · 2020 - [GR11 IGO V2 NOV 2020 VRAESTEL](https://www.hlayiso.com/library/gr11-igo-v2-nov-2020-vraestel/d28bdaf2-ee3b-48ed-a5b0-0f2847b17ebd) — Engineering Graphic and Design · QP · 2020 - [EGD P1 GR11 NOV2020 QP ENG D](https://www.hlayiso.com/library/egd-p1-gr11-nov2020-qp-eng-d/33ec3c9c-0d6f-46e0-8004-27e114ea193c) — Engineering Graphic and Design · QP · 2020 · Eng - [EGD P1 GR11 NOV2020 QP AFR D](https://www.hlayiso.com/library/egd-p1-gr11-nov2020-qp-afr-d/50789484-ecd0-4022-93cb-f02646e54f26) — Engineering Graphic and Design · QP · 2020 · Afr - [GR11 EGD P2 NOV 2020 QUESTIONPAPER](https://www.hlayiso.com/library/grade-11-engineering-graphic-and-design-2020-national-exemplar-november-exam-question-paper-paper-2/598ae231-66ec-402a-abfe-9749f0ba2356) — Engineering Graphic and Design · QP · 2020 ## More from Grade 11 Engineering Graphics and Design - [Gr 11 EngGraph Des ATP 2023-24](https://www.hlayiso.com/library/gr-11-enggraph-des-atp-2023-24/6fbec59e-8df9-49dc-9042-1e84389c22fa) — ATP - [EGD P1 GR11 MEMO NOV2022 Afr+Engl](https://www.hlayiso.com/library/egd-p1-gr11-memo-nov2022-afr-engl/dc8a6861-4564-49b7-9da7-af10cd3460f8) — Memo · 2022 · Afr - [EGD P2 GR11 MEMO NOV2022 Afrikaans](https://www.hlayiso.com/library/egd-p2-gr11-memo-nov2022-afrikaans/085022c0-c1e2-44e3-8f13-b13c4d9661fd) — Memo · 2022 · Afr - [EGD P2 GR11 MEMO NOV2022 English](https://www.hlayiso.com/library/egd-p2-gr11-memo-nov2022-english/50c4e044-b732-4d91-bcb3-e98c1bc8bfc1) — Memo · 2022 · Eng - [EGD P1 GR11 MEMO NOV2022 Afr+Engl](https://www.hlayiso.com/library/grade-11-engineering-graphic-and-design-2022-exemplar-november-exam-memorandum-paper-1-english/9926f9cd-76bc-4eff-a287-c1394b665aaf) — Memo · 2022 · Eng - [EGD P2 GR11 MEMO NOV2022 Afrikaans](https://www.hlayiso.com/library/grade-11-engineering-graphic-and-design-2022-exemplar-november-exam-memorandum-paper-2-afrikaans/964722fb-b9df-42a0-a525-cbab4bbad105) — Memo · 2022 · Afr ## Collection - [Grade 11 past papers](https://www.hlayiso.com/grade-11/past-papers) --- Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.