# Mechanical Technology Grade 12 NSC June 2024 QP (Eng)

> Grade 12 Mechanical Technology question paper from the NSC June Exam 2024 (English), 18 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d
- Updated: 2026-09-28
- Subject: Mechanical Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2024
- Exam period: NSC June Exam
- Curriculum: CAPS
- Pages: 18

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC June 2024 QP (Eng)](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d)

## About this document

Mechanical Technology · Grade 12 · NSC June Exam · 2024 · English. Question paper, 18 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Confidential

             SENIOR CERTIFICATE EXAMINATIONS/
         NATIONAL SENIOR CERTIFICATE EXAMINATIONS

               MECHANICAL TECHNOLOGY: AUTOMOTIVE

                                MAY/JUNE 2024

                                                                       MARKS: 200

                                                                      TIME: 3 hours

        This question paper consists of 16 pages and a 2-page formula sheet.

Copyright reserved                                                    Please turn over

### Page 2

Mechanical Technology: Automotive             2                            DBE/May/June 2024
                                       SC/NSC Confidential

INSTRUCTIONS AND INFORMATION

1.         Write your centre number and examination number in the spaces provided on
           the ANSWER BOOK.

2.         Read ALL the questions carefully.

3.         Answer ALL the questions.

4.         Number the answers correctly according to the numbering system used in this
           question paper.

5.         Start EACH question on a NEW page.

6.         Show ALL calculations and units. Round off final answers to TWO decimal
           places.

7.         Candidates may use non-programmable scientific calculators and drawing
           instruments.

8.         The value of gravitational acceleration should be taken as 9,81 m/s2 or
           10 m/s2.

9.         ALL dimensions are in millimetres, unless stated otherwise in the question.

10.        Write neatly and legibly.

11.        A formula sheet is attached at the end of the question paper.

12.        Use the criteria below to assist you in managing your time.

                                                                                TIME IN
QUESTION                            CONTENT                      MARKS
                                                                                MINUTES
                                 GENERIC
      1         Multiple-choice Questions                            6               6
      2         Safety                                              10              10
      3         Materials                                           14              14
                                 SPECIFIC
      4         Multiple-choice Questions                           14              10
      5         Tools and Equipment                                 23              20
      6         Engines                                             28              25
      7         Forces                                              32              25
      8         Maintenance                                         23              20
      9         Systems and Control (Automatic Gearbox)             18              20
                Systems and Control (Axles, Steering
      10                                                            32              30
                Geometry and Electronic)
                                                     TOTAL         200             180

Copyright reserved                                                            Please turn over

### Page 3

Mechanical Technology: Automotive            3                            DBE/May/June 2024
                                      SC/NSC Confidential

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E.

1.1       Which of the following refers to the Occupational Health and Safety Act
          (OHSA), 1993 (Act 85 of 1993) when responding to HIV/Aids in the
          workplace?

          A     It is the duty of employers to make sure that rubber gloves and surgical
                masks are available in all first-aid kits.
          B     This Act emphasises the working relationship between employees and
                employers.
          C     It explains the minimum standards that employees and employers can
                expect from one another in the workplace.
          D     The purpose of this Act is to create an environment of equality in the
                workplace.                                                                        (1)

1.2       Which ONE of the following statements refers to process layout?

          A     The machines are arranged in the sequence in which operations are
                carried out.
          B     The different stages of production are carried out in different
                departments.
          C     The process is ideal for mass production.
          D     The time period of the manufacturing cycle is shorter.                            (1)

1.3       What is the function of the pressure gauge in a hydraulic press?

          A     To be able to observe the working pressure
          B     To support the jig on the platform
          C     To stabilise the frame on the support pins
          D     To hold the work piece in place                                                   (1)

1.4       Why is steel soaked at a specific temperature during heat treatment?

          A     To ensure that the outside of the steel becomes hotter than the inside
          B     To ensure that the inside of the steel becomes hotter than the outside
          C     To prevent a loss in the carbon content of the steel
          D     To ensure uniform penetration of heat                                             (1)

1.5       Which ONE of the following quenching media is used for the normalising of
          steel?

          A     Oil
          B     Liquid salts
          C     Still air
          D     Brine                                                                             (1)

Copyright reserved                                                             Please turn over

### Page 4

Mechanical Technology: Automotive           4                           DBE/May/June 2024
                                     SC/NSC Confidential

1.6       The metal that is best suited for case-hardening:

          A     Brass
          B     Aluminium
          C     Mild steel
          D     Cast iron                                                                       (1)
                                                                                                [6]

QUESTION 2: SAFETY (GENERIC)

2.1       State TWO situations when basic first aid should be given to help and support
          a person at the workplace.                                                            (2)

2.2       FIGURE 2.2 below shows a safety sign at a bench grinder. Explain what is
          meant by the signs labelled A–D.

                              B
                                                                  C

                              A                                   D

                                           FIGURE 2.2                                           (4)

2.3       State TWO safety precautions that should be adhered to when using a drill
          press.

          NOTE: All PPE and environmental factors have been taken care of.                      (2)

2.4       State TWO safety precautions that an operator should adhere to while
          working on a surface grinder.

          NOTE: All PPE and environmental factors have been taken care of.                      (2)
                                                                                                [10]   2024

Copyright reserved                                                           Please turn over

### Page 5

Mechanical Technology: Automotive               5                       DBE/May/June 2024
                                         SC/NSC Confidential

QUESTION 3: MATERIALS (GENERIC)

3.1       State whether steel is heated either below or above the critical temperature
          during the following heat-treatment processes:

          3.1.1        Hardening                                                                 (1)

          3.1.2        Tempering                                                                 (1)

          3.1.3        Normalising                                                               (1)

3.2       The hardness of a sampled work piece is tested using a drill press. Which
          TWO aspects should be observed on the cutting chips?                                   (2)

3.3       Besides the machinability test, name THREE other tests used to determine
          the different types of steels.                                                         (3)

3.4       Name TWO quenching methods used for case-hardening.                                    (2)

3.5       How can the temperature of a work piece be determined during the heat-
          treatment process?                                                                     (1)

3.6       State the THREE basic steps that are involved in all heat-treatment processes
          according to a time-temperature cycle.                                                 (3)
                                                                                                 [14]

QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 E.

4.1       What is measured during a compression test?

          A       The compression pressure developed in the cylinder
          B       The amount of leakage from the cylinder in percentage
          C       The amount of exhaust gases leaving the cylinder
          D       The compression ratio developed on the compression stroke                      (1)

4.2       When performing wheel alignment, the turntables are used to measure
          the …

          A       camber angle.
          B       caster angle.
          C       angle at which the wheel is turned left or right.
          D       king pin inclination.                                                          (1)

4.3       What is the function of the waste gate on a turbocharger?

          A       To cool the turbocharger components
          B       Allows the exhaust gases to bypass the turbine
          C       To release excess manifold pressure
          D       Guides exhaust gases onto the turbine                                          (1)

Copyright reserved                                                            Please turn over

### Page 6

Mechanical Technology: Automotive             6                         DBE/May/June 2024
                                       SC/NSC Confidential

4.4       Identify the vibration damper shown in FIGURE 4.4 below.

                                             FIGURE 4.4

          A     Combined rubber and friction disc
          B     Flat belt pulley
          C     Flywheel pulley
          D     Friction face                                                                   (1)

4.5       When a force overcomes resistance and causes movement in a straight line,
          it is known as …

          A     power.
          B     torque.
          C     work.
          D     revolutions.                                                                    (1)

4.6       Power can be defined as the …

          A     rate at which work is done.
          B     distance over which work is done.
          C     speed at which work is done.
          D     ability to do work.                                                             (1)

4.7       Which ONE of the following is the reason that the mechanical efficiency of an
          engine is always less than 100%?

          A     A faulty MAF sensor
          B     Frictional loss in the engine
          C     Fuel octane rating that is incorrect
          D     A faulty MAP sensor                                                             (1)

4.8       How can the rated pressure of the radiator cap be obtained?

          A     Read it off the radiator cap
          B     Read it off the intake manifold
          C     Obtain it on the tappet cover
          D     Check it on the pressure tester specifications                                  (1)

Copyright reserved                                                           Please turn over

### Page 7

Mechanical Technology: Automotive              7                         DBE/May/June 2024
                                        SC/NSC Confidential

4.9       Excessively high fuel pressure before the fuel injector is caused by …

          A     clogged fuel lines before the fuel filter.
          B     a dirty fuel filter.
          C     a faulty pressure regulator.
          D     low voltage to the fuel pump.                                                    (1)

4.10      Identify the annulus shown in FIGURE 4.10 below.

                              2

                                                                  3

                               1                                  4

                                             FIGURE 4.10

          A     1
          B     2
          C     3
          D     4                                                                                (1)

4.11      Which component of the torque convertor initiates the movement of the
          turbine shaft?

          A     Turbine
          B     One-way clutch
          C     Pump
          D     Housing                                                                          (1)

Copyright reserved                                                            Please turn over

### Page 8

Mechanical Technology: Automotive           8                          DBE/May/June 2024
                                     SC/NSC Confidential

4.12      The tyre wear pattern shown in FIGURE 4.12 below is caused by …

                                      One side of thread
                                      worn excessively

                                          FIGURE 4.12

          A     incorrect camber.
          B     excessive wheel imbalance.
          C     over-inflated wheel.
          D     underinflated twheel.                                                          (1)

4.13      A sensor can be defined as a/an …

          A     control unit.
          B     input unit.
          C     output unit.
          D     actuator.                                                                      (1)

4.14      What is the function of the manifold absolute pressure (MAP) sensor?

          A     Measures the engine load conditions
          B     Controls the position of the throttle
          C     Updates the ECU of the engine speed
          D     Measures the air intake volume                                                 (1)
                                                                                               [14]

Copyright reserved                                                          Please turn over

### Page 9

Mechanical Technology: Automotive            9                         DBE/May/June 2024
                                      SC/NSC Confidential

QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)

5.1       FIGURE 5.1 below shows a compression tester. Answer the questions that
          follow.

                                                    B
                                                               C

                               A

                                            FIGURE 5.1

          5.1.1      State the function of parts A, B and C.                                  (3)

          5.1.2      Why should the battery voltage be tested before performing a
                     compression test?                                                        (2)

          5.1.3      Give TWO reasons why the wet compression test is performed
                     after the dry compression test.                                          (2)

5.2       Give a reason why EACH of the following set-up procedures are done during
          a cylinder leakage test:

          5.2.1      Calibrate (zero) the tester                                              (1)

          5.2.2      Turn the engine until the piston is at TDC on the compression
                     stroke                                                                   (1)

          5.2.3      Lock the crankshaft                                                      (1)

5.3       Name FOUR gases, excluding nitrogen oxide (NOx), that can be analysed by
          an exhaust gas analyser.                                                            (4)

5.4       A vehicle needs to be scanned using an OBD-II scanner. Answer the
          questions below.

          5.4.1      State TWO specifications required before an OBD-II scan can be
                     done.                                                                    (2)

          5.4.2      State the TWO basic functions of an OBD-II scanner.                      (2)

Copyright reserved                                                         Please turn over

### Page 10

Mechanical Technology: Automotive            10                          DBE/May/June 2024
                                      SC/NSC Confidential

5.5       How is dynamic wheel balancing corrected after the balance is checked on a
          wheel balancer?                                                                       (2)

5.6       FIGURE 5.6 below shows wheel alignment equipment. Answer the questions
          that follow.

                                           FIGURE 5.6

          5.6.1      Identify the specific equipment.                                           (1)

          5.6.2      State the function of the equipment.                                       (1)

          5.6.3      What is the unit of measurement of the equipment?                          (1)
                                                                                                [23]

QUESTION 6: ENGINES (SPECIFIC)

6.1       The following questions are based on the crankshaft of an internal
          combustion engine.

          6.1.1      Which component, fitted to the nose of the crankshaft, reduces
                     vibrations?                                                                (1)

          6.1.2      Describe TWO ways of modifying crankshaft counterweights to
                     reduce vibrations.                                                         (2)

          6.1.3      Which component is bolted around the big-end journal?                      (1)

          6.1.4      State THREE causes of crankshaft twist during engine operation.            (3)

6.2       Which THREE components are part of the rotating mass on an internal
          combustion engine?                                                                    (3)

Copyright reserved                                                           Please turn over

### Page 11

Mechanical Technology: Automotive            11                            DBE/May/June 2024
                                      SC/NSC Confidential

6.3       FIGURE 6.3 below shows engine cylinder layouts. Answer the questions that
          follow.

                        A                       B                      C
                                            FIGURE 6.3

          6.3.1      Identify the different types of engine layouts.                              (3)

          6.3.2      State TWO advantages of engine layout A compared to engine
                     layout B.                                                                    (2)

6.4       State the degrees of crankshaft rotation between power impulses for EACH of
          the following four-stroke engines:

          6.4.1      Four-cylinder                                                                (1)

          6.4.2      Six-cylinder                                                                 (1)

          6.4.3      Eight-cylinder                                                               (1)

6.5       FIGURE 6.5 below shows a turbocharger that is fitted to an internal
          combustion engine. Answer the questions that follow.

                                                                       D

                                                                       C

                                                            B

                       A

                                            FIGURE 6.5

          6.5.1      Label A–D.                                                                   (4)

          6.5.2      Which part in a variable geometry turbocharger helps to speed up
                     the rotation of the turbocharger at low speed?                               (1)

Copyright reserved                                                             Please turn over

### Page 12

Mechanical Technology: Automotive              12                         DBE/May/June 2024
                                        SC/NSC Confidential

6.6       Name THREE types of superchargers used on an internal combustion engine.               (3)

6.7       State TWO disadvantages             of   superchargers   when   compared     to
          turbochargers.                                                                         (2)
                                                                                                 [28]

QUESTION 7: FORCES (SPECIFIC)

7.1       Define the following terms:

          7.1.1      Torque                                                                      (2)

          7.1.2      Brake power                                                                 (2)

7.2       Explain ONE method of increasing the swept volume of an internal
          combustion engine.                                                                     (1)

7.3       The following measurements were obtained from an internal combustion
          engine:

          Bore diameter:                74 mm
          Stroke length:                77 mm
          Clearance volume:             42 mℓ

          Calculate the following:

          7.3.1      Swept volume                                                                (3)

          7.3.2      Compression ratio                                                           (4)

          7.3.3      The new stroke length in millimetres (mm) if the compression ratio
                     is increased to 10 : 1. The clearance volume and bore diameter
                     remain unchanged.                                                           (6)

7.4       The following data was obtained on a four-cylinder four-stroke engine:

          Mean effective pressure:      950 kPa
          Engine speed:                 2 500 r/min
          Bore diameter:                65 mm
          Stroke length:                70 mm
          Brake arm length:             0,4 m
          Scale reading:                142,5 N

          Calculate the following:

          7.4.1      Indicated power in kW                                                       (7)

          7.4.2      Torque                                                                      (2)

          7.4.3      Brake power in kW                                                           (3)

          7.4.4      Mechanical efficiency                                                       (2)
                                                                                                 [32]

Copyright reserved                                                            Please turn over

### Page 13

Mechanical Technology: Automotive           13                       DBE/May/June 2024
                                     SC/NSC Confidential

QUESTION 8: MAINTENANCE (SPECIFIC)

8.1       Answer the following questions on the exhaust gas analysis on an internal
          combustion engine:

          8.1.1      State TWO results of vacuum leaks.                                     (2)

          8.1.2      State THREE possible causes of a high nitrogen oxide (NOx)
                     reading.                                                               (3)

8.2       TABLE 8.2 below shows the faults, causes and corrective measures of a dry
          compression test. Complete the table by writing only the question numbers
          (8.2.1 to 8.2.4) and the answers in the ANSWER BOOK.

                                                                  CORRECTIVE
                     FAULTS               POSSIBLE CAUSES
                                                                   MEASURES
          Gauge rises in smaller jumps,
          and compression pressure                 8.2.1               8.2.2
          reading is low
                       8.2.3                 Slipped cambelt           8.2.4
                                           TABLE 8.2                                        (4)

8.3       A cylinder leakage test shows that air is leaking from the combustion
          chamber. State where hissing sounds would be heard if air is leaking
          from/pass the following components:

          8.3.1      Piston rings                                                           (1)

          8.3.2      Intake valve                                                           (1)

          8.3.3      Exhaust valve                                                          (1)

8.4       State THREE manufacturerʹs specifications required to do an oil pressure
          test.                                                                             (3)

8.5       State TWO causes of a low fuel pressure reading on a fuel pressure tester
          and give the corrective measure for EACH of the causes.                           (4)

8.6       Explain in FOUR steps how to perform a cooling system pressure test after
          the radiator cap is removed.                                                      (4)
                                                                                            [23]

Copyright reserved                                                       Please turn over

### Page 14

Mechanical Technology: Automotive              14                                DBE/May/June 2024
                                        SC/NSC Confidential

QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)

9.1       State THREE advantages of an automatic gearbox fitted with a torque
          converter.                                                                                      (3)

9.2       FIGURE 9.2 below shows a torque converter                       used    in   automatic
          transmissions. Answer the questions that follow.

                                    A                             B

                                                              C

                                                                      D

                                             FIGURE 9.2

          9.2.1      Label parts A–D.                                                                     (4)

          9.2.2      Define the term stall speed in a torque converter.                                   (2)

          9.2.3      Explain what happens when a torque converter stops multiplying
                     torque during driving.                                                               (2)

9.3       State TWO advantages of a transmission control unit in an automatic
          transmission system.                                                                            (2)

9.4       Describe TWO built-in features used to cool the automatic transmission fluid
          (ATF) used in a motor vehicleʹs transmission.                                                   (2)

9.5       Explain, in the CORRECT sequence, how forward overdrive is obtained in the
          double epicyclic gear system.                                                                   (3)
                                                                                                          [18]

Copyright reserved                                                                     Please turn over

### Page 15

Mechanical Technology: Automotive              15                      DBE/May/June 2024
                                        SC/NSC Confidential

QUESTION 10:         SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY
                     AND ELECTRONICS) (SPECIFIC)

10.1      State TWO improvements that result from correcting the wheel alignment.              (2)

10.2      FIGURE 10.2 below shows an independent front suspension. Answer the
          questions that follow.

                                           B

                                    A

                                                              C

                                                                  D

                                             Offset

                                        As seen from the front
                                             FIGURE 10.2

          10.2.1     Label A–D.                                                                (4)

          10.2.2     How is the camber adjusted on a vehicle?                                  (1)

          10.2.3     State TWO negative effects of excessive positive camber.                  (2)

10.3      State THREE pre-checks that must be done on a wheel before dynamic
          wheel balancing.                                                                     (3)

10.4      State TWO functions of each of the following components in the fuel-delivery
          system:

          10.4.1     Pressure regulator                                                        (2)

          10.4.2     Fuel pump                                                                 (2)

Copyright reserved                                                          Please turn over

### Page 16

Mechanical Technology: Automotive                 16                          DBE/May/June 2024
                                        SC/NSC Confidential

10.5      State TWO operating conditions that affect ignition timing.                             (2)

10.6      FIGURE 10.6 below shows a common rail direct injection (CRDI) system.
          Label A–D.

                                                                              D
                                    A              B            C

                                                FIGURE 10.6                                       (4)

10.7      State TWO requirements for a catalytic converter to function effectively.               (2)

10.8      FIGURE 10.8 below shows a three-phase alternator circuit diagram. Answer the
          questions that follow.

                     A          B                  rectifier    capacitor

                                                                      to regulator

                                                                                     C

                                                FIGURE 10.8

          10.8.1         Label components A–C.                                                    (3)

          10.8.2         How many diodes are in this circuit?                                     (1)

          10.8.3         State the function of the diodes.                                        (2)

10.9      State TWO methods of deactivating speed control while driving.                          (2)
                                                                                                  [32]

                                                                                     TOTAL:       200
Copyright reserved

### Page 17

Mechanical Technology: Automotive              1                       DBE/May/June 2024
                                     SC/NSC Confidential

         FORMULA SHEET FOR MECHANICAL TECHNOLOGY: AUTOMOTIVE

   1.          F  ma

               Where:
                        m = Mass
                        a = Acceleration

   2.          Work done = Force × Displacement            OR     W Fs

                          Force  Displacement                         Fs
   3.          Power                                      OR     P
                                  Time                                  t

   4.          Torque  Force  Radius                     OR     T Fr

   5.          IP  P  L  A  N  n

               Where:

                       IP  Indicated power
                        P  Mean effective pressure
                        L  Stroke length
                        A  Area of piston crown
                        N  Number of power strokes per second
                        n  Number of cylinders

   6.          BP = 2 π N T

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     T  Torque

   7.          Brake power with Pröny brake = 2  π  N  F  R

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     F  Force
                     R  Brake arm length

Copyright reserved                                                        Please turn over

### Page 18

Mechanical Technology: Automotive                2                 DBE/May/June 2024
                                       SC/NSC Confidential

                                          BP
   8.          Mechanical efficiency =        100%
                                          IP

                                       SV  CV
   9.          Compression ratio 
                                         CV

               Where:

                     SV  Swept volume
                     CV  Clearance volume

                    πD 2
   10.         SV =      L
                     4

               Where:
                     D  Bore diameter
                     L  Stroke length

                        SV
   11.         CV =
                       CR - 1

                                Product of teeth on driven gears
   12.         Gear ratio =
                                Product of teeth on driver gears

Copyright reserved

## Related documents

- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Mechanical Technology · Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Mechanical Technology · Memo · 2024 · Eng
- [MECH TECH GR12 QP SEPT 2020 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87) — Mechanical Technology · QP · 2020 · Eng
- [MECH TECH GR12 QP SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162) — Mechanical Technology · QP · 2020 · Eng
- [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Welding & Metalwork) Eng](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-eng/c6bfa7b8-3601-4a11-9be4-55ee65e4011f) — Mechanical Technology · QP · 2023 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Memo · 2023 · Eng
- [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Memo · 2023 · Eng
- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — QP · 2023 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
