# Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

> Grade 12 Mechanical Technology memorandum from the Eastern Cape Mock Exam 2023 (English), 16 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Language: English
- Document type: Memorandum
- Year: 2023
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 16

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49)

## About this document

Mechanical Technology · Grade 12 · Eastern Cape Mock Exam · 2023 · English. Memorandum, 16 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

NATIONAL
                 SENIOR CERTIFICATE

                         GRADE 12

                  SEPTEMBER 2023

    MECHANICAL TECHNOLOGY: FITTING AND
                MACHINING
            MARKING GUIDELINE

MARKS:   200

               This marking guideline consists of 16 pages.

### Page 2

2               MECHANICAL TECHNOLOGY (FITTING AND MACHINING)             (EC/SEPTEMBER 2023)

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

1.1    C✓                                                                                 (1)
1.2    D✓                                                                                 (1)
1.3    C✓                                                                                 (1)
1.4    C✓                                                                                 (1)
1.5    A✓                                                                                 (1)
1.6    B✓                                                                                 (1)
                                                                                          [6]

QUESTION 2: SAFETY (GENERIC)
2.1    Arc welding safety precautions:
       • Wear correct PPE 
       • Ensure the electrode holder is well insulated 
       • The environment must be free of water and combustible materials 
       • Ensure the environment is well ventilated                 (Any 3 x 1)           (3)
2.2    Pedestal drilling machine safety precautions:
       • Wear correct PPE 
       • Make sure all guards are in place 
       • Clamp the workpiece securely 
       • Use the correct drill bit 
       • Do not make any adjustment while the machine is in motion 
       • Use the correct speed 
       • Do not remove chips by hand                                (Any 2 x 1)          (2)
2.3    Manual guillotine maximum cutting thickness is 1,20 mm                            (1)
2.4    2.4.1    Advantages of product layout:
                • Handling of material is limited to a minimum. 
                • Time period of manufacturing cycle is less. 
                • Production control is almost automatic. 
                • Greater use of unskilled labour is possible. 
                • Less total inspection is required. 
                • Less total floor space is needed per unit of production. 
                                                                          (Any 2 x 1)     (2)
       2.4.2    Advantages of the process layout:
                • High machine utilisation because more than one product is
                  manufactured. 
                • Better supervision as a result of subdivision of processes. 
                • Less interruption in flow of work when machines become
                  defective. 
                • Lower equipment cost, since one machine can produce more
                  than one product. 
                • Better control of total manufacturing cost. 
                • Greater flexibility in the production process.         (Any 2 x 1)     (2)
                                                                                         [10]

Copyright reserved                                                             Please turn over

### Page 3

(EC/SEPTEMBER 2023)      MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                     3

QUESTION 3: MATERIALS (GENERIC)

3.1    Purpose of case hardening:
       • To produce a hard case over  and tough core.                                   (2)

3.2    Using high carbon steel for case hardening:
       • The hardness will penetrate the core ✓                                           (1)

3.3    Factors of hardness:
       • Work piece size 
       • Quenching rate 
       • Carbon content                                                                  (3)

3.4    Types of quenching mediums:
       • Water and salt (brine) 
       • Tap water 
       • Liquid salts 
       • Molten lead 
       • Soluble oil and water 
       • Oil                                                            (Any 3 x 1)      (3)

3.5    Colour coding of engineering materials:
       • To identify the type of materials as well as the carbon content of steel ✓       (1)

3.6    Types of test:

       3.6.1     •    Filing test ✓
                 •    Machining test ✓                                   (Any 1 x 1)      (1)

       3.6.2     •    Sound test ✓
                 •    Spark test ✓                                       (Any 1 x 1)      (1)

       3.6.3     •    Bending test ✓                                                      (1)

3.7    Machine for spark test:
       • Pedestal grinding machine ✓                                                     (1)
                                                                                        [14]

Copyright reserved                                                           Please turn over

### Page 4

4                MECHANICAL TECHNOLOGY (FITTING AND MACHINING)   (EC/SEPTEMBER 2023)

 QUESTION 4: MULTIPLE CHOICE QUESTION (SPECIFIC)

 4.1    D    √

 4.2    D    √

 4.3    B    √

 4.4    A    √

 4.5    A    √

 4.6    B    √

 4.7    C    √

 4.8    B    √

 4.9    D    √

 4.10   B    √

 4.11   C    √

 4.12   B    √

 4.13   D    √

 4.14   B    √                                                     (14 x 1)    [14]

Copyright reserved                                                   Please turn over

### Page 5

(EC/SEPTEMBER 2023)      MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                 5

 QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)

 5.1   Cutting depth:
       Cutting depth = 0,866 x P         ✓
                     = 0,866 X 2,5       ✓
                     = 2,17 mm           ✓                                           (3)

 5.2   • Compound slide method           ✓
       • Tail-stock set-over method      ✓                                           (2)

 5.3   Cutting Square Threads

       5.3.1    Lead = Pitch x Number of Starts
                     = 2 x 12     ✓
                     = 24 mm      ✓                                                  (2)

       5.3.2    Mean Diameter = OD – 0.5 Pitch
                              = 100 – 0,5 x 12 ✓
                              = 94 mm          ✓                                     (2)

       5.3.3    Tan θ = Lead / π x Dm
                Tan θ = 24 / 94     ✓
                    θ = 14,32°      ✓                                                (2)

 5.4   Milling Terminology

       5.4.1    Universal horizontal milling machine ✓                               (1)

       5.4.2    Labels

                A – Arbor            ✓
                B – Milling cutter   ✓
                C – Workpiece        ✓
                D – Parallels        ✓
                E – Machine vice     ✓
                F – Machine table                                                    (5)
                                                                                    [18]

Copyright reserved                                                       Please turn over

### Page 6

6               MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                        (EC/SEPTEMBER 2023)

 QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)
 6.1   Advantages of gang milling:
       • Several surfaces can be milled simultaneously.
       • This method is a time saver.
       • It makes production work more effective                                     (Any 2 x 1)    (2)

 6.2   Uses of cutters:
       6.2.1    T-slot milling cutters are designed for cutting T-slots in machine tables
                and similar applications. ✓                                               (1)
       6.2.2    End mill cutters are used for machining slots, keyways, pockets,
                facing narrow faces and cutting profiles. ✓                                         (1)
       6.2.3    Slitting saw cutters are used for parting off and slitting thin sections
                and the cutting of deep and narrow slots. ✓

 6.3   Module is the unit of size that indicates how big or how small a gear is. ✓                  (1)

 6.4   Milling methods
       Up-cut milling

                                                                     ✓✓                             (2)

 6.5   Differential indexing:

                                             Hole circles
         Side 1      24   25     28     30        34        37       38    39   41   42     43
         Side 2      46   47     49     51        53        54       57    58   59   62     66

                                      Standard change gears
         24 x 2      28     32     40        44        48           56    64    72   86     100

       6.5.1    Indexing Required:
                                                       40
                                       Indexing =                    ✓
                                                       𝐴
                                                   = 40/160
                                                        1       7
                                                   =        x        ✓
                                                        4       7
                                               = 7/28
                Indexing is 7 holes in a 28-hole circle. ✓                                          (3)

Copyright reserved                                                                        Please turn over

### Page 7

(EC/SEPTEMBER 2023)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                       7

       6.5.2    Change of gears:
                                𝐷𝑟𝑖𝑣𝑒𝑟       𝐴−𝑁         40
                Gear ratio:              =         x 1            ✓
                                𝐷𝑟𝑖𝑣𝑒𝑛        𝐴
                                             160 −163
                                         =                x 40    ✓
                                               120
                                              3      8
                                         =-4 x 8                  ✓

                                         = - 24/32
                The driver gear has 24 teeth.
                The driven gear has 32 teeth.                 ✓                            (4)

       6.5.3    The direction of motion is anti-clockwise ✓
                The crank handle will turn the opposite direction as index plate (-) ✓     (2)

 6.6   Dove tail calculations

       6.6.1    Calculate Y and X
                Y = 180 – 2(DE)
                X = 180 – 2(DE) + 2(AC) + 2 (Radius)              ✓
                Calculating AC:

                Calculating BE

                Calculating Y
                Y = 180 – 2(DE)
                  = 180 – 2(18,48) ✓
                  = 143,04 mm      ✓
                X = 180 – 2(DE) + 2(AC) + 2 (Radius)
                  = 143,04 + 2 (21,65) + 2 (12,5) ✓
                  = 211,34 mm                     ✓                                       (11)
                                                                                          [28]

Copyright reserved                                                            Please turn over

### Page 8

8               MECHANICAL TECHNOLOGY (FITTING AND MACHINING)            (EC/SEPTEMBER 2023)

 QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

 7.1   Brinell Hardness test procedure
       • The desired load in kilograms is selected on the dial by adjusting the air
          regulator. ✓
       • The specimen is placed on the anvil. Ensure that the specimen is clean
          and free from burrs. It should be smooth enough so that an accurate
          measurement can be taken of the impression. ✓
       • The specimen is raised to be in contact with Brinell ball by turning the
          hand wheel. ✓
       • The load is then applied by pulling out the plunger control. Maintain the
          load for 30 seconds for non-ferrous metals and 14 seconds for steel. ✓
       • Remove the specimen from the tester and measure the diameter of the
          impression. ✓                                                                 (5)

 7.2   The THREE ways that hardness is measured:
       • Resistance to penetration   ✓
       • Elastic hardness ✓
       • Resistance to abrasion ✓                                                       (3)

 7.3   Study Engineering Apparatus

       7.3.1    Rockwell hardness tester ✓                                              (1)

       7.3.2    A – Hardness Indicator   ✓
                B – Platform             ✓
                C – Height Adjuster      ✓
                D – Activating knob      ✓                                              (4)
                                                                                       [13]

Copyright reserved                                                           Please turn over

### Page 9

(EC/SEPTEMBER 2023)    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                 9

 QUESTION 8: FORCES (SPECIFIC)

 8.1 Resultant Force Calculations:

       8.1.1    ∑Xcom = 4,7 – 3,1 cos 50 – 1,5 cos 40 ✓✓
                      = 3,856 kN ✓                                                 (3)

       8.1.2    ∑Ycom = 2,1 + 1,5 sin40 – 3,1 sin 50 ✓✓
                      = 0,69 kN     ✓                                              (3)

       8.1.3    R     = √(𝑋 2 + 𝑌²)
                R     = √[(3,856)2 + (0,69)2 ]
                R     = 3,92 kN     ✓
                Tan θ = y/x        ✓
                Tan Θ = 0,69/3,856
                    Θ = 10,145°    ✓

                Equilibrant = Resultant BUT IN THE OPPOSITE DIRECTION

                Equilibrant = 3,92 kN at 190,145º ✓                                (4)

Copyright reserved                                                     Please turn over

### Page 10

10              MECHANICAL TECHNOLOGY (FITTING AND MACHINING)   (EC/SEPTEMBER 2023)

 8.2   Moments

       Converting the UDL to Point Load
       350 x 6,7 = 2345 kN @ 3,35 m from Left hand end ✓

       Calculation the Reactions by Taking moments:

                                                                               (7)

 8.3   Stress and Strain Calculations

       8.3.1    Calculate the diameter of the pin.
                Dia = ? F = 100 kN; E= 210 PGa:

                                                                               (6)

Copyright reserved                                                  Please turn over

### Page 11

(EC/SEPTEMBER 2023)    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                11

       8.3.2    Strain in the pin

                                                                                   (3)

       8.3.3    Change in length

                                                                                   (3)

       8.3.4    Compressive Stress. ✓                                              (1)

 8.4   Stress/Strain diagram labels

       A – Limit of Proportionality ✓
       B – Elastic limit: ✓                                                        (2)
       C – Yield Point ✓                                                           (1)
                                                                                  [33]

Copyright reserved                                                     Please turn over

### Page 12

12              MECHANICAL TECHNOLOGY (FITTING AND MACHINING)          (EC/SEPTEMBER 2023)

 QUESTION 9: MAINTENANCE

 9.1 Properties of nylon:
     • Needs no lubrication         ✓
     • Can withstand a lot of shock ✓
     • No maintenance               ✓
     • Light in weight              ✓
     • Easy to machine              ✓                          (Any 3 x 1)             (3)

 9.2 Reasons for using cutting fluid when working on the centre lathe
     • It prolongs the life of a cutting tool. ✓
     • It prevents the shavings or metal chips from sticking and fusing to the
        cutting tool. ✓
     • It will carry away the heat generated by the turning process.
     • It flushes away shavings/metal chips. ✓
     • It improves the quality of the finish of the turned surface.    (Any 2 x 1)     (2)

 9.3 Consequences for failure to maintain equipment.
     • Risk of injury
     • Financial loss due to long breakdown
     • Loss of production time                                                         (2)

 9.4 Reasons for using of carbon fibre
     • It light in weight. ✓
     • It is tougher and stronger.   ✓
     • It can be bent to any shape when heated above 150 ºC. ✓         (Any 2 x 1)     (2)

 9.5 TWO property and TWO uses of PVC

       COMPOSITE PROPERTY/CHARACTERISTICS                          USES
       PVC       - Resistant to water, grease, heat    - Electrical cables,
                   and corrosion ✓                       artificial leather, cling
                 - Flexible, rubberlike, tough and       wrap, credit and phone
                   easy to bond ✓              (Any 2)   cards ✓✓          (Any 2)     (4)

 9.6 Preventative Maintenance
     • Inspection ✓
     • Measuring ✓
     • Cleaning ✓
     • Lubricating ✓
     • Adjusting and Replacement of parts ✓                            (Any 3 x 1)      (3)
                                                                                       [18]

Copyright reserved                                                           Please turn over

### Page 13

(EC/SEPTEMBER 2023)         MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                   13

 QUESTION 10: JOINING METHODS (SPECIFIC)

 10.1   Square Thread Calculations:
        T = 48 mm; m = 3

        10.1.1        PCD = T x m
                          = 48 x 3 = 144 mm ✓✓                                             (2)

        10.1.2        Add = Module = 3 mm ✓                                                (1)

        10.1.3        Clearance    = 0,157 x 3
                                   = 0,471 mm ✓✓                                           (2)

        10.1.4        Ded    = 1,157 x 3
                             = 3,471 mm ✓✓                                                 (2)

        10.1.5        OD     = PCD + 2 x 3
                             = 150 mm ✓✓                                                   (2)

        10.1.6        Circular Pitch
                      =πxm
                      = π x 3 = 9,424 mm         ✓                                         (1)

 10.2   Left-hand square screw thread

        A – Leading Angle                    ✓
        B – Following or Trailing Angle      ✓
        C – Clearance                        ✓
        D – Helix angle                      ✓                                             (4)

 10.3   A multi-start thread allows for a faster travel or movement and is more
        efficient at it lose less power to friction compare to single start thread. ✓✓     (2)

 10.4   International Standards Organization ✓✓                                            (2)
                                                                                          [18]

Copyright reserved                                                             Please turn over

### Page 14

14               MECHANICAL TECHNOLOGY (FITTING AND MACHINING)    (EC/SEPTEMBER 2023)

 QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)

 11.1   Pressure is the action of putting force onto a body. ✓✓                  (2)

 11.2   Hydraulic system calculations

        11.2.1       Calculate the diameter of Piston A

                                                                                 (9)

        11.2.2       Calculate the pressure exerted on Piston A

                                                                                 (2)

Copyright reserved                                                    Please turn over

### Page 15

(EC/SEPTEMBER 2023)      MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                 15

        11.2.3        Calculate the force exerted on Piston B

                                                                                      (4)

 11.3   Hydraulics refers to the transmission and control of forces and movement
        by means of fluid. Fluid (generally oil) is used to transmit energy. ✓✓       (2)

 11.4   Belt Drive Calculations
        Nmotor x Dmotor = Nblade x Dblade

          130 x 1205 = 385 x Dblade          ✓

        Dblade = 406,883 pm ✓                                                         (2)

 11.5   Pneumatic symbols

        11.5.1 Cylinder

                                                     ✓                                (1)
        11.5.2 Accumulator

                                                 ✓                                    (1)
        11.5.3 Electric Motor

                                                 ✓                                    (1)

Copyright reserved                                                        Please turn over

### Page 16

16               MECHANICAL TECHNOLOGY (FITTING AND MACHINING)   (EC/SEPTEMBER 2023)

 11.6   Gear-Drive system calculations:
        Data:

        11.6.1       Rotational frequency of the output shaft:

                                                                                (3)

        11.6.2       Velocity ratio

                                                                                (2)

        11.6.3       Driven will rotate Clockwise: ✓                            (1)
                                                                               [28]

                                                                   TOTAL:      200

Copyright reserved                                                   Please turn over

## Related documents

- [MECH TECH GR12 QP SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept2023-welding-english/49e9215c-dc78-48c3-a526-4baaf59158d8) — Mechanical Technology · QP · 2023 · Eng
- [MECH TECH GR12 MEMO SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept-2020-auto-english/9066fed3-db75-4436-9ea3-0a432f99cc0b) — Mechanical Technology · Memo · 2020 · Eng
- [MECH TECH GR12 QP SEPT 2020 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87) — Mechanical Technology · QP · 2020 · Eng
- [MECH TECH GR12 QP SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162) — Mechanical Technology · QP · 2020 · Eng
- [MECHANICAL TECH (Auto) MEMO SEPT 2018 English](https://www.hlayiso.com/library/mechanical-tech-auto-memo-sept-2018-english/b985e4dd-9a08-4ec2-a07b-64edd6f727ea) — Mechanical Technology · Memo · 2018 · Eng
- [MECHANICAL TECH (Welding) GR12 MEMO SEPT 2018 English](https://www.hlayiso.com/library/mechanical-tech-welding-gr12-memo-sept-2018-english/1b0b4dd6-b53e-485d-9068-6f378eb8c9f3) — Mechanical Technology · Memo · 2018 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — QP · 2024 · Eng
- [Mechanical Technology May-June 2023 (Welding & Metalwork) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-afr/7d638feb-7218-4b3c-9f4c-ce95803d6e4f) — QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-eng/1523a16f-2012-4f13-a922-86cbb5900666) — QP · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
