# Mechanical Technology Grade 12 Eastern Cape Mock 2023 QP > Grade 12 Mechanical Technology question paper from the Eastern Cape Mock Exam 2023 (English), 23 pages. Read online or download the free PDF. - Page: https://www.hlayiso.com/library/mec-tech-gr12-qp-sept2023-fitting-english/a7d11fc8-df6c-4132-bba7-58812acf70a0 - Updated: 2026-09-27 - Subject: Mechanical Technology - Grade: Grade 12 - Language: English - Document type: Question paper - Year: 2023 - Exam period: Eastern Cape Mock Exam - Curriculum: CAPS - Pages: 23 Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 Eastern Cape Mock 2023 QP](https://www.hlayiso.com/library/mec-tech-gr12-qp-sept2023-fitting-english/a7d11fc8-df6c-4132-bba7-58812acf70a0) ## About this document Mechanical Technology · Grade 12 · Eastern Cape Mock Exam · 2023 · English. Question paper, 23 pages. Read online or download the PDF. Read it free online on the page above; download the PDF from there. ## Document text Text extracted from the PDF. Layout, diagrams and tables may not survive extraction. ### Page 1 NATIONAL SENIOR CERTIFICATE GRADE 12 SEPTEMBER 2023 MECHANICAL TECHNOLOGY: FITTING AND MACHINING MARKS: 200 TIME: 3 hours This question paper consists of pages 23, including a 4-page formula sheet. ### Page 2 2 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) INSTRUCTIONS AND INFORMATION 1. Write your NAME on the ANSWER BOOK. 2. Read ALL the questions carefully. 3. Answer ALL the questions. 4. Number the answers correctly according to the numbering system used in this question paper. 5. Start EACH question on a NEW page. 6. Show ALL calculations and units. Round off final answers to TWO decimal places. 7. You may use a non-programmable scientific calculator and drawing instruments. 8. The value of gravitational force should be taken as 10 m/s-2. 9. All dimensions are in millimeters, unless stated otherwise in the question. 10. A formula sheet is attached to the question paper. 11. Write neatly and legibly. 12. Use the criteria below to assist you in managing your time management. QUESTION CONTENT MARKS TIME in minutes GENERIC 1 Multiple-choice questions 6 6 2 Safety 10 10 3 Materials 14 14 SPECIFIC 4 Multiple-choice questions 14 10 5 Terminology (Lathe and Milling) 18 20 6 Terminology (Indexing) 28 25 7 Tools and Equipment 13 10 8 Forces 33 33 9 Maintenance 18 12 10 Joining Methods 18 12 11 Systems and Control (Drive systems) 28 28 TOTAL 200 180 Copyright reserved Please turn over ### Page 3 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 3 QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC) (COMPULSORY) Various options are provided as possible answers to the following questions. Choose the correct answer and write only the letter (A–D) next to the question numbers (1.1 to 1.6) in the ANSWER BOOK, for example 1.7 A. 1.1 Which of the following options below describes the Labour Relation Act (LRA No. 66 of 1995) in South Africa that protect the people living with HIV/Aids? A All employers must ensure that the workplace is safe, and that employees are not at risk of becoming infected with HIV at work. B Elaborates how everybody has the right to fair labour practice. C Employer cannot simply dismiss an employee who is infected with HIV. D Promotes non-discrimination in the workplace. (1) 1.2 Examination procedure is one of the processes undertaken to determine the type of first aid measures to be administered to an employee who is involved in an accident in a workplace. Identify the option below that best describe this process. A Environmental observation B Visible signs and symptoms C Indicators to diagnosis D All of the above (1) 1.3 The following safety precautions must be followed when handling gas bottles: A All cylinders must be kept in horizontal position B Use completely insulated electrode holders C Never stack cylinders on top of each another D The colour code of an oxygen cylinder is green (1) 1.4 Which ONE of the heat treatment process is used to remove internal strain and brittleness caused by hardening? A Annealing B Case-hardening C Tempering D Normalising (1) 1.5 Which of the following test is used to determine the carbon content of steel? A Sound test B Bend test C Filing test D All of the above (1) Copyright reserved Please turn over ### Page 4 4 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) 1.6 Why is it important to clamp a small workpiece securely before drilling operation can be carried out? A To reduce friction B To prevent the drill bit from breaking as well as preventing accident C To keep the cutting tool and workpiece cool D All of the above (1) [6] Copyright reserved Please turn over ### Page 5 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 5 QUESTION 2: SAFETY (GENERIC) 2.1 Give THREE safety precautions you must take into consideration before arc welding operation can commence. (3) 2.2 State TWO safety precautions that you must adhere to when you are operating a pedestal drilling machine to drill a hole on a solid square bar. (2) 2.3 What is the maximum thickness of a steel plate that a manual guillotine can accommodate if cutting with it? (1) 2.4 Give TWO advantages of each of the following workshop layouts: 2.4.1 Product layout of machines (2) 2.4.2 Process layout of machines (2) [10] Copyright reserved Please turn over ### Page 6 6 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) QUESTION 3: MATERIALS (GENERIC) 3.1 State the TWO main purpose of case hardening mild steel. (2) 3.2 Why can high carbon steel not be used for case hardening? (1) 3.3 State THREE factors that determine the hardness of steel during heat treatments of metal. (3) 3.4 List THREE types of quenching mediums. (3) 3.5 What is the purpose of the colour coding marked on engineering materials? (1) 3.6 State the type of test that can be used to obtain the following properties of metals: 3.6.1 Hardness (1) 3.6.2 Carbon content (1) 3.6.3 Ductility (1) 3.7 List the machine that is used for a spark test. (1) [14] Copyright reserved Please turn over ### Page 7 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 7 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC) Various options are provided as possible answers to the following questions. Choose the correct answer and write only the letter (A–D) next to the question numbers (4.1 to 4.14) in the ANSWER BOOK, for example 4.15 A. 4.1 FIGURE 4.1 below shows a Brinell hardness tester to determine the hardness of a test piece. FIGURE 4.1 Identify part X. A Bearing B Diameter of indentation C Motion D Brinell Ball (1) 4.2 Identify the type of milling operation shown in FIGURE 4.2. FIGURE 4.2 A Plain straight-tooth cutter B Straight-tooth side-milling cutter C Down-cutting D Slab Cutting (1) 4.3 Which ONE of the following is a lathe component? A Grinding wheel B Feed shaft C Pressure gauge D Feed lever (1) Copyright reserved Please turn over ### Page 8 8 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) 4.4 What does the abbreviation CNC stands for? A Computer Numerical Control B New Control Coding C Company Numbers Control D None of the above (1) 4.5 In a tensile test … A a test piece is loaded to destruction. B beams are used to determine the structure of a weld. C a hammer is used to break the test material. D liquid dye is used to detect weld flaws. (1) 4.6 The main reason for performing a hardness test on engineering materials is to determine the … A elasticity of the material. B resistance of the material against denting C corrosion of the material. D fluidity of the metal (1) 4.7 What does the point E denote in the stress/strain diagram in FIGURE 4.7? FIGURE 4.7 A Limit of proportionality B Elasticity limit C Maximum stress D Break stress (1) 4.8 Unless stated otherwise, what clearance angle is normally used to calculate the leading and following tool angles of a square thread cutting tool? A 90° B 3° C 60° D 45° (1) Copyright reserved Please turn over ### Page 9 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 9 4.9 What will be the drill size for a M12 x 1,5 screw thread? A 13,5 mm B 1,5 mm C 12 mm D 10,5 mm (1) 4.10 A work piece must have 13 gear teeth machined on its circumference. What type of indexing would be performed on this gear-blank? A Angular indexing B Simple indexing C Rapid indexing D New indexing (1) 4.11 If the module of a spur gear is 2,5. What will the addendum be? A 6 mm B 3 mm C 2,5 mm D 9 mm (1) 4.12 Identify the drilling operation in FIGURE 4.12. FIGURE 4.12 A Counter-sinking B Tapping C Turning D Milling (1) 4.13 There are different types of machine processes in manufacturing. Which process would be used to enlarge holes to exact tolerances? A Tapping B Boring C Slotting D Reaming (1) Copyright reserved Please turn over ### Page 10 10 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) 4.14 Identify the symbol, shown in FIGURE 4.14 below, which relates to a pneumatic system. FIGURE 4.14 A Valve B Filter C Compressor D Motor (1) [14] Copyright reserved Please turn over ### Page 11 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 11 QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHICE) (SPECIFIC) 5.1 Calculate the cutting depth of a metric V-screw thread with a pitch of 2,5 mm using the compound slide method. (3) 5.2 Name TWO methods used to cut screw threads using a centre lathe. (2) 5.3 A circular shaft with an outside diameter of 100 mm must be machined with a two-start square thread of 12 mm pitch. Calculate the following: 5.3.1 The lead of the thread (2) 5.3.2 The mean diameter of the thread (2) 5.3.3 The helix angle of the thread (2) 5.4 FIGURE 5.4 below shows the components around the cutting area of a milling machine. Answer the questions that follow. FIGURE 5.4 5.4.1 Identify the type of milling in FIGURE 5.4. (1) 5.4.2 Label parts A–F. (6) [18] Copyright reserved Please turn over ### Page 12 12 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC) 6.1 State TWO advantages of gang milling. (2) 6.2 State ONE use of the following milling cutters. 6.2.1 T-slot milling cutter (1) 6.2.2 End mill cutter (1) 6.2.3 Slitting saw (1) 6.3 Define the term module as applied to gears. (1) 6.4 Explain, by using a neat labelled sketch, how up-cut milling must be done. (2) 6.5 Sizwe is a machinist and he is required to mill 163 teeth on a spur gear. The dividing head ratio is 40 : 1. (HINT : Use N = 160 divisions for the simple indexing.) 6.5.1 Calculate the indexing required. (3) 6.5.2 Calculate the change gears required for the dividing head. (4) 6.5.3 What is the meaning of the positive (+) sign and the negative (-) sign for the change of gears? (2) 6.6 FIGURE 6.6 show two precision rollers placed in an external dovetail. Use the given information to answer the question the follow. FIGURE 6.6 6.6.1 Calculate distance Y and X. (11) [28] Copyright reserved Please turn over ### Page 13 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 13 QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC) 7.1 Explain the procedure/steps of setting up the Brinell hardness tester and performing the test. (5) 7.2 Name the THREE ways that hardness is measured. (3) 7.3 Study the diagram shown in FIGURE 7.3 below and answer the questions that follows. FIGURE 7.3 7.3.1 What is the name of the engineering apparatus in FIGURE 7.3? (1) 7.3.2 Label parts A–D. (4) [13] Copyright reserved Please turn over ### Page 14 14 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) QUESTION 8: FORCES (SPECIFIC) 8.1 FIGURE 8.1 below shows a system of forces with four concurrent applied forces. FIGURE 8.1 Calculate the: 8.1.1 Sum of the horizontal components in magnitude and direction (3) 8.1.2 Sum of the vertical components in magnitude and direction (3) 8.1.3 Magnitude and direction of the resultant force and its equilibrant (4) 8.2 FIGURE 8.2 below shows a beam with two vertical applied point loads of 1 400 N and another 1 600 N and also a 350 N/m uniformly distributed load for a total span of 6,7 m. FIGURE 8.2 Calculate the magnitude of reactions RA and RB. (7) Copyright reserved Please turn over ### Page 15 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 15 8.3 Sakhi was instructed to use a mild steel pin to remove a bush from the yoke using a hydraulic press. The drawing of the pin, shown in FIGURE 8.3, indicates a load of 100 kN that causes a stress of 204 MPa. FIGURE 8.3 8.3.1 Calculate the diameter of the pin in millimetres. (6) 8.3.2 Calculate the strain induced in the pin if Young’s modulus of elasticity is 210 GPa. (3) 8.3.3 Calculate the change in the length of the pin if the original length is 110 mm. (3) 8.3.4 What type of stress is induced in the pin? (1) 8.4 FIGURE 8.4 shows a stress-strain diagram. FIGURE 8.4 Label parts A, B and C. (3) [33] Copyright reserved Please turn over ### Page 16 16 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) QUESTION 9: MAINTENANCE (SPECIFIC) Solid nylon is widely used for engineering purposes. FIGURE 9.1 shows gear wheels made from solid nylon: Nylon gear wheels FIGURE 9.1 9.1 Name THREE properties which make nylon particularly suitable for the manufacturing of gears. (3) 9.2 Why is it essential to use a cutting fluid on a milling machine or centre lathe. State TWO reasons. (2) 9.3 What are the possible consequences for failure to do maintenance? (2) 9.4 Give TWO reasons for using carbon fibre in the manufacture of bicycle frames. (4) 9.5 In tabulated form compare TWO characteristics and TWO uses of PVC. (4) 9.6 Name THREE routine aspects when preventative maintenance is conducted. (3) [18] Copyright reserved Please turn over ### Page 17 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 17 QUESTION 10: JOINING METHODS (SPECIFIC) 10.1 A spur gear has 48 teeth and a module of 3. Determine, by means of calculations, the following: 10.1.1 The pitch-circle diameter (2) 10.1.2 The addendum (1) 10.1.3 The clearance (2) 10.1.4 The dedendum (2) 10.1.5 The outside diameter of the gear (2) 10.1.6 Circular pitch (1) Study FIGURE 10.2 below and answer the questions that follow. FIGURE10.2 10.2 Label parts A–D. (4) 10.3 Why would a multi-start thread be preferred mostly to a single start thread? (2) 10.4 What does the abbreviation ISO stands for? (2) [18] Copyright reserved Please turn over ### Page 18 18 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) QUESTION 11: SYSTEMS AND CONTROL (SPECIFIC) 11.1 Define the term pressure. (1) 11.2 A hydraulic system is used to lift a lathe. The specifications of the system are presented diagrammatically in FIGURE 11.2. FIGURE 11.2 Calculate the following: 11.2.1 The diameter of piston A (HINT: VA = VB) (9) 11.2.2 The pressure exerted on piston A (2) 11.2.3 The force exerted on piston B (4) 11.3 Define what is meant by hydraulics. (1) 11.4 A power saw’s motor has a pulley, 130 mm in diameter, that turns at 1 205 rpm. The speed at which the driven pulley drives the saw blades is 385 rpm. Calculate the diameter of the driven pulley. (2) 11.5 Make neat, freehand sketches of the ISO symbols representing the following pneumatic components: 11.5.1 Cylinder (1) 11.5.2 Accumulator (1) 11.5.3 Electric motor (1) Copyright reserved Please turn over ### Page 19 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 19 11.6 FIGURE 11.6 below shows a gear-drive system. A driver gear on the shaft of an electric motor has 20 teeth and meshes with a gear on a counter shaft with 36 teeth. On this counter shaft is another driver gear with 18 teeth that meshes with a gear with 46 teeth on a second counter shaft. The second counter shaft has a driver gear with 42 teeth which drives a gear with 80 teeth on the output shaft. FIGURE 11.6 Calculate the: 11.6.1 Rotation frequency of the output shaft on the electric motor if the electric motor shaft rotates at 160 r/min (3) 11.6.2 Velocity ratio between the input and output shaft (2) 11.6.3 Direction in which the driven shaft will rotate if the driver gear rotates anti-clockwise (1) [28] TOTAL: 200 Copyright reserved Please turn over ### Page 20 20 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) FORMULA SHEET FOR MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 1. BELT DRIVES DN πDN Belt speed = or v= 60 60 Diameter of driven pulley Speed ratio = Diameter of driver pulley N 1 D1 = N 2 D 2 2 π NT Power ( P ) = 60 T1 Ratio of tight side to slack side = T2 (T1 − T2 ) π D N Power = where T1 = force in the tight side 60 T2 = force in slack side T1 − T2 = effective force (Te ) 2. STRESS AND STRAIN Force F Stress = or ( σ = ) Area A change in length ( ΔL ) Strain ( ε ) = original length ( L ) stress σ Young' s mod ulus ( E ) = or ( ) strain ε π d2 A shaft = 4 π (D 2 − d 2 ) A pipe = 4 Break stress Safety factor = Safe working stress Copyright reserved Please turn over ### Page 21 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 21 3. HYDRAULICS Force ( F ) Pressure ( P ) = Area ( A ) Volume = Cross -sectional area  stroke length 4. KEYS AND KEYWAYS Diameter of shaft Width of key = 4 Diameter of shaft Thickness of key = 6 Length of key = 1,5  Diameter of shaft Standard taper for taper key : 1 in 100 or 1 : 100 5. GEAR DRIVES 2NT Power ( P ) = 60 N 1T1 = N 2 T2 Product of the number of teeth on driven gears Gear ratio = Product of the number of teeth on driving gears N input Product of the number of teeth on driven gears = N output Product of the number of teeth on driving gears Torque = force  radius Torque transmitte d = gear ratio  input torque Pitch -circle diameter ( PCD ) Module ( m ) = Number of teeth ( T ) Copyright reserved Please turn over ### Page 22 22 MECHANICAL TECHNOLOGY (FITTING AND MACHINING) (EC/SEPTEMBER 2023) circular pitch ( CP )  number of teeth ( T ) Pitch -circle diameter ( PCD ) = π Outside diameter ( OD ) = PCD + 2 module Addendum ( a ) = module ( m ) Dedendum ( b ) = 1,157 m or Dedendum ( b ) = 1,25 m Cutting depth ( h ) = 2,157 m or Cutting depth ( h ) = 2,25 m Clearance ( c ) = 0,157 m or Clearance ( c ) = 0,25 m Circular pitch ( CP ) = m  π Tm  90   Add c = m + 1− cos  2  T  90  90  t c = Tmsin or t c = PCDsin T T Copyright reserved Please turn over ### Page 23 (EC/SEPTEMBER 2023) MECHANICAL TECHNOLOGY (FITTING AND MACHINING) 23 6. SCREW THREADS Pitch diameter = Outside diameter − ½pitch Pitch circumfere nce = π  pitch diameter Lead = pitch  number of starts Height of screw thread = 0,866  p where p = pitch of the screw thread Depth of screw thread = 0,613  p where p = pitch of the screw thread length Number of turns = lead lead Helix angle : tan θ = pitch diameter Leading tool angle = 90  − (helix + clearance angle ) Following tool angle = 90  + (helix − clearance angle ) 7. CINCINNATI DIVIDING HEAD TABLE FOR THE MILLING MACHINE Hole Circles Side 1 24 25 28 30 34 37 38 39 41 42 43 Side 2 46 47 49 51 53 54 57 58 59 62 66 Change Gears 24 x 2 28 32 40 44 48 56 64 72 86 100 40 Simple indexing = ( where n = number of divisions) n n Angular Indexing = 9 Dr 40 Dr ( A − n ) 40 Change gears: = (A − n )  or =  Dn A Dn A 1 (where A = chosen divisions ) (where n = given divisions ) Copyright reserved Please turn over ## Related documents - [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Mechanical Technology · Memo · 2023 · Eng - [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Mechanical Technology · Memo · 2023 · Eng - [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Mechanical Technology · Memo · 2023 · Eng - [MECH TECH GR12 QP SEPT 2020 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87) — Mechanical Technology · QP · 2020 · Eng - [MECH TECH GR12 QP SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162) — Mechanical Technology · QP · 2020 · Eng - [MECH TECH GR12 MEMO SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept-2020-auto-english/9066fed3-db75-4436-9ea3-0a432f99cc0b) — Mechanical Technology · Memo · 2020 · Eng ## More from Grade 12 Mechanical Technology - [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP - [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng - [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng - [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — QP · 2023 · Afr - [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — QP · 2023 · Afr - [Mechanical Technology May-June 2023 (Welding & Metalwork) Eng](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-eng/c6bfa7b8-3601-4a11-9be4-55ee65e4011f) — QP · 2023 · Eng ## Collection - [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers) --- Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.