# Mechanical Technology Grade 12 Eastern Cape Mock 2025 Memo

> Grade 12 Mechanical Technology memorandum from the Eastern Cape Mock Exam 2025 (English), 21 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mech-tech-fitting-memo-gr12-sept-2025-eng-watermark/9b5fdaa9-9200-4800-9144-bc92c5f991d3
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2025
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 21

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 Eastern Cape Mock 2025 Memo](https://www.hlayiso.com/library/mech-tech-fitting-memo-gr12-sept-2025-eng-watermark/9b5fdaa9-9200-4800-9144-bc92c5f991d3)

## About this document

Mechanical Technology · Grade 12 · Eastern Cape Mock Exam · 2025. Memorandum, 21 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

NATIONAL
                   SENIOR CERTIFICATE

                           GRADE 12

                    SEPTEMBER 2025

               MECHANICAL TECHNOLOGY:
                FITTING AND MACHINING
                  MARKING GUIDELINE

MARKS:   200

                 This marking guideline consists of 21 pages.

### Page 2

2            MECHANICAL TECHNOLOGY (FITTING AND MACHINING)             (EC/SEPTEMBER 2025)

 SECTION A: COMPULSORY
 QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)
 1.1 A                                                                                (1)
 1.2 C                                                                                (1)
 1.3 C                                                                                (1)
 1.4 B                                                                                (1)
 1.5 A                                                                                (1)
 1.6 D                                                                                (1)
                                                                           (6 X 1)     (6)

 QUESTION 2: SAFETY (GENERIC)
 2.1 Safety precautions
     • See that all guards are in place. 
     • Make sure that no oil, grease, or obstacles are around the machine. 
     • Select the right blade for the material to be cut. 
     • Do not adjust guides while the machine is running. 
     • All materials must be clamped properly before cutting is started. 
     • Long pieces of material must be supported at the end. 
     • Always stop machine when you leave it unattended.             (Any 2 x 1)      (2)
 2.2 Responsibilities of the employees
     • Pay attention to their own and other people’s health and safety. 
     • Co-operate with the employer regarding the OHS Act. 
     • Carry out a lawful order given to them. 
     • Report any situation that is unsafe or unhealthy. 
     • Report all incidents and accidents. 
     • Not to interfere with any safety equipment or misuse such equipment
     • Obey all safety rules.                                        (Any 2 x 1)      (2)
 2.3 Bench grinder
     • Use safety goggles at all times when grinding metal. 
     • Do not adjust the tool rest while the wheel is in motion. 
     • Do not force the workpiece onto or bump it against the emery wheel.
     • Keep fingers away from revolving wheel, especially when grinding small
       pieces. 
     • Grind only on the front surface and never on the sides of an emery
       wheel.                                                       (Any 2 x 1)       (2)

Copyright reserved                                                         Please turn over

### Page 3

(EC/SEPTEMBER 2025)      MECHANICAL TECHNOLOGY (FITTING AND MACHINING)               3

 2.4 Advantages of product layout
     • Handling of material is limited to a minimum. 
     • Time period of manufacturing cycle is less. 
     • Production control is almost automatic. 
     • Control over operations is easier. 
     • Greater use of unskilled labor is possible. 
     • Less total inspection is required. 
     • Less total floor space is needed per unit of production. 
                                                                    (Any 2 x 1)     (2)

 2.5 Categories of OHS
     • Actions 
     • Conditions                                                                 (2)
                                                                                  [10]

Copyright reserved                                                     Please turn over

### Page 4

4            MECHANICAL TECHNOLOGY (FITTING AND MACHINING)             (EC/SEPTEMBER 2025)

 QUESTION 3: MATERIALS (GENERIC)

 3.1 Testing materials
     • Sound test 
     • Bending test 
     • Filling test 
     • Machining test
     • Hardness test
     • Spark test                                                    (Any 3 x 1)        (3)

 3.2 Carbon groups
     • Low carbon steel  0,15–0,3% 
     • Medium carbon steel  0,3–0,75% 
     • High carbon steel  0,75–1,7%                                                   (6)

 3.3 Purpose of normalizing
     • To relieve the internal stresses produced by machining, forging or
       welding.                                                                        (2)

 3.4 Tempering process for steel
     • Heat the steel to a temperature below the critical temperature. 
     • Soak it at that temperature for a period. 
     • Quench / cool in an appropriate quenching agent. (water, brine, or oil)         (3)
                                                                                       [14]

Copyright reserved                                                           Please turn over

### Page 5

(EC/SEPTEMBER 2025)   MECHANICAL TECHNOLOGY (FITTING AND MACHINING)            5

 QUESTION 4: MULTIPLE-CHOICE QUESTION (SPECIFIC)

 4.1    C

 4.2    C

 4.3    A

 4.4    A

 4.5    B

 4.6    D

 4.7    A

 4.8    B

 4.9    B

 4.10   A

 4.11   D

 4.12   C

 4.13   D

 4.14   B                                                                  [14]

Copyright reserved                                               Please turn over

### Page 6

6            MECHANICAL TECHNOLOGY (FITTING AND MACHINING)               (EC/SEPTEMBER 2025)

 QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)

 5.1   Tailstock set over

               𝜃     𝑋
           Tan 2 = 320 

           X = Tan 3,5° x 320 

            = 19,57 mm                                                                  (3)

 5.2   Keyway

       5.2.1    Parallel key OR Pratt and Whitney key OR feather key                    (1)

       5.2.2             Length         = 1,5 x D
                                         126
                         Diameter       = 1,5 

                                        = 84 mm                                         (2)

       5.2.3             Thickness      =6
                                          𝐷

                                         84
                                        = 6    

                                        = 14 mm                                         (2)

       5.2.4             Width = 4
                                    𝐷

                                         84
                                        = 4    

                                        = 21 mm                                         (2)

 5.3   Milling processes
       Up-cut milling advantages

       •   Heavier cuts can be taken 
       •   Hard steels can be cut.
       •   Life of a milling cutter is extended.
       •   A coarse feed can be used.
       •   Strain on the cutter and arbor will be less.
       •   Heavier cuts can be taken                                     (Any 1 x 1)     (1)

Copyright reserved                                                            Please turn over

### Page 7

(EC/SEPTEMBER 2025)       MECHANICAL TECHNOLOGY (FITTING AND MACHINING)            7

       Down-cut milling advantages
       • Deeper cuts can be taken 
       • A finer finish is obtained
       • Less vibration is experienced                            (Any 1 x 1)     (2)

 5.4 Difference between gang milling and straddle milling.

       Correct drawing    2 marks each
       Labels             1 mark each                                            (6)
                                                                                [18]

Copyright reserved                                                   Please turn over

### Page 8

8              MECHANICAL TECHNOLOGY (FITTING AND MACHINING)      (EC/SEPTEMBER 2025)

QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)
6.1    Gear terminology
       6.1.1     Dedendum

                                                                                  (2)
       6.1.2     Pitch circle diameter.

                 PCD = circular pitch (CP) x number of teeth(T)
                                          π
                    = (m x π) x T
                            π
                    = 7,85 x 25
                           π
                    = 62,5 mm

                                                  OR

                                                                                  (2)
       6.1.3     Outside diameter

                                                                                  (2)

       6.1.4     Circular pitch

                                                                                  (2)

Copyright reserved                                                    Please turn over

### Page 9

(EC/SEPTEMBER 2025)               MECHANICAL TECHNOLOGY (FITTING AND MACHINING)            9

6.2    Spur gear cutting

       6.2.1    Simple indexing
                                     40
                Indexing           = 𝐴 

                                      40
                                   = 100 

                                     2     5
                                   =5×5

                                     10
                                   = 25 

                Indexing is 10 holes in 25-hole circle 
                                    OR
                Indexing is 12 holes in 30-hole circle                                    (4)

       6.2.2    Change gears
                𝐷𝑟𝑖𝑣𝑒𝑟       𝐴−𝑁     40
                         =         × 1         
                𝐷𝑟𝑖𝑣𝑒𝑛        𝐴

                                                   100−97     40
                                               =             × 1 
                                                       100

                                                   120
                                               =         
                                                   100

                                                   6     8
                                               =5×8 

                                                   48
                                               = 40 

                Driver has 48 teeth
                Driven has 40 teeth                                                       (5)

Copyright reserved                                                           Please turn over

### Page 10

10           MECHANICAL TECHNOLOGY (FITTING AND MACHINING)               (EC/SEPTEMBER 2025)

 6.3   Dovetail calculations
       Calculate distance “x” between rollers:
               X         = 120−2(DE)+2(AC)+2 (r)

               Y     = 120 − 2 (DE)

       Calculating DE

       Calculating AC

       Calculating Y

                         Y     = 120 − 2 (DE)
                               = 120 − 2 (18,48) 
                               = 83,04 mm 

       Calculating X

                     X        = 120 − 2(DE) + 2(AC) + 2 (r) 
                              = 120 − 2(18,48) + 2(21,65) + 2 (12,5) 
                              = 83,04 + 43,3 + 25
                              = 151,34 mm                                             (11)
                                                                                       [28]

Copyright reserved                                                           Please turn over

### Page 11

(EC/SEPTEMBER 2025)        MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                    11

 QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

 7.1   Difference between hardness and toughness

       Hardness
       Material’s ability to resist deformation, abrasion, indentation, penetration or
       scratching and wear 

       Toughness
       Material’s ability to withstand shock loads without bending or cracking            (4)

 7.2   Hardness testing

       7.2.1     Brinell hardness testing                                                  (1)

       7.2.2     Label parts

                 A – Applied force 
                 B – Indenter or indenter diameter 
                 C – Indentation diameter                                                  (3)

 7.3   Screw thread micrometer reading

         Drawing         2 marks
         Correct reading 3 marks
         6 mm ✓ 0,5 mm ✓ 0,3 mm ✓                                                          (5)
                                                                                          [13]

Copyright reserved                                                             Please turn over

### Page 12

12             MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                (EC/SEPTEMBER 2025)

 QUESTION 8: FORCES (SPECIFIC)

 8.1 System of forces

       8.1.1     Sum of horizontal components

                 ∑HC = –30 cos 30 – 40 cos 45 – 60 cos 80 +70 cos 40
                     = – 25,98  – 28,28 – 10,42  + 53,62 
                     = – 11,06 N                                                          (5)

       8.1.2     Sum of vertical components

                 ∑VC = – 30 sin 30 + 40 sin 45 – 60 sin 80 – 70 sin 40
                     = – 15  + 28,28 – 59,09  – 45 
                     = – 90,81 N                                                           (5)
                                                     OR

                 Force    𝜽           Vertical components       Horizontal components
                  30    210          30 sin 210     - 15       30 cos 210    -25,98 
                  40    135          40 sin 135    28,28       40 cos 135    -28,28 
                  60    260          60 sin 260   -59,09       60 cos 260    -10,42 
                  70    320          70 sin 320     -45        70 cos 320    53,62 
                    TOTAL                Y       -90,81 N           X       -11,06N 

       8.1.3     Magnitude of the resultant
                        R2     = X2 + Y2
                               = (11,06)2 + (90,81)2 
                               = √8368,7797
                        R      = 91,48 N                                                   (2)
       8.1.4     Angle and the direction of the resultant
                                 𝑌
                        Tan 𝜽 = 𝑋

                                 𝟗𝟎,𝟖𝟏
                               = 𝟏𝟏.𝟎𝟔 

                               = tan-1 (8,21066….)

                        𝜽      = 83,10° S of W       OR      263,10°                       (2)

Copyright reserved                                                              Please turn over

### Page 13

(EC/SEPTEMBER 2025)           MECHANICAL TECHNOLOGY (FITTING AND MACHINING)           13

 8.2 Stress and Strain

       8.2.1    Diameter of the shaft

                         60 kN = 50 x 103
                         30 MPa = 30 x 106
                                          𝐹
                         𝜎        =       𝐴

                                          𝐹
                         𝐴        =       𝜎
                                              ✓

                                  =    60 x 103 ✓
                                       30 x 106
                              =       2 x 10-3 m2 

                         A        =    𝜋 r2
                                       𝐴
                         r2       =    𝜋

                                              2 × 10−3
                         𝑟        =       √              
                                                  𝜋
                                  =   25 × 10-3

                         D        =   50,46 × 10-3 m
                                  =   50,46 mm 
                                                                                      (5)

       8.2.2    Strain
                                       𝜎
                         K        =           
                                          𝜀

                                      𝜎
                         𝜀        =   𝐾

                               =       30 x 106 
                                       90 x 109
                                  =    3,33 x 10-4                                   (3)

       8.2.2    Change in length
                                       ∆𝑙
                     𝜀      =             𝐿
                                              ✓

                         ∆𝐿       =    𝜀 × L
                                  =   3,33 x 10-4 × 2
                                  =    6,67 x 10-4 m 
                                  =    0,67 mm                                        (3)

Copyright reserved                                                       Please turn over

### Page 14

14           MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                (EC/SEPTEMBER 2025)

 8.3   Moments

                                           FIGURE 8.3

       8.3.1    Uniform Distributed Load

                      5 kN/m x 4 m 
                     = 20 kN                                                             (2)

       8.3.2    Taking moments about RL

                         ∑CWM          =     ∑ACWM

                        (20 x 2) + (10 x 4) +(30 x 7) = (RR x 10)     
                         40 + 40 + 210       =     10 RR 
                              10                    10
                        RR = 29 kN                                                       (3)

       8.3.3    Taking moments about RR

                         ∑CWM          =     ∑ACWM

                        (30 x 3) + (10 x 6) +(20 x 8) = (RL x 10) 
                        90 + 60 + 160        =     10 RL 
                              10                      10
                        RL = 31 kN                                                      (3)
                                                                                        [33]

Copyright reserved                                                            Please turn over

### Page 15

(EC/SEPTEMBER 2025)        MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                   15

 QUESTION 9: MAINTENANCE

 9.1 Preventative maintenance sub-groups
     • Planned or scheduled maintenance 
     • Condition based maintenance                                                        (2)

 9.2 Chain drive maintenance
     • Cleaning uncovered chain drives 
     • Check sprocket teeth and link plate wear 
     • Lubricating chain drives (manually or automatically) 
     • Checking the functioning of tensioning devices (idler sprocket)
     • Inspect chains regularly for elongation and record results      (Any 3 x 1)         (3)

 9.3 Cutting fluid maintenance
     • Check that there is sufficient flow of cutting fluid to the cutting tool ✓
     • Ensure that the sump is topped up from time to time ✓
     • Remove metal cutting from the machine's splash tray. ✓
     • Avoid contamination of the cutting fluid by draining and regularly
         replacing it.                                                     (Any 3 x 1)     (3)

 9.4 Viscosity
     Viscosity is the resistance of a fluid to flow.                                    (2)

 9.5 Advantageous characteristics for using nylon
     • Toughness 
     • Hard-wearing 
     • Needs little or no maintenance
     • Needs no lubrication
     • It is cheap
     • It is light
     • Can absorb shock
     • Resistant to chemicals
     • Endures high temperatures                                          (Any 2 x 1)      (2)

 9.6 Uses of Materials

       9.6.1     Teflon
                 • Orthopaedic and prosthetic appliances 
                 • Hearing aids
                 • Joints
                 • Upholstery
                 • Corrosion resistant mechanical parts (taps and bearings)
                 • Electrical insulation
                 • Non-stick coatings for cooking utensils              (Any 1 x 1)        (1)

Copyright reserved                                                            Please turn over

### Page 16

16             MECHANICAL TECHNOLOGY (FITTING AND MACHINING)   (EC/SEPTEMBER 2025)

       9.6.2      Glass fibre
                  Motor vehicle bodies 
                  Boats
                  Transparent roofing sheets
                  Petrol tanks
                  Swimming pools
                  Furniture
                  Fruit and salad bowls
                  Ornaments
                  Fishing rods                                                 (1)

 9.7 True or False

       9.7.1      True                                                        (1)

       9.7.2      False                                                       (1)

       9.7.3      False                                                       (1)

       9.7.4      True                                                       (1)
                                                                             [18]

Copyright reserved                                                 Please turn over

### Page 17

(EC/SEPTEMBER 2025)            MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                17

 QUESTION 10: JOINING METHODS (SPECIFIC)

 10.1   Pitch of screw thread
        • The pitch is the axial distance measured from any given point on the
           screw thread to a corresponding point on an adjacent thread.                   (2)

 10.2   Square thread terminology
        A – Crest/outside diameter 
        B – Effective/mean diameter or pitch diameter 
        C – Pitch 
        D – Helix angle 
        E – Cutting tool                                                                   (5)

 10.3   Square Thread Calculations:

        10.3.1        Lead = Pitch × number of starts
                                  =6x3
                                  = 18 mm                                                  (2)

        10.3.2        Mean diameter
                                                   1
                                           = OD - 2 pitch

                                                            1
                                                  = 78 - 2 (6) 

                                                  = 75 mm                                  (2)

        10.3.3                                     𝑙𝑒𝑎𝑑
                      Helix angle: tan 𝜃 = 𝑝𝑖𝑡𝑐ℎ 𝑐𝑖𝑟𝑐𝑢𝑚𝑓𝑒𝑟𝑒𝑛𝑐𝑒

                                                       18
                                           tan 𝜃 = 𝜋 ×75 

                                           𝜃 = tan-1 (0,0763…)

                                          𝜃 = 4,37°                                        (3)

        10.3.4        Leading tool angle = 90° – (helix + clearance angle)
                                                = 90° – (4,37° + 3°) 
                                                = 82,63o                                   (2)

        10.3.5        Following tool angle = 90° + (helix - clearance angle)
                                                  = 90° + (4,37° - 3°) 
                                                 = 91,37°                                 (2)
                                                                                          [18]

Copyright reserved                                                             Please turn over

### Page 18

18           MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                (EC/SEPTEMBER 2025)

 QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)

 11.1   Function of a belt
        • Transfer motion from pulley A to pulley B.                                    (2)

 11.2   Belt drives:

        11.2.1       Diameter of the driven pulley

                                                                                          (3)

        11.2.2       Power transmitted

                                                                                          (5)

                     NOTE: If driven diameter and speed is used to calculate power,
                           mark correct, i.e. 2 316,23 Watt.

Copyright reserved                                                            Please turn over

### Page 19

(EC/SEPTEMBER 2025)          MECHANICAL TECHNOLOGY (FITTING AND MACHINING)           19

 11.3 Speed ratio
                               𝐷𝑟𝑖𝑣𝑒𝑛
                 Speed ratio = 𝐷𝑟𝑖𝑣𝑒𝑟 

                               60
                              = 15 

                              =4:1                                                  (3)

 11.4 Hydraulics:

        11.4.1       Fluid pressure

                                                                                     (5)

Copyright reserved                                                      Please turn over

### Page 20

20           MECHANICAL TECHNOLOGY (FITTING AND MACHINING)   (EC/SEPTEMBER 2025)

        11.4.2       Force F on piston A

                                                                             (5)

        11.4.3       Distance X

Copyright reserved                                               Please turn over

### Page 21

(EC/SEPTEMBER 2025)   MECHANICAL TECHNOLOGY (FITTING AND MACHINING)           21

                                                                             (5)
                                                                            [28]

                                                                TOTAL:       200

Copyright reserved                                               Please turn over

## Related documents

- [MECH TECH GR12 MEMO SEPT2023 Welding Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-afrikaans/f45c553c-63a1-4e1c-b9c6-d426a3dfef26) — Mechanical Technology · Memo · 2023 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Mechanical Technology · Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Mechanical Technology · Memo · 2023 · Eng
- [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Mechanical Technology · Memo · 2023 · Eng
- [MECH TECH GR 12 MEMO SEPT 2020 Auto Afrikaans](https://www.hlayiso.com/library/mech-tech-gr-12-memo-sept-2020-auto-afrikaans/4a3289ca-f4a9-44a3-896e-c216c19a5874) — Mechanical Technology · Memo · 2020 · Afr
- [MECH TECH GR12 MEMO SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept-2020-auto-english/9066fed3-db75-4436-9ea3-0a432f99cc0b) — Mechanical Technology · Memo · 2020 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — QP · 2024 · Eng
- [MECH TECH GR12 QP SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept2023-welding-english/49e9215c-dc78-48c3-a526-4baaf59158d8) — QP · 2023 · Eng
- [Mechanical Technology May-June 2023 (Welding & Metalwork) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-afr/7d638feb-7218-4b3c-9f4c-ce95803d6e4f) — QP · 2023 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
