# Mechanical Technology Grade 12 Eastern Cape Mock 2020 Memo

> Grade 12 Mechanical Technology memorandum from the Eastern Cape Mock Exam 2020 (English), 18 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mech-tech-gr-12-memo-sept-2020-fitting-english/038eda25-7bf7-4eb1-a26e-d61119fb5a7a
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Language: English
- Document type: Memorandum
- Year: 2020
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 18

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 Eastern Cape Mock 2020 Memo](https://www.hlayiso.com/library/mech-tech-gr-12-memo-sept-2020-fitting-english/038eda25-7bf7-4eb1-a26e-d61119fb5a7a)

## About this document

Mechanical Technology · Grade 12 · Eastern Cape Mock Exam · 2020 · English. Memorandum, 18 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                           NATIONAL
                      SENIOR CERTIFICATE

                            GRADE 12

                       SEPTEMBER 2020

    MECHANICAL TECHNOLOGY: FITTING AND
                MACHINING
            MARKING GUIDELINE

MARKS:   200

                   This marking guideline consists of 18 pages.

### Page 2

Downloaded from hlayiso.com
2            MECHANICAL TECHNOLOGY: FITTING AND MACHINING               (EC/SEPTEMBER 2020)

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

 1.1     C                                                                             (1)

 1.2     B                                                                             (1)

 1.3     C                                                                             (1)

 1.4     A                                                                             (1)

 1.5     B                                                                             (1)

 1.6     C                                                                             (1)
                                                                                        [6]

 QUESTION 2: SAFETY (GENERIC)

 2.1     Gas welding (PPE)

             Eye protection 
             Overall / leather apron 
             Safety boots 
             Gloves                                                   (Any 2 x 1)     (2)

 2.2     Safety rules that must be followed whilst the surface grinder
         is in operation:

             Make sure that the sparks are of no danger to co-workers. 
             Do not force the material onto the grinding wheel. 
             Do not plunge grind. 
             Bring the material slowly into contact with the grinding wheel. 
             Never clean or adjust the machine whilst it is in motion. 
             Use cutting fluid. 
             Know where the emergency stop is located. 
             Stop machine before any adjustment 
             Keep tools clear from moving parts.                      (Any 2 x 1)     (2)

Copyright reserved                                                              Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: FITTING AND MACHINING                      3

2.3    Completing a task on any machine
       Switch the machine off.                                                        (1)

2.4    TWO safety precautions before switching the angle grinder on

          Make sure that there are no cracks or chips on the disc. 
          Make sure that the emery disc that is fitted is rated above the
           revolutions at which it is turned by the motor. 
          Make sure that the space between the tool rest and the emery disc
           does not exceed 3 mm. 
          Ensure that guards are in place. 
          When switching on the machine, do not stand in front of it, until it
           reaches its full speed. 
          Do not force or bump the work piece against the emery disc. 
          Grind only on the front surface of the wheel, not the sides. 
          All grinding machines must have a sign indicating the revolutions at
           which the spindle rotates.                                  (Any 2 x 1)    (2)

2.5   Importance of a welding helmet
       To protect your eyes and face from ultra-violet rays and radiation            (1)

2.6   Types of workshop layouts:
       Process layout 
       Product layout                                                                (2)
                                                                                      [10]

Copyright reserved                                                             Please turn over

### Page 4

Downloaded from hlayiso.com
4          MECHANICAL TECHNOLOGY: FITTING AND MACHINING                (EC/SEPTEMBER 2020)

 QUESTION 3: MATERIALS (GENERIC)

 3.1                                  DIFFERENT TYPES OF TESTS
        MATERIALS
                                Sound              Filing             Bend

        Cast iron         Very dull            Easy          Cannot bend /
                          sound                              Snaps/breaks /
                                                              Fractures easily 
        Mild steel        Medium metallic      Easy          Bends easily 
                          sound                                                         (6)

 3.2    Heat treatment process
         Is the heating and cooling of metals in their solid state so as to
          change their properties                                                       (1)

 3.3    Hardness factors:
         Workpiece size 
         Quenching rate 
         Carbon content                                             (Any 2 x 1)        (2)

 3.4    Heat treatment processes:

        3.4.1    Tempering
                  Is a process applied to steel and it relieves the strains
                   induced during the hardening process 
                  Decreases the degree of hardness 
                  Increases toughness 
                  Reduces brittleness 
                  Gives steel fine grain structure                    (Any 2 x 1)      (2)

        3.4.2    Annealing
                  Relieves internal stress 
                  Softens the metal 
                  Makes metal ductile 
                  Refines the grain structure 
                  Reduces brittleness                                (Any 2 x 1)       (2)

 3.5    Hardness of steel depends upon
         Carbon content                                                               (1)
                                                                                       [14]

Copyright reserved                                                             Please turn over

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: FITTING AND MACHINING              5

 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

 4.1    B                                                                     (1)

 4.2    D                                                                     (1)

 4.3    D                                                                     (1)

 4.4    A                                                                     (1)

 4.5    A                                                                     (1)

 4.6    B                                                                     (1)

 4.7    A                                                                     (1)

 4.8    B                                                                     (1)

 4.9    B                                                                     (1)

 4.10   A                                                                     (1)

 4.11   B                                                                     (1)

 4.12   B                                                                     (1)

 4.13   C                                                                     (1)

 4.14   B                                                                    (1)
                                                                             [14]

Copyright reserved                                                     Please turn over

### Page 6

Downloaded from hlayiso.com
6          MECHANICAL TECHNOLOGY: FITTING AND MACHINING                 (EC/SEPTEMBER 2020)

 QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE)
             (SPECIFIC)

 5.1    Lathe components
        5.1.1  Chuck is a lathe component used to mount and hold the
                 workpiece at one end.                                                 (1)

        5.1.2     Tool post is securely clamped to the compound slide and is
                   used to support and fasten the cutting tool in the proper
                   position for cutting action.                                        (1)

        5.1.3         Compound slide is situated on top of the cross slide and is
                       used for turning operations such as taper turning and thread
                       cutting.                                                        (1)

 5.2    Milling Cutters Classes
        5.2.1 Arbor cutters 
                Examples: plain cutter , side cutter, staggered-tooth cutter,
                slitting-saw cutter, angular cutter, profile/form cutters, side-and-
                face cutter, helical cutter                                            (2)

        5.2.2    Shank cutters 
                 Examples: end mill; shell end mill; T-slot cutter and Woodruff
                 keyseat cutter                                                        (2)

 5.3    Taper-turning calculations
         Θ = 8,5°
        θ/2 = 4,25°
        Tan θ/2 = (D – d )/ 2L 
        Tan 4,25 x 2 x 250 = (55-d) 
                         d = 17,84 mm
                         d = 18 mm                                                     (4)

 5.4    Dividing head components
        A – Index plate 
        B – Index crank 
        C – Sector arms 
        D – Single-start worm 
        E ‒ Worm wheel/gear                                                            (5)

 5.5    Lead calculations
        Lead = No. of starts x pitch
              = 3 x 1,75 mm 
              = 5,25 mm                                                                (2)
                                                                                       [18]

Copyright reserved                                                              Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: FITTING AND MACHINING                          7

 QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)

 6.1    Gear calculations:
        6.1.1 Dividing head: it breaks up the circumference of a circular
               workpiece into a number of equal parts. It is mounted between
               centers in cunjunction with the tailstock; or it can be fitted with
               a chuck for direct mounting of work.                                    (1)

        6.1.2    Index plate: to enable one revolution of the crank to be further
                 subdivided into fractions of a revolution, especially where the
                 fraction is the factor of 40.                                         (1)

        6.1.3    Sector arm: to enable indexing where fractions of turns are
                 required, so that it can be adjusted to any angle that would
                 contain a specific number of holes.                                   (1)

 6.2    Procedure to cut external metric V-screw thread using compound
        slide method.
         Set up the workpiece in the centre lathe and turn the part to be
            threaded to the required diameter of the thread. 
         Set the compound slide to 30º to the left of the centre line of that
            cross-slide and accurately set up the cutting tool in the tool post. 
         Consult the index plate of the quick-change gear box and shift the
            levers accordingly for the necessary pitch of the screw thread. 
         Start the centre lathe and set the cutting tool at touching point on
            the workpiece. 
         Move the cutting tool a short distance off, to clear the end of the
            workpiece and feed the compound slide 0,05 mm inwards. 
         With the centre lathe revolving, engage the half nuts at the correct
            line on the threading dial, putting the first cut of the screw thread in
            progress. 
         Stop the centre lathe and check the screw thread pitch with a
            screw thread pitch gauge.                                  (Any 5 x 1)     (5)

 6.3    Definition of Indexing: It is the process of evenly dividing the
        circumference of a circular work piece into equally spaced divisions,
        such as in cutting gear teeth, cutting splines, milling grooves in the
        reamers and taps.                                                              (1)

 6.4    Milling methods
         Up-cut milling 
         Down-cut milling                                                             (2)

Copyright reserved                                                                Please turn over

### Page 8

Downloaded from hlayiso.com
8          MECHANICAL TECHNOLOGY: FITTING AND MACHINING                      (EC/SEPTEMBER 2020)

 6.5    Differential indexing

        6.5.1    Indexing required

                                40
                 Indexing =          
                                𝐴
                        = 40/120

                            1       22
                        =       x        
                            3       22

                        = 22/66

                 Indexing is 22 holes in a 66-hole circle.                                  (3)

        6.5.2    Change of gears

                                     𝐷𝑟𝑖𝑣𝑒𝑟        𝐴−𝑁              40
                 Gear ratio :                 =                 x        
                                     𝐷𝑟𝑖𝑣𝑒𝑛             𝐴           1

                                                  120 −113
                                              =                 x 40 
                                                    120

                                                    7       8
                                              =+        x       
                                                    3       8

                                              = 56/24 

                 The driver gear has 56 teeth.
                 The driven gear has 24 teeth.                                              (5)

        6.5.3    The direction of motion is clockwise.
                 The crank handle will turn the same direction as the index
                 plate                                                                      (1)

Copyright reserved                                                                   Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: FITTING AND MACHINING                  9

 6.6    Dove tail calculations:

                Find the difference of distance over the rollers (L):
                L = (M ‒ R) – (m ‒ r) 
                  = (127,64 ‒ 25) – (100,32 ‒ 15) 
                  = 102,64 – 85,32
                L = 17,32 mm 

                For the angle θ
                       Tan θ/2 = (R ‒ r) / L 
                               = 10/17,32 

                              Θ = 30 x 2
                              Θ = 60°                                          (6)

 6.7    Constraints to balancing
         Requires specialised machinery 
         Difficult to ascertain the exact point of unbalance 
         Requires accurate removal or addition of material’s weight to the
           object. 
         Can lead to interference with parts of the machine when weights
           are added to parts                                   (Any 2 x 1)    (2)
                                                                               [28]

Copyright reserved                                                        Please turn over

### Page 10

Downloaded from hlayiso.com
10          MECHANICAL TECHNOLOGY: FITTING AND MACHINING   (EC/SEPTEMBER 2020)

 QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

 7.1    Hardness testers:
        7.1.1
        Brinell hardness tester

                                                                       (3)

        7.1.2
        Rockwell hardness tester

                                                                       (3)

 7.2    Hardness measure of a metal
         Resistance to penetration 
         Elastic hardness 
         Resistance to abrasion                                         (3)

Copyright reserved                                                Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: FITTING AND MACHINING                11

 7.3    Screw-thread micrometres
        6 + 0,5 + 0,3 = 6,80 mm                                             (2)

 7.4    Micrometre reading 41,25 mm

                                                                            (2)
                                                                             [13]

Copyright reserved                                                      Please turn over

### Page 12

Downloaded from hlayiso.com
12          MECHANICAL TECHNOLOGY: FITTING AND MACHINING              (EC/SEPTEMBER 2020)

 QUESTION 8: FORCES (SPECIFIC)

 8.1    Resultant force calculations:

                Xcom = 80 cos 30 – 40 cos 75 – 70 cos 25 – 50 cos 40 
                      = 80,0686 N 

                Ycom = 50 sin 40 – 80 sin 30 – 70sin 25 – 40 sin 75   
                       = ‒16,91 N 

                R      = √(𝑋 2 + 𝑌²) 
                R      = 81,836 N 

                       Tan θ = y/x
                       Tan Θ = 16,91/80,0 
                             Θ = 360 ‒ 11,925°
                                = 348,075° 

        Equilibrant = Resultant BUT IN THE OPPOSITE DIRECTION 

        Equilibrant = 81,836 N at 168,075°                                                     (12)

 8.2    Moments

        Converting the UDL to point lolad
        1 x 10 = 10 kN @ 5 mm from eft hand end 

        Calculation of the reactions.Taking moments:

        RD x 20 = (5 x 5) + (10 x 30) + (20 x 15) 
                 = 31,25 kN 
        (Ra x 20) + (10 x 10) = (20 x 5) + (5 x15) 
               = 3,75 kN 
                                                                                                 (5)

Copyright reserved                                                           Please turn over

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: FITTING AND MACHINING                     13

 8.3    Stress calculations:
        8.3.1 Tensile Stress Calculations
                             F = 10 kN; d = 20 mm: L = 2 m : E = 200 PGa
                                 𝐹
                             𝛿=
                                 𝐴
                               𝐴 = 𝜋𝑟 2
                             A = π x 0,01² 
                             A = 3,141 x 10^-4 m² 
                                 𝐹
                             δ=
                                 𝐴
                               = 10 000/3.141 x 10 ^-4
                               = 318,31 x 10⁶ Pa
                               = 318,31 MPa
                                                                                               (4)

        8.3.2    The change in length calculations.
                 𝛥𝐿 = ?; E = 200 GPa; F = 10 kN; L = 2 m; Ϭ = 318,31 MPa
                               𝑆𝑥𝐿
                        𝛥𝐿 =         
                                𝐸
                               = 318,31 x 10⁶ x 2) / 200 x 10⁹ 
                               = 0,318 mm                                                     (4)

 8.4    Stress/Strain diagram:

                                                                           

         A – Limit of proportionality 
         B – Elastic limit 
         C – Yield point 
         D – Maximum force / point 
         E – Point of fracture                                                                (6)

 8.5    FOS stands for Factor OR Safety or Safety Factor.                                     (1)

 8.6    Young’s modulus states that stress in metal is directly proportional to the
        strain it causes, provided the limit of proportionality is not exceeded.              (1)
                                                                                              [33]

Copyright reserved                                                             Please turn over

### Page 14

Downloaded from hlayiso.com
14          MECHANICAL TECHNOLOGY: FITTING AND MACHINING               (EC/SEPTEMBER 2020)

 QUESTION 9: MAINTENANCE (SPECIFIC)

 9.1    Purpose of composites:
        9.1.1 Bakelite can be used in disc brake cylinders, saucepan handles,
              distributor rotors, electrical plugs and switches, and parts for
              electrical irons.                                                            (2)

        9.1.2    Fibre glass is used as a surface covering, woven cloth, wearing
                 fibres, plastic covers and stuffing for pillow.                           (2)

        9.1.3    Carbon fibre is used for sport equipment like tennis, squash and
                 badminton racquets, racing bicycle frames, construction skis,
                 surfboards and boat masts, compressor blades for jet
                 engines.                                                                  (2)

 9.2    Reasons for using cutting fluid when working on the centre lathe:
         It prolongs the life of a cutting tool.          
         It prevents the shavings or metal chips from sticking and fusing to the
          cutting tool.                                          
         It will carry away the heat generated by the turning process.
         It flushes away shavings/metal chips.            
         It improves the quality of the finish of the turned surface.
                                                                       (Any 1 x 1)           (1)

 9.3    Mechanical drives:
         Gear drives 
         Chain drives 
         Belt drives                                                                       (3)

 9.4    Reasons for the use of carbon fibre:
         It is light in weight 
         It is tougher and stronger 
         It can be bent to any shape when heated above 150 ºC  (Any 2 x 1)                 (2)

Copyright reserved                                                            Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)      MECHANICAL TECHNOLOGY: FITTING AND MACHINING                           15

 9.5    ONE property and ONE use of each composite

            COMPOSITE                 PROPERTY                      USES
           9.5.1 PVC         - Durable                      - Bank credit cards
                             - Very versatile               - Shoe soles
                             - High load bearing            - Wallpaper
                               strength                     - Floor tiles
                             - High chemical                - Drip bags
                               resistance                   - Cooking oil bottles
                             - Very low co-efficient of                 (Any 1 x 1)
                               friction     (Any 1 x 1)

           9.5.2 Vesconite   - Withstands high              - Orthopaedic and
                               temperatures                   prosthetic
                             - Self-lubrication               appliances
                             - Resistant to water,          - Hearing aids
                               grease, heat and             - Upholstery
                               corrosion                               (Any 1 x 1)
                             - Good machinability
                                              (Any 1 x 1)
           9.5.3 Nylon       - Toughness                    - Bushes, toys,
                             - Hard-wearing                   curtain hooks
                             - Cheap                        - Gears
                             - Needs little                 - Pulleys
                               maintenance                             (Any 1 x 1)
                                              (Any 1 x 1)
                                                                                                (6)
                                                                                               [18]

Copyright reserved                                                                    Please turn over

### Page 16

Downloaded from hlayiso.com
16          MECHANICAL TECHNOLOGY: FITTING AND MACHINING            (EC/SEPTEMBER 2020)

 QUESTION 10:         JOINING METHODS (SPECIFIC)

 10.1 Square thread calculations:

        10.1.1 PCD = T x m
                   = 60 x 4 = 240 mm                                                         (2)

        10.1.2 Add = Module = 4                                                                (2)

        10.1.3 Clearance    = 0,157 x m
                            = 0,628 mm                                                       (2)

        10.1.4 Ded = 1,157 x m
                   = 4,628 mm                                                                (2)

        10.1.5 OD      = PCD + 2 x m
                       = 248 mm                                                              (2)

 10.2 Left-hand square screw-thread:
      A – Leading angle 
      B – Following or Trailing Angle 
      C – Clearance 
      D – Helix angle                                                                         (4)

 10.3 A multi-start thread allows for faster travel or movement and is more efficient
      as it loses less power to friction compared to single-start thread.                   (2 )

 10.4 Screw-thread fit is a combination of allowances and tolerances and a
      measure of tightness or looseness between the bolt and nut.                            (2)
                                                                                              [18]

Copyright reserved                                                         Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)        MECHANICAL TECHNOLOGY: FITTING AND MACHINING               17

 QUESTION 11: SYSTEMS AND CONTROL (SPECIFIC)

 11.1 Gear drives work on the principle that the turning motion of one gear be
      transferred to another gear if the gears are mounted close so that they mesh or
      engage.                                                                                (2)

 11.2 Hydraulic system calculations:

        11.2.1        Calculate the force applied on Piston A.
                      da = 30 mm; Db = 130 mm; M = 2 000 kg
                      Weight Calculation (W)
                      W=mxg
                       = 2 000 x 10
                       = 20 Kn 
                                                                                               (2)

        11.2.2        A = π (r)²
                      = π x 0,065² 
                      = 0,0133 m ² 

                                  𝐹
                             𝑃=
                                  𝐴
                      = 20 000/0,0133 
                      = 1,507 MPa 
                                                                                               (4)

        11.2.3        A = 𝜋Da²/4
                      = 𝜋 (0,03)²/4      
                                    −4
                      = 7,0686 x10 m² 
                      F= PxA
                      = 1,507 x 10 ⁶ x 7,068 x 10−4 
                      Force = 1065,235 N                                                      (4)

        11.2.4        Hydraulic system applications:
                      Machine tools, motor vehicle, hydraulic jacks       (Any 1 x 1)         (1)

 11.3 Velocity ratio is defined as the ratio of a distance through which any part of a
      machine moves, to that which the driving part moves during the same
      time.                                                                                  (2)

 11.4 Belt drive calculations:
      Nmotor x Dmotor = Nblade x Dblade 

        135 x 1 200 = 395 x Dblade 

        Dblade = 410,127 rpm 
                                                                                               (3)

Copyright reserved                                                          Please turn over

### Page 18

Downloaded from hlayiso.com
18          MECHANICAL TECHNOLOGY: FITTING AND MACHINING        (EC/SEPTEMBER 2020)

 11.5 Pneumatic drives:
       Vehicle painting 
       Air brakes 
       Opening and closing doors 
       Dismantling vehicle tire                                    (Any 3 x 1)           (3)

 11.6 Simple gear calculations:
      TA = 56 teeth; NA = 700 rpm

        11.6.1              𝑇𝐴 x 𝑁𝐴
                     TB =             
                              𝑁𝐵
                        = (56 x 700)/ 980 
                        = 40 teeth                                                        (3)

        11.6.2              𝑁𝐵 x 𝑇𝐵
                     Nc =             
                              𝑇𝑐
                     = (40 x 980)/ 64 
                     = 612,5 rpm                                                          (3)

        11.6.3       Driven gear will rotate anti-clockwise                               (1)
                                                                                          [28]

                                                                         TOTAL:           200

Copyright reserved                                                     Please turn over

## Related documents

- [MECH TECH GR12 MEMO SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept-2020-auto-english/9066fed3-db75-4436-9ea3-0a432f99cc0b) — Mechanical Technology · Memo · 2020 · Eng
- [MECH TECH GR12 QP SEPT 2020 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87) — Mechanical Technology · QP · 2020 · Eng
- [MECH TECH GR12 QP SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162) — Mechanical Technology · QP · 2020 · Eng
- [MECH TECH GR12 QP SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept2023-welding-english/49e9215c-dc78-48c3-a526-4baaf59158d8) — Mechanical Technology · QP · 2023 · Eng
- [MECHANICAL TECH (Auto) MEMO SEPT 2018 English](https://www.hlayiso.com/library/mechanical-tech-auto-memo-sept-2018-english/b985e4dd-9a08-4ec2-a07b-64edd6f727ea) — Mechanical Technology · Memo · 2018 · Eng
- [MECHANICAL TECH (Welding) GR12 MEMO SEPT 2018 English](https://www.hlayiso.com/library/mechanical-tech-welding-gr12-memo-sept-2018-english/1b0b4dd6-b53e-485d-9068-6f378eb8c9f3) — Mechanical Technology · Memo · 2018 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — QP · 2024 · Eng
- [Mechanical Technology May-June 2023 (Welding & Metalwork) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-afr/7d638feb-7218-4b3c-9f4c-ce95803d6e4f) — QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-eng/1523a16f-2012-4f13-a922-86cbb5900666) — QP · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
