# Mechanical Technology Grade 12 Eastern Cape Mock 2020 QP

> Grade 12 Mechanical Technology question paper from the Eastern Cape Mock Exam 2020 (English), 18 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2020
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 18

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 Eastern Cape Mock 2020 QP](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162)

## About this document

Mechanical Technology · Grade 12 · Eastern Cape Mock Exam · 2020 · English. Question paper, 18 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                 NATIONAL
                            SENIOR CERTIFICATE

                                  GRADE 12

                             SEPTEMBER 2020

        MECHANICAL TECHNOLOGY: AUTOMOTIVE

MARKS:     200

TIME:      3 hours

        This question paper consists of 18 pages, including a 1-page formula sheet.

### Page 2

Downloaded from hlayiso.com
2                      MECHANICAL TECHNOLOGY (AUTOMOTIVE)                    (EC/SEPTEMBER 2020)

 INSTRUCTIONS AND INFORMATION

 1.        Write your full names on the ANSWER BOOK.

 2.        Answer ALL the questions.

 3.        Number the answers correctly according to the numbering system used in
           this question paper.

 4.        Start EACH question on a NEW page.

 5.        Show ALL calculations and units. Round off final answers to TWO decimal
           places.

 6.        Candidates may use non-programmable scientific calculators and drawing
           instruments.

 7.        The value of gravitational acceleration should be taken as 10 m.s-2

 8.        All dimensions are in millimeters, unless stated otherwise in the question.

 9.        A formula sheet is attached to the question paper.

 10.       Write neatly and legibly.

 11.       Use the criteria below to assist you in managing your time.

 QUESTION                            CONTENT                                           TIME
                                                                         MARKS
                                     GENERIC                                        in minutes
       1          Multiple-choice questions                               6               6
       2          Safety                                                  10             10
       3          Materials                                               14             14
                                     SPECIFIC
       4          Multiple-choice questions                               14             10
       5          Tools and Equipment                                     23             20
       6          Engines                                                 28             25
       7          Forces                                                  32             25
       8          Maintenance                                             23             20
       9          Systems and Control (Automatic Gearbox)                 18             20
                  Systems and Control (Axles, Steering Geometry
       10                                                                 32             30
                  and Electronics)
                                                         TOTAL            200            180

Copyright reserved                                                                 Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)          MECHANICAL TECHNOLOGY (AUTOMOTIVE)                             3

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

 Various options are provided as possible answers to the following questions. Choose
 the correct answer and write only the letter (A–D) next to the question numbers
 (1.1–1.6) in the ANSWER BOOK, for example 1.7 D.

 1.1    Which of the following safety measures is applicable to guillotines in terms of
        the Occupational Health and Safety Act?

        A       Clamp the workpiece securely to the table.
        B       Do not leave the chuck key on the machine.
        C       Machine must be fitted with fixed guards to prevent fingers from reaching
                through the point of operation.
        D       Use the table of the machine as an anvil.                                 (1)

 1.2    What is the purpose of cooling the blade of a band saw with cutting fluid?

        A        To cause friction
        B        To ensure clean cuts and remove metal waste
        C        To ensure straight cuts
        D        To move the blade forward and backwards                                    (1)

Copyright reserved                                                       Please turn over

### Page 4

Downloaded from hlayiso.com
4                     MECHANICAL TECHNOLOGY (AUTOMOTIVE)                  (EC/SEPTEMBER 2020)

 1.3    Which ONE of the following safety procedures is applicable to the operation
        of a hydraulic press?

        A     Do not apply wrench to revolving work.
        B     Guards could be removed when pressing soft material.
        C     Pressure gauges must be tested regularly and adjusted or replaced if
              any malfunction occurs.
        D     Use the machine table as an anvil.                                           (1)

 1.4    Which ONE of the following tests is used to measure the ductility of a metal?

        A     Bend tests
        B     Sound tests
        C     Hardness tests
        D     Machining tests                                                              (1)

 1.5    File tests are used as the simplest method of checking the ... of material.

        A     toughness
        B     hardness
        C     ductility
        D     softness                                                                     (1)

 1.6    Sound tests can be performed by tapping a material with a …

        A     hacksaw.
        B     spanner.
        C     hammer.
        D     file.                                                                        (1)
                                                                                           [6]

Copyright reserved                                                              Please turn over

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)        MECHANICAL TECHNOLOGY (AUTOMOTIVE)                              5

 QUESTION 2: SAFETY (GENERIC)

 2.1    Name any TWO pieces of personal safety equipment that you need to wear
        when using gas welding equipment.                                                 (2)

 2.2    Give TWO safety rules that must be followed while the surface grinder is in
        operation.

                                                                                          (2)

 2.3    When completing a task on any machine, what safety aspect must be
        considered before leaving the machine?                                            (1)

 2.4    State TWO safety measures to observe before switching the angle grinder
        on.

                                                                                          (2)

 2.5    Why is it important to wear a welding helmet when using arc welding
        equipment?                                                                        (1)

 2.6    Name TWO types of workshop layouts.                                               (2)
                                                                                         [10]

Copyright reserved                                                    Please turn over

### Page 6

Downloaded from hlayiso.com
6                     MECHANICAL TECHNOLOGY (AUTOMOTIVE)                 (EC/SEPTEMBER 2020)

 QUESTION 3: MATERIALS (GENERIC)

 3.1    The following table shows the different types of tests and materials.
        Copy and complete the table in your ANSWER BOOK by stating how these
        materials will react under the different tests.

                                         DIFFERENT TYPES OF TESTS
        MATERIALS
                                 Sound               Filing                Bend

        Cast iron

        Mild steel
                                                                                               (6)

 3.2    Explain the purpose of heat-treatment processes.                                       (1)

 3.3    The hardness that can be achieved from a specific treatment depends upon
        THREE factors. Name any TWO factors.                                                   (2)

 3.4    Explain the purpose of the following heat treatment processes:

        3.4.1    Tempering                                                                     (2)

        3.4.2    Annealing                                                                     (2)

 3.5    What does the hardness of steel depend upon?                                            (1)
                                                                                               [14]

Copyright reserved                                                             Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)         MECHANICAL TECHNOLOGY (AUTOMOTIVE)                              7

 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

 Various options are provided as possible answers to the following questions.
 Choose the answer and write only the letter (A–D) next to the question numbers
 (4.1–4.14) in the ANSWER BOOK, for example 4.15 A.

 4.1    FIGURE 4.1 shown below is an OBDII car diagnosis machine.

                                          FIGURE 4.1

        Which ONE of the following applications does NOT require the use of this
        tool?

        A     Determine the castor angle of a wheel
        B     Scan a car electronic control module (ECM)
        C     Detect faults in the form of codes
        D     Clear errors decoded by a car electronic control module                      (1)

 4.2    During the process of applying the emission gas analyser on a car’s
        exhaust system, which ONE of the following set-up procedures is NOT
        applicable?

        A     Connect the analyser to the 12-volt vehicle battery terminals
        B     Do not connect the armoured hose from the condenser pick-up to the
              rear of the machine until the display is 0.00
        C     Release the pressure built up in the system with the pressure release
              valve
        D     Insert the silicon hose probe and clamp unto the exhaust tail pipe           (1)

 4.3    Which ONE of the following types of equipment is used to determine the
        percentage leakage of a cylinder in an internal combustion engine?

        A     Bubble gauge
        B     Emission gas analyser
        C     Compression tester
        D     Cylinder leakage tester                                                      (1)

Copyright reserved                                                      Please turn over

### Page 8

Downloaded from hlayiso.com
8                     MECHANICAL TECHNOLOGY (AUTOMOTIVE)                (EC/SEPTEMBER 2020)

 4.4    Identify the equipment shown in FIGURE 4.4 below.

                                        FIGURE 4.4

        A     Pump
        B     Brake band
        C     Stator
        D     Impeller                                                                       (1)

 4.5    What is the name of the total volume displaced when a piston moves from
        bottom dead centre to top dead centre in an internal combustion?

        A     Clearance volume
        B     Swept volume
        C     Compression volume
        D     Cylinder volume                                                                (1)

 4.6    What is the purpose of the waste gate of a turbocharger of an internal
        combustion engine?

        A     Provides more boost to the engine
        B     Cool the air coming to the inlet manifold
        C     Waste excess oxygen coming to the combustion chamber
        D     Waste some exhaust gases by causing it to bypass the turbocharger
              turbine                                                                       (1)

Copyright reserved                                                               Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)          MECHANICAL TECHNOLOGY (AUTOMOTIVE)                             9

 4.7     FIGURE 4.7 shown below is a supercharger.

                                          FIGURE 4.7

         Identify the type of supercharger:

         A      Roots supercharger
         B      Centrifugal supercharger
         C      Twin-screw supercharger
         D      Sliding-vane supercharger                                                   (1)

 4.8     What is the purpose of a catalytic converter in the exhaust system of a
         spark ignition (SI) engine vehicle?

         A      Regulates the amount of oxygen in the exhaust manifold
         B      Permits the flow of exhaust gases in one direction only
         C      Prevents flow of exhaust gases
         D      Converts the pollutants in the exhaust gases of the engine into a non-
                toxic substance                                                             (1)

 4.9     Lambda oxygen sensors are installed in the exhaust outlet of the turbine of
         turbo chargers to sense the oxygen content of the exhaust gases. Why are
         they installed in turbocharged cars?

         A      Turbocharged cars have a high carbon exhaust content
         B      Turbocharged cars have a high air boost in the inlet manifold
         C      Turbocharged cars have a high fuel consumption
         D      There is no air flow metre                                                  (1)

 4.10    How does the idle speed control valve influence the speed of an engine at
         cold start?

         A      Increases the speed of an engine at cold start
         B      Decreases the speed of an engine at cold start
         C      Prevents the engine from overheating by regulating the idle speed at
                cold start
         D      Causes the engine to stop running as the temperature rises                  (1)

Copyright reserved                                                       Please turn over

### Page 10

Downloaded from hlayiso.com
10                    MECHANICAL TECHNOLOGY (AUTOMOTIVE)               (EC/SEPTEMBER 2020)

 4.11    Which ONE of the following is the correct function of the throttle position
         sensor in an air induction system?

         A     Controls the oxygen content in the exhaust gases
         B     Adjusts the throttle valve for maximum performance
         C     Detects the position of the throttle valve
         D     Detects the position of the camshaft                                      (1)

 4.12    Identify the type of gear system arrangement displayed in FIGURE 4.12
         below.

                                          FIGURE 4.12

         A     Double gear arrangement
         B     Single gear arrangement
         C     Double epicyclic gear system
         D     Single epicyclic gear system                                              (1)

 4.13    Which ONE of the following is a possible cause of an engine over-heat?

         A     Faulty alternator
         B     Faulty water pump
         C     Too much oil in the sump
         D     Leakage in the fuel line                                                  (1)

 4.14    How does camber affect tyre wears?

         A     One side of the tyre wears excessively
         B     Thin outer or inner edge wear
         C     Uniform tyre wear
         D     Prevents tyre wear                                                        (1)
                                                                                        [14]

Copyright reserved                                                           Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)          MECHANICAL TECHNOLOGY (AUTOMOTIVE)                              11

QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)
5.1    The figure below shows the alignment equipment used in an automotive
       workshop. Answer the questions that follow.

                                         A

                                                                  B

                                                                  C

                                                                  D

                                                                  E

                                         FIGURE 5.1

       5.1.1    Identify the equipment in FIGURE 5.1.                                       (1)

       5.1.2    Label parts A–E.                                                            (5)

       5.1.3    List THREE alignment angles that can be tested with the tool in
                FIGURE 5.1 above.                                                           (3)

5.2    In point form, describe the set-up procedures you must follow when reading
       the camber in the alignment settings of a car suspension system using a
       bubble gauge.                                                                        (5)

5.3    Name THREE faults that can be established when performing dynamic wheel
       balancing.                                                                           (3)

5.4    What is the main purpose of the following tools in an automotive workshop?

       5.4.1    Turn table                                                                  (2)

       5.4.2    Wheel balancer                                                              (2)

       5.4.3    Optical alignment tool                                                       (2)
                                                                                            [23]

Copyright reserved                                                       Please turn over

### Page 12

Downloaded from hlayiso.com
12                    MECHANICAL TECHNOLOGY (AUTOMOTIVE)               (EC/SEPTEMBER 2020)

 QUESTION 6: ENGINES (SPECIFIC)

 6.1 A crankshaft is subject to vibrations as the engine runs. Give TWO factors
     responsible for this vibration.                                                     (2)

 6.2 List TWO types of vibration damper used in an engine.                               (2)

 6.3 How does the following built-in feature improve engine balance?

       6.3.1   Crankshaft                                                                (2)

       6.3.2   Connecting rods and pistons                                               (2)

       6.3.3   Flywheels                                                                 (2)

 6.4 State THREE factors that determine the configuration of an engine.                  (3)

 6.5 List any TWO types of engine cylinder configurations.                               (2)

 6.6 What type of engine configuration is displayed in FIGURE 6.6 below?

                                        FIGURE 6.6                                       (1)

 6.7 Give TWO factors that determine the firing order of an engine.                      (2)

 6.8 What is the firing order of a five cylinder in-line engine?                         (1)

Copyright reserved                                                           Please turn over

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)        MECHANICAL TECHNOLOGY (AUTOMOTIVE)                           13

 6.9    The figure below shows the internal components of a turbo charger. Label
        parts A–F.

                                                                                         (6)
                                       FIGURE 6.9

 6.10   List any THREE disadvantages of using a turbocharger in an internal
        combustion engine.                                                               (3)
                                                                                        [28]

Copyright reserved                                                   Please turn over

### Page 14

Downloaded from hlayiso.com
14                    MECHANICAL TECHNOLOGY (AUTOMOTIVE)               (EC/SEPTEMBER 2020)

 QUESTION 7: FORCES (SPECIFIC)

 7.1 What do you understand by the term compression ratio?                            (2)

 7.2 A compression ignition engine (CI) has a cylinder diameter of 90 mm, a
     stroke length of 110 mm and a clearance volume of 70 cm3.

       Calculate the compression ratio of the engine.                                 (6)

 7.3 What will be the new compression ratio of the engine IF the engine in
     QUESTION 7.2 undergoes overhauling and in the process the bore is
     increased to 96,1 mm in order to fit into a bigger, new piston?                  (4)

 7.4 Give any FOUR methods that can be used to raise the compression ratio of
     an internal combustion engine.                                                   (4)

 7.5 What do you understand by the term indicated power of an engine?                 (2)

 7.6 The following data was recorded during a test carried out on a four-stroke,
     four-cylinder petrol engine:

       Mean effective pressure on the piston:      1 200 kPa
       Length of stroke:                           86 mm
       Cylinder bore:                              90 mm
       Revolutions per minute:                     4 200 rpm
       Torque:                                     180 Nm @ 4200 rpm
       Number of cylinders:                         4

       Calculate the following:

       7.6.1.   Indicated power in kW                                                   (7)

       7.6.2.   The brake power in kW                                                   (3)

       7.6.3.   Mechanical efficiency                                                   (2)

 7.7 What do you understand by the term mechanical efficiency of an internal
     combustion engine?                                                                 (2)
                                                                                       [32]

Copyright reserved                                                           Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)         MECHANICAL TECHNOLOGY (AUTOMOTIVE)                           15

 QUESTION 8: MAINTENANCE (SPECIFIC)

 8.1 A car exhaust gas was analysed and it was discovered that there was a high
     carbon monoxide reading.

       8.1.1    State THREE possible causes that may be responsible for the high
                carbon monoxide reading.                                                  (3)

       8.1.2    Give THREE necessary measures that can be taken to correct the
                faults.                                                                   (3)

       8.1.3    Name THREE other gases that may be analysed during the process
                of exhaust gas analysis.                                                  (3)

 8.2 During the process of compression testing on a 6-cylinder SI engine, it was
     discovered that two of the cylinders had an unusually low reading. What will
     be the next step to verify the condition of these two cylinders?                     (1)

 8.3 During a cylinder leakage testing procedure, it was discovered that there are
     some signs of failure in the cylinders. What are the possible causes of the
     following failures?

       8.3.1   Hissing sound from the inlet manifold                                      (1)

       8.3.2   Bubbles from radiator                                                      (1)

       8.3.3   Hissing sound from the dip stick                                           (1)

 8.4 Give FOUR manufactural specifications that must be taken into account when
     conducting oil pressure testing.                                                     (4)

 8.5 List THREE possible causes of low fuel pressure readings during fuel
     pressure testing.                                                                    (3)

 8.6 List any THREE possible components where the coolant could leak during
     cooling system pressure testing.                                                     (3)
                                                                                         [23]

Copyright reserved                                                    Please turn over

### Page 16

Downloaded from hlayiso.com
16                      MECHANICAL TECHNOLOGY (AUTOMOTIVE)              (EC/SEPTEMBER 2020)

 QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX)
             (SPECIFIC)

 9.1    What was the main purpose behind the design of an automatic gearbox in
        place of a manually driven gearbox?                                             (2)

 9.2     Give THREE advantages of using an automatic gear box.                          (3)

 9.3     The diagram in FIGURE 9.3 below shows one of the components of an
         automatic transmission system.

                                           FIGURE 9.3

         Use the diagram to answer the following questions.

         9.3.1       Identify the equipment in FIGURE 9.3 above.                        (1)

         9.3.2       Label parts A–E in FIGURE 9.3 above.                               (5)

         9.3.3       State THREE functions of the equipment in FIGURE 9.3 above.        (3)

         9.3.4       What is the function of the part labelled C?                       (2)

 9.4     When the speed in a torque converter increases, how will it influence the
         torque multiplication?                                                         (2)
                                                                                       [18]

Copyright reserved                                                            Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)              MECHANICAL TECHNOLOGY (AUTOMOTIVE)                                17

 QUESTION 10: SYSTEMS AND CONTROL (AXLES, STEERING
              GEOMETRY AND ELECTRONICS) (SPECIFIC)

 10.1    State FOUR properties of a good steering mechanism.                                       (4)

 10.2    With the aid of a neat and well labelled sketch, demonstrate the toe-in of
         the front wheel of a motor vehicle.                                                       (4)
 10.3    State the purpose of each of the following angles:

         10.3.1       Caster                                                                       (2)

         10.3.2       Ackermann principle                                                          (2)

         10.3.3       King pin inclination                                                         (2)
 10.4    The diagram in FIGURE 10.4 below shows an alignment angle of a car
         front wheel. Answer the questions that follow.

                                                   B                       C
                                                                           D

                                                                       E

                                             A
                                                                                 F
                                                 FIGURE 10.4

         10.4.1       Identify the type of alignment angle in FIGURE 10.4 above.                   (1)

         10.4.2       Label the parts A–F in FIGURE 10.4 above.                                    (6)

         10.4.3       Briefly explain the type of alignment angle displayed in
                      FIGURE 10.4 above.                                                           (2)

 10.5    List FIVE factors that must be taken into account before wheel alignment
         can be checked or adjusted.                                                               (5)

 10.6    What is the purpose of wheel balancing?                                                   (2)

 10.7    Name the TWO types of wheel balancing used in tyre fitment centers.                       (2)
                                                                                                  [32]

                                                                                  TOTAL:          200

Copyright reserved                                                             Please turn over

### Page 18

Downloaded from hlayiso.com
18                        MECHANICAL TECHNOLOGY (AUTOMOTIVE)                           (EC/SEPTEMBER 2020)

       FORMULA SHEET FOR MECHANICAL TECHNOLOGY (AUTOMOTIVE)

       Force  m  a       where m  mass
                                   a  accelerati on

       Work  force  distance (F  d)

                 force  distance
       Power 
                       time

       Torque  force  radius

       Indicated power  P  L  A  N  n
       where             P  mean effective pressure
                           L  length of stroke
                         A  area of piston crown
                         N  number of power strokes per second
                          n  number of cylinders

       Brake power  2 π N  T
       where         N  revolutions per second
                      T  torque

       Brake power (Prony brake)  F  2  π  R  N
       where                        F  force
                                    R  length of brake arm
                                   N  revolutions per second

                                     brake power
       M echanical efficiency                      100
                                   indicated power

                              swept volume  clearance volume
       Compression ratio 
                                     clearance volume

                               π  D2                                          π  D2
       where swept volume            L                   Clearance volume           l
                                  4                                               4
       where L  length of stroke                          where D  diameter of bore
               D  diameter of bore                              l  clearance

                      product of the number of teeth of the driven gears
       Gear ratio 
                      product of the number of teeth of the driver gears

Copyright reserved                                                                           Please turn over

## Related documents

- [MECH TECH GR12 QP SEPT 2020 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87) — Mechanical Technology · QP · 2020 · Eng
- [MECH TECH GR12 MEMO SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept-2020-auto-english/9066fed3-db75-4436-9ea3-0a432f99cc0b) — Mechanical Technology · Memo · 2020 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Mechanical Technology · Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Mechanical Technology · Memo · 2023 · Eng
- [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Mechanical Technology · Memo · 2023 · Eng
- [MT Nov 2020 (Automotive) Eng](https://www.hlayiso.com/library/mt-nov-2020-automotive-eng/489fabb7-3cad-4d15-965e-29f7af36ce41) — Mechanical Technology · QP · 2020 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng
- [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — QP · 2023 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
