# Mechanical Technology Grade 12 Eastern Cape Mock 2020 QP

> Grade 12 Mechanical Technology question paper from the Eastern Cape Mock Exam 2020 (English), 19 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2020
- Exam period: Eastern Cape Mock Exam
- Curriculum: CAPS
- Pages: 19

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 Eastern Cape Mock 2020 QP](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-welding-english/fb1b7d42-462f-47a9-b370-31ff67b36f87)

## About this document

Mechanical Technology · Grade 12 · Eastern Cape Mock Exam · 2020 · English. Question paper, 19 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                 NATIONAL
                            SENIOR CERTIFICATE

                                       GRADE 12

                             SEPTEMBER 2020

    MECHANICAL TECHNOLOGY: WELDING AND
                METALWORK

MARKS:      200

TIME:       3 hours

         This question paper consists of 19 pages, including a 1 page formula sheet.

### Page 2

Downloaded from hlayiso.com
2           MECHANICAL TECHNOLOGY: WELDING AND METALWORK                     (EC/SEPTEMBER 2020)

 INSTRUCTIONS AND INFORMATION

 1.     Write your full name(s) on the ANSWER BOOK.

 2.     Answer ALL the questions.

 3.     Number the answers correctly according to the numbering system used in this
        question paper.

 4.     Start EACH question on a NEW page.

 5.     Show ALL calculations and units. Round off final answers to TWO decimal
        places.

 6.     Candidates may use non-programmable scientific calculators and drawing
        instruments.

 7.     The value of gravitational acceleration should be taken as 10 m/s2.

 8.     All dimensions are in millimetres, unless stated otherwise in the question.

 9.     A formula sheet is attached to the question paper.

 10.    Write neatly and legibly.

 11.    Use the criteria below to assist you in managing your time.

                                                                                      TIME
    QUESTION                         CONTENT                          MARKS
                                                                                   in minutes
                                      GENERICS
       1             Multiple-choice questions                          6               10
       2             Safety                                            10               15
       3             Materials                                         14               15
                                       SPECIFIC
       4             Multiple-choice questions                         14               13
       5             Terminology (Templates)                            23              18
       6             Tools and Equipment                                18              15
       7             Forces                                             45              30
       8             Joining Methods (Inspection of Weld)               23              18
       9             Joining Methods (Stresses and Distortion)          18              18
       10            Maintenance                                         8              10
       11            Development                                        21              18
                                                           TOTAL       200             180

Copyright reserved                                                             Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: WELDING AND METALWORK                         3

 SECTION A: GENERIC

 QUESTION 1: MULTIPLE-CHOICE (GENERIC)

 Various options are provided as possible answers to the following questions. Choose
 the correct answer and write only the letter (A–D) next to the question numbers
 (1.1–1.6) in the ANSWER BOOK, for example 1.7 D.

 1.1     Which of the following safety measures is applicable to guillotines in terms
         of the Occupational Health and Safety Act?

         A      Clamp the workpiece securely to the table.
         B      Do not leave the chuck key on the machine.
         C      Machine must be fitted with fixed guards to prevent fingers from
                reaching through the point of operation.
         D      Use the table of the machine as an anvil.                                  (1)

 1.2     What is the purpose of cooling the blade of a band saw with cutting fluid?

         A      To cause friction
         B      To ensure clean cuts and remove metal waste
         C      To ensure straight cuts
         D      To move the blade forward and backwards                                    (1)
Copyright reserved                                                            Please turn over

### Page 4

Downloaded from hlayiso.com
4             MECHANICAL TECHNOLOGY: WELDING AND METALWORK                   (EC/SEPTEMBER 2020)

 1.3      Which ONE of the following safety procedures is applicable to the operation
          of a hydraulic press?

          A     Do not apply wrench to revolving work.
          B     Guards could be removed when pressing soft material.
          C     Pressure gauges must be tested regularly and adjusted or replaced if
                any malfunction occurs.
          D     Use the machine table as an anvil.                                           (1)

 1.4      Which ONE of the following tests is used to measure the ductility of a
          metal?

          A     Bend tests
          B     Sound tests
          C     Hardness tests
          D     Machining tests                                                              (1)

 1.5      File tests are used as the simplest method of checking the ... of material.

          A     toughness
          B     hardness
          C     ductility
          D     softness                                                                     (1)

 1.6      Sound tests can be performed by tapping a material with a …

          A     hacksaw.
          B     spanner.
          C     hammer.
          D     file.                                                                        (1)
                                                                                             [6]

Copyright reserved                                                              Please turn over

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)    MECHANICAL TECHNOLOGY: WELDING AND METALWORK                        5

 QUESTION 2: SAFETY (GENERIC)

 2.1    Name any TWO pieces of personal safety equipment that you need to wear
        when using gas welding equipment.                                               (2)

 2.2    Give TWO safety rules that must be followed while the surface grinder is in
        operation.

                                                                                        (2)

 2.3    When completing a task on any machine, what safety aspect must be
        considered before leaving the machine?                                          (1)

 2.4    State TWO safety measures to observe before switching the angle grinder
        on.

                                                                                        (2)

 2.5    Why is it important to wear a welding helmet when using arc welding
        equipment?                                                                      (1)

 2.6    Name TWO types of workshop layouts.                                             (2)
                                                                                      [10]

Copyright reserved                                                          Please turn over

### Page 6

Downloaded from hlayiso.com
6           MECHANICAL TECHNOLOGY: WELDING AND METALWORK                 (EC/SEPTEMBER 2020)

 QUESTION 3: MATERIALS (GENERIC)

 3.1    The following table shows the different types of tests and materials.
        Copy and complete the table in your ANSWER BOOK by stating how these
        materials will react under the different tests.

                                     DIFFERENT TYPES OF TESTS
        MATERIALS
                             Sound                  Filing               Bend

        Cast iron
        Mild steel                                                                       (6)

 3.2    Explain the purpose of heat-treatment processes.                                  (1)

 3.3    The hardness that can be achieved from a specific treatment depends upon
        THREE factors. Name any TWO factors.                                              (2)

 3.4    Explain the purpose of the following heat treatment processes:

        3.4.1    Tempering                                                                (2)

        3.4.2    Annealing                                                                (2)

 3.5    What does the hardness of steel depend upon?                                     (1)
                                                                                        [14]

Copyright reserved                                                         Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)    MECHANICAL TECHNOLOGY: WELDING AND METALWORK                        7

 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

 Various options are given as possible answers to the following questions. Choose
 the answer and write only the letter (A–D) next to the question numbers (4.1–1.14)
 in the ANSWER BOOK, for example 4.15 A.

 4.1    Which of the following best describes a template loft?

        A     It is the heart of the structural workshop.
        B     It is the welding workshop for roof trusses.
        C     It is the drawing workshop for roof trusses.
        D     It is where complicated steel structures are kept.                         (1)

 4.2    What is the purpose of a supplementary symbol?

        A     To show you where to weld
        B     To indicate where to weld
        C     To indicate side weld in a welding joint
        D     To indicate additional information about the weld                          (1)

 4.3    What is the maximum thickness of sheet metal that can be cut with a hand
        guillotine?

        A     3,2 mm
        B     1,6 mm
        C     1,2 mm
        D     2,1 mm                                                                     (1)

 4.4    Identify the following weld symbol.

        A     Butt joint
        B     Lap joint
        C     Fillet weld symbol
        D     Square butt symbol                                                         (1)

Copyright reserved                                                          Please turn over

### Page 8

Downloaded from hlayiso.com
8           MECHANICAL TECHNOLOGY: WELDING AND METALWORK                     (EC/SEPTEMBER 2020)

 4.5    Which property of material is tested using a Brinell tester?

        A     Tensile strength
        B     Elasticity
        C     Hardness
        D     Brittleness                                                                   (1)

 4.6    Which ONE of the following safety regulations applies to the MIG/MAGS
        welding process?

        A     Check the colour coding on cylinders.
        B     Hold the workpiece in your hand during the welding process.
        C     Turn the relief valve very slowly.
        D     Ensure that the welding area is well-ventilated.                              (1)

 4.7    What is the purpose of cooling the blade of a power saw with cutting fluid?

        A     To cause friction
        B     To ensure small cuts with no wastage
        C     To ensure a straight cut
        D     To prevent the blade from overheating and binding or breaking                 (1)

 4.8    Calculate Young’s modulus of elasticity for a metal with a strain value of
        2 x 10-3 caused by stress of 6 MPa.

        A     12 MPa
        B     3 MPa
        C     12 GPa
        D     3 GPa                                                                         (1)

 4.9    Stress can be defined as an internal force in a material resisting a/an …

        A     internal load.
        B     spin load.
        C     moving load.
        D     external load.                                                                (1)

Copyright reserved                                                             Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: WELDING AND METALWORK                         9

 4.10     When does overloading occur in a pedestal drill?

          A      When the drill bit is forced into the material
          B      When the chuck is forced into the material
          C      When excessive force is applied on the machine
          D      When the machine is moving fast                                          (1)

 4.11     Which ONE of the following is an inspection during arc welding?

          A      Rate of rod burning and the progress of the weld
          B      Correct flame for the work on hand
          C      Correct angle of the blow pipe
          D      Depth of fusion                                                          (1)

 4.12     Which ONE of the following is a cause for undercutting during arc
          welding?

          A      Clean bead
          B      Travel speed too high
          C      Slag inclusion
          D      Distortion                                                               (1)

 4.13     A destructive test is a method of testing a weld …

          A      without destroying the finished product.
          B      by destroying the finished product.
          C      by weld defects.
          D      without weld defects.                                                    (1)

 4.14     Which ONE of the following factors influences the rate of cooling of the
          weld metal during the welding process?

          A      Weld metal thickness
          B      Amount of oxygen used in process
          C      Current setting of the welding machine
          D      Electrode thickness                                                     (1)
                                                                                        [14]

Copyright reserved                                                            Please turn over

### Page 10

Downloaded from hlayiso.com
10            MECHANICAL TECHNOLOGY: WELDING AND METALWORK                      (EC/SEPTEMBER 2020)

 QUESTION 5: TERMINOLOGY (TEMPLATES) (SPECIFIC)

 5.1      Define a template loft.                                                                     (2)

 5.2      Describe THREE qualities of a good template loft.                                           (3)

 5.3      State the function of a web template.                                                       (2)

 5.4      A steel ring with an outside diameter of 500 mm must be manufactured from a
          30 x 30 mm square bar.

          5.4.1      Calculate the dimensions of the required materials.                              (6)

          5.4.2      Make a neat sketch of the steel ring indicating all the dimensions of the
                     material.                                                                        (4)

 5.5      Make a neat sketch of a weld symbol indicating the following information of a
          site weld on a T-joint done with arc welding.

               The intermitted square butt weld on both sides is 10 mm in size
               The lengths of the weld beads are 60 mm each
               The pitch of the weld is 100 mm                                                    (6)
                                                                                                  [23]

Copyright reserved                                                                 Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)     MECHANICAL TECHNOLOGY: WELDING AND METALWORK                       11

 QUESTION 6: TOOLS AND EQUIPMENT (SPECIFIC)

 6.1    State TWO uses of each of the following machines:

        6.1.1    Guillotine                                                              (2)

        6.1.2    Bench grinder                                                           (2)

        6.1.3    Press machine                                                           (2)

 6.2    FIGURE 6.2 below shows a joining equipment.

                                       FIGURE 6.2                                        (4)

        6.2.1    Label A–D.

        6.2.2    Identify the joining equipment shown in FIGURE 6.2 above.               (1)

Copyright reserved                                                           Please turn over

### Page 12

Downloaded from hlayiso.com
12          MECHANICAL TECHNOLOGY: WELDING AND METALWORK                     (EC/SEPTEMBER 2020)

 6.3      What is the function of stock and dies?

                                                                                             (1)

 6.4      What is the primary function of the regulator fitted to the gas cylinder of the
          oxy-acetylene equipment?                                                           (2)

 6.5      Explain the operating principle of plasma cutting machine that is used in a
          welding workshop.                                                                  (4)
                                                                                            [18]

Copyright reserved                                                             Please turn over

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)       MECHANICAL TECHNOLOGY: WELDING AND METALWORK                        13

 QUESTION 7: FORCES (SPECIFIC)

 7.1    Define the following terms:

        7.1.1    Force                                                                      (2)

        7.1.2    Hooke’s Law                                                                (2)

 7.2    A machinist is performing a tensile test using a mild steel bar with a diameter
        of 24 mm. An applied load of 60 kN cause an extension of 0,22 mm and the
        original length was 212 mm.

        Calculate the following:

        7.2.1    Stress in the mild steel bar                                               (2)

        7.2.2    Strain in the mild steel bar                                               (2)

        7.2.3    Young’s modulus of elasticity                                              (4)

 7.3    FIGURE 7.3 below is diagram of a beam with a UDL resting on the beam.
        The beam is supported at two ends.

                                          FIGURE 7.3

        Calculate the following for FIGURE 7.3:

        7.3.1        The magnitudes of RL and RR                                            (6)

        7.3.2        The bending moments at points A, B and C                               (3)

        7.3.3        Shear forces at points, A, B and C                                     (3)

        7.3.4        Draw a shear force diagram                                             (5)

        7.3.5        The bending moment diagram

                     NOTE:    Space diagram scale 1 : 100
                              Shear force diagram scale 2 mm =1 N
                              Bending moment diagram scale 2 mm = 1 N.m.                    (5)

Copyright reserved                                                              Please turn over

### Page 14

Downloaded from hlayiso.com
14          MECHANICAL TECHNOLOGY: WELDING AND METALWORK                      (EC/SEPTEMBER 2020)

 7.4      Construct the space and force diagram of the following steel frame structure in
          order to determine the magnitude and nature of the forces in each member of
          the framework.
          Space diagram 1 : 100
          Force diagram 1 mm = 1 kN

                                                          100 kN

                                  A                                       B

                                      60 ̊                         30 ̊
                     25 kN                                                          75 kN
                                                     C

                                                   7000

                              Member         Magnitude (KN)   Nature
                              AD
                              BD
                              CD
                                                                                                (11)
                                                                                               [45]

Copyright reserved                                                              Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)       MECHANICAL TECHNOLOGY: WELDING AND METALWORK                    15

 QUESTION 8: JOINING METHODS (INSPECTION WELD) (SPECIFIC)

 8.1      Name TWO things to be observed during oxy-acetylene or arc welding to
          ensure that weld defects are not formed.                                             (2)

 8.2      Describe TWO types of cracks in welded joints.                                       (4)

 8.3      Label the diagram in FIGURE 8.3.                                                     (5)

                                                 FIGURE 8.3

 8.4      State TWO elements that should be inspected during the visual inspection
          process.                                                                             (2)

 8.5      State TWO causes of each of the following arc-welding defects:

          8.5.1      Spatter / welding spatter                                                 (2)

          8.5.2      Incomplete penetration                                                    (2)

 8.6      Name TWO factors that should be observed to ensure a good welded joint
          during the arc-welding process.                                                      (2)

 8.7      Give ONE reason for performing the following destructive tests:

          8.7.1      Nick-break test

                                                                                               (2)

Copyright reserved                                                          Please turn over

### Page 16

Downloaded from hlayiso.com
16          MECHANICAL TECHNOLOGY: WELDING AND METALWORK                   (EC/SEPTEMBER 2020)

          8.7.2      Machinability test

                                                                                        (2)
                                                                                       [23]

 QUESTION 9: JOINING METHODS (STRESSES) (SPECIFIC)

 9.1      Define the following terms:

          9.1.1      Weld distortion                                                    (2)

          9.1.2      Residual stress                                                    (2)

 9.2      Give any TWO main factors affecting grain size of steel when being cold
          worked.                                                                       (2)

 9.3      State any TWO types of steel groups and name the percentage carbon
          content in each.                                                              (4)

 9.4      Name TWO types of quenching mediums.                                          (2)

 9.5      Discuss any TWO factors that affect shrinkage in welding.                     (2)

 9.6      Describe with the aid of a sketch/diagram the following terms:

          9.6.1      Transverse shrinkage                                               (2)

          9.6.2      Longitudinal shrinkage                                              (2)
                                                                                       [18]

 QUESTION 10: MAINTENANCE (SPECIFIC)

 10.1     What is the purpose of keeping service records of maintenance of
          machines in the workshop?                                                     (1)

 10.2     Give TWO reasons of locking out large machines before maintenance.            (2)

 10.3     How can friction be reduced when drilling holes?                              (1)

Copyright reserved                                                           Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)      MECHANICAL TECHNOLOGY: WELDING AND METALWORK                 17

 10.4     Explain how the following machines can be overloaded:

          10.4.1     Guillotine                                                        (2)

          10.4.2     Horizontal band saw                                               (2)
                                                                                       [8]

 QUESTION 11: TERMINOLOGY (DEVELOPMENT) (SPECIFIC)

 11.1     FIGURE 11.1 below shows a conical hopper.

                                           FIGURE 11.1

          Calculate the following:

          11.1.1     The true length DC                                                (5)

          11.1.2     The true length AD                                                (4)

          11.1.3     The base circumference of the hopper                              (3)

Copyright reserved                                                      Please turn over

### Page 18

Downloaded from hlayiso.com
18          MECHANICAL TECHNOLOGY: WELDING AND METALWORK                        (EC/SEPTEMBER 2020)

 11.2     FIGURE 11.2 below shows a square-to-round transition piece. In order to
          develop the transition, the true lengths must be calculated:

                                         FIGURE 11.2

          Determine the following true lengths with the help of calculations:

          11.2.1     True length FG                                                            (5)

          11.2.2     True length CI                                                           (4)
                                                                                             [21]

                                                                                TOTAL:        200

Copyright reserved                                                                Please turn over

### Page 19

Downloaded from hlayiso.com
(EC/SEPTEMBER 2020)       MECHANICAL TECHNOLOGY: WELDING AND METALWORK                 19

                     FORMULA SHEET FOR MECHANICAL TECHNOLOGY
                             (WELDING AND METALWORK)

1.     STRESS AND STRAIN

                  Force                             F
 1.1   Stress                      or         σ
                  Area                              A

                               Stress                         σ
 1.2    Young' s modulus                      or       E
                               Strain                         ε

                  Change in length                           Δl
 1.3   Strain                                 or       ε
                  Original length                            ol

2.     PYTHAGORAS' THEOREM AND TRIGONOMETRY

                                r
          y

                                           ϴ
                            x

                y
2.1    sin  
                r
                x
2.2     cos  
                r
                y
2.3     tan  
                x
2.4     r 2  x2  y2     or        a 2  b2  c2

3.     TEMPLATES AND DEVELOPMENTS

        Mean φ  Outside φ  Plate thickness            or
3.1
        Meanφ  Inside φ  Plate thickness

3.2     Mean circumfere nce  π  Mean φ

Copyright reserved                                                       Please turn over

## Related documents

- [MECH TECH GR12 QP SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept-2020-auto-english/5a5fe226-4c82-4735-bd84-25a08bed5162) — Mechanical Technology · QP · 2020 · Eng
- [MECH TECH GR12 MEMO SEPT 2020 Auto English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept-2020-auto-english/9066fed3-db75-4436-9ea3-0a432f99cc0b) — Mechanical Technology · Memo · 2020 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Mechanical Technology · Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Mechanical Technology · Memo · 2023 · Eng
- [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Mechanical Technology · Memo · 2023 · Eng
- [MT Nov 2020 (Automotive) Eng](https://www.hlayiso.com/library/mt-nov-2020-automotive-eng/489fabb7-3cad-4d15-965e-29f7af36ce41) — Mechanical Technology · QP · 2020 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng
- [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — QP · 2023 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
