# Mechanical Technology Grade 12 2018 Memo

> Grade 12 Mechanical Technology memorandum from the Fitting And Machining 2018, 18 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-memo-sept2018-engl/9a324c47-89e5-4628-81a3-6484b571ff6c
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2018
- Exam period: Fitting And Machining
- Curriculum: CAPS
- Pages: 18

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 2018 Memo](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-memo-sept2018-engl/9a324c47-89e5-4628-81a3-6484b571ff6c)

## About this document

Mechanical Technology · Grade 12 · Fitting and Machining · 2018. Memorandum, 18 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                        NATIONAL
                   SENIOR CERTIFICATE

                          GRADE 12

                    SEPTEMBER 2018

   MECHANICAL TECHNOLOGY: FITTING AND
               MACHINING
           MARKING GUIDELINE

MARKS:   200

               This marking guideline consists of 19 pages.

### Page 2

Downloaded from hlayiso.com
2                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)          (EC/SEPTEMBER 2018)

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS
 1.1    D✓                                                                                 (1)

 1.2    C✓                                                                                 (1)

 1.3    D✓                                                                                 (1)

 1.4    D✓                                                                                 (1)

 1.5    D✓                                                                                 (1)

 1.6    B✓                                                                                 (1)
                                                                                           [6]

 QUESTION 2: SAFETY
 2.1    Unsafe conditions:
        •  Working at unsafe speeds. 
        •  Grinding without goggles. 
        •  Fooling and playing around workshop. 
        •  Spilling liquids on floor. 
        •  Lubricating/cleaning moving parts. 
        •  Wearing loose clothing near moving parts. 
        •  Grinding on the side of the grinding wheel.                        (Any 4)     (4)

 2.2    Assessing a first aid situation:
        •  Environmental observation. 
        •  Visible signs and symptoms. 
        •  Indicators to diagnosis. 
        •  Vital functions. 
        •  Stopping any serious bleeding. 
        •  Immediate treatment of cardiac arrest.                             (Any 2)     (2)
        2.3.1    Advantages of product layout:
                 • Handling of material is limited to a minimum. 
                 • Time period of manufacturing cycle is less. 
                 • Production control is almost automatic. 
                 • Greater use of unskilled labour is possible. 
                 • Less total inspection is required. 
                 • Less total floor space is needed per unit of production.  (Any 2)      (2)
        2.3.2    Advantages of the process layout of machines
                 • High machine utilisation because more than one product is
                   manufactured. 
                 • Better supervision as a result of subdivision of processes. 
                 • Less interruption in flow of work when machines become
                   defective. 
                 • Lower equipment cost, since one machine can produce more
                   than one product. 
                 • Better control of total manufacturing cost. 
                 • Greater flexibility in the production process.             (Any 2)     (2)
                                                                                          [10]

Copyright reserved                                                             Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                     3

 QUESTION 3: MATERIALS

 3.1    Purpose of case-hardening.
        The objective is to produce a hard case over a tough core.                          (2)

 3.2    Factors of hardness.
        • Workpiece size. 
        • Quenching rate. 
        • Carbon content.                                                                    (3)

 3.3    Four kinds of quenching mediums.
        • Water and salt (brine) 
        • Tap water 
        • Liquid salts 
        • Molten lead 
        • Soluble oil and water 
        • Oil                                                                  (Any 4)       (4)

 3.4    Reason for hardened steel to be tempered:
        To reduce brittleness and to give the work piece a more fine-grained
        structure.                                                                           (2)

 3.5    Test on materials:

        Type of test           Mild Steel          High Speed Steel      Cast Iron
        Sound Test       Medium metallic sound    Low ring sound      Dull sound        (3)
                                                                                          [14]

 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

 4.1    C✓                                                                                    (1)

 4.2    C✓                                                                                    (1)

 4.3    A✓                                                                                    (1)

 4.4    B✓                                                                                    (1)

 4.5    A✓                                                                                    (1)

 4.6    A✓                                                                                    (1)

 4.7    C✓                                                                                    (1)

 4.8    D✓                                                                                    (1)

 4.9    B✓                                                                                    (1)

 4.10 A ✓                                                                                     (1)

 4.11 B ✓                                                                                     (1)

 4.12 C ✓                                                                                     (1)

Copyright reserved                                                         Please turn over

### Page 4

Downloaded from hlayiso.com
4                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)            (EC/SEPTEMBER 2018)

 4.13   D✓                                                                                   (1)

 4.14   B✓                                                                                   (1)
                                                                                            [14]

 QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)

 5.1    Tailstock set-over

        5.1.1                    𝐷−𝑑      𝐿𝑒𝑛𝑔𝑡ℎ 𝑊𝑜𝑟𝑘𝑝𝑖𝑒𝑐𝑒
                 𝑆𝑒𝑡 − 𝑜𝑣𝑒𝑟 =          × 𝐿𝑒𝑛𝑔𝑡ℎ 𝑜𝑓 𝑇𝑎𝑝𝑒𝑟 √
                                   2

                                 60−50     220
                             =           × 140 √
                                   2

                             = 7,857 mm √                                                    (3)

        5.1.2                                             𝜃    5
                                                    𝑇𝑎𝑛     =
                                                          2   140
                                          𝜃
                                               = 𝑡𝑎𝑛−1 0.0357   = 2.045 
                                           2

                                           = 4,1          √                                 (1)

 5.2    Lathe attachments:

        5.2.1    Lathe bed √                                                                 (1)

        5.2.2    Lathe carriage √                                                            (1)

 5.3    The pitch (P) of a screw thread is the distance from any point on the screw
        thread to a corresponding point on an adjacent (next) thread, measured
        parallel to the axis of the screw thread. √                                          (1)

 5.4    The reason for using a diving head on a milling machine is to divide the
        circumference of a circular object into any number of equal divisions. √             (1)

 5.5    Taper-turning procedure:

        •    The base of the compound slide or top of the cross slide comprises a
             circular plate that is marked off in degrees. √
        •    Loosen the base screws and set the compound slide to the desired
             angle. √
        •    Tighten the screws to lock it into position. √
        •    The tool should be set with its cutting point exactly level with the lathe’s
             centre line. √
        •    The carriage should always be locked to the lathe bed when cutting
             short tapers. √
        •    When the cutting action has started, use the compound slide handle to
             feed. √                                                          (Any 5 x 1)    (5)

Copyright reserved                                                               Please turn over

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)       MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                 5

 5.6 Square screw thread:

                                                     ✓                                        (5)
                                                                                             [18]

 QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)

 6.1   Gear calculations:
       6.1.1     Module of small gear:

                                     𝑃𝐶𝐷
                 𝑀𝑜𝑑𝑢𝑙𝑒 (𝑚) =
                                      𝑇
                                    87,75
                             m=             ✓
                                     39

                             m = 2,25 mm        ✓                                            (2)

       6.1.2     Module of Large gear:

                                     𝑃𝐶𝐷
                 𝑀𝑜𝑑𝑢𝑙𝑒 (𝑚) =
                                      𝑇
                               = 126/56 ✓

                               = 2,25 mm ✓                                                   (2)

       6.1.3     Outside Diameter of larger gear:

                 OD = PCD + 2m ✓

                 OD = 126 + (2 x 2,25)✓

                       = 130,50 mm ✓                                                         (3)

       6.1.4     Dedendum of large gear:

                 D = 1,157 x m                  OR       D = 1,25 x m

                      = 2,6 mm √√                         = 2,81 mm √√                       (2)

Copyright reserved                                                        Please turn over

### Page 6

Downloaded from hlayiso.com
6                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)          (EC/SEPTEMBER 2018)

       6.1.5     Clearance of gear system:

                 C = 0,157 x m                OR         C = 0,25 x m

                     = 0,35 mm √√                           = 0,56 mm √√                      (2)

       6.1.6     Indexing on the large gear:

                                    40
                       𝐼𝑛𝑑𝑒𝑥𝑖𝑛𝑔 =
                                    𝑛

                                 = 40/39✓
                                     1
                                 = 1 39   ✓

                 One turn of the crank handle, ✓ One hole, on a 39 hole plate ✓               (4)

 6.2   The index plate makes provision for diving a fraction of a turn accurately by
       means of holes spaced evenly on the pitch circle. ✓✓                                   (2)

Copyright reserved                                                             Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                       7

 6.3                            𝐴𝑛𝑔𝑙𝑒 𝑟𝑒𝑞𝑢𝑖𝑟𝑒𝑑 (𝑑𝑒𝑔𝑟𝑒𝑒𝑠)
       𝐴𝑛𝑔𝑢𝑙𝑎𝑟 𝐼𝑛𝑑𝑒𝑥𝑖𝑛𝑔 =
                                           9
                                 𝐴𝑛𝑔𝑙𝑒 𝑟𝑒𝑞𝑢𝑖𝑟𝑒𝑑 (𝑚𝑖𝑛𝑢𝑡𝑒𝑠)
       𝐴𝑛𝑔𝑢𝑙𝑎𝑟 𝐼𝑛𝑑𝑒𝑥𝑖𝑛𝑔, 𝑇 =
                                           540

                             = 61 20 ‘/9 ✓

                             = 3680/540
                                  44
                             = 6 54 ✓

       i.e. 6 complete turns of the crank and 44 holes in the 54 hole circle. ✓                  (3)

 6.4   Module is the ratio ✓ of pitch diameter to the number of the teeth, generally
       regarded as tooth size. ✓                                                                 (2)

 6.5   Dovetail Calculations:
            𝐷
       𝑅 = 2 = 10 𝑚𝑚✓

            𝜃
       𝛼 = 2 = 20°✓

                 𝑅
        tan 𝛼 = 𝑎 ✓

            X = 2a + 2R + 80 ✓

             X = (2 x 27,5) + (2 x 10) + 80 ✓

                = 154,95 mm ✓                                                                 (6)
                                                                                             [28]

Copyright reserved                                                            Please turn over

### Page 8

Downloaded from hlayiso.com
8                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)          (EC/SEPTEMBER 2018)

 QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

 7.1    Brinell Principle:

        The Brinell Hardness Test involves indenting ✓ the test material with a piece
        of 10 mm hardened steel or carbide ball, ✓subjected to a load of 3 000 kg.
        For softer materials, the load can be reduced to 1 500 kg or 500 kg to avoid
        excessive indentation. The full load is normally applied ✓ for 10 to 15 seconds
        in the case of iron and steel and for at least 30 seconds in the case of other
        metals. The diameter of the indentation left in the test material is measured
        with a low-powered microscope. ✓ 
        The Brinell Hardness Number is determined by dividing the load applied by
        the surface area of the indentation.                                               (4)

 7.2    Properties:

        • Yield strength √
        • Ultimate tensile strength √
        • Elongation percentage √                                          (Any 2 x 1)     (2)

 7.3    Pitch Diameter:

        Dp = Dn – (0,866 × Pitch)

            = 22 – (0,866 x 2,5) ✓

            =19,835 mm ✓                                                                   (2)

 7.4    Screw Thread Micrometer:

        The screw-thread micrometer is specifically designed to measure the pitch
        diameter of a screw thread. ✓✓                                                     (2)

 7.5    Depth Micrometer Reading:

                                                                         ✓✓✓               (3)
                                                                                          [13]

Copyright reserved                                                             Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                 9

 QUESTION 8: FORCES (SPECIFIC)

 8.1   Resultant Force Calculations:

                                                                                       (12)

Copyright reserved                                                      Please turn over

### Page 10

Downloaded from hlayiso.com
10                   MECHANICAL TECHNOLOGY (FITTING AND MACHINING)          (EC/SEPTEMBER 2018)

 8.2   Moments:

                                          FIGURE 8.2

       8.2.1    Define moment of force.
                • Moment of force is defined as force applied at a perpendicular
                  distance. √                                                                (1)

       8.2.2    Calculations, the magnitude of the reactions in support A and support
                B.

                Convert UDL to a point load: 60 N/m x 4,25 m = 255 N √

                Taking moments around A

                       (255 x 1,125) + (800 x 3,25) = (B x 7,75) + (350 x 8,75) ✓

                                     286,88 + 2600 = 7,758 + 350

                                                  B = 2536,88 ÷7,75 ✓

                                                  B = 327,34 N ✓

                Taking moments around B

                       (A x 7,75) = (800 x 4,5) + (255 x 6,625) + (350 x 8,75) ✓

                                 = 3600 + 1689,38 + 3062,5

                               A = 8351,88 ÷ 7,75 ✓

                               A = 1077,66 N ✓                                               (7)

       8.2.3    Beam applications:

                •    Bridges ✓
                •    Truss ✓
                •    Desks ✓
                •    Railway lines ✓
                                                                        (Any 2 x 1)    (2)

 8.3   Stress Calculations:

       8.3.1    Compressive Stress ✓                                                         (1)

Copyright reserved                                                             Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                11

       8.3.2    Stress in material:

                                    𝜋(𝐷 2 −𝑑2 )
                             A =                  ✓
                                         4
                                    𝜋(0,042 −0,032 )
                                =                      ✓
                                           4
                                = 0,55 x 10−3 𝑚2 ✓
                                     𝐹
                             𝜎 =
                                    𝐴
                                    23 𝑋 103
                               =                       ✓
                                    0,55 𝑋 103
                                = 41,84 MPa ✓                                              (5)

       8.3.3    Shortening of bush:

                                      𝜎
                             𝜀 =
                                      𝐸
                                     41,82 × 106
                                =                ✓
                                    90 × 109
                                = 0,46 X 10−3 ✓
                             ∆𝑙 = ol x E ✓
                                = 80 x (0,46 X 10−3) ✓
                                = 36,8 x 10−3 mm ✓                                      (5)
                                                                                       [33]

Copyright reserved                                                      Please turn over

### Page 12

Downloaded from hlayiso.com
12                   MECHANICAL TECHNOLOGY (FITTING AND MACHINING)             (EC/SEPTEMBER 2018)

 QUESTION 9: MAINTENANCE (SPECIFIC)

 9.1   Basic preventative maintenance:

       9.1.1    Gear systems:

                •    Checking and replenishment of lubrication levels. ✓
                •    Ensuring that gears are properly secured to shafts. ✓
                •    Cleaning and replenishment of oil filters. ✓
                •    Reporting excessive noise and wear, vibration and overheating
                     to be reported. ✓
                                                                    (Any 1)           (1)

       9.1.2    Belt drive systems check:

                •     For wear and tear on belt. ✓
                •     Belt alignment. ✓
                •     Tension setting. ✓
                •     The tensioning devices e.g. jockeys ✓            (Any 1)           (1)

       9.1.3    Chain drive systems:

                •    Cleaning uncovered chain drives. ✓
                •    Check sprocket teeth and link plate wear. ✓
                •    Refilling reservoir’s lubricants. ✓
                •    Checking the function of tensioning devices. ✓
                •    Inspect chains regularly for elongation and record the results. ✓
                                                                                     (Any 1)    (1)

 9.2   Reasons for using cutting fluid when working on the centre lathe:
       • It prevents the shavings or metal chips from sticking and fusing to the cutting
         tool. ✓
       • It will carry away the heat generated by the turning process.✓
       • It flushes away shavings/metal chips. ✓
       • It improves the quality of the finish of the turned surface. ✓     (Any 3 x 1)        (3)

 9.3   Pour point of a lubricant:
       • Is the lowest temperature at which a lubricant will cease to flow. ✓                   (1)

 9.4   • By applying a cutting fluid during the cutting action. ✓                               (1)

Copyright reserved                                                                Please turn over

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                        13

 9.5 TWO properties and TWO uses of each composites:

       Composite                Properties                        Uses
       9.5.1 Vesconite          - wear resistance ✓               - discs ✓
                                - very versatile ✓                - thrust washers ✓
                                - high load bearing strength ✓    - wear pads ✓
                                - high chemical resistance ✓      - vanes ✓
                                - very low co-efficient of        - light duty gears ✓
                                   friction ✓            (Any 2)                     (Any 2)       (4)
       9.5.2    Carbon Fibre    - light weight and low density✓ - sports equipment ✓
                                - good electrical conductivity ✓ - surf boards ✓
                                - easy to mould ✓                 - boat must ✓
                                - good damping properties ✓       - self-lubricating
                                - good friction and wear             gears ✓
                                   characteristics ✓              - artificial satellites ✓
                                                                  - helicopter blades ✓
                                                          (Any 2)                   (Any 2)        (4)

 9.6 The difference between static and sliding coefficient of friction:

       Static coefficient of friction is used for bodies without relative motion between
       them, ✓ while sliding coefficient of friction is used when there is relative motion
       between bodies. ✓

                                                OR

       Static coefficient is somewhat higher ✓ than kinetic or sliding coefficients. ✓              (2)
                                                                                                   [18]

Copyright reserved                                                              Please turn over

### Page 14

Downloaded from hlayiso.com
14                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)     (EC/SEPTEMBER 2018)

 QUESTION 10:          JOINING METHODS (SPECIFIC)

 10.1 Screw thread terminology:

        A        Crest/Outside/Normal/Major/Full/Basic diameter √
        B        Effective/Pitch diameter √
        C        Root/Core/Inside/Minor diameter √
        D        Angle (60°)/Thread angle √
        E        Crest √
        F        Root √
        G        Flank √                                                                      (7)

 10.2 Key and Keyway calculations:

        10.2.1                    𝐿𝑒𝑛𝑔𝑡ℎ 𝑜𝑓 𝑘𝑒𝑦
                     𝐷𝑖𝑎𝑚𝑒𝑡𝑒𝑟 =
                                       1,5

                              = 102/1,5 ✓

                              = 68 mm ✓                                                       (2)

        10.2.2                        𝐷𝑖𝑎𝑚𝑒𝑡𝑒𝑟
                     𝑊𝑖𝑑𝑡ℎ 𝑜𝑓 𝑘𝑒𝑦 =
                                         4
                                  = 68/4 ✓

                                  = 17 mm ✓                                                   (2)

        10.2.3                            𝐷𝑖𝑎𝑚𝑒𝑡𝑒𝑟
                     𝑇ℎ𝑖𝑐𝑘𝑛𝑒𝑠𝑠 𝑜𝑓 𝑘𝑒𝑦 =
                                             6

                                      = 68/6 ✓

                                      = 11,33 mm ✓                                            (2)

 10.3 Multi-start thread:
      - They provide more bearing surface than single start thread. ✓
      - They produce faster movement. ✓
      - They are more efficient as they lose less power to friction compared to single
        start screw threads. ✓                                             (Any 1 x 1)        (1)

 10.4 Screw Thread Cutting:

        10.4.1         Depth = 0,613 x Pitch ✓
                             = 0,613 x 1,5
                             = 0,92 mm ✓                                                      (1)

        10.4.2         Height = 0,866 x Pitch ✓
                             = 0,866 x 1,5
                             = 1,3 mm ✓                                                       (1)

Copyright reserved                                                         Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)     MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                15

 10.5     Uses of square thread:
          • Vice screws ✓
          • Motor jack ✓
          • Machine table screws ✓
          • Lead screw on centre lathes ✓
                                                        (Any 2 x 1)                (2)
                                                                                      [18]

Copyright reserved                                                      Please turn over

### Page 16

Downloaded from hlayiso.com
16                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)   (EC/SEPTEMBER 2018)

 QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)

 11.1    Use of gear drives in the industry:

         • Gears are suitable where space is limited. ✓
         • Gears are suitable where large amounts of power and torque must be
           transmitted. ✓
         • Where different machine speeds are required. ✓
         • Where change of rotational direction is required. ✓
                                                              (Any 2 x 1) (2)

 11.2    11.2.1      Calculate the diameter of Piston A.

                     First calculate the volume of cylinder B

                     𝑉𝐵 = 𝐴𝑟𝑒𝑎 𝐵 x 𝑆𝑡𝑟𝑜𝑘𝑒 𝑙𝑒𝑛𝑔𝑡ℎ𝐵
                             𝜋 𝑋 𝐷2
                         =            x 0,012
                               4
                         = 0,305 x 10−3 𝑚𝑚2 ✓

                                 But, 𝑉𝐴 = 𝑉𝐵
                               𝐴𝐴 x 𝐿𝐴 = 𝑉𝐵
                               𝐴𝐴 x 0,06 = 0,305 x 10−3
                                                 0,305 𝑥 10−3
                                         𝐴𝐴 =
                                                           0,06

                                            = 5,08 10−3 𝑚2 ✓

                                                𝜋𝐷𝐴2
                                         𝐴𝐴 =          
                                                  4
                                               5,08 𝑋 10−3 𝑋 4
                                         𝐷𝐴2 =                 ✓
                                                      𝜋

                                          𝐷𝐴 = √6,47 𝑋 10−3

                                                = 0,80 m

                                                = 80 mm ✓                               (4)

         11.2.2      Calculate the pressure exerted on Pistol A:

                                             𝐹
                     Pressure at A = 𝐴𝐴
                                                 𝐴

                                                     550
                                       𝑃𝐴 = 5,08 𝑋 10−3
                                          = 108,268 X 103 Pa ✓

                              = 108,27 kPa ✓                                       (2)

Copyright reserved                                                       Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2018)       MECHANICAL TECHNOLOGY (FITTING AND MACHINING)                    17

 11.3     Hydraulic pump and electrical motor work in a hydraulic system:

          The hydraulic pump, usually of the rotary gear type, is driven by an electric
          motor. ✓Electric energy from the pump is therefore converted into hydraulic
          energy ✓as the oil from the reservoir is admitted into the pump casing ✓ by
          suction and delivered at the outlet ✓ into the hydraulic circuit.                      (4)

 11.4     Functions of the pneumatic components:

          11.4.1 Air receiver
                 • After being compressed in a compressor, the air is stored in a
                    cylinder called air receiver. √                                              (1)

          11.4.2 Pipes
                 • Piping transports the fluid medium or air to all parts of the
                    pneumatic circuit where it is required.
                 • Piping ensures that the fluid velocity is constant and flow is
                    smooth. √                                                                    (1)

          11.4.3 Actuators
                 • Converts energy in the form of compressed air into mechanical
                   energy. √                                                                     (1)

 11.5     The belt-drive system calculations:

          11.5.1 The rotation frequency of the driven pulley in r/min:

                           N1 x D1 = N2 D2 ✓
                                  1440 𝑥 118
                           𝑁𝐼 =                ✓
                                      230

                           N1     = 738,78 rpm ✓                                                 (3)

          11.5.2 The belt speed of the system in metres per second

                      V = DN

                       =  x 0,118 x 24     ✓

                       = 8,90 m/s ✓                                                              (2)

Copyright reserved                                                            Please turn over

### Page 18

Downloaded from hlayiso.com
18                    MECHANICAL TECHNOLOGY (FITTING AND MACHINING)            (EC/SEPTEMBER 2018)

        11.6.1       Gear calculations:

                     Gear drive

                     Rotational frequency of the electric motor:

                     𝑁𝐴          𝑇𝐵 𝑋 𝑇𝐷
                           =                  ✓
                     𝑁𝐷          𝑇𝐴 𝑋 𝑇𝐶

                                80 𝑋 63 𝑋 2
                     𝑁𝐴 =                         ✓
                                    30 𝑋 40

                                10080
                            =              ✓
                                 1200

                              = 8,4 r/s ✓                                                        (4)

        11.6.2       Speed ratio of gear train:

                                               𝐈𝐧𝐩𝐮𝐭       𝐃𝐫𝐢𝐯𝐞𝐧 𝐭𝐞𝐞𝐭𝐡
                     Speed ratio = 𝐎𝐮𝐭𝐩𝐮𝐭 Speed ratio = 𝐃𝐫𝐢𝐯𝐞𝐫 𝐭𝐞𝐞𝐭𝐡

                          𝟖,𝟒                              𝟖𝟎   𝟔𝟑
                     =          ✓                  OR   = 𝟑𝟎 x 𝟒𝟎 ✓
                          𝟐

                     = 4,2 : 1 ✓                        = 4,2:1 ✓                                (2)

 11.7   Name TWO parts of a chain system.

         •   Rollers ✓
         •   Sprockets and spokes ✓
         •   Inner and Outer plate ✓
         •   Bushes ✓
         •   Bearing pins ✓                                              (Any 2 x 1)        (2)
                                                                                                [28]

                                                                                    TOTAL: 200

Copyright reserved                                                                Please turn over

## Related documents

- [MECHANICAL TECH (Fitting) GR12 MEMO SEPT2018 Eng D](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-memo-sept2018-eng-d/b81f28bc-38d4-4eb0-b71f-1ed49292bc8d) — Mechanical Technology · Memo · 2018 · Eng
- [MECHANICAL TECH (Fitting) GR12 MEMO SEPT2018 Afr D](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-memo-sept2018-afr-d/8d0d8d4b-92ad-4dbd-880d-f8121236a2a1) — Mechanical Technology · Memo · 2018 · Afr
- [MECHANICAL TECH (Fitting) GR12 MEMO SEPT2018 Afr](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-memo-sept2018-afr/1f4ee081-b7fa-4cb3-b5f7-0b236ad33db1) — Mechanical Technology · Memo · 2018 · Afr
- [MECHANICAL TECH (Fitting) GR12 QP SEPT2018 Afr D](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-qp-sept2018-afr-d/96fd3005-cc60-42f8-b858-b415738175ed) — Mechanical Technology · QP · 2018 · Afr
- [MECHANICAL TECH (Fitting) GR12 QP SEPT2018 Eng D](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-qp-sept2018-eng-d/b74e67a7-d946-4db5-bbe9-6d4b6364fe71) — Mechanical Technology · QP · 2018 · Eng
- [MECHANICAL TECH (Fitting) GR12 QP SEPT2018 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-qp-sept2018-afrikaans/f267a2fe-bb93-4858-93e7-70d27c2f390f) — Mechanical Technology · QP · 2018 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — QP · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-afrikaans/f45c553c-63a1-4e1c-b9c6-d426a3dfef26) — Memo · 2023 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
