# Mechanical Technology Grade 12 NSC Supplementary 2018 QP

> Grade 12 Mechanical Technology question paper from the NSC Supplementary Exam 2018 (English), 17 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-feb-march-2018-eng/4240af0f-86fd-4c37-bd71-a5c4c769b35e
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2018
- Exam period: NSC Supplementary Exam
- Curriculum: CAPS
- Pages: 17

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC Supplementary 2018 QP](https://www.hlayiso.com/library/mechanical-technology-feb-march-2018-eng/4240af0f-86fd-4c37-bd71-a5c4c769b35e)

## About this document

Mechanical Technology · Grade 12 · NSC Supplementary Exam · 2018. Question paper, 17 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

                         MECHANICAL TECHNOLOGY

                            FEBRUARY/MARCH 2018

 MARKS: 200

 TIME: 3 hours

        This question paper consists of 13 pages and a 4-page formula sheet.

Copyright reserved                                                   Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology                          2                          DBE/Feb.–Mar. 2018
                                              NSC

INSTRUCTIONS AND INFORMATION

1.        This question paper consists of TEN questions.

2.        Read ALL the questions carefully.

3.        Answer ALL the questions.

4.        Number the answers correctly according to the numbering system used in this
          question paper.

5.        Start EACH question on a NEW page.

6.        Show ALL calculations and units. Round off ALL answers to TWO decimal
          places.

7.        Candidates may use non-programmable, scientific calculators and drawing
          instruments.

8.        Take the value of gravitational force as 10 m/s-2.

9.        All dimensions are in millimetres, unless stated otherwise in the question.

10.       A formula sheet for your use is attached to this question paper.

11.       Write neatly and legibly.

12.       Use the guidelines below to assist you in managing your time.

                                                                               TIME
          QUESTION                CONTENT                      MARKS
                                                                             (minutes)
                1        Multiple-choice questions               20              15
                2        Safety                                  10              10
                3        Tools and Equipment                     12              10
                4        Materials                               13              10
                5        Terminology                             30              20
                6        Joining Methods                         25              25
                7        Forces                                  30              30
                8        Maintenance                             15              15
                9        Systems and Control                     25              25
               10        Turbines                                20              20
                                              TOTAL             200             180

Copyright reserved                                                            Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology                         3                            DBE/Feb.–Mar. 2018
                                             NSC

QUESTION 1: MULTIPLE-CHOICE QUESTIONS

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question number (1.1–1.20) in
the ANSWER BOOK, for example 1.21 D.

1.1       FIGURE 1.1 shows one of the steps to remove and replace bearings.
          Which safety procedure is indicated in FIGURE 1.1?

                                           FIGURE 1.1

          A     Remove the dolly by tapping it with a hammer.
          B     Remove the burrs from the shaft to prevent damage to the dolly.
          C     Place the driving dolly against the inner ring of the bearing and tap the
                dolly with a hammer.
          D     Slacken the lock nut by tapping it lightly with a hammer.                         (1)

1.2       Which ONE of the following safety procedures applies to the maintenance of
          a hydraulic press?

          A     Do not apply a wrench to a revolving part.
          B     Guards could be removed when pressing soft material.
          C     Pressure gauges must be tested regularly and adjusted or replaced if
                any malfunction occurs.
          D     Use the machine table as an anvil.                                                (1)

1.3       The function of a valve-spring tester is to test the valve spring for … and
          squareness before fitting.

          A     twisting
          B     tension
          C     shearing
          D     deflection                                                                        (1)

1.4       What is the function of a depth micrometer?

         A     Measures the outside diameter of a workpiece accurately
         B     Measures the inside diameter of a hole in a work piece accurately
         C     Measures the pitch diameter of a screw thread accurately
         D     Measures the depth of a hole in a workpiece accurately                             (1)

Copyright reserved                                                             Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology                         4                           DBE/Feb.–Mar. 2018
                                             NSC

1.5       Which structure of steel is characterised as intensely hard and brittle?

          A     Ferrite
          B     Pearlite
          C     Cementite
          D     Austenite                                                                         (1)

1.6       Which ONE of the following mechanical properties of steel represents
          resistance to shock loads?

          A     Brittleness
          B     Toughness
          C     Hardness
          D     Elasticity                                                                        (1)

1.7       What is the included angle of a metric V-screw thread?

          A     60°
          B     45°
          C     55°
          D     29°                                                                               (1)

1.8       What is a disadvantage of down-cut milling?

          A     The cutter blunts rapidly when it is used to cut material with surface
                scale on it.
          B     It can cut through thin pipes and tubes.
          C     A better finish is produced.
          D     The coolant is carried down to the teeth where it is required.                    (1)

1.9       Which ONE of the following tests uses sound waves to penetrate a test
          piece?

          A     Ultrasonic test
          B     X-ray test
          C     Dye penetration test
          D     Nick-break test                                                                   (1)

1.10      Which ONE of the following is the cause of undercutting during the welding
          process?

          A     Rapid chilling
          B     Current too high
          C     Slag not removed from the previous run weld
          D     Dirty or wet weld electrode                                                       (1)

Copyright reserved                                                             Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology                         5                      DBE/Feb.–Mar. 2018
                                             NSC

1.11      Which ONE of the following statements defines strain in a material?
          Strain is the ratio between the …

          A     change in length and the original length.
          B     change in diameter and the original length.
          C     total length and the original length.
          D     change in stress and the original stress.                                 (1)

1.12      Refer to FIGURE 1.12 below. What type of stress, caused by force F, will
          occur in the bolt of the joint?

                                                   F

                                                   F
                                          FIGURE 1.12

          A     Tensile stress
          B     Compressive stress
          C     Shearing stress
          D     Compression stress                                                        (1)

1.13      What is the unit measure for moments?

          A     N/m
          B     N.m
          C     N.m2
          D     N.m-2                                                                     (1)

1.14      What is understood by the term viscosity regarding liquids? It is the
          resistance to …

          A     flow.
          B     boiling.
          C     cooling.
          D     foaming.                                                                  (1)

1.15      Where will you use EP 90 oil?

          A     Engines
          B     Power steering
          C     Brakes
          D     Gearbox                                                                   (1)

Copyright reserved                                                       Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology                         6                           DBE/Feb.–Mar. 2018
                                             NSC

1.16      FIGURE 1.16 below represents a hydraulic system. What is the comparison
          between the fluid pressure at piston A and the fluid pressure at piston B?

                                    A                  B

                                          FIGURE 1.16
          A     The pressure at piston A is the same as the pressure at piston B.
          B     The pressure at piston A is more than the pressure at piston B.
          C     The pressure at piston A is less than the pressure at piston B.
          D     The pressure at piston A is double the pressure at piston B.                   (1)
1.17      Which ONE of the following statements defines Boyle's law?
          A     An ideal gas law where, at constant pressure, the volume of an ideal
                gas is inversely proportional to its absolute temperature.
          B     An ideal gas law where, at constant volume, the temperature of an
                ideal gas is inversely proportional to its absolute pressure.
          C     An ideal gas law where, at constant temperature, the volume of an
                ideal gas is inversely proportional to its absolute pressure.
          D     An ideal gas law where, at constant temperature, the volume of an
                ideal gas is proportional to its absolute pressure.                              (1)
1.18      What will the velocity ratio of a belt drive system be if the driven pulley
          rotates at 1 000 r/min and the driver pulley at 100 r/min?
          A     1 : 10
          B     10 : 1
          C     1 : 100
          D     100 : 1                                                                          (1)
1.19      A steam turbine is used to …
          A     increase the fuel consumption in relation to engine output.
          B     drive a generator to generate electricity.
          C     increase the volumetric efficiency of an engine.
          D     increase atmospheric pressure in an engine.                                    (1)
1.20      The advantage of a turbocharger compared to a supercharger is that it
          uses … to drive it.
          A     exhaust gases
          B     power from the engine
          C     a belt
          D     a fuel/air mixture                                                             (1)
                                                                                               [20]
Copyright reserved                                                            Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology                            7                        DBE/Feb.–Mar. 2018
                                                NSC

QUESTION 2: SAFETY

2.1       When assembling a cylinder head of a motor vehicle's engine, the valve
          springs must be tested before installation. State TWO safety precautions
          you should observe when working with the spring tester.                              (2)

2.2       Why is it important to wear an arc welding helmet during arc welding?                (1)

2.3       Why is it important to keep the copper electrodes of a spot welder cool
          during operation?                                                                    (1)

2.4       Name ONE distinct safety precaution when using EACH of the following
          items of testing equipment:

          2.4.1       Brinell hardness tester                                                  (1)

          2.4.2       Tensile tester                                                           (1)

          2.4.3       Torsion tester                                                           (1)

2.5       At what angle to the bearing should a bearing puller be used?                        (1)

2.6       The following safety measures apply when using a cylinder leakage tester.
          Name ONE reason why you have to adhere to the following safety
          measures:

          2.6.1       Do not exceed the prescribed pressure in the cylinder.                   (1)

          2.6.2       The tester should be fitted properly in the spark plug hole or
                      injector hole.                                                           (1)
                                                                                               [10]

QUESTION 3: TOOLS AND EQUIPMENT

3.1       Tools and equipment are very important to complete different tasks in the
          workplace. Explain the function of EACH of the following testing equipment:

          3.1.1       Cylinder compression tester                                              (2)

          3.1.2       Fuel pressure tester                                                     (2)

          3.1.3       Torsion tester                                                           (2)

3.2       The   gas   analyser     is  used    to  determine the    CO   and
          CO2 readings of the exhaust gases of an internal combustion engine.
          Give TWO reasons for a high CO2 reading.                                             (2)

3.3       Most welding companies use MIG/MAGS welding equipment for their
          welding.

          3.3.1       Give TWO reasons for using inert gas during MIG/MAGS
                      welding.                                                                 (2)

          3.3.2       State TWO advantages of the use of MIG/MAGS welding rather
                      than arc welding.                                                        (2)
                                                                                                [12]
Copyright reserved                                                             Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology                           8                       DBE/Feb.–Mar. 2018
                                               NSC

QUESTION 4: MATERIALS

4.1       Temperature affects the structure of steel with regard to the iron-carbon
          content. State TWO characteristics of each of the following:
          4.1.1       Austenite                                                                 (2)
          4.1.2       Ferrite                                                                   (2)

4.2       Explain what happens at the following critical points in the iron-carbon
          equilibrium diagram:
          4.2.1       Lower critical point (AC1)                                                (2)
          4.2.2       Higher critical point (AC3)                                               (2)

4.3       Give TWO reasons for enhancing the properties of the material used for
          a crankshaft.                                                                      (2)

4.4       Give TWO reasons for tempering a camshaft.                                         (2)

4.5       Which heat treatment process is used on piston rings?                              (1)
                                                                                             [13]
QUESTION 5: TERMINOLOGY
5.1       A parallel key must be machined to fit onto a 120 mm diameter shaft.
          Calculate the following:
          5.1.1       The width of the key                                                      (2)
          5.1.2       The thickness of the key                                                  (2)
          5.1.3       The length of the key                                                     (2)

5.2       A spur gear with 124 teeth must be cut on a universal milling machine.
          Calculate the simple indexing to cut this gear with the help of a Cincinnati
          dividing head.                                                                        (3)
5.3       The pitch of a metric V-screw thread is 3 mm. Calculate the height of the
          thread.                                                                               (2)
5.4       A spur gear has 48 teeth and a module of 3. Calculate the following:
          5.4.1       Addendum                                                                  (1)
          5.4.2       Dedendum                                                                  (2)
          5.4.3       Clearance                                                                 (2)
          5.4.4       Pitch circle diameter                                                     (2)
          5.4.5       Outside diameter                                                          (2)
          5.4.6       Cutting depth                                                             (2)
          5.4.7       Circular pitch                                                            (2)

Copyright reserved                                                           Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology                           9                        DBE/Feb.–Mar. 2018
                                               NSC

5.5       A metric V-screw thread needs to be cut on a centre lathe by setting the
          compound slide to half the included angle of the thread. The workpiece has
          been turned down to the required diameter and prepared to the necessary
          requirements. State the required settings to the lathe and cutting tool to
          enable you to cut the screw thread.                                                   (6)
                                                                                                [30]

QUESTION 6: JOINING METHODS

6.1       Name TWO causes of EACH of the following welding defects:

          6.1.1       Slag inclusion                                                            (2)

          6.1.2       Incomplete penetration                                                    (2)

6.2       Name TWO causes of atmospheric contamination during MIG/MAGS
          welding.                                                                              (2)

6.3       Explain the procedure to perform a nick-break test on a welded joint.                 (5)

6.4       Give ONE reason for performing the following destructive tests:

          6.4.1       Bend test                                                                 (2)

          6.4.2       Machinability test                                                        (2)

6.5       Give ONE reason of conducting an X-ray test on a welding joint.                       (2)

6.6       Define the term weld crater.                                                          (2)

6.7       Study FIGURE 6.7 below.

                                           FIGURE 6.7

          6.7.1       Identify the welding process in FIGURE 6.7.                               (1)

          6.7.2       Label parts A–E in FIGURE 6.7.                                          (5)
                                                                                              [25]
Copyright reserved                                                           Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology                           10                          DBE/Feb.–Mar. 2018
                                               NSC

QUESTION 7: FORCES

7.1       Four forces are acting on the same point. Determine, by means of
          calculations, the magnitude and direction of the resultant force for the
          system of forces in FIGURE 7.1 below.

                                             FIGURE 7.1                                              (13)

7.2       A compressive force of 20 kN is applied to a mild steel bush. The outer
          diameter is 56 mm and the inner diameter is 38 mm. The original length of
          the bush was 50 mm.

          Calculate:

          7.2.1        The resistance area of the bush                                              (2)

          7.2.2        The stress in the material                                                   (3)

          7.2.3        The strain if the final length of the bush is 49,975 mm                      (3)

          7.2.4        Young's modulus of elasticity for the material                               (3)

7.3       FIGURE 7.3 below shows a uniform beam, which is 6 m long, that is
          supported by two vertical supports, A and B. A uniformly distributed force of
          100 N/m is exerted on the left-hand side of the beam between the two point
          loads of 600 N and 850 N. Determine, by means of calculations, the
          magnitudes of the reactions in supports A and B.

              600 N                                 850 N
                         100 N/m

                                  3m                               3m
                  A                                                                 B

                                             FIGURE 7.3                                               (6)
                                                                                                     [30]
Copyright reserved                                                               Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology                          11                          DBE/Feb.–Mar. 2018
                                              NSC

QUESTION 8: MAINTENANCE

8.1       What is the reason for using SAE20W50 viscosity oil or other multigrade oil
          in an internal combustion engine?                                                       (2)

8.2       State TWO procedures to maintain V-belt drive systems.                                  (2)

8.3       Define the term flashpoint of a lubricant.                                              (3)

8.4       State TWO aspects to adhere to when taking care of cutting fluid used on
          a lathe.                                                                                (2)

8.5       State TWO functions of the clutch plate.                                                (2)

8.6       Give TWO reasons for skimming the flywheel before installing a new clutch
          plate.                                                                                  (2)

8.7       Give TWO properties of grease.                                                         (2)
                                                                                                [15]

QUESTION 9: SYSTEMS AND CONTROL

9.1       FIGURE 9.1 below shows a gear-drive system. Driver gear A on the shaft of
          the electric motor has 20 teeth that mesh with gear B with 36 teeth on a
          counter shaft. On the counter shaft is another driver gear, C, with 18 teeth
          that mesh with gear D with 46 teeth. The second counter shaft has driver
          gear E with 42 teeth, which drives gear F with 80 teeth on the output shaft.

           Electrical
                                               D                  E
           motor           A
                           20                  46                42
                                                       Counter
                                                        shaft
                           B
                           36                  C
                                               18                 F
                                 Counter
                                  shaft
                                                                 80      Output
                                                                          shaft

                                           FIGURE 9.1

         Calculate the:

         9.1.1       Rotation frequency of the input shaft on the electric motor if the
                     output shaft rotates at 160 r/min                                            (3)

         9.1.2       Velocity ratio between the input and output shaft                            (2)

Copyright reserved                                                             Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology                             12                            DBE/Feb.–Mar. 2018
                                                 NSC

9.2       FIGURE 9.2 below shows a belt drive system. The pulley, with a diameter
          of 0,24 m, drives the driven pulley with a diameter of 0,36 m. The driven
          pulley rotates at 733,33 r/min. T1 = 360 N and T2 = 90 N.

           NDN= 733,33 r/min                                         NDR= ? r/min
           DDN = 0,36 m                              T2              DDR = 0,24 m

                                                           T1
                                               FIGURE 9.2

         Calculate the:

         9.2.1          Rotation frequency of the driver pulley in r/min (revolutions per
                        minute)                                                                        (3)

         9.2.2          Power transmitted                                                              (2)

         9.2.3          Belt speed of the system in m.s-1 (metres per second)                          (2)

9.3       A hydraulic system is used to lift a machine. The specifications of the system
          are presented diagrammatically in FIGURE 9.3 below.

                 Ø 40 mm
                                                                         Ø ? mm
                      275 N

                                                                   Load = 5,56 kN

                     Piston A

                                                                         Piston B

                                               FIGURE 9.3

         Calculate the:

         9.3.1          Fluid pressure in the hydraulic system when in equilibrium                     (5)

         9.3.2          Diameter of piston B to lift a load of 5,56 kN                                 (4)

Copyright reserved                                                                  Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology                         13                            DBE/Feb.–Mar. 2018
                                             NSC

9.4       What is the purpose of the anti-lock brake system (ABS) in a vehicle?                  (2)

9.5       What does the abbreviation ECU stand for in terms of motor vehicles?                   (1)

9.6       State ONE advantage of a traction control system in a motor vehicle.                   (1)
                                                                                                 [25]

QUESTION 10: TURBINES

10.1      Name TWO types of reaction turbines.                                                   (2)

10.2      Explain the term boost in terms of superchargers.                                      (2)

10.3      Name TWO types of blowers used as superchargers on a motor vehicle's
          engine.                                                                                (2)

10.4      A gas turbine that is used as a jet engine is shown in FIGURE 10.4.
          Label A–F.

                        A           B                    C              D

                                                     F
                                                              E
                                           FIGURE 10.4                                           (6)

10.5      State TWO applications of a gas turbine.                                               (2)

10.6      State TWO advantages of a gas turbine.                                                 (2)

10.7      What is the purpose of the waste gate in a turbocharger?                               (2)

10.8      Why is an engine with a turbocharger fitted with an oil cooler?                        (2)
                                                                                                 [20]

                                                                                   TOTAL:        200

Copyright reserved

### Page 14

Downloaded from hlayiso.com
Mechanical Technology                               4                                     DBE/Feb.–Mar. 2018
                                                   NSC

                                            FORMULA SHEET

1.      BELT DRIVES

         1.1    N dr  D dr  N dn  D dn

                                πDN
         1.2    Belt speed                 where N is in r/min
                                 60

                                π ( D  t ) N
         1.3    Belt speed                    (t  belt thickness)
                                      60

         1.4    Belt mass = area × length × density (A = thickness × width)

                                 diameter of driven pulley
         1.5    Speed ratio 
                                 diameter of driver pulley

         1.6    Belt length (flat belt) = [(D + d) × 1,57] + 2 × centre distance

                                   π( D  d ) 2 ( D  d ) 2
         1.7    Open-belt length                           2c
                                       2            4c

                                      π( D  d ) 2 ( D  d ) 2
         1.8    Crossed-belt length                           2c
                                          2           4c

                                                      T1
         1.9    Ratio of tight side to slack side 
                                                      T2

                                (T1  T2 ) π D N
        1.10    Power (P)                       where N is in r/min
                                       60
                                                      T1  force in the tight side
                                                           T2  force in the slack side
                                                           T1  T2  effective force (Te )

         1.11   Power (P)  (T1  T2 )  V        where V  belt speed in m/s

                                 2πNT
         1.12   Power ( P )                      where N is in r/min
                                  60

                                         T1
         1.13   Width 
                              permissible tensile force

Copyright reserved                                                                            Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology                                     2         DBE/Feb.–Mar. 2018
                                                         NSC

2.      STRESS AND STRAIN

                           force                 F
         2.1    Stress             or ( σ        )
                            area                 A

                                 change in length ( ΔL )
         2.2    Strain ( ε ) 
                                   original length ( L )

                                                 stress     σ
         2.3    Young' s mod ulus ( E )                or ( )
                                                 strain     ε

                                                  πd 2
         2.4    Area of a round bar = A =
                                                   4

         2.5    Area of a pipe = A =
                                            
                                          π D2  d 2     
                                              4

         2.6    Area of a square bar = A = L2 or A = L × B

3.      HYDRAULICS

                                   force ( F )
         3.1    Pressure ( P ) 
                                   area ( A )

         3.2    Volume = (cross-sectional area) × stroke length

         3.3    Work done = force × distance

4.      KEYS AND KEYWAYS

                                   diameter of shaft
         4.1    Width of key 
                                          4

                                         diameter of shaft
         4.2    Thickness of key 
                                                6

         4.3    Length of key  1,5  diameter of shaft

         4.4    Standard taper for taper key: 1 in 100 or 1 : 100

Copyright reserved                                                      Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology                                 3                              DBE/Feb.–Mar. 2018
                                                     NSC

5.      LEVERS

                                                    load (W)
         5.1    Mechanical advantage (MA)
                                                    effort (F)

                                     input movement
         5.2    Velocity ratio 
                                     output movement

         5.3    Input movement (IM) = effort × distance moved by effort

         5.4    Output movement (OM) = load × distance moved by load

6.      GEAR DRIVES

         6.1    N dr  D dr  N dn  D dn

                                    2πNT
         6.2    Power ( P ) 
                                     60

                                  product of the number of teeth on the driven gears
         6.3    Gear ratio =
                                  product of the number of teeth on the driver gears

                 N input       product of the number of teeth on the driven gears
         6.4               
                N output       product of the number of teeth on the driver gears

         6.5    Torque = force × radius

         6.6    Torque transmitted = gear ratio × input torque

                                     pitch-circle diameter (PCD)
         6.7    Module (m) 
                                         number of teeth (T)

         6.8    N1T1  N 2 T2

                                                        circular pitch (CP)  number of teeth (T)
         6.9    Pitch-circle diameter (PCD) 
                                                                             

         6.10   Pitch-circle diameter (PCD)  m  T

         6.11   Outside diameter (OD)  m(T  2)

         6.12   Outside diameter (OD) = pitch-circle diameter (PCD) + 2 module

         6.13   Addendum = module (m)

         6.14   Dedendum = 1,157 m                 or        Dedendum = 1,25 m

Copyright reserved                                                                        Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology                              4                              DBE/Feb.–Mar. 2018
                                                  NSC

         6.15   Cutting depth = 2,157 m       or        Cutting depth = 2,25 m

         6.16   Clearance = 0,157 m           or        Clearance = 0,25 m

         6.17   Circular pitch (CP) = m × 

                                                            (PCD)A (PCD)B
         6.18   Centre distance between gear A and B             
                                                               2      2

7.      SCREW THREADS

        7.1     Pitch diameter = outside diameter – ½pitch

        7.2     Pitch circumference =  × pitch diameter

        7.3     Lead = pitch × number of starts

        7.4     Height of screw thread = 0,866 × pitch

        7.5     Depth of screw thread = 0,613 × pitch

8.      INDEXING

        8.1     Cincinnati dividing head table for milling machine

                                          Cincinnati Index Plates
           Side 1     24      25    28     30       34      37     38        39    41     42     43
           Side 2     46      47    49     51       53      54     57        58    59     62     66

                             40
        8.2     Indexing       (where n  number of divisions)
                             n

Copyright reserved

## Related documents

- [Mechanical Technology Feb March 2018 Afr](https://www.hlayiso.com/library/mechanical-technology-feb-march-2018-afr/5df7faf2-277f-4e96-b58e-b30ebda77666) — Mechanical Technology · QP · 2018 · Afr
- [Mechanical Technology Feb March 2018 Memo Afr](https://www.hlayiso.com/library/mechanical-technology-feb-march-2018-memo-afr/ff38a98a-516d-4d26-b5de-3f8554214a35) — Mechanical Technology · Memo · 2018 · Afr
- [MECHANICAL TECH (Auto) QP SEPT 2018 Eng D](https://www.hlayiso.com/library/mechanical-tech-auto-qp-sept-2018-eng-d/83d208e4-1aa5-489e-a101-c36d34d667bf) — Mechanical Technology · QP · 2018 · Eng
- [MECHANICAL TECH (Auto) QP SEPT 2018 Afr D](https://www.hlayiso.com/library/mechanical-tech-auto-qp-sept-2018-afr-d/afa4bb7e-c1c0-43a2-b25a-d37b36790118) — Mechanical Technology · QP · 2018 · Afr
- [MECHANICAL TECH (Auto) QP SEPT 2018 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-qp-sept-2018-afrikaans/605f9186-b7d4-4097-9164-d0ec93617dc4) — Mechanical Technology · QP · 2018 · Afr
- [MECHANICAL TECH (Fitting) GR12 QP SEPT2018 Afr D](https://www.hlayiso.com/library/mechanical-tech-fitting-gr12-qp-sept2018-afr-d/96fd3005-cc60-42f8-b858-b415738175ed) — Mechanical Technology · QP · 2018 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
