# Mechanical Technology Grade 12 NSC June 2023 QP (Eng)

> Grade 12 Mechanical Technology question paper from the NSC June Exam 2023 (English), 19 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-eng/1523a16f-2012-4f13-a922-86cbb5900666
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2023
- Exam period: NSC June Exam
- Curriculum: CAPS
- Pages: 19

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC June 2023 QP (Eng)](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-eng/1523a16f-2012-4f13-a922-86cbb5900666)

## About this document

Mechanical Technology · Grade 12 · NSC June Exam · 2023. Question paper, 19 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

               SENIOR CERTIFICATE EXAMINATIONS/
             NATIONAL SENIOR CERTIFICATE EXAMINATIONS

                     MECHANICAL TECHNOLOGY: AUTOMOTIVE

                                        2023

                                                                      MARKS: 200

                                                                    TIME: 3 hours

        This question paper consists of 17 pages and a 2-page formula sheet.

Copyright reserved                                                    Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Automotive              2                                         DBE/2023
                                            SC/NSC

INSTRUCTIONS AND INFORMATION

1.         Write your centre number and examination number in the spaces provided on
           the ANSWER BOOK.

2.         Read ALL the questions carefully.

3.         Answer ALL the questions.

4.         Number the answers correctly according to the numbering system used in this
           question paper.

5.         Start EACH question on a NEW page.

6.         Show ALL calculations and units. Round off final answers to TWO decimal
           places.

7.         Candidates may use non-programmable scientific calculators and drawing
           instruments.

8.         The value of gravitational acceleration should be taken as 10 m/s 2.

9.         All dimensions are in millimetres, unless stated otherwise in the question.

10.        Write neatly and legibly.

11.        A formula sheet is attached at the end of the question paper.

12.        Use the criteria below to assist you in managing your time.

                                                                                     TIME
QUESTION                            CONTENT                       MARKS
                                                                                  IN MINUTES
                                 GENERIC
      1         Multiple-choice Questions                            6                  6
      2         Safety                                               10                10
      3         Materials                                            14                14
                                 SPECIFIC
      4         Multiple-choice Questions                            14                10
      5         Tools and Equipment                                  23                20
      6         Engines                                              28                25
      7         Forces                                               32                25
      8         Maintenance                                          23                20
      9         Systems and Control (Automatic Gearbox)              18                20
                Systems and Control (Axles, Steering
      10                                                             32                30
                Geometry and Electronic)
                                                    TOTAL           200               180

Copyright reserved                                                                Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Automotive             3                                 DBE/2023
                                           SC/NSC

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)
Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E.
1.1      Which ONE of the following safety precautions is applicable to the bench
         grinder?
         A     Oil the surface of the machine.
         B     Remove all guards when grinding.
         C     Wear safety goggles when grinding.
         D     Ensure that the machine is on.                                                (1)
1.2      What does the Occupational Health and Safety Act state regarding HIV/Aids
         awareness?
         A     All employers must make sure that the workplace is safe, and that
               employees are not at risk of contracting HIV.
         B     It does not contain common guidelines on how employers, employees
               and trade unions should respond to persons with HIV in the workplace.
         C     Employers may demote or promote an employee based on his/her
               HIV status.
         D     Employers can simply dismiss a person who has HIV.                            (1)
1.3      Which ONE of the following procedures is applicable when applying basic
         medical treatment?
         A     Examine the injured person.
         B     Remove the object from the wound.
         C     Use an oily substance or lotion on a burn.
         D     Phone the insurance company.                                                  (1)
1.4      Why is steel heated slowly to a certain temperature during heat treatments?
         To ensure that …
         A     high heat is obtained.
         B     the room temperature is correct.
         C     a uniform temperature is obtained.
         D     the safety process is correct.                                                (1)
1.5      Which ONE of the following is an example of case-hardening?
         A     Frying pans
         B     Gears
         C     Wheel rims
         D     Chisels                                                                       (1)
1.6      What does the term quenching rate during heat treatment mean?
         A     Cooling rate
         B     Heating rate
         C     Tempering rate
         D     Hardening rate                                                                (1)
                                                                                             [6]

Copyright reserved                                                        Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Automotive           4                                        DBE/2023
                                         SC/NSC

QUESTION 2: SAFETY (GENERIC)

2.1      Which safety precaution must be adhered to after the work on any machine is
         completed?                                                                               (1)

2.2      Give TWO reasons why the space between the tool rest and the grinding
         wheel on a bench grinder must not exceed 3 mm.                                           (2)

2.3      Identify the workshop layouts shown in FIGURES 2.3.1 and 2.3.2 below.

         2.3.1

                                              FIGURE 2.3.1                                        (1)

         2.3.2

                                              FIGURE 2.3.2                                        (1)

2.4      State ONE type of personal protective equipment that must be worn when
         working on a hydraulic press machine.                                                    (1)

2.5      State ONE function of the safety guard on a portable angle grinder.                      (1)

2.6      State ONE safety precaution, other than environmental safety, that must be
         observed when using a shearing machine/guillotine.                                       (1)

2.7      State TWO safety precautions that must be adhered to when storing
         gas cylinders.                                                                           (2)
                                                                                                  [10]

Copyright reserved                                                             Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Automotive             5                                      DBE/2023
                                           SC/NSC

QUESTION 3: MATERIALS (GENERIC)

3.1       Why is tempering of steel done after hardening?                                         (2)

3.2       Give ONE reason for EACH of the following heat-treatment processes on
          steel:

          3.2.1      Case hardening                                                               (2)

          3.2.2      Annealing                                                                    (2)

3.3       Explain how to conduct a spark test to identify the type of steel.                      (2)

3.4       Explain how you will conduct the following tests:

          3.4.1      Filing test                                                                  (2)

          3.4.2      Bend test                                                                    (2)

3.5       What sound do the following materials make when performing a sound test?

          3.5.1      Low-carbon steel                                                             (1)

          3.5.2      High-carbon steel                                                            (1)
                                                                                                  [14]

Copyright reserved                                                             Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Automotive             6                                    DBE/2023
                                           SC/NSC

QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 E.

4.1       During which test should the crankshaft be locked to prevent the engine from
          turning?

          A     Compression test
          B     Exhaust gas analysis
          C     Cylinder leakage test
          D     Computerised diagnostic scan                                                    (1)

4.2       Which wheel alignment angles are measured using the bubble gauge?

          A     Caster, camber and toe
          B     Caster, camber and king pin inclination
          C     Toe-in, toe-out and Ackermann angle
          D     Camber, Ackermann angle and king pin inclination                                (1)

4.3       FIGURE 4.3 below shows the position of the crankpins in a four-stroke inline
          engine. Identify the number of cylinders for the crankpin positions shown.

                                           FIGURE 4.3

          A     Twin-cylinder in-line engine
          B     Three-cylinder in-line engine
          C     Eight-cylinder in-line engine
          D     Five-cylinder in-line engine                                                    (1)

4.4       An intercooler is used to …

          A     prevent the turbocharger from overheating.
          B     prevent the supercharger from overheating.
          C     cool air that is compressed by the supercharger or turbocharger.
          D     cool the different parts of an engine.                                          (1)

Copyright reserved                                                           Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Automotive                7                               DBE/2023
                                              SC/NSC

4.5       The combustion chamber volume is also known as the …

          A     swept volume.
          B     clearance volume.
          C     total volume.
          D     firing volume.                                                                (1)

4.6       The engine capacity of a four-cylinder 1 600 cm3 engine is …

          A     400 ml.
          B     1,6 ml.
          C     1 600 ml.
          D     40 ml.                                                                        (1)

4.7       Which ONE of the following determines brake power using a clamping device
          with the brake arm?

          A     Electrical dynamometer
          B     Pröny brake
          C     Chassis dynamometer
          D     Hand brake                                                                    (1)

4.8       Which ONE of the following is a cause of high carbon dioxide readings in the
          exhaust gas?

          A     Vacuum leaks
          B     Exhaust system leaks
          C     Nearly ideal air-fuel ratio
          D     Engine overheating                                                            (1)

4.9       The coolant of an engine cooling system is a mixture of …

          A     antifreeze and water.
          B     soluble oil and water.
          C     soap and water.
          D     hydraulic fluid and water.                                                    (1)

4.10      Which ONE of the following components is part of an automatic gearbox?

          A     Water pump
          B     Oil pump
          C     Gas pump
          D     Fuel pump                                                                     (1)

Copyright reserved                                                         Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Automotive               8                                  DBE/2023
                                             SC/NSC

4.11      The hydraulic pistons in an automatic gearbox control the …

          A     oil pump.
          B     valve body.
          C     gearshift lever mechanism.
          D     multi-disc clutches.                                                            (1)

4.12      Feathered tyre wear is caused by …

          A     incorrect toe setting.
          B     incorrect camber setting.
          C     wheel bounce.
          D     worn shock absorbers.                                                           (1)

4.13      Which component of the alternator controls the charging level of the battery?

          A     Stator
          B     Rectifier
          C     Regulator
          D     Slip ring                                                                       (1)

4.14      The amount of fuel injected decreases when the …

          A     engine speed increases.
          B     fuel pressure regulator does not open.
          C     the fuel filter is blocked.
          D     engine is cold.                                                                 (1)
                                                                                                [14]

Copyright reserved                                                           Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Automotive              9                                  DBE/2023
                                            SC/NSC

QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)

5.1       With reference to the engine cylinder compression test, answer the following
          questions:

          5.1.1      Give a reason for conducting the test.                                    (2)

          5.1.2      Name TWO types of compression tests.                                      (2)

          5.1.3      Give TWO reasons for low compression in a cylinder.                       (2)

5.2       FIGURE 5.2 below shows a cylinder leakage tester. Answer the questions
          that follow.

                                                          C

                                    B

                                        A                     D

                                            FIGURE 5.2

          5.2.1      Label components AD.                                                     (4)

          5.2.2      Why is pressurised air blown into the cylinder during the cylinder
                     leakage test?                                                             (2)

5.3       State THREE precautions when performing an exhaust gas analysis.                     (3)

5.4       Name THREE vehicle systems that can be scanned by the on-board
          diagnostic scanner.                                                                  (3)

5.5       State TWO faults which could be identified while performing dynamic wheel
          balancing.                                                                           (2)

5.6       Describe in THREE steps how to perform dynamic wheel balancing after a
          wheel has been checked and set up on the wheel balancer.                             (3)
                                                                                               [23]

Copyright reserved                                                          Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Automotive            10                                    DBE/2023
                                           SC/NSC

QUESTION 6: ENGINES (SPECIFIC)

6.1       FIGURE 6.1 below shows a component of a four-cylinder in-line (straight)
          engine. Answer the questions that follow.

                                           FIGURE 6.1

          6.1.1      Identify the component.                                                    (1)

          6.1.2      What is the main function of the component?                                (2)

          6.1.3      Which part of the component is drilled to balance it?                      (1)

          6.1.4      Explain static balance of this component.                                  (2)

6.2       FIGURE 6.2 below shows a vibration damper that is mounted on an internal
          combustion engine. Answer the questions that follow.

                                           FIGURE 6.2

          6.2.1      Where on an engine is a vibration damper normally mounted?                 (1)

          6.2.2      What is the function of a vibration damper?                                (1)

6.3       Name THREE different types of engine cylinder configurations.                         (3)

Copyright reserved                                                           Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Automotive           11                                    DBE/2023
                                          SC/NSC

6.4       Give TWO reasons why the power strokes of an engine are often spaced at
          equal intervals.                                                                     (2)

6.5       State THREE methods to determine the firing order of an engine.                      (3)

6.6       Answer the following questions about turbochargers:

          6.6.1      Explain the term boost.                                                   (2)

          6.6.2      Name the TWO types of turbochargers.                                      (2)

6.7       Answer the following questions about superchargers:

          6.7.1      Give TWO reasons why superchargers are fitted to engines.                 (2)

          6.7.2      Name TWO mechanical drive systems used to turn superchargers.             (2)

6.8       What does a twin-charging forced induction system consist of?                        (2)

6.9       State TWO advantages of using a twin-charging forced induction system on
          an engine.                                                                           (2)
                                                                                               [28]

Copyright reserved                                                          Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Automotive              12                                       DBE/2023
                                             SC/NSC

QUESTION 7: FORCES (SPECIFIC)

7.1       Define swept volume of an internal combustion engine.                                      (2)

7.2       State THREE methods that can be used to increase the compression ratio of
          an internal combustion engine.                                                             (3)

7.3       In an internal combustion engine the bore diameter is 90 mm and the stroke
          length is 100 mm. The compression ratio is 10,5 : 1.

          Calculate the following:

          7.3.1      The swept volume of a single cylinder in cm3                                    (3)

          7.3.2      The original clearance volume of a single cylinder in cm 3                      (3)

          7.3.3      The new bore diameter in mm if the compression ratio is increased
                     to 11 : 1. The clearance volume and stroke length remain
                     unchanged.                                                                      (7)

7.4       The following data refers to a two-cylinder two-stroke engine which was
          tested with a Pröny brake:

          Engine speed during the test:       2 000 r/min
          Mean effective pressure:            900 kPa
          Bore diameter:                      84 mm
          Stroke length:                      86 mm
          Brake arm length:                   0,4 m
          Scale reading:                      25 kg

          Calculate the following:

          7.4.1      Indicated power in kW                                                           (7)

          7.4.2      Brake power in kW                                                               (5)

          7.4.3      Mechanical efficiency                                                           (2)
                                                                                                     [32]

Copyright reserved                                                                Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Automotive              13                                     DBE/2023
                                             SC/NSC

QUESTION 8: MAINTENANCE (SPECIFIC)

8.1       TABLE 8.1 below shows the results of the gas analysis of an internal
          combustion engine. Complete TABLE 8.1 by giving ONE cause and ONE
          appropriate corrective measure for EACH given cause.

          NOTE:      Write only the answer next to             the   question      numbers
                     (8.1.1 to 8.1.4) in the ANSWER BOOK.

                  FAULTS (DEFECTS)          POSSIBLE                    CORRECTIVE
                                             CAUSES                      MEASURES
          High oxygen (O2) reading             8.1.1                       8.1.2
          High hydrocarbon (HC) reading        8.1.3                       8.1.4
                                        TABLE 8.1                                                  (4)

8.2       Explain why the following procedures are conducted on an internal
          combustion engine during a compression test:

          8.2.1       Remove the high-tension lead.                                                (1)

          8.2.2       Unplug the fuel-injection system.                                            (1)

          8.2.3       Fully open the throttle valve.                                               (1)

          8.2.4       Record the readings.                                                         (1)

8.3       State the cause of and suggest an appropriate corrective measure for the
          following cylinder leakage test results:

          8.3.1       Hissing sound at the air intake                                              (2)

          8.3.2       Hissing sound at the dipstick                                                (2)

8.4       State THREE causes of a high oil-pressure reading on an internal
          combustion engine.                                                                       (3)

8.5       A fuel pressure test is conducted on an engine.

          8.5.1       State TWO manufacturer's specifications required before the fuel
                      pressure test can be conducted.                                              (2)

          8.5.2       Where on the vehicle is the fuel-pressure tester inserted?                   (1)

          8.5.3       Why may the rubber pipe on the fuel pressure tester not be worn
                      away?                                                                        (1)

8.6       State FOUR causes of pressure drop during a cooling system pressure test.                (4)
                                                                                                   [23]

Copyright reserved                                                              Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Automotive             14                                        DBE/2023
                                            SC/NSC

QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)

9.1       A vehicle is fitted with an automatic gearbox. Explain how the following
          problems are solved:

          9.1.1      The vehicle needs to be towed over a long distance                             (1)

          9.1.2      Slippage occurs inside a torque converter                                      (1)

          9.1.3      The automatic gearbox oil overheats                                            (1)

          9.1.4      Gearshift lever position is selected before starting the vehicle               (1)

          9.1.5      Identify the correct type of oil to use in the gearbox                         (1)

9.2       FIGURE 9.2 below shows a torque converter.

                                            FIGURE 9.2

          Which components of the torque                  converter   are     described    in
          QUESTIONS 9.2.1 to 9.2.3 below?

          9.2.1      The driving member that is driven by the crankshaft                            (1)

          9.2.2      It is splined to the gearbox input shaft                                       (1)

          9.2.3      It increases the torque under load                                             (1)

9.3       Which component of the valve body is directly connected to the gear lever in
          an automatic transmission?                                                                (1)

9.4       State TWO advantages of the epicyclic gear system in the transmission of a
          motor vehicle.                                                                            (2)

Copyright reserved                                                               Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Automotive             15                                        DBE/2023
                                            SC/NSC

9.5       FIGURE 9.5 below shows the gear system of an automatic gearbox.
          Answer the questions that follow.

                         Brake band 2          Brake band 1
                                                                Annulus 1
                  Annulus 2

                                                                       Planet carrier

                  Input shaft

                                                                       Output shaft
                     Sun gear 2                                  Sun gear 1

                  Planet gear 2                                Planet gear 1

                                            FIGURE 9.5

          9.5.1        Identify the gear system in FIGURE 9.5 above.                               (1)

          9.5.2        Explain, in the CORRECT sequence, how reverse gear is obtained
                       in this gear system. Use the labels in FIGURE 9.5 to assist you in
                       your explanation.                                                           (5)

9.6       Which component circulates the oil through an automatic gearbox?                         (1)
                                                                                                   [18]

Copyright reserved                                                              Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Automotive              16                                  DBE/2023
                                             SC/NSC

QUESTION 10:         SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY
                     AND ELECTRONICS) (SPECIFIC)

10.1      State TWO features required for a well-designed steering system.                      (2)

10.2      FIGURE 10.2 below shows a wheel alignment angle. Answer the questions
          that follow.

                                                FRONT

                                    C

                                                  D

                                         B            A
                                         FIGURE 10.2

          10.2.1     Label A–C.                                                                 (3)

          10.2.2     Identify angle D.                                                          (1)

          10.2.3     What is the purpose of wheel alignment angle D?                            (2)

10.3      Wheel bounce (hop) and wheel wobble (shimmy) are symptoms of
          unbalanced wheels.

          Answer the questions below.

          10.3.1     Draw a neat labelled sketch to show wheel bounce (hop).                    (2)

          10.3.2     Draw a neat labelled sketch to show wheel wobble (shimmy).                 (2)

          10.3.3     Explain the difference between wheel wobble and wheel bounce.              (2)

10.4      Name TWO materials that are used to coat the monolith in a catalytic
          convertor.                                                                            (2)

Copyright reserved                                                           Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Automotive           17                                   DBE/2023
                                          SC/NSC

10.5      State TWO functions of EACH of the following sensors:

          10.5.1     Lambda                                                                 (2)

          10.5.2     TPS                                                                    (2)

          10.5.3     MAF                                                                    (2)

10.6      Briefly explain the operation of the common rail direct-injection system
          (CRDI).                                                                           (3)

10.7      Explain how current is generated in an alternator.                                (3)

10.8      State TWO tests performed on an alternator stator by using a multimeter.          (2)

10.9      State TWO positions where an electrical fuel pump is placed in a modern
          motor vehicle.                                                                    (2)
                                                                                            [32]

                                                                              TOTAL:        200

Copyright reserved

### Page 18

Downloaded from hlayiso.com
Mechanical Technology: Automotive               1                              DBE/2023
                                             SC/NSC

         FORMULA SHEET FOR MECHANICAL TECHNOLOGY: AUTOMOTIVE

   1.          F  ma

               Where:
                        m = Mass
                        a = Acceleration

   2.          Work done  Force  Displacement         OR        W Fs

                           Force  Displacement                        Fs
   3.          Power                                   OR        P
                                   Time                                 t

   4.          Torque  Force  Radius                  OR        T Fr

   5.          IP  P  L  A  N  n

               Where:

                       IP  Indicated power
                        P  Mean effective pressure
                        L  Stroke length
                        A  Area of piston crown
                        N  Number of power strokes per second
                        n  Number of cylinders

   6.          BP = 2 π N T

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     T  Torque

   7.          Brake power with Pröny brake = 2  π  N  F  R

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     F  Force
                     R  Brake arm length

Copyright reserved                                                       Please turn over

### Page 19

Downloaded from hlayiso.com
Mechanical Technology: Automotive                 2                DBE/2023
                                               SC/NSC

                                          BP
   8.          Mechanical efficiency =        100%
                                          IP

                                       SV  CV
   9           Compression ratio 
                                         CV

               Where:

                     SV  Swept volume
                     CV  Clearance volume

                    πD 2
   10.         SV =      L
                     4

               Where:
                     D  Bore diameter
                     L  Stroke length

                        SV
   11.         CV =
                       CR - 1

                                Product of teeth on driven gears
   12.         Gear ratio =
                                Product of teeth on driver gears

Copyright reserved

## Related documents

- [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Welding & Metalwork) Eng](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-eng/c6bfa7b8-3601-4a11-9be4-55ee65e4011f) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad) — Mechanical Technology · QP · 2023 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
