# Mechanical Technology Grade 12 NSC June 2023 QP (Eng)

> Grade 12 Mechanical Technology question paper from the NSC June Exam 2023 (English), 19 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-eng/c6bfa7b8-3601-4a11-9be4-55ee65e4011f
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2023
- Exam period: NSC June Exam
- Curriculum: CAPS
- Pages: 19

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC June 2023 QP (Eng)](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-eng/c6bfa7b8-3601-4a11-9be4-55ee65e4011f)

## About this document

Mechanical Technology · Grade 12 · NSC June Exam · 2023. Question paper, 19 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

               SENIOR CERTIFICATE EXAMINATIONS/
             NATIONAL SENIOR CERTIFICATE EXAMINATIONS

         MECHANICAL TECHNOLOGY: WELDING AND METALWORK

                                        2023

                                                                      MARKS: 200

                                                                    TIME: 3 hours

        This question paper consists of 17 pages and a 2-page formula sheet.

Copyright reserved                                                     Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork      2                                    DBE/2023
                                               SC/NSC

INSTRUCTIONS AND INFORMATION

1.         Write your centre number and examination number in the spaces provided on
           the ANSWER BOOK.

2.         Read ALL the questions carefully.

3.         Answer ALL the questions.

4.         Number the answers correctly according to the numbering system used in this
           question paper.

5.         Start EACH question on a NEW page.

6.         Show ALL calculations and units. Round off final answers to TWO decimal
           places.

7.         Candidates may use non-programmable scientific calculators and drawing
           instruments.

8.         The value of gravitational acceleration should be taken as 10 m/s 2.

9.         All dimensions are in millimetres, unless stated otherwise in the question.

10.        Write neatly and legibly.

11.        A formula sheet is attached at the end of the question paper.

12.        Use the criteria below to assist you in managing your time.

                                                                                         TIME
QUESTION                               CONTENT                        MARKS
                                                                                      IN MINUTES
                                   GENERIC
      1          Multiple-choice Questions                                  6                6
      2          Safety                                                    10               10
      3          Materials                                                 14               14
                                   SPECIFIC
      4          Multiple-choice Questions                               14                 10
      5          Terminology (Templates)                                 23                 20
      6          Tools and Equipment                                     18                 10
      7          Forces                                                  45                 40
      8          Joining Methods (Weld Inspection)                       23                 20
      9          Joining Methods (Stresses and Distortion)               18                 20
      10         Maintenance                                              8                 10
      11         Terminology (Developments)                              21                 20
                                                        TOTAL            200               180

Copyright reserved                                                                Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     3                             DBE/2023
                                               SC/NSC

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)
Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E.
1.1      Which ONE of the following safety precautions is applicable to the bench
         grinder?
         A     Oil the surface of the machine.
         B     Remove all guards when grinding.
         C     Wear safety goggles when grinding.
         D     Ensure that the machine is on.                                                (1)
1.2      What does the Occupational Health and Safety Act state regarding HIV/Aids
         awareness?
         A     All employers must make sure that the workplace is safe, and that
               employees are not at risk of contracting HIV.
         B     It does not contain common guidelines on how employers, employees
               and trade unions should respond to persons with HIV in the workplace.
         C     Employers may demote or promote an employee based on his/her
               HIV status.
         D     Employers can simply dismiss a person who has HIV.                            (1)
1.3      Which ONE of the following procedures is applicable when applying basic
         medical treatment?
         A     Examine the injured person.
         B     Remove the object from the wound.
         C     Use oily substance or lotion on a burn.
         D     Phone the insurance company.                                                  (1)
1.4      Why is steel heated slowly to a certain temperature during heat treatments?
         To ensure that …
         A     high heat is obtained.
         B     the room temperature is correct.
         C     a uniform temperature is obtained.
         D     the safety process is correct.                                                (1)
1.5      Which ONE of the following is an example of case-hardening?
         A     Frying pans
         B     Gears
         C     Wheel rims
         D     Chisels                                                                       (1)
1.6      What does the term quenching rate during heat treatment mean?
         A     Cooling rate
         B     Heating rate
         C     Tempering rate
         D     Hardening rate                                                                (1)
                                                                                             [6]

Copyright reserved                                                        Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     4                                  DBE/2023
                                               SC/NSC

QUESTION 2: SAFETY (GENERIC)

2.1      Which safety precaution must be adhered to after the work on any machine is
         completed?                                                                               (1)

2.2      Give TWO reasons why the space between the tool rest and the grinding
         wheel on a bench grinder must not exceed 3 mm.                                           (2)

2.3      Identify the workshop layouts shown in FIGURES 2.3.1 and 2.3.2 below.

         2.3.1

                                                  FIGURE 2.3.1                                    (1)

         2.3.2

                                                  FIGURE 2.3.2                                    (1)

2.4      State ONE type of personal protective equipment that must be worn when
         working on a hydraulic press machine.                                                    (1)

2.5      State ONE function of the safety guard on a portable angle grinder.                      (1)

2.6      State ONE safety precaution, other than environmental safety, that must be
         observed when using a shearing machine/guillotine.                                       (1)

2.7      State TWO safety precautions that must be adhered to when storing
         gas cylinders.                                                                           (2)
                                                                                                  [10]

Copyright reserved                                                             Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     5                                  DBE/2023
                                               SC/NSC

QUESTION 3: MATERIALS (GENERIC)

3.1       Why is tempering of steel done after hardening?                                         (2)

3.2       Give ONE reason for EACH of the following heat-treatment processes on
          steel:

          3.2.1      Case hardening                                                               (2)

          3.2.2      Annealing                                                                    (2)

3.3       Explain how to conduct a spark test to identify the type of steel.                      (2)

3.4       Explain how you will conduct the following tests:

          3.4.1      Filing test                                                                  (2)

          3.4.2      Bend test                                                                    (2)

3.5       What sound do the following materials make when performing a sound test?

          3.5.1      Low-carbon steel (LCS)                                                       (1)

          3.5.2      High-carbon steel (HCS)                                                      (1)
                                                                                                  [14]

Copyright reserved                                                             Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     6                                    DBE/2023
                                               SC/NSC

QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 E.

4.1       Which ONE of the following materials can be cut using tinsnips when
          manufacturing a template?

          A     3 mm sheet metal
          B     Hardboard
          C     Galvanised sheet metal
          D     Perspex                                                                           (1)

4.2       What is a plate girder?

          A     Hollow tubing welded together
          B     Combination of plates and angle iron welded together
          C     Retro grids welded together
          D     Combination of plates and round bars welded together                              (1)

4.3       Supplementary symbols indicate … information about welds.

          A     additional
          B     calculated
          C     difficult
          D     easy                                                                              (1)

4.4       A die is used for cutting or forming external threads on round bars and …

          A     square tubing.
          B     round tubing.
          C     plates.
          D     angle irons.                                                                      (1)

4.5       Arc welding uses a welding power supply to create an electric arc between
          an …

          A     electrode and a base metal.
          B     electrode and an electrode terminal.
          C     earth terminal and a base metal.
          D     electrode and an earthed base metal.                                              (1)

4.6       Which ONE of the following is an advantage of resistance welding?

          A     It is very good to use when welding material is 10 mm or thicker.
          B     It is used to weld Perspex.
          C     Electrical resistance is low.
          D     It is quick and easy with no filler rod.                                          (1)

Copyright reserved                                                             Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     7                                    DBE/2023
                                               SC/NSC

4.7       Which member of a framework resists a compressive force?

          A     Purlin
          B     Strut
          C     Rafter
          D     Tie                                                                                (1)

4.8       What does the abbreviation UDL stand for?

          A     Uniformly displaced load
          B     Uniformly displayed load
          C     Uniformly distorted load
          D     Uniformly distributed load                                                         (1)

4.9       When calculating strain, the original length of a bar is defined as the …

          A     ratio between stress and strain.
          B     length by which an object is shortened or lengthened.
          C     length of an object before an external load is applied.
          D     length of an object after an external load is applied.                             (1)

4.10      Which ONE of the following tests is a non-destructive test?

          A     X-ray test
          B     Bending test
          C     Machinability test
          D     Nick-break test                                                                    (1)

4.11      Which ONE of the following is a disadvantage of the liquid dye penetration
          test?

          A     Detects only subsurface defects
          B     Not easy to conduct
          C     Cannot work on porous materials
          D     Suitable for ferrous materials                                                     (1)

4.12      Pearlite structure is a mixture of … in layers.

          A     iron and iron carbide
          B     iron and brass
          C     cast iron and cast steel
          D     aluminium and copper                                                               (1)

Copyright reserved                                                              Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork      8                              DBE/2023
                                                SC/NSC

4.13      What is the disadvantage of using jigs, fixtures and clamps when welding?

          A     Decreases internal stress
          B     Increases external stress
          C     Decreases external stress
          D     Increases internal stress                                                      (1)

4.14      Identify the type of hopper in FIGURE 4.14 below.

                                               FIGURE 4.14

          A     Square to square on centre
          B     Square to round
          C     Rectangle to square off centre
          D     Cone frustum                                                                   (1)
                                                                                               [14]

Copyright reserved                                                          Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     9                           DBE/2023
                                               SC/NSC

QUESTION 5: TERMINOLOGY (TEMPLATES) (SPECIFIC)

5.1       State the purpose of purlins in roof trusses.                                    (2)

5.2       Identify the weld symbols in FIGURES 5.2.1 to 5.2.4 below.

          5.2.1

                                                  FIGURE 5.2.1                             (1)

          5.2.2

                                                  FIGURE 5.2.2                             (1)

          5.2.3

                                                  FIGURE 5.2.3                             (1)

          5.2.4

                                                  FIGURE 5.2.4                             (1)

5.3       State ONE use of a strip template.                                               (1)

5.4       A mild steel ring with an inside diameter of 180 mm must be manufactured
          from a Ø12 mm round bar.

          Calculate the following:

          5.4.1      The mean diameter of the ring                                         (2)

          5.4.2      The mean circumference of the ring (round off answer to the
                     nearest whole number)                                                 (3)

Copyright reserved                                                      Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork         10                           DBE/2023
                                                   SC/NSC

5.5       FIGURE 5.5 below shows a weld symbol. Fully describe the weld symbol and
          give the meaning of EACH of the dimensions in the diagram.

                                               FIGURE 5.5                                       (4)

5.6       FIGURE 5.6 below shows a roof truss. Label parts A–E.

                                                            B

                                                                C
                            A
                                                                         D
                                               E

                                               FIGURE 5.6                                       (5)

5.7       What is the advantage of using lattice beams over a longer span?                      (2)
                                                                                                [23]

Copyright reserved                                                           Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     11                                     DBE/2023
                                               SC/NSC

QUESTION 6: TOOLS AND EQUIPMENT (SPECIFIC)

6.1       State THREE main uses of a bench grinder.                                                  (3)

6.2       What does MIG stand for?                                                                   (1)

6.3       Describe the operating principle of a plasma cutter.                                       (4)

6.4       Name the THREE types of taps used to cut internal screw thread.                            (3)

6.5       Name the hand tool that is used to remove slag from an arc-welded joint.                   (1)

6.6       What is the function of the vertical rollers on a vertical rolling machine?                (1)

6.7       Give TWO reasons why coolant is used on a horizontal band saw.                             (2)

6.8       Name THREE processes where oxy-acetylene equipment is used.                                (3)
                                                                                                     [18]

Copyright reserved                                                                Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     12                                    DBE/2023
                                               SC/NSC

QUESTION 7: FORCES (SPECIFIC)

7.1       FIGURE 7.1 below shows a framework with members AE, BF, CF, DE and
          EF. Graphically determine the magnitude and type/nature of each member.

          Scale:     Space diagram: 1 : 100
                     Force diagram: 1 mm = 5 N

                                         300 N                            100 N

                                                            B
                                               45°
                                                            F
                                  A
                                                                     C
                                           E

                             45°                      45°
                                          D
                                       7 000 mm
                     100 N                                  300 N

                                               FIGURE 7.1                                            (15)

7.2      FIGURE 7.2 below shows a uniform supported beam that is subjected to
         three point loads.

                          8 kN                       4 kN                6 kN

                A             B                         C                  D           E

                     2m                  3m                     3m              2m
           RL                                                                              RR

                                               FIGURE 7.2

          Calculate the following:

          7.2.1      The magnitude of the reaction at support RL                                     (4)

          7.2.2      The magnitude of the reaction at support RR                                     (4)

          7.2.3      The bending moments at points B, C and D                                        (6)

          7.2.4      Draw a bending-moment diagram of the beam.

                     Scale:        Beam: 1 : 100 (distances)
                                   Bending moments: 2 mm = 1 kNm                                     (4)

Copyright reserved                                                                Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     13                                DBE/2023
                                               SC/NSC

7.3       A compressive load of 80 kN is exerted onto a round bar with a diameter of
          30 mm. The original length of the round bar is 3 m.

          Calculate the following:

          7.3.1      The cross-sectional area of the bar in m2                                   (2)

          7.3.2      The stress caused in the material in MPa                                    (3)

          7.3.3      The strain caused if the change in length of the bar is 0,06 mm             (2)

          7.3.4      Young's modulus of elasticity in GPa                                        (3)

7.4       A round steel bar with a cross-sectional area of 0,9 x10-5 m2 is subjected to a
          maximum tensile load of 55 kN.

          Calculate the maximum stress.                                                          (2)
                                                                                                 [45]

Copyright reserved                                                            Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     14                             DBE/2023
                                               SC/NSC

QUESTION 8: JOINING METHODS (WELD INSPECTION) (SPECIFIC)

8.1       State TWO aspects to check when doing a visual inspection on welded joints.         (2)

8.2       State ONE property that is tested when conducting a free-bend test on a
          welded joint.                                                                       (1)

8.3       Define weld defect.                                                                 (2)

8.4       State TWO causes of the following weld defects:

          8.4.1      Undercutting                                                             (2)

          8.4.2      Blow hole                                                                (2)

8.5       Name TWO examples of destructive tests done on welded joints.                       (2)

8.6       Explain how to conduct an X-ray test on a welded joint.                             (6)

8.7       Name the TWO types of dyes that can be used for a liquid dye penetration
          test.                                                                               (2)

8.8       State TWO examples of internal weld defects.                                        (2)

8.9       State TWO methods of reducing centre-line cracks.                                   (2)
                                                                                              [23]

Copyright reserved                                                         Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     15                                   DBE/2023
                                               SC/NSC

QUESTION 9: JOINING METHODS (STRESSES AND DISTORTION) (SPECIFIC)

9.1       State TWO factors that affect distortion and residual stress in a welded joint.          (2)

9.2       Describe shrinkage in a welded joint.                                                    (2)

9.3       State TWO factors that affect the grain size of cold-worked steel.                       (2)

9.4       Describe the difference between cold working and hot working of steel.                   (4)

9.5       State FOUR methods used to reduce distortion.                                            (4)

9.6       Identify the types of distortion in FIGURES 9.6.1 and 9.6.2 below.

          9.6.1

                                                  FIGURE 9.6.1                                     (1)

          9.6.2

                                                  FIGURE 9.6.2                                     (1)

9.7       Explain the result when metal is cooled rapidly. Refer to the internal and
          external areas of the metal.                                                             (2)
                                                                                                   [18]

QUESTION 10: MAINTENANCE (SPECIFIC)

10.1      Define maintenance.                                                                      (3)

10.2      State TWO general maintenance guidelines for a drill press.                              (2)

10.3      What is the function of tagging plates?                                                  (1)

10.4      Give TWO reasons why it is important to keep service records of machines.                (2)
                                                                                                   [8]

Copyright reserved                                                              Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     16                             DBE/2023
                                               SC/NSC

QUESTION 11: TERMINOLOGY (DEVELOPMENTS) (SPECIFIC)

11.1      FIGURE 11.1 below shows the top view of a hopper with a vertical height
          (VH) of 450 mm. Answer the questions that follow.

                      D                                                     C

                                                     300

                                    4                                3

                500         250

                                    1                                2
                                                                     0

                      A                                                      B
                                                    500

                                               FIGURE 11.1

          11.1.1      Identify the hopper in FIGURE 11.1.                                   (3)

          11.1.2      Calculate the true lengths of the following:

                      (a)   A–1                                                             (2)

                      (b)   A–2                                                             (2)

                      (c)   B–3                                                             (2)

Copyright reserved                                                       Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork     17                                          DBE/2023
                                               SC/NSC

11.2      FIGURE 11.2 below shows the top view of a cone frustum. The vertical height
          is 500 mm. The large diameter is 800 mm and the small diameter is 600 mm.
          Answer the questions that follow.

                                                                   C

                                                         2                       B
                                                               1
                                                                                     150
                                                         30°
                                                                   0         A

                                                        260            140

                                               FIGURE 11.2

          Calculate the true lengths of the following:

          11.2.1     A–B                                                                                (3)

          11.2.2     0–1                                                                                (3)

          11.2.3     A–0                                                                                (4)

11.3      Where is a square-to-round transformer usually used?                                          (2)
                                                                                                        [21]

                                                                                           TOTAL:       200

Copyright reserved

### Page 18

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork           1                        DBE/2023
                                                    SC/NSC

                     FORMULA SHEET FOR MECHANICAL TECHNOLOGY
                                     WELDING AND METALWORK

1.     STRESS AND STRAIN

                  π d2
 1.1     Ashaft 
                    4

                   π D 2  d 2 
 1.2     Apipe 
                         4
                             Maximum stress/Break stress
 1.3     Safety factor =
                                 Safe working stress

                     Force                                   F
 1.4     Stress                          OR            σ
                     Area                                    A

                     Change in length                                 Δl
 1.5     Strain                                    OR           ε
                      Original length                                 ol

                                 Stress                               σ
 1.6     Young' s modulus                         OR            E
                                 Strain                               ε

2.     PYTHAGORAS' THEOREM AND TRIGONOMETRY

                                 r
          y

                                               𝜽
                             x

               y
 2.1    sin θ 
               r
               x
 2.2    cosθ 
               r
               y
 2.3    tanθ 
               x
 2.4    r 2  x2  y2      OR        a2  b2  c2

Copyright reserved                                                         Please turn over

### Page 19

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork      2     DBE/2023
                                               SC/NSC

3.     TEMPLATES AND DEVELOPMENTS

3.1      Mean Ø = Outside Ø – Plate thickness
                        OR
         Mean Ø = Inside Ø + Plate thickness

3.2      Mean circumference = π × Mean Ø

            (where Ø = diameter)

Copyright reserved

## Related documents

- [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad) — Mechanical Technology · QP · 2023 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
