# Mechanical Technology Grade 12 NSC November 2016 QP (Eng) > Grade 12 Mechanical Technology question paper from the NSC November Exam 2016 (English), 20 pages. Read online or download the free PDF. - Page: https://www.hlayiso.com/library/mechanical-technology-nov-2016-eng/3a98f967-9b07-47ab-b556-3e9fceb211b1 - Updated: 2026-09-27 - Subject: Mechanical Technology - Grade: Grade 12 - Document type: Question paper - Year: 2016 - Exam period: NSC November Exam - Curriculum: CAPS - Pages: 20 Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC November 2016 QP (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2016-eng/3a98f967-9b07-47ab-b556-3e9fceb211b1) ## About this document Mechanical Technology · Grade 12 · NSC November Exam · 2016. Question paper, 20 pages. Read online or download the PDF. Read it free online on the page above; download the PDF from there. ## Document text Text extracted from the PDF. Layout, diagrams and tables may not survive extraction. ### Page 1 Downloaded from hlayiso.com GRAAD 12 NATIONAL SENIOR CERTIFICATE GRADE 12 MECHANICAL TECHNOLOGY NOVEMBER 2016 MARKS: 200 TIME: 3 hours This question paper consists of 16 pages and a 4-page formula sheet. Copyright reserved Please turn over ### Page 2 Downloaded from hlayiso.com Mechanical Technology 2 DBE/November 2016 NSC INSTRUCTIONS AND INFORMATION 1. This question paper consists of TEN questions. 2. Write your centre number and examination number in the spaces provided on the ANSWER BOOK. 3. Read ALL the questions carefully. 4. Answer ALL the questions. 5. Number the answers correctly according to the numbering system used in this question paper. 6. Start EACH question on a NEW page. 7. Show ALL calculations and units. Round off ALL answers to TWO decimal places. 8. Candidates may use non-programmable, scientific calculators and drawing instruments. 9. Take the value of gravitational force as 10 m/s-2. 10. All dimensions are in millimetres, unless stated otherwise in the question. 11. A formula sheet for your use is attached to this question paper. 12. Write neatly and legibly. 13. Use the guidelines below to assist you in managing your time. TIME QUESTION CONTENT MARKS (minutes) 1 Multiple-choice questions 20 15 2 Safety 10 10 3 Tools and Equipment 12 10 4 Materials 13 10 5 Terminology 30 20 6 Joining Methods 25 25 7 Forces 30 30 8 Maintenance 15 15 9 Systems and Control 25 25 10 Turbines 20 20 TOTAL 200 180 Copyright reserved Please turn over ### Page 3 Downloaded from hlayiso.com Mechanical Technology 3 DBE/November 2016 NSC QUESTION 1: MULTIPLE-CHOICE QUESTIONS Various options are provided as possible answers to the following questions. Write down the question number (1.1–1.20), choose the answer and make a cross (X) over the letter (A–D) of your choice in the ANSWER BOOK. EXAMPLE: 1.21 A B C D 1.1 What safety measure must be adhered to with regard to the milling machine, according to the Occupational Health and Safety Act, 1993 (Act 85 of 1993)? A Do not use a wrench on revolving work. B Remove guards while cutting material. C Make sure that the wheel is dressed. D Use the machine table as an anvil. (1) 1.2 What safety measure is applicable to the hydraulic press in terms of the Occupational Health and Safety Act? A Do not exceed the safe pressure limit. B Work at a safe speed. C Lubricate the work piece before mounting it on the press. D Use the maximum pressure for thicker materials. (1) 1.3 A Brinell tester is used to test the … of a material. A tension B elasticity C hardness D brittleness (1) 1.4 Which ONE of the following statements describes the function of the tensile tester? A Determines the length of the material B Changes the length of the material C Determines the tensile strength of the material D Determines the tensile ratio of the material (1) 1.5 A ferrite structure is … A strong and brittle. B soft and ductile. C hard and brittle. D soft and brittle. (1) Copyright reserved Please turn over ### Page 4 Downloaded from hlayiso.com Mechanical Technology 4 DBE/November 2016 NSC 1.6 The lower critical temperature for carbon steel is … A 100 °C. B 950 °C. C 720 °C. D 610 °C. (1) 1.7 Which milling procedure is shown in FIGURE 1.1? FIGURE 1.1 A Up-cut milling B Gear cutting C Down-cut milling D Centring of a milling cutter (1) 1.8 What is the included angle of a metric V-screw thread? A 30° B 29° C 60° D 55° (1) 1.9 Which ONE of the following is a common cause of porosity in a welding joint? A Dirty or wet electrodes used when arc welding B Slag not cleaned off the first weld surface before a second weld run C Faulty restart by not restarting at the top of the previous weld run D A welding current that is too low (1) 1.10 What is the definition of slag inclusion as a welding defect? A Metallic solids entrapped in the weld metal B Gas pores occurring in the solidified weld bead C Non-metallic solids entrapped in the weld metal D Melted surface impurities trapped in the weld surface (1) Copyright reserved Please turn over ### Page 5 Downloaded from hlayiso.com Mechanical Technology 5 DBE/November 2016 NSC 1.11 What does straight line OA represent in the stress-strain graph shown in FIGURE 1.2? D BC A E Stress O Strain FIGURE 1.2 A The difference between the stress and strain B The indirect proportionality between the stress and strain C The proportionality between the stress and strain D The similarity between the stress and strain (1) 1.12 What is the class of the lever shown in FIGURE 1.3? LOAD EFFORT FULCRUM FIGURE 1.3 A 1st class B 2nd class C 3rd class D 4th class (1) Copyright reserved Please turn over ### Page 6 Downloaded from hlayiso.com Mechanical Technology 6 DBE/November 2016 NSC 1.13 The law of moments is defined as a system of forces that is in equilibrium if the ... A coefficient of the clockwise moments around a point is equal to the coefficient of the anticlockwise moments around the same point. B difference of the clockwise moments around a point is equal to the difference of the anticlockwise moments around the same point. C sum of the clockwise moments around a point is equal to the sum of the anticlockwise moments around the same point. D product of the clockwise moments around a point is equal to the product of the anticlockwise moments around the same point. (1) 1.14 Which ONE of the following is an advantage of a chain-drive system? A Low cost B No lubrication needed C Smooth operation D Slip-free drive (1) 1.15 Which step in adjusting the tension in a chain of a chain drive is shown at point A in FIGURE 1.4? A FIGURE 1.4 A Check the distance between the centres. B Slacken the clamp bolts and screw the adjusting bolt in or out. C Check the amount of slack in the chain. D Tighten the clamping bolts. (1) Copyright reserved Please turn over ### Page 7 Downloaded from hlayiso.com Mechanical Technology 7 DBE/November 2016 NSC 1.16 FIGURE 1.5 shows a gear train with three gears that mesh. What is gear B called? GEAR A GEAR C (DRIVER) (DRIVEN) GEAR B FIGURE 1.5 A Helical gear B Rack C Idler gear D Pinion (1) 1.17 What will the rotation frequency of pulley A be if pulley B is rotating at 1 000 r/min, as shown in FIGURE 1.6? Pulley B (Driver) Ø 25 mm Pulley A (Driven) Ø 50 mm FIGURE 1.6 A 1 000 r/min B 2 000 r/min C 500 r/min D 100 r/min (1) Copyright reserved Please turn over ### Page 8 Downloaded from hlayiso.com Mechanical Technology 8 DBE/November 2016 NSC 1.18 Determine the speed ratio of the chain drive of the racing bicycle shown in FIGURE 1.7. 16 teeth 40 teeth FIGURE 1.7 A 40 : 1 B 1 : 40 C 2,5 : 1 D 1 : 2,5 (1) 1.19 What is the function of the waste gate in a turbo charger? It releases excess … A pressure. B moisture. C heat. D oil. (1) 1.20 A steam turbine is used to … A increase the fuel consumption in relation to engine output. B increase the volumetric efficiency of a four-stroke diesel engine. C drive a generator to generate electricity. D decrease the atmospheric pressure of an engine. (1) [20] Copyright reserved Please turn over ### Page 9 Downloaded from hlayiso.com Mechanical Technology 9 DBE/November 2016 NSC QUESTION 2: SAFETY 2.1 All personal and environmental safety rules were followed when an operator used a surface grinder. State TWO safety rules that should be followed while the surface grinder is in operation. (2) 2.2 Give TWO examples of personal protective equipment that should be used while arc welding. (2) 2.3 State TWO safety rules to be taken into account before applying force to a bearing puller. (2) 2.4 What is the maximum safe distance between the grinding wheel and the tool rest on a bench grinder? (1) 2.5 State THREE safety precautions to be adhered to when a Rockwell hardness tester is used. (3) [10] QUESTION 3: TOOLS AND EQUIPMENT 3.1 Give TWO reasons for conducting a bending test on a roof beam. (2) 3.2 Give TWO reasons for a high CO reading when conducting a gas analysis test on the engine of a motor vehicle. (2) 3.3 State TWO advantages of the MIG/MAGS welding process. (2) 3.4 Name TWO tests that can be done with a multimeter. (2) 3.5 Due to engine power loss in a vehicle the mechanic conducts a compression test according to certain procedures. Why are the procedures below followed? 3.5.1 Remove the high-tension lead. (1) 3.5.2 Unplug the fuel-injection system. (1) 3.5.3 Open the throttle valve fully. (1) 3.5.4 Record the readings. (1) [12] Copyright reserved Please turn over ### Page 10 Downloaded from hlayiso.com Mechanical Technology 10 DBE/November 2016 NSC QUESTION 4: MATERIALS 4.1 State TWO properties of the cementite structure of carbon steel. (2) 4.2 What is the purpose of case hardening on a camshaft? (2) 4.3 What is the purpose of tempering hardened steel? (2) 4.4 Show, by means of a neat drawing, the following elements on an iron-carbon equilibrium diagram: 4.4.1 Carbon content from 0% to 1,4% (1) 4.4.2 Temperature of 0 °C to 1 000 °C (1) 4.4.3 AC 1 -line (1) 4.4.4 AC 3 -line (1) 4.4.5 Austenite structure (1) 4.4.6 Ferrite structure (1) 4.4.7 Pearlite structure (1) [13] QUESTION 5: TERMINOLOGY 5.1 FIGURE 5.1 shows two spur gears that mesh. Gear A Gear B 90 teeth 30 teeth PCD = 90 mm Y FIGURE 5.1 Use the information above and calculate the: 5.1.1 Module of the small gear (2) 5.1.2 Outside diameter of the big gear (2) 5.1.3 PCD of the big gear (2) 5.1.4 Dedendum of the big gear (2) 5.1.5 Centre distance between the two gears (distance Y) (3) 5.1.6 Required indexing for a gear with 33 teeth (3) Copyright reserved Please turn over ### Page 11 Downloaded from hlayiso.com Mechanical Technology 11 DBE/November 2016 NSC 5.2 A taper key must be made to fit onto a 92 mm diameter shaft. Calculate the following: 5.2.1 The width of the key (2) 5.2.2 The length of the key (2) 5.2.3 The thickness of the key at the bigger end (2) 5.2.4 The thickness of the key at the smaller end (4) 5.3 Explain the functions of the following components on the dividing head used on a milling machine: 5.3.1 Index plate (2) 5.3.2 Sector arms (2) 5.4 State TWO methods that may be used on a centre lathe to cut external V-screw threads with a single-point screw-cutting tool. (2) [30] QUESTION 6: JOINING METHODS 6.1 State TWO causes of EACH of the following welding defects: 6.1.1 Undercutting (2) 6.1.2 Lack of fusion (2) 6.2 Explain how the ultrasonic test is conducted on a welding joint. (6) 6.3 State ONE advantage of conducting an ultrasonic test rather than an X-ray test on a welding joint. (1) 6.4 An X-ray test is conducted on a welded joint. How are the results observed and recorded? (2) 6.5 Explain the purpose of the dye penetration test on a welding joint. (2) 6.6 Give TWO examples of destructive tests that are conducted on welded joints. (2) 6.7 Name TWO gases used with MIG/MAGS welding. (2) Copyright reserved Please turn over ### Page 12 Downloaded from hlayiso.com Mechanical Technology 12 DBE/November 2016 NSC 6.8 FIGURE 6.1 shows the MIG/MAGS welding process. Label A–F. D C E B F A FIGURE 6.1 (6) [25] QUESTION 7: FORCES 7.1 Four pulling forces of 100 N, 200 N, 300 N and 185 N are acting from the same acting point, as shown in FIGURE 7.1. Determine, by means of calculations, the magnitude and direction of the resultant of the system of forces in FIGURE 7.1. 200 N 300 N 110° 45° 185 N 100 N FIGURE 7.1 (13) 7.2 A load of 40 kN causes a tensile stress of 20 MPa in a round brass bar. The original length of the bar is 300 mm. Young's modulus for brass is 90 GPa. Calculate the: 7.2.1 Diameter of the bar (5) 7.2.2 Strain (3) 7.2.3 Change in length (3) Copyright reserved Please turn over ### Page 13 Downloaded from hlayiso.com Mechanical Technology 13 DBE/November 2016 NSC 7.3 FIGURE 7.2 shows a uniform beam that is supported by two vertical supports, A and B. A uniformly distributed force of 80 N/m is exerted over the whole length of the beam. Determine, by means of calculations, the magnitudes of the reactions in supports A and B. 550 N 300 N 80 N/m 2m 5m 3m 2m A B FIGURE 7.2 (6) [30] QUESTION 8: MAINTENANCE 8.1 Name THREE effects of a lack of routine maintenance. (3) 8.2 Name TWO subgroups of preventative maintenance. (2) 8.3 Define the following properties of oils: 8.3.1 Pour point (2) 8.3.2 Flashpoint (2) 8.4 Why are belts on belt drives adjusted or replaced regularly? (2) 8.5 Why is cutting fluid used on the cutting tool during the machining processes on a centre lathe? (2) 8.6 How are chain drives maintained? (2) [15] Copyright reserved Please turn over ### Page 14 Downloaded from hlayiso.com Mechanical Technology 14 DBE/November 2016 NSC QUESTION 9: SYSTEMS AND CONTROL 9.1 FIGURE 9.1 shows a belt-drive system with a 230 mm driver pulley. The belt speed in this system is 36 m.s-1. The tensile force in the slack side is 140 N and the ratio between the force in the tight side and the force in the slack side is 2,5. NDR = ? r/min DDR = 230 mm T2 T1 FIGURE 9.1 Calculate the: 9.1.1 Rotation frequency of the driver pulley in r/min (4) 9.1.2 Power transmitted in this system (4) 9.2 FIGURE 9.2 shows a gear-drive system. Driver gear A on the shaft of the electric motor has 18 teeth that mesh with gear B with 36 teeth on a counter shaft. On the counter shaft is a second driver gear, C, with 16 teeth that mesh with gear D with 46 teeth on a second counter shaft. The second counter shaft has a third driver gear, E, with 40 teeth, which drives gear F with 60 teeth on the output shaft. Electrical D E motor A 18 46 40 Counter shaft B 36 C 16 F Counter 60 shaft Output shaft FIGURE 9.2 Calculate the: 9.2.1 Rotation frequency of the input shaft on the electric motor if the output shaft needs to rotate at 160 r/min (3) 9.2.2 Velocity ratio between the input shaft and output shaft (2) Copyright reserved Please turn over ### Page 15 Downloaded from hlayiso.com Mechanical Technology 15 DBE/November 2016 NSC 9.3 A hydraulic system is used to lift a lathe. The specifications of the system are presented diagrammatically in FIGURE 9.3. Ø 40 mm Ø 75 mm 275 N Load = ? kg Piston A Piston B FIGURE 9.3 Calculate the: 9.3.1 Fluid pressure in the hydraulic system when in equilibrium (4) 9.3.2 Load in kilogram that can be lifted by piston B if a force of 275 N is exerted upon piston A (4) 9.4 What is the purpose of traction control in a vehicle? (2) 9.5 Airbags in a vehicle are described as a passive safety feature. Explain the meaning of the term passive safety feature. (2) [25] QUESTION 10: TURBINES 10.1 Name TWO types of blowers that are used as superchargers in the engine of a motor vehicle. (2) 10.2 State the main function of superchargers. (2) 10.3 State TWO advantages of a supercharger when compared to a turbocharger. (2) 10.4 How is a turbocharger driven? (1) 10.5 Define the run-away speed of a water turbine. (2) Copyright reserved Please turn over ### Page 16 Downloaded from hlayiso.com Mechanical Technology 16 DBE/November 2016 NSC 10.6 State the operational principles of EACH of the three water turbines shown in FIGURES 10.1, 10.2 and 10.3. 10.6.1 FIGURE 10.1 (2) 10.6.2 FIGURE 10.2 (2) 10.6.3 FIGURE 10.3 (2) 10.7 A gas turbine that is used as a jet engine is shown in FIGURE 10.4. Label phases A to D and part E. A B C D E FIGURE 10.4 (5) [20] TOTAL: 200 Copyright reserved ### Page 17 Downloaded from hlayiso.com Mechanical Technology 1 DBE/November 2016 NSC FORMULA SHEET 1. BELT DRIVES 1.1 N dr × D dr = N dn × D dn πDN 1.2 Belt speed = where N is in r/min 60 π ( D + t )× N 1.3 Belt speed = (t = belt thickness) 60 1.4 Belt mass = area × length × density (A = thickness × width) diameter of driven pulley 1.5 Speed ratio = diameter of driver pulley 1.6 Belt length (flat belt) = [(D + d) × 1,57] + 2 × centre distance π( D + d ) 2 ( D − d ) 2 1.7 Open-belt length = + + 2c 2 4c π( D + d ) 2 ( D + d ) 2 1.8 Crossed -belt length = + + 2c 2 4c T1 1.9 Ratio of tight side to slack side = T2 (T1 − T2 ) π D N 1.10 Power (P) = where N is in r/min 60 T1 = force in the tight side T2 = force in the slack side T1 − T2 = effective force (Te ) 1.11 Power (P) = (T1 − T2 ) × V where V = belt speed in m/s 2πNT 1.12 Power ( P ) = where N is in r/min 60 T1 1.13 Width = permissible tensile force Copyright reserved Please turn over ### Page 18 Downloaded from hlayiso.com Mechanical Technology 2 DBE/November 2016 NSC 2. STRESS AND STRAIN force F 2.1 Stress = or ( σ = ) area A change in length ( ΔL ) 2.2 Strain ( ε ) = original length ( L ) stress σ 2.3 Young' s mod ulus ( E ) = or ( ) strain ε πd 2 2.4 Area of a round bar = A = 4 2.5 Area of a pipe = A = ( π D2 − d 2 ) 4 2.6 Area of a square bar = A = L2 or A = L × B 3. HYDRAULICS force ( F ) 3.1 Pressure ( P ) = area ( A ) 3.2 Volume = (cross-sectional area) × stroke length 3.3 Work done = force × distance 4. KEYS AND KEYWAYS diameter of shaft 4.1 Width of key = 4 diameter of shaft 4.2 Thickness of key = 6 4.3 Length of key = 1,5 × diameter of shaft 4.4 Standard taper for taper key = 1 in 100 or 1 : 100 Copyright reserved Please turn over ### Page 19 Downloaded from hlayiso.com Mechanical Technology 3 DBE/November 2016 NSC 5. LEVERS load (W) 5.1 Mechanical advantage (MA) = effort (F) input movement 5.2 Velocity ratio = output movement 5.3 Input movement (IM) = effort × distance moved by effort 5.4 Output movement (OM) = load × distance moved by load 6. GEAR DRIVES 6.1 N dr × D dr = N dn × D dn 2πNT 6.2 Power (P) = 60 product of the number of teeth on the driven gears 6.3 Gear ratio = product of the number of teeth on the driver gears N input product of the number of teeth on the driven gears 6.4 = N output product of the number of teeth on the driver gears 6.5 Torque = force × radius 6.6 Torque transmitted = gear ratio × input torque pitch-circle diameter (PCD) 6.7 Module (m) = number of teeth (T) 6.8 N 1T1 = N 2 T2 circular pitch (CP) × number of teeth (T) 6.9 Pitch-circle diameter (PCD) = π 6.10 Pitch-circle diameter (PCD) = m × T 6.11 Outside diameter (OD) = m(T + 2) 6.12 Outside diameter (OD) = pitch-circle diameter (PCD) + 2 module Copyright reserved Please turn over ### Page 20 Downloaded from hlayiso.com Mechanical Technology 4 DBE/November 2016 NSC 6.13 Addendum = module (m) 6.14 Dedendum = 1,157 m or Dedendum = 1,25 m 6.15 Cutting depth = 2,157 m or Cutting depth = 2,25 m 6.16 Clearance = 0,157 m or Clearance = 0,25 m 6.17 Circular pitch (CP) = m × π (PCD) A (PCD) B 6.18 Centre distance between gear A and B = + 2 2 7. SCREW THREADS 7.1 Pitch diameter = outside diameter – ½pitch 7.2 Pitch circumference = π × pitch diameter 7.3 Lead = pitch × number of starts 7.4 Height of screw thread = 0,866 × pitch 7.5 Depth of screw thread = 0,613 × pitch 8. INDEXING 8.1 Cincinnati dividing head table for milling machine Cincinnati Index Plate Side 1 24 25 28 30 34 37 38 39 41 42 43 Side 2 46 47 49 51 53 54 57 58 59 62 66 40 8.2 Indexing = (where n = number of divisions) n Copyright reserved ## Related documents - [Mechanical Technology Nov 2016 Memo Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2016-memo-eng/5e2bea9e-f108-440c-a98e-4984091bb5af) — Mechanical Technology · Memo · 2016 · Eng - [Gr12 MCHT S16 QP Afr](https://www.hlayiso.com/library/gr12-mcht-s16-qp-afr/9c20cbdb-35c9-416e-9d01-387a3ba92333) — Mechanical Technology · QP · 2016 · Afr - [MT Feb March 2016 Afr](https://www.hlayiso.com/library/mt-feb-march-2016-afr/c6045d95-1e69-45d4-b04b-8316e67a8172) — Mechanical Technology · QP · 2016 · Afr - [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr - [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr - [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng ## More from Grade 12 Mechanical Technology - [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP - [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr - [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr - [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng - [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng - [Mechanical Technology May-June 2024 (Fitting and Machining) MG Afr](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-memorandum-afrikaans/03c703c8-8125-4d5a-a124-37013b381c7a) — Memo · 2024 · Afr ## Collection - [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers) --- Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.