# Mechanical Technology Grade 12 NSC November 2023 QP (Eng)

> Grade 12 Mechanical Technology question paper from the NSC November Exam 2023 (English), 21 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2023
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 21

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC November 2023 QP (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad)

## About this document

Mechanical Technology · Grade 12 · NSC November Exam · 2023. Question paper, 21 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

                     MECHANICAL TECHNOLOGY: AUTOMOTIVE

                                NOVEMBER 2023

MARKS: 200

TIME: 3 hours

        This question paper consists of 19 pages and a 2-page formula sheet.

Copyright reserved                                               Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Automotive               2                          DBE/November 2023
                                               NSC

INSTRUCTIONS AND INFORMATION

1.         Write your centre number and examination number in the spaces provided on
           the ANSWER BOOK.

2.         Read ALL the questions carefully.

3.         Answer ALL the questions.

4.         Number the answers correctly according to the numbering system used in this
           question paper.

5.         Start EACH question on a NEW page.

6.         Show ALL calculations and units. Round off final answers to TWO decimal
           places.

7.         Candidates may use non-programmable scientific calculators and drawing
           instruments.

8.         The value of gravitational acceleration should be taken as 9,81 m/s2 or
           10 m/s2.

9.         ALL dimensions are in millimetres, unless stated otherwise in the question.

10.        Write neatly and legibly.

11.        A formula sheet is attached at the end of the question paper.

12.        Use the criteria below to assist you in managing your time.

                                                                               TIME IN
QUESTION                            CONTENT                      MARKS
                                                                               MINUTES
                                 GENERIC
      1         Multiple-choice Questions                            6              6
      2         Safety                                              10             10
      3         Materials                                           14             14
                                 SPECIFIC
      4         Multiple-choice Questions                           14             10
      5         Tools and Equipment                                 23             20
      6         Engines                                             28             25
      7         Forces                                              32             25
      8         Maintenance                                         23             20
      9         Systems and Control (Automatic Gearbox)             18             20
                Systems and Control (Axles, Steering
      10                                                            32             30
                Geometry and Electronic)
                                                     TOTAL         200             180

Copyright reserved                                                             Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Automotive             3                             DBE/November 2023
                                             NSC

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E.

1.1       Who is responsible for safe working conditions in the workplace?

          A   Workersʹ union
          B   Employer
          C   Employee
          D   Department of Labour                                                                 (1)

1.2       Identify the Act that seeks to protect the worker from physical injuries in the
          workplace:

          A   Occupational Health and Safety Act (OHSA), 1993 (Act 85 of 1993)
          B   Labour Relations Act (LRA), 1995 (Act 66 of 1995)
          C   Employment Equity Act (EEA), 1998 (Act 55 of 1998)
          D   Basic Conditions of Employment Act (BCEA), 1997 (Act 75 of 1997)                     (1)

1.3       Which safety precaution must be applied when arc welding?

          A     Wet the work piece before welding to prevent overheating.
          B     Do not let oil and grease come into contact with the oxygen fittings.
          C     Use completely insulated electrode holders.
          D     Ensure that you always open the acetylene valve slowly.                            (1)

1.4       Identify the test shown in FIGURE 1.4 below.

                                            FIGURE 1.4

          A     Sound test
          B     Ultrasonic test
          C     Spark test
          D     Cutting test                                                                       (1)

Copyright reserved                                                              Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Automotive           4                         DBE/November 2023
                                           NSC

1.5       Which heat-treatment process relieves the internal stresses produced by
          machining, forging and welding?

          A     Normalising
          B     Case hardening
          C     Tempering
          D     Hardening                                                                   (1)

1.6       FIGURE 1.6 below shows the changes in metal structures during the
          annealing process. What change is indicated at Y?

                                                    Y

                                          FIGURE 1.6

          A     Recovery
          B     Grain growth
          C     Recrystallisation
          D     Grain crystallisation                                                       (1)
                                                                                            [6]

QUESTION 2: SAFETY (GENERIC)

2.1       State TWO checks that must be done on injured persons before removing
          them from a danger zone.                                                          (2)

2.2       Name TWO safety devices fitted to power guillotines.                              (2)

2.3       State TWO safety precautions that must be conducted on a grinding wheel
          before it is fitted to a bench grinder.                                           (2)

2.4       Name TWO safety devices fitted to gas-welding equipment.                          (2)

2.5       State TWO advantages of a workshop with a process layout.                         (2)
                                                                                            [10]

Copyright reserved                                                       Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Automotive           5                              DBE/November 2023
                                           NSC

QUESTION 3: MATERIALS (GENERIC)

3.1       Give ONE reason why the lengths of metals are normally marked or colour-
          coded at the ends.                                                                     (1)

3.2       State ONE property of metals that can be determined by EACH of the
          following tests:

          3.2.1      Sound test                                                                  (1)

          3.2.2      Bending test                                                                (1)

          3.2.3      Machining test                                                              (1)

3.3       Why is metal soaked in heat when performing heat-treatment processes?                  (2)

3.4       State TWO methods of conducting case hardening.                                        (2)

3.5       Explain how steel is annealed during heat-treatment processes.                         (3)

3.6       Name TWO quenching mediums that rapidly cool metal after heat-treatment
          processes.                                                                             (2)

3.7       Which heat-treatment process follows the hardening process of a metal?                 (1)
                                                                                                 [14]

Copyright reserved                                                            Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Automotive            6                            DBE/November 2023
                                            NSC

QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 E.

4.1       Identify the equipment shown in FIGURE 4.1 below.

                                           FIGURE 4.1

          A     Cylinder leakage tester
          B     Compression tester
          C     Fuel pressure tester
          D     Exhaust gas analyser                                                             (1)

4.2       When performing the cylinder leakage test, the piston should be at the top
          dead centre at the end of the …

          A     intake stroke.
          B     compression stroke.
          C     power stroke.
          D     exhaust stroke.                                                                  (1)

4.3       To ensure equal firing periods, the power impulses in an eight-cylinder engine
          should occur every …

          A     30°.
          B     60°.
          C     90°.
          D     120°.                                                                            (1)

Copyright reserved                                                            Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Automotive               7                         DBE/November 2023
                                               NSC

4.4       When balancing the reciprocating mass of an engine, …

          A     the mass of both the crank pin and the big end of the connecting rod are
                taken into consideration.
          B     the mass of the upper third of the connecting rod is taken into
                consideration.
          C     the mass of the lower third of the connecting rod is taken into
                consideration.
          D     the mass of the connecting rod is not taken into consideration.                  (1)

4.5       Engine capacity is the measurement of an engineʹs …

          A     torque.
          B     power.
          C     volume.
          D     mean effective pressure.                                                         (1)

4.6       Work is defined as …

          A     the rotational frequency of a shaft.
          B     a force causing linear movement.
          C     the rate at which power is generated.
          D     the twisting force applied to a rotating shaft.                                  (1)

4.7       What is measured by the dynamometer on an engine?

          A     Indicated power
          B     Brake power
          C     Mean effective pressure
          D     Torque developed                                                                 (1)

4.8       What will the cause be of a worn oil pump?

          A     The pump will work slower.
          B     It will have no effect on the oil pressure.
          C     The oil will become thicker.
          D     The oil pressure will be lower.                                                  (1)

4.9       Why should you be careful when removing a radiator cap when the engine is
          hot?

          A     The cylinder head gasket may blow.
          B     The engine will overheat.
          C     You may burn yourself.
          D     The tester will not have an accurate reading.                                    (1)

Copyright reserved                                                            Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Automotive               8                            DBE/November 2023
                                               NSC

4.10      Stall speed in a torque converter occurs …

          A     when the engine stalls.
          B     when a vehicle drives at the lowest speed before stalling.
          C     just before a vehicle starts moving.
          D     when the turbine and pump rotate at the highest speed and at the same
                speed.                                                                               (1)

4.11      The device that controls the functioning of the electronic automatic
          transmission is the …

          A     power management system.
          B     transmission control unit.
          C     body control unit.
          D     throttle positioning sensor.                                                         (1)

4.12      What is the cause of the tyre wear pattern shown in FIGURE 4.12 below?

                                            FIGURE 4.12

          A     Excessive camber
          B     Excessive toe-in angles
          C     Imbalanced wheel
          D     Over-inflated wheel                                                                  (1)

4.13      Which CORRECT combination of components form part of the distributorless
          ignition system (DIS)?

          A     Electronic control unit, crankshaft position sensor and ignition coil
          B     Electronic control unit, crankshaft position sensor and distributor
          C     Electronic control unit, ignition coil and distributor
          D     Electronic control unit, camshaft position sensor and distributor                    (1)

4.14      Why are the calibration values of the diesel injector loaded into the ECM?

          A     To reduce engine vibrations
          B     To increase fuel usage
          C     To reduce engine speed
          D     To increase the injection duration                                                   (1)
                                                                                                     [14]

Copyright reserved                                                                Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Automotive              9                             DBE/November 2023
                                              NSC

QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)

5.1       Answer the following questions on a compression tester:

          5.1.1       Explain the function of the compression tester.                               (2)

          5.1.2       Give ONE reason for low compression in a cylinder.                            (1)

          5.1.3       Explain the reason why a card-type compression tester would be
                      preferred when performing a compression test.                                 (2)

5.2       FIGURE 5.2 below shows a cylinder leakage tester. Answer the questions
          that follow.

                     Pressure                                                A
                      gauge

                                                 Control valve

                                             FIGURE 5.2

          5.2.1       Explain the function of the cylinder leakage tester.                          (2)

          5.2.2       Identify gauge A.                                                             (1)

          5.2.3       State the use of the control valve.                                           (1)

5.3       When performing the exhaust gas analysis, what unit is used to measure
          EACH of the following gases?

          5.3.1       Carbon dioxide (CO2)                                                          (1)

          5.3.2       Hydrocarbon (HC)                                                              (1)

Copyright reserved                                                               Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Automotive                     10               DBE/November 2023
                                                     NSC

5.4       Give TWO reasons why the pick-up/inlet hose must be removed from the
          exhaust before calibrating an exhaust gas analyser.                                (2)

5.5       Name TWO places inside a car cabin where an OBD-II plug is usually
          located.                                                                           (2)

5.6       State THREE manufacturer's specifications that must be entered into an
          OBD-II scanner before a diagnostic test can be conducted.                          (3)

5.7       What type of wheel balance procedure is described when the wheel stops
          with the heavy spot at the bottom during wheel balancing?                          (1)

5.8       FIGURE 5.8 below shows a bubble gauge. What is measured by
          gauges 1 to 4?

                                    Gauge 1                  Gauge 2
                                                                       Gauge 3

                                     MAGNETIC

                                     BUBBLE GAUGE

                                                       Gauge 4
                                                    FIGURE 5.8                               (4)
                                                                                             [23]

Copyright reserved                                                        Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Automotive             11                           DBE/November 2023
                                             NSC

QUESTION 6: ENGINES (SPECIFIC)

6.1       FIGURE 6.1 below shows the crankshaft of a four-cylinder engine. Answer
          the questions that follow.

                                                     B

                             A

                                                              C
                                                D

                                            FIGURE 6.1

          6.1.1      Label parts A–D.                                                            (4)

          6.1.2      Explain TWO ways of correcting the imbalance of a crankshaft
                     when performing dynamic balancing.                                          (2)

6.2       FIGURE 6.2 below shows a combined rubber and friction disc vibration
          damper used on an internal combustion engine. Answer the questions that
          follow.

                                                          C

                                                          D

                                    B

                                        A

                                            FIGURE 6.2

          6.2.1      Label parts A–D.                                                            (4)

          6.2.2      Where in the engine is the vibration damper fitted?                         (1)

          6.2.3      What is the function of the vibration damper?                               (1)

Copyright reserved                                                            Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Automotive             12                         DBE/November 2023
                                             NSC

6.3       Name TWO engine cylinder configurations.                                              (2)

6.4       How many power strokes per revolution are there for EACH of the following
          four-stroke engines?

          6.4.1      Four-stroke four-cylinder engine                                           (1)

          6.4.2      Four-stroke six-cylinder engine                                            (1)

6.5       FIGURE 6.5 below shows views of the turbine of a turbocharger with the
          vanes closed and open. Answer the questions that follow.

                              Closed                      Open
                                            FIGURE 6.5

          6.5.1      Identify the type of turbocharger.                                         (1)

          6.5.2      Why is a turbocharger able to achieve a boost in engine power?             (2)

          6.5.3      State TWO factors that influence the lifespan and reliability of a
                     turbocharger.                                                              (2)

6.6       State THREE disadvantages of a turbocharger compared to a supercharger.               (3)

6.7       State ONE disadvantage of EACH of the following superchargers:

          6.7.1      Roots supercharger                                                         (1)

          6.7.2      Twin-screw supercharger                                                    (1)

6.8       Give TWO reasons why a vehicle is fitted with both a supercharger and a
          turbocharger on its engine.                                                           (2)
                                                                                                [28]

Copyright reserved                                                           Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Automotive             13                      DBE/November 2023
                                             NSC

QUESTION 7: FORCES (SPECIFIC)

7.1       Explain ONE difference between the indicated power and the brake power of
          an engine.                                                                         (2)

7.2       The bore of a cylinder is 75 mm and the stroke length of the piston is
          80 mm. The compression ratio is 10 : 1.

          Calculate the following:

          7.2.1      The swept volume                                                        (3)

          7.2.2      The clearance volume                                                    (3)

          7.2.3      The new stroke length if the compression ratio is increased to
                     11 : 1. The clearance volume and bore remain unchanged. The
                     answer must be in mm.                                                   (6)

7.3       Describe TWO methods to lower the compression ratio of an engine.                  (2)

7.4       The following data was recorded during a Pröny brake test on a
          four-stroke four-cylinder engine:

          Mean effective pressure:    950 kPa
          Bore diameter:              90 mm
          Stroke length:              85 mm
          Brake arm length:           400 mm
          Scale reading:              30 kg
          Engine speed during test:   2 000 r/min

          Calculate the following:

          7.4.1      The torque developed                                                    (4)

          7.4.2      Brake power in kW                                                       (3)

          7.4.3      Indicated power in kW                                                   (7)

          7.4.4      Mechanical efficiency                                                   (2)
                                                                                             [32]

Copyright reserved                                                        Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Automotive            14                           DBE/November 2023
                                            NSC

QUESTION 8: MAINTENANCE (SPECIFIC)

8.1       Answer the following questions on the exhaust gas analysis:

          8.1.1      How will a leak on the exhaust system, inlet manifold or vacuum
                     system affect the readings?                                                 (2)

          8.1.2      State TWO ideal exhaust gas readings.                                       (2)

8.2       State TWO pre-checks that must be done on a compression tester before
          conducting a compression test on an internal combustion engine.                        (2)

8.3       Tabulate THREE faults and their possible causes when a leak is detected
          during a cylinder leakage test.                                                        (6)

8.4       State THREE manufacturerʹs specifications required when conducting an
          oil-pressure test on an internal combustion engine.                                    (3)

8.5       State FOUR possible causes of a low fuel pressure reading.                             (4)

8.6       Explain step by step how to conduct a pressure test on a radiator cap.                 (4)
                                                                                                 [23]

Copyright reserved                                                            Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Automotive                15                     DBE/November 2023
                                                NSC

QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)

9.1       Explain FOUR reasons why a vehicle fitted with an automatic gearbox would
          be preferred over a vehicle fitted with a manual gearbox.                            (4)

9.2       Describe how a vehicle fitted with an automatic gearbox should be towed over
          a long distance.                                                                     (2)

9.3       FIGURE 9.3 below shows an exploded view of a torque converter. Answer the
          questions that follow.

                                                      Turbine

                                    Pressure      Stator
                      Cover                                 Impeller
                                    plate
                                               FIGURE 9.3

          9.3.1      Describe THREE functions of a torque converter.                           (3)

          9.3.2      Which component prevents slip in a torque converter?                      (1)

Copyright reserved                                                          Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Automotive                 16                   DBE/November 2023
                                                 NSC

9.4       FIGURE 9.4 below shows an exploded view of a brake band in an automatic
          gearbox. Answer the questions that follow.

                             B                                    C
                     A

                                                              D

                                               FIGURE 9.4

          9.4.1          Label parts A–D.                                                     (4)

          9.4.2          What is the function of part D?                                      (1)

          9.4.3          Which component of the automatic gearbox controls the brake
                         band?                                                                (1)

Copyright reserved                                                         Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Automotive            17                          DBE/November 2023
                                            NSC

9.5       FIGURE 9.5 below shows a double epicyclic gear train/system. Answer the
          questions that follow.

                                                  Brake band
                  Annulus A2                                   Annulus A1

                                                               Planet carrier

              Input shaft

                                                                 Output shaft

               Sun gear S2                                   Sun gear S1

                                                        Planetary gear P1
               Planetary gear P2

                                           FIGURE 9.5

          9.5.1       Which gear is selected when sun gears S1 and S2 are driven by the
                      engine while annulus A1 is held stationary?                               (1)

          9.5.2       Which gear is selected when sun gears S1 and S2 are driven by the
                      engine while annulus A2 is held stationary?                               (1)
                                                                                                [18]

Copyright reserved                                                           Please turn over

### Page 18

Downloaded from hlayiso.com
Mechanical Technology: Automotive            18                          DBE/November 2023
                                            NSC

QUESTION 10:         SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY
                     AND ELECTRONICS) (SPECIFIC)

10.1      Explain the function of a steering mechanism.                                         (2)

10.2      State TWO signs of an unbalanced wheel on a vehicle.                                  (2)

10.3      Describe how static wheel balance is done and how an imbalanced
          wheel can be corrected.                                                               (4)

10.4      FIGURE 10.4 below shows a sketch of a wheel alignment angle.
          Label A–D.

                                             C
                         B                                       D

                                                          Front of vehicle

                         A

                                                      Road surface

                                          FIGURE 10.4                                           (4)

10.5      Explain TWO advantages of an electric fuel pump fitted on a vehicle.                  (2)

10.6      State the purpose of EACH of the following components fitted to the fuel
          delivery system:

          10.6.1     Pressure regulator                                                         (1)

          10.6.2     Fuel filter                                                                (1)

Copyright reserved                                                           Please turn over

### Page 19

Downloaded from hlayiso.com
Mechanical Technology: Automotive               19                           DBE/November 2023
                                               NSC

10.7      FIGURE 10.7 below shows an air-induction system. Answer the questions
          that follow.

                                             Air-intake chamber
                                         C                                     D

                   B

                              A

                                             FIGURE 10.7

          10.7.1       Label A–D.                                                                (4)

          10.7.2       What is the purpose of the air-induction system fitted on an internal
                       combustion engine?                                                        (2)

10.8      What is the purpose of the lambda sensor in an exhaust system?                         (2)

10.9      Draw TWO neat labelled sketches to show the two different stator winding
          connections in an alternator.                                                          (4)

10.10     State TWO methods to increase the output of an alternator.                             (2)

10.11     Explain TWO main aims of an adaptive speed control fitted to a vehicle.                (2)
                                                                                                 [32]

                                                                                   TOTAL:        200

Copyright reserved

### Page 20

Downloaded from hlayiso.com
Mechanical Technology: Automotive              1                       DBE/November 2023
                                              NSC

        FORMULA SHEET FOR MECHANICAL TECHNOLOGY: AUTOMOTIVE

   1.          F  ma

              Where:
                        m = Mass
                        a = Acceleration

   2.          Work done = Force × Displacement         OR        W Fs

                          Force  Displacement                         Fs
   3.          Power                                   OR        P
                                  Time                                  t

   4.          Torque  Force  Radius                  OR        T Fr

   5.          IP  P  L  A  N  n

               Where:

                       IP  Indicated power
                        P  Mean effective pressure
                        L  Stroke length
                        A  Area of piston crown
                        N  Number of power strokes per second
                        n  Number of cylinders

   6.          BP = 2 π N T

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     T  Torque

   7.          Brake power with Pröny brake = 2  π  N  F  R

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     F  Force
                     R  Brake arm length

Copyright reserved                                                       Please turn over

### Page 21

Downloaded from hlayiso.com
Mechanical Technology: Automotive                 2                DBE/November 2023
                                                 NSC

                                          BP
   8.          Mechanical efficiency =        100%
                                          IP

                                       SV  CV
   9.          Compression ratio 
                                         CV

               Where:

                     SV  Swept volume
                     CV  Clearance volume

                    πD 2
   10.         SV =      L
                     4

               Where:
                     D  Bore diameter
                     L  Stroke length

                        SV
   11.         CV =
                       CR - 1

                                Product of teeth on driven gears
   12.         Gear ratio =
                                Product of teeth on driver gears

Copyright reserved

## Related documents

- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-afr/cad6695c-dbf0-406d-a72d-78edaf6ce649) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Fitting & Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-fitting-machining-afr/13f8ed56-a4ef-4858-8d10-2d07c992e826) — Mechanical Technology · QP · 2023 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
