# Mechanical Technology Grade 12 NSC November 2023 Memo (Eng)

> Grade 12 Mechanical Technology memorandum from the NSC November Exam 2023 (English), 23 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-mg-eng/0c627e9c-18b2-4a14-b5c6-7ec94aac216a
- Updated: 2026-10-29
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2023
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 23

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC November 2023 Memo (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-mg-eng/0c627e9c-18b2-4a14-b5c6-7ec94aac216a)

## About this document

Mechanical Technology · Grade 12 · NSC November Exam · 2023. Memorandum. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

                     MECHANICAL TECHNOLOGY: AUTOMOTIVE

                                  NOVEMBER 2023

                               MARKING GUIDELINES

MARKS: 200

                      These marking guidelines consist of 23 pages.

Copyright reserved                                                    Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Automotive           2                  DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 1: MULTIPLE-CHOICE (GENERIC)

1.1       B                                                                    (1)

1.2       A                                                                    (1)

1.3       C                                                                    (1)

1.4       C                                                                    (1)

1.5       A                                                                    (1)

1.6       B                                                                    (1)
                                                                                [6]

Copyright reserved                                                 Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Automotive           3                       DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 2: SAFETY (GENERIC)

2.1       Examination checks:
           Severe bleeding 
           Internal bleeding 
           Head injuries 
           Neck injuries 
           Fractures 
           Vital signs 
           Physical abnormalities 
                                                                        (Any 2 x 1)     (2)

2.2       Safety devices on the power-driven guillotine:
           Finger protectors / Fixed guards / Blade guard 
           Rear view mirrors 
           Rear light curtains 
           Automatic sweep-away 
           Revolving warning lights 
           Two-hand / dual control device 
           Additional emergency buttons 
           Self-adjusting guards 
           Covered footswitch 
                                                                        (Any 2 x 1)     (2)

2.3       Grinding wheel:
           The wheel should be rated above the speed of the motor. 
           Check for cracks on the grinding wheel. 
           Check for chips on the grinding wheel. 
           Check that the arbor hole is the correct size. 
           Must not be contaminated by oil/fluids or grease. 
           Correct size of the wheel. 
           Correct type of wheel for the material. 
                                                                        (Any 2 x 1)     (2)

2.4       Gas welding equipment – safety devices:
           Valve guard 
           Flash back arrestor 
           Pressure regulator 
           C-clamps on hoses/Parallel hose clips 
           Acetylene spindle key must always be in place. 
           Cylinder valves. 
                                                                        (Any 2 x 1)     (2)

Copyright reserved                                                         Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Automotive           4                  DBE/November 2023
                                    NSC – Marking Guidelines

2.5       Advantages of process layout of machines are:
           High machine utilisation. 
           Better supervision. 
           Less interruption in the flow of work. 
           Lower equipment costs. 
           Better control of total manufacturing costs. 
           Greater flexibility. 
                                                               (Any 2 x 1)      (2)
                                                                                [10]

Copyright reserved                                                 Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Automotive           5                            DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 3: MATERIALS (GENERIC)

3.1      Colour code of metal:
          To identify the type of metal. 
          To identify carbon content especially after the metal was stored. 
          To identify the profile/size of the metal. 
                                                                         (Any 1 x 1)       (1)

3.2       Tests to determine properties of steel:

          3.2.1      Sound test:
                      Hardness 
                      Softness 
                                                                          (Any 1 x 1)      (1)

          3.2.2      Bending test:
                      Ductility 
                      Bend strength 
                      Fracture strength 
                      Resistance to fracture
                      Brittleness 
                      Elasticity 
                      Plasticity 
                      Flexibility 
                                                                          (Any 1 x 1)      (1)

          3.2.3      Machining test:
                      Hardness 
                      Strength 
                                                                          (Any 1 x 1)      (1)

3.3      Reasons metal soaked during heat treatment:
          To ensure uniform heat distribution  throughout the metal. 
          To achieve a uniform grain structure  after cooling the metal. 
                                                                        (Any 1 x 2)        (2)

3.4      Case hardening:
          Carburising 
          Nitriding 
          Cyaniding 
                                                                          (Any 2 x 1)      (2)

3.5       Annealing process:
          Heating the steel slightly above AC3, (upper critical temperature)  soaking
          it for a required time/period  and then slow cooling  back to room
          temperature.                                                                     (3)

Copyright reserved                                                            Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Automotive           6                  DBE/November 2023
                                    NSC – Marking Guidelines

3.6      Rapid quenching mediums:
          Brine/Salt water 
          Water 
          Nitrogen 
          Oil 
                                                                (Any 2 x 1)     (2)

3.7       Heat treatment process:
          Tempering                                                            (1)
                                                                                [14]

Copyright reserved                                                 Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Automotive           7                  DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 4: MULTIPLE-CHOICE (SPECIFIC)

4.1       B                                                                    (1)

4.2       B                                                                    (1)

4.3       C                                                                    (1)

4.4       B                                                                    (1)

4.5       C                                                                    (1)

4.6       B                                                                    (1)

4.7       B                                                                    (1)

4.8       A or D                                                               (1)

4.9       C                                                                    (1)

4.10      C                                                                    (1)

4.11      B                                                                    (1)

4.12      D                                                                    (1)

4.13      A                                                                    (1)

4.14      A                                                                    (1)
                                                                                [14]

Copyright reserved                                                 Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Automotive           8                          DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)

5.1       Compression tester:

          5.1.1      Function of the compression tester:
                      It measures the pressure created  when the piston is at top
                       dead centre on the compression stroke. 
                      It is used to determine the condition of the piston
                       rings after a wet compression test. 
                                                                       (Any 1 x 2)      (2)

          5.1.2      Reasons for low compression:
                      Worn cylinders 
                      Worn piston rings 
                      Worn piston 
                      Leaking inlet valve 
                      Leaking exhaust valve 
                      Leaking cylinder head gasket 
                      Cracked cylinder head 
                      Cracked piston / Damaged piston. 
                      Piston ring groove worn out and not holding pressure. 
                      Insufficient volumetric efficiency. 
                      Cracked cylinder sleeve. 
                                                                        (Any 1 x 1)     (1)

          5.1.3      Card-type compression tester:
                      The compression tester automatically records  the readings
                       on the card in the tester. 
                      To eliminate the human error  that can be made when
                       taking the readings,  in terms of estimations.
                                                                       (Any 1 x 2)      (2)

5.2       Cylinder leakage tester:

          5.2.1      Function:
                      To check where the combustion chamber/cylinder leaks
                       gases  during compression stroke. 
                      To determine the percentage  pressure loss  from the
                       combustion chamber.
                                                                   (Any 1 x 2)          (2)

          5.2.2      Gauge A:
                     Percentage leakage (%) / Pressure leakage gauge                   (1)

          5.2.3      Control valve:
                      Used to calibrate the cylinder leakage tester. 
                      Regulates the air pressure entering the cylinder leakage
                       tester. 
                                                                        (Any 1 x 1)     (1)

Copyright reserved                                                         Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Automotive           9                            DBE/November 2023
                                    NSC – Marking Guidelines

5.3       Exhaust gas analysis unit of measure:

          5.3.1      Carbon dioxide (CO2):
                     Percentage (%)                                                       (1)

          5.3.2      Hydrocarbon (HC):
                     Parts per million (ppm)                                              (1)

5.4       Reason for removing pick-up hose:
           For auto-zero on the analyser to start at zero. / Calibration of tester to
            zero. 
           For exhaust gases to get out of the hose.                                     (2)

5.5       OBD-II plug location:
           At the glove compartment (cubby hole). 
           Under the dashboard by the driver. 
           Behind a trim panel. 
           Between the front seats. 
           By the ashtray. 
           The floor panel. 
           In the fuse box. 
                                                                          (Any 2 x 1)      (2)

5.6       Information typed into the diagnostic scanner:
           The vehicle identification number (VIN). 
           The make of the vehicle. 
           The model of the vehicle. 
           The engine type. 
                                                                          (Any 3 x 1)      (3)

5.7       Wheel balancing:
          Static                                                                            (1)

5.8       Label the bubble gauge:
          Gauge 1 - Zero scale/level 
          Gauge 2 - Castor 
          Gauge 3 - King pin inclination 
          Gauge 4 - Camber                                                                (4)
                                                                                           [23]

Copyright reserved                                                            Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Automotive          10                            DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 6: ENGINES (SPECIFIC)

6.1       Crankshaft of a four-cylinder engine:

          6.1.1      Label the crank shaft:
                     A – Crank nose/vibration damper mounting 
                     B – Main journals 
                     C – Big-end journals / Crankpin journals 
                     D – Counterweight/Crank web                                         (4)

          6.1.2      Correcting crank shaft imbalance:
                      By removing metal/weight from the crank webs. 
                      By adding metal/weight to the crank webs.                         (2)

6.2       Vibration dampers:

          6.2.1      Label:
                     A – Friction disc 
                     B – Crankshaft 
                     C – Secondary flywheel 
                     D – Rubber cushion                                                  (4)

          6.2.2      Location:
                     Fitted to the front end/nose of the crankshaft.                     (1)

          6.2.3      Function:
                      To smooth out / absorb/ minimize the engine vibrations. 
                      To counteract the torsion of the crankshaft. 
                                                                        (Any 1 x 1)       (1)

6.3       Engine configurations:
           Inline / Straight 
           V-engine 
           W-engine / Double V-engine 
           Horizontally opposed engine / Flat engine / Boxer engine 
           Radial engine 
           X-Engine 
           U-engine 
           Delta engine 
           K-engine 
           Opposed-piston engine 
                                                                          (Any 2 x 1)     (2)

Copyright reserved                                                           Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Automotive           11                           DBE/November 2023
                                     NSC – Marking Guidelines

6.4       Power strokes per revolution:

          6.4.1      Four-cylinder:
                     2                                                                    (1)

          6.4.2      Six-cylinder:
                     3                                                                    (1)

6.5       Turbo-chargers:

          6.5.1      Type:
                     Variable geometry turbo-charger                                      (1)

          6.5.2      Reason turbocharger boosts:
                      It increases  volumetric efficiency  of the cylinders.
                      It increases  the pressure of the air  entering the cylinder.
                                                                           (Any 1 x 2)     (2)

          6.5.3      Influence on the lifespan:
                      The oil supply is clean. 
                      Use of the correct grading/type of oil. 
                      The exhaust gas does not become overheated. 
                      Adopting the proper switch-off procedure. 
                      Sufficient oil pressure. 
                                                                          (Any 2 x 1)      (2)

6.6       Disadvantages of a turbo-charger:
           It requires pressure lubrication for high-speed bearings. 
           It requires pressure lubrication to act as a coolant. 
           It suffers from lag. 
           It tends to heat the air, reducing its density. 
           It needs to be controlled from over-revving by the waste gate. 
           Some require a special shut-down procedure before the engine can be
             switched off. 
                                                                         (Any 3 x 1)       (3)

6.7       Disadvantage of superchargers:

          6.7.1      Roots supercharger:
                      The least efficient supercharger. 
                      They add more weight to the vehicle. 
                      Usually large/bonnet(hood) must be modified. 
                      They move air in bursts. 
                                                                          (Any 1 x 1)      (1)

          6.7.2      Twin-screw supercharger:
                      They are expensive. 
                      They require more precision manufacturing. 
                                                                          (Any 1 x 1)      (1)

Copyright reserved                                                            Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Automotive          12                         DBE/November 2023
                                    NSC – Marking Guidelines

6.8       Reasons for a supercharger with a turbocharger on its engine:
           To overcome lag at low rpm. 
           To increase power at all rpm. 
           Outstanding fuel economy. 
           To increase torque at all rpm. 
           Reduces the parasitic effect/power sapping on the engine. 
                                                                        (Any 2 x 1)     (2)
                                                                                        [28]

Copyright reserved                                                         Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Automotive          13                              DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 7: FORCES (SPECIFIC)

7.1                 Indicated power:                           Brake power
             Calculated using the volume and         Calculated using the      torque
              the indicated mean effective             developed. 
              pressure. 
             Indicated power is the theoretical      Brake power is the actual power
              power.                                  output of an engine. 
             Indicated power is calculated           Calculated considering
              without     considering       any        mechanical or other losses of the
              mechanical or other losses of the        engine. 
              engine. 
                                                                            (Any 1 x 2)      (2)

7.2       Calculations:

          7.2.1      Swept volume:

                                    π  D2
                     Swept volume         L
                                       4
                                         π  7,5 2 
                                                   8 
                                             4
                                      353,43 cm 3                                          (3)

          7.2.2      Original clearance volume:
                              SV
                     CV =
                           (CR - 1)
                           353,43 
                         =
                           (10 - 1) 
                          = 39,27 cm3                                                       (3)

Copyright reserved                                                              Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Automotive          14                                   DBE/November 2023
                                    NSC – Marking Guidelines

         7.2.3       Stroke length:
                     SV = CV(CR - 1)
                         = 39,27(11 - 1) 
                         = 392,7cm3 

                                            π  D2                              7,52
                       Swept volume               L                Area 
                                               4                                  4
                                             SV                               44,18 cm2 
                                     L          
                                            Area
                                            392,70
                                                  
                                             44,18
                                         8,89 cm  10
                                         88,89 mm                                                (6)

7.3       Methods to lower the compression:
           Fit thicker gasket between cylinder block and cylinder head. 
           Fit a shim between cylinder block and cylinder head. 
           Fit piston with suitable lower crowns. 
           Fit crankshaft with shorter stroke (with suitable connecting rods). 
           Decrease bore diameter. 
                                                                           (Any 2 x 1)            (2)

7.4       Prony brake test:

          7.4.1      Torque:
                     Torque = Force  radius
                                          400
                     Torque = (30  10)                    (g = 10 m/s2)
                                         1000
                            = 120 Nm 

                                                        OR

                                            400 
                     Torque = (30  9,81)                   (g = 9, 81 m/s2)
                                           1000
                            = 117,72 Nm    
                                                                                                  (4)

Copyright reserved                                                                   Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Automotive          15                                  DBE/November 2023
                                    NSC – Marking Guidelines

          7.4.2      Brake power:
                     BP  2 NT
                                      
                                   2000                      (g = 10 m/s2)
                         2            120 
                                   60 
                          25,13 kW 

                                                       OR

                     BP  2 NT
                                      
                                   2000 
                         2            117,72           (g = 9, 81 m/s2)
                                   60 
                          24,66 kW                                                              (3)

          7.4.3      Indicated power:
                           IP  PLANn
                     Where P  950  10 3 Pa

                                 85
                            L
                                1000
                               0,085 m 

                                 π  0,09 2  
                           A              
                                             
                                     4      
                               6,36  10 3 m 2 

                                 2000
                            N         
                                60  2
                               16,67 pow er strokes per second 

                            n4

                           IP (950  10 3 )  0,085 (6,36  10 -3 )  16,67   4 
                               34,24 kW                                                         (7)

Copyright reserved                                                                   Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Automotive          16                           DBE/November 2023
                                    NSC – Marking Guidelines

          7.4.4      Mechanical efficiency:
                          BP
                     ME      100
                          IP
                          25,13
                                 100             (g = 10 m/s2)
                          34,24
                         73,39 % 

                                                     OR
                           BP
                     ME       100
                           IP
                           24,66                     (g = 9, 81 m/s2)
                                   100
                           34,24
                          72,02 %                                                      (2)
                                                                                         [32]

Copyright reserved                                                          Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Automotive          17                              DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 8: MAINTENANCE (SPECIFIC)

8.1       Exhaust gas analysis:

          8.1.1      Readings caused by a leak:
                      Incorrect  readings 
                      No  readings at all 
                                                                            (Any 1 x 2)        (2)

          8.1.2      Ideal exhaust gas readings:
                      Low carbon monoxide 
                      High carbon dioxide 
                      Low Hydrocarbon 
                                                                            (Any 2 x 1)        (2)

8.2       Compression tester:
           Ensure that the tester can handle the pressure you want to test. 
           Ensure the rubber pipes are not perished. 
           Ensure the relief valve is working on the tester. / Zero the tester. 
           Ensure you use the correct adapter for the plug hole. 
                                                                            (Any 2 x 1)        (2)

8.3       Cylinder leakage test:
                          Fault                               Possible cause
           Hissing noise at air intake.             Leaking inlet valve. 
           Hissing noise at exhaust.                Leaking exhaust valve. 
           Hissing noise at oil filler               Piston rings are worn. 
             cap/dipstick. 
           Bubbles in the radiator.                 Blown        cylinder       head
                                                       gasket/Cracked cylinder head. 
             Hissing sound from adjacent             Blown cylinder head gasket
              spark plug hole                         between cylinders / crack
                                                       between cylinders. 
                                                                             (Any 3 x 2)       (6)

8.4       Oil pressure test:
           Oil pressure when engine is idling. 
           Oil pressure when engine is cold. 
           Oil pressure when engine is hot. 
           Oil pressure on high revolutions. 
                                                                            (Any 3 x 1)        (3)

Copyright reserved                                                                Please turn over

### Page 18

Downloaded from hlayiso.com
Mechanical Technology: Automotive          18                           DBE/November 2023
                                    NSC – Marking Guidelines

8.5       Fuel pressure:
           Faulty fuel pump 
           Blocked fuel filter 
           Cracked fuel line 
           Clogged pump strainer 
           Low voltage to the fuel pump 
           Faulty fuel pressure regulator 
           Empty fuel tank 
           Faulty fuel pump relay 
           Leaking fuel injectors 
           Blocked fuel line 
                                                                         (Any 4 x 1)      (4)

8.6       Radiator cap pressure test:
          Step 1: Obtain the release pressure on the cap or from manufacturer’s
                   specifications. 
          Step 2: Fit the radiator cap with the correct adaptor on the cooling system
                   pressure tester. 
          Step 3: Now pump the tester while watching the release pressure on the
                   gauge. 
          Step 4: Check that the cap holds the specified pressure.                       (4)
                                                                                           [23]

Copyright reserved                                                           Please turn over

### Page 19

Downloaded from hlayiso.com
Mechanical Technology: Automotive          19                             DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)

9.1       Reasons for automatic gearbox preferred over manual gearbox:
           There is no clutch pedal. (relieve the driver of clutch operation). 
           There is no need to change gears. (relieve the driver of gearshift
            operation). 
           Allows the driver to concentrate on driving. 
           Smoother and easier driving of the vehicle. 
           It reduces driving fatigue. 
           It ensures great reduction of wheel spin. 
           The vehicle can be stopped suddenly without the engine stalling. 
           The system dampens all engine torsional vibrations. 
                                                                            (Any 4 x 1)     (4)

9.2       Towing vehicle with automatic gearbox:
           The drive wheels must be lifted off the ground. 
           The vehicle  should be lifted on a flatbed tow truck. 
           The drive shaft/propeller  shaft should be removed.
                                                                           (Any 1 x 2)      (2)

9.3       Torque converter:

          9.3.1      Functions:
                      It transfers the torque and power from the engine to the
                       gearbox. 
                      It drives the front pump of the gearbox. 
                      It isolates the engine from the gearbox when the vehicle is
                       stationary. 
                      It multiplies the torque of the engine. 
                      Reduction of engine vibrations transmitted to the gearbox. 
                      Turn the engine during the idle strokes. (flywheel effect) 
                                                                          (Any 3 x 1)       (3)

          9.3.2      Component that prevents slip:
                     Pressure plate/Clutch assembly                                        (1)

Copyright reserved                                                             Please turn over

### Page 20

Downloaded from hlayiso.com
Mechanical Technology: Automotive          20                  DBE/November 2023
                                    NSC – Marking Guidelines

9.4       Brake band in automatic gearbox:

          9.4.1      Label:
                     A – Band adjuster 
                     B – Anchor 
                     C – Lever 
                     D – Brake band                                            (4)

          9.4.2      Function of brake band:
                     The brake band holds the drum/annulus in a stationary
                     position.                                                 (1)

          9.4.3      Component controlling the brake band:
                     Hydraulic piston                                          (1)

9.5       Double epicyclic gear train:

          9.5.1      First (1st) gear / Gear reduction                         (1)

          9.5.2      Second (2nd) gear / Overdrive                             (1)
                                                                                [18]

Copyright reserved                                                 Please turn over

### Page 21

Downloaded from hlayiso.com
Mechanical Technology: Automotive          21                             DBE/November 2023
                                    NSC – Marking Guidelines

QUESTION 10: SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY
AND ELECTRONIC) (SPECIFIC)

10.1      Steering mechanism:
          The steering mechanism must enable the driver  to be in control of the
          path taken by the vehicle at all times.                                          (2)

10.2      Signs of wheel imbalance:
           Excessive tyre wear 
           A poor ride/tracking 
           Vibrations on the steering wheel 
           Wheel bounce/hop 
           Wheel shimmy/wobble 
           Vibrations on the brake pedal 
           Excessive wear on the suspension 
                                                                           (Any 2 x 1)      (2)

10.3      Static wheel balance:
           Mount the wheel so that it is free to turn on a spindle through its
             center. 
           The spindle must be approximately horizontal and the wheel turning
             slowly. 
           If the wheel is out of balance, it will always come to rest with one point,
             the ‘heavy spot’, at the bottom. 
           To correct static imbalance, a small mass (weight) is applied to the
             wheel rim, diametrically opposite the ‘heavy spot’. The size and position
             of the weight to be fitted are found by trial and error.                      (4)

10.4      Negative caster angle:
          A - Kingpin 
          B - Perpendicular line 
          C - Negative caster angle 
          D - Centre line of kingpin                                                       (4)

10.5      Electric fuel pump:
           Immediate supply of fuel when the ignition switch is turned on. 
           Low operation noise. 
           Less discharge pulsation of fuel. 
           Compact and light design. 
           It helps to prevent fuel leak. 
           It reduces vapour lock. 
           Delivers fuel at a higher rate / pressure. 
                                                                         (Any 2 x 1)        (2)

Copyright reserved                                                             Please turn over

### Page 22

Downloaded from hlayiso.com
Mechanical Technology: Automotive           22                              DBE/November 2023
                                     NSC – Marking Guidelines

10.6      Fuel delivery system:

          10.6.1     Pressure regulator:
                      It keeps the pressure in the rail at a specified value. 
                      It regulates the pressure in the rail. 
                                                                            (Any 1 x 1)       (1)

          10.6.2     Fuel filter:
                      Prevents dirt from entering the fuel line. 
                      Prevents damaging or clogging of the injectors. 
                      Prevents damage to the pressure regulator. 
                                                                             (Any 1 x 1)      (1)

10.7      Air induction system:

          10.7.1     Label:
                     A - MAF sensor 
                     B - Air filter/Air filter housing 
                     C - Throttle valve / Throttle body 
                     D - Intake valve                                                        (4)

          10.7.2     Purpose:
                     The air-induction system measures  and controls the air
                     required for the combustion.                                            (2)

10.8      Purpose of lambda sensor:
          The sensor measures the oxygen content in the flow of the exhaust
          gas  and then sends a signal to the engine control unit.                          (2)

10.9      Stator windings:

                                    (Sketch )                            (Sketch )

                         Delta                             Star- or Y-connected             (4)

10.10     Increase the output frequency:
           Increase the turns of wire/windings on the stationary coil/stator. 
           Increase the strength of the magnetic fields. 
           Increase the rotational frequency at which the magnets rotate. 
                                                                           (Any 2 x 1)        (2)

Copyright reserved                                                               Please turn over

### Page 23

Downloaded from hlayiso.com
Mechanical Technology: Automotive          23                        DBE/November 2023
                                    NSC – Marking Guidelines

10.11     Adaptive speed control:
           To maintain a speed as set by the driver. 
           To adapt this speed and maintain a safe distance from the vehicle in
            front. 
           To provide a warning if there is a risk of a collision. 
           To provide a warning if the set speed is exceeded. 
           Reduces driver fatigue. 
           Improves fuel consumption. 
                                                                      (Any 2 x 1)    (2)
                                                                                     [32]

                                                                         TOTAL:      200

Copyright reserved

## Related documents

- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-afr/cad6695c-dbf0-406d-a72d-78edaf6ce649) — Mechanical Technology · QP · 2023 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-afrikaans/f45c553c-63a1-4e1c-b9c6-d426a3dfef26) — Mechanical Technology · Memo · 2023 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — QP · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
