# Mechanical Technology Grade 12 NSC November 2023 QP (Eng)

> Grade 12 Mechanical Technology question paper from the NSC November Exam 2023 (English), 25 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-eng/986af80b-0295-4740-ac75-856743d92a2f
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2023
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 25

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC November 2023 QP (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-eng/986af80b-0295-4740-ac75-856743d92a2f)

## About this document

Mechanical Technology · Grade 12 · NSC November Exam · 2023. Question paper, 25 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

           MECHANICAL TECHNOLOGY: FITTING AND MACHINING

                                NOVEMBER 2023

MARKS: 200

TIME: 3 hours

        This question paper consists of 19 pages and a 6-page formula sheet.

Copyright reserved                                                   Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining    2                          DBE/November 2023
                                               NSC

INSTRUCTIONS AND INFORMATION

1.         Write your centre number and examination number in the spaces provided on
           the ANSWER BOOK.

2.         Read ALL the questions carefully.

3.         Answer ALL the questions.

4.         Number the answers correctly according to the numbering system used in this
           question paper.

5.         Start EACH question on a NEW page.

6.         Show ALL calculations and units. Round off final answers to TWO decimal
           places.

7.         Candidates may use non-programmable scientific calculators and drawing
           instruments.

8.         The value of gravitational acceleration should be taken as 9,81 m/s2 or
           10 m/s2.

9.         ALL dimensions are in millimetres, unless stated otherwise in the question.

10.        Write neatly and legibly.

11.        A formula sheet is attached at the end of the question paper.

12.        Use the criteria below to assist you in managing your time.

                                                                                 TIME IN
QUESTION                            CONTENT                       MARKS
                                                                                MINUTES
                                 GENERIC
      1         Multiple-choice Questions                           6                6
      2         Safety                                              10               10
      3         Materials                                           14               14
                                 SPECIFIC
       4        Multiple-choice Questions                            14              10
       5        Terminology (Lathe and Milling Machine)              18              20
       6        Terminology (Indexing)                               28              25
       7        Tools and Equipment                                  13              10
       8        Forces                                               33              33
       9        Maintenance                                          18              12
      10        Joining Methods                                      18              12
      11        Systems and Control (Drive Systems)                  28              28
                                                     TOTAL          200             180

Copyright reserved                                                              Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     3                          DBE/November 2023
                                                NSC

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E.

1.1       Who is responsible for safe working conditions in the workplace?

          A   Workersʹ union
          B   Employer
          C   Employee
          D   Department of Labour                                                                 (1)

1.2       Identify the Act that seeks to protect the worker from physical injuries in the
          workplace:

          A   Occupational Health and Safety Act (OHSA), 1993 (Act 85 of 1993)
          B   Labour Relations Act (LRA), 1995 (Act 66 of 1995)
          C   Employment Equity Act (EEA), 1998 (Act 55 of 1998)
          D   Basic Conditions of Employment Act (BCEA), 1997 (Act 75 of 1997)                     (1)

1.3       Which safety precaution must be applied when arc welding?

          A     Wet the work piece before welding to prevent overheating.
          B     Do not let oil and grease come into contact with the oxygen fittings.
          C     Use completely insulated electrode holders.
          D     Ensure that you always open the acetylene valve slowly.                            (1)

1.4       Identify the test shown in FIGURE 1.4 below.

                                               FIGURE 1.4

          A     Sound test
          B     Ultrasonic test
          C     Spark test
          D     Cutting test                                                                       (1)

Copyright reserved                                                              Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     4                    DBE/November 2023
                                                NSC

1.5       Which heat-treatment process relieves the internal stresses produced by
          machining, forging and welding?

          A     Normalising
          B     Case hardening
          C     Tempering
          D     Hardening                                                                   (1)

1.6       FIGURE 1.6 below shows the changes in metal structures during the
          annealing process. What change is indicated at Y?

                                                       Y

                                               FIGURE 1.6

          A     Recovery
          B     Grain growth
          C     Recrystallisation
          D     Grain crystallisation                                                       (1)
                                                                                            [6]

QUESTION 2: SAFETY (GENERIC)

2.1       State TWO checks that must be done on injured persons before removing
          them from a danger zone.                                                          (2)

2.2       Name TWO safety devices fitted to power guillotines.                              (2)

2.3       State TWO safety precautions that must be conducted on a grinding wheel
          before it is fitted to a bench grinder.                                           (2)

2.4       Name TWO safety devices fitted to gas-welding equipment.                          (2)

2.5       State TWO advantages of a workshop with a process layout.                         (2)
                                                                                            [10]

Copyright reserved                                                       Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining    5                          DBE/November 2023
                                               NSC

QUESTION 3: MATERIALS (GENERIC)

3.1       Give ONE reason why the lengths of metals are normally marked or colour-
          coded at the ends.                                                                     (1)

3.2       State ONE property of metals that can be determined by EACH of the
          following tests:

          3.2.1       Sound test                                                                 (1)

          3.2.2       Bending test                                                               (1)

          3.2.3       Machining test                                                             (1)

3.3       Why is metal soaked in heat when performing heat-treatment processes?                  (2)

3.4       State TWO methods of conducting case hardening.                                        (2)

3.5       Explain how steel is annealed during heat-treatment processes.                         (3)

3.6       Name TWO quenching mediums that rapidly cool metal after heat-treatment
          processes.                                                                             (2)

3.7       Which heat-treatment process follows the hardening process of a metal?                 (1)
                                                                                                 [14]

Copyright reserved                                                            Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     6                       DBE/November 2023
                                                NSC

QUESTION 4: MULTIPLE-CHOICE (SPECIFIC)

Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in your ANSWER BOOK, e.g. 4.15 E.

4.1       Identify the type of tool in FIGURE 4.1 below.

                                               FIGURE 4.1

          A     Vernier height gauge
          B     Screw-cutting dial gauge
          C     Centre gauge
          D     Thread-pitch gauge                                                              (1)

4.2       Which ONE of the following is an advantage of cutting tapers on a lathe, using
          the compound slide method?

          A     Tapers with large angles can be cut.
          B     The automatic feed of the machine can be used.
          C     Long tapers can be cut.
          D     It causes the operator to become fatigued.                                      (1)

4.3       Which part(s) of the dividing head is used to set the distances between the
          holes on the index plate?

          A     Sector arms
          B     Crank handle
          C     Index plates
          D     Change gears                                                                    (1)

Copyright reserved                                                           Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     7                             DBE/November 2023
                                                NSC

4.4       Identify the part of a CNC milling machine in FIGURE 4.4 below.

                                               FIGURE 4.4

          A     Tool chuck
          B     Turret
          C     Tool magazine
          D     Tool shelf                                                                           (1)

4.5       Which hardness tester uses a diamond cone to indent material?

          A     Moment hardness tester
          B     Tensile hardness tester
          C     Brinell hardness tester
          D     Rockwell hardness tester                                                             (1)

4.6       Identify part A of the screw thread micrometer shown in FIGURE 4.6 below.

                                                             A

                                               FIGURE 4.6

          A     Ratchet
          B     Lock
          C     Thimble
          D     Anvil                                                                                (1)

4.7       What does the term stress mean?

          A     It is an indication of the reluctance of a body to move.
          B     It is the internal resistance in a body to an external load.
          C     It is an external force acting upon matter.
          D     It is the change in length of a material under a load.                               (1)

Copyright reserved                                                                Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     8                       DBE/November 2023
                                                NSC

4.8       FIGURE 4.8 below shows the different stages of a pop rivet during the riveting
          process. Identify the type of force that is exerted onto the casing of the pop
          rivet.

                                               FIGURE 4.8

          A     Compressive force
          B     Shear force
          C     Tensile force
          D     Pushing force                                                                     (1)

4.9       … is used to strengthen fibreglass when used for boats and motor vehicle
          bodies.

          A     Pigment
          B     Glass
          C     Polyester resin
          D     Glue                                                                              (1)

4.10      Identify the material that bushes are made of:

          A     PVC
          B     Fibreglass
          C     Wood
          D     Vesconite                                                                         (1)

4.11      What is the included angle of a metric V-screw thread?

          A     90°
          B     60°
          C     29°
          D     55°                                                                               (1)

4.12      Identify the type of screw thread that produces a faster movement:

          A     Multiple-start screw thread
          B     V-screw thread
          C     Square thread
          D     Acme screw thread                                                                 (1)

Copyright reserved                                                             Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     9                 DBE/November 2023
                                                NSC

4.13      Identify the type of gear system in FIGURE 4.13 below.

                                               FIGURE 4.13

          A     Spur gear system
          B     Helical gear system
          C     Rack and pinion gear system
          D     Worm gear system                                                         (1)

4.14      Pneumatics uses compressed … to operate equipment.

          A     oil
          B     water
          C     nitrogen
          D     air                                                                      (1)
                                                                                         [14]

Copyright reserved                                                    Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      10                        DBE/November 2023
                                                 NSC

QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)
5.1       State TWO disadvantages of cutting tapers on a centre lathe machine using
          the compound slide method.                                                              (2)
5.2       FIGURE 5.2 below shows a diagram of a taper with an included angle of 8°,
          which should be machined between two centres.

                              85                        l              35

            Ø 78                                                                 Ø 55
                                                              8°

                                               FIGURE 5.2
          5.2.1       Calculate the length of the taper.                                          (4)
          5.2.2       Calculate the set-over of the tailstock required to cut the taper in
                      FIGURE 5.2.                                                                 (4)
5.3       Calculate the following dimensions for a parallel key suitable for a 83 mm
          diameter shaft that must be used in an industrial lathe machine:
          5.3.1       Width                                                                       (2)
          5.3.2       Thickness                                                                   (2)
          5.3.3       Length                                                                      (2)
5.4       Label A and B in FIGURE 5.4 below showing the straddle milling process.

                                        A                     B

                                                FIGURE 5.4                                        (2)
                                                                                                  [18]
Copyright reserved                                                             Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining         11                             DBE/November 2023
                                                    NSC

QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)

6.1       A machinist in a milling workshop is tasked to cut a spur gear with 180 teeth
          and a module of 2,5.

          Calculate the following:

          6.1.1           Pitch-circle diameter                                                           (2)

          6.1.2           Dedendum                                                                        (2)

          6.1.3           Outside diameter                                                                (2)

6.2       FIGURE 6.2 below shows an external dovetail component for a machine vice.

                      y                            136                    y

                  D         E

                                                                                          h = 50
                  60°                                                         60°
                            B
                                      R                        R
                  A          C
                        x    10                     m              10     x
                                                    W

                                                  FIGURE 6.2

          Calculate the following:

          6.2.1           Maximum width (W) distance of the dovetail                                      (6)

          6.2.2           Distance (m) between the precision rollers                                      (6)

6.3       A spur gear with 89 teeth must be cut on a milling machine with the use of a
          dividing head. The dividing head has a ratio of 40 : 1.

          HINT: Use A = 90 divisions for the simple indexing.

          6.3.1           Calculate the indexing that is needed.                                          (3)

          6.3.2           Calculate the change gears that are required.                                   (5)

6.4       Describe any TWO constraints/disadvantages that can be experienced during
          the practical application of balancing a work piece on a lathe when using a
          face plate.                                                                                     (2)
                                                                                                          [28]

Copyright reserved                                                                     Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining    12                      DBE/November 2023
                                               NSC

QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

7.1       What instrument will be used to measure the diameter of the indentation on
          the test material when using a Brinell hardness tester?                             (1)

7.2       State TWO methods to determine the Brinell hardness number.                         (2)

7.3       State ONE of the functions of a moment tester.                                      (1)

7.4       Describe the working principle of a tensile tester.                                 (3)

7.5       What is the difference between a depth micrometer and a screw-thread
          micrometer with regard to the scales on the barrels of the instruments?             (1)

7.6       State THREE ways how to assess the hardness of metals.                              (3)

7.7       Mr Patterson is using a depth micrometer to measure a hole. The
          measurement reading on the micrometer is 5,94 mm and a 50–75 mm
          interchangeable rod is used. What will be the CORRECT depth measurement
          of the hole?                                                                        (2)
                                                                                              [13]

Copyright reserved                                                         Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      13                 DBE/November 2023
                                                 NSC

QUESTION 8: FORCES (SPECIFIC)

8.1       FIGURE 8.1 indicates a system of forces with three pulling forces and one
          pushing force acting onto the same point.

          HINT: Draw and complete the diagram in FIGURE 8.1. Show ALL the
                horizontal and vertical components before you do the calculation.

                                    15 N

                                        75º

                                                                 45 N

                                               60º
                        75 N

                                                 120 N

                                               FIGURE 8.1

          Calculate the following:

          8.1.1       Sum of the horizontal components                                      (4)

          8.1.2       Sum of the vertical components                                        (4)

          8.1.3       Resultant                                                             (2)

          8.1.4       Angle and direction of the resultant                                  (4)

Copyright reserved                                                       Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining       14                   DBE/November 2023
                                                  NSC

8.2       FIGURE 8.2 below shows a uniform beam that is supported by two vertical
          supports, A and B. TWO vertical point loads are exerted onto the beam.
          Calculate the magnitude of the reaction forces in A and B.

          55 N                                                          160 N
                                               8,5 m

                                       7m                            2m

            A                                                 B
                                                FIGURE 8.2                                     (9)

8.3       A mild steel tie bar has a diameter of 20 mm and is 4 m in length. The
          maximum stress in the steel is 640 MPa and Youngʹs modulus of elasticity for
          mild steel is 200 GPa. The safety factor is 3.

          Calculate the following:

          8.3.1       The maximum load the tie bar may carry in kN                             (6)

          8.3.2       The safe working stress in MPa                                           (4)
                                                                                               [33]

Copyright reserved                                                          Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining    15                      DBE/November 2023
                                               NSC

QUESTION 9: MAINTENANCE (SPECIFIC)

9.1       Preventative maintenance can be divided into two subgroups. Name the TWO
          subgroups.                                                                           (2)

9.2       State THREE advantages of belt drives compared to gear drives.                       (3)

9.3       Name THREE types of belt drives.                                                     (3)

9.4       Which material is commonly used for non-stick coatings on frying pans?               (1)

9.5       State TWO uses of EACH of the following composites:

          9.5.1       Polyvinyl chloride (PVC)                                                 (2)

          9.5.2       Bakelite                                                                 (2)

          9.5.3       Fibreglass                                                               (2)

9.6       State whether EACH of the following materials is a thermo-hardened or a
          thermoplastic composite:

          9.6.1       Carbon fibre                                                             (1)

          9.6.2       Nylon                                                                    (1)

          9.6.3       Bakelite                                                                 (1)
                                                                                               [18]

Copyright reserved                                                          Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     16                      DBE/November 2023
                                                NSC

QUESTION 10: JOINING METHODS (SPECIFIC)

10.1      Draw a cross-sectional view of a square screw thread. Label the crest and the
          root of the screw thread.                                                             (3)

10.2      A two-start square screw thread needs to be cut on a lathe. The lead of the
          thread is 25 mm and the crest diameter is 70 mm. The clearance angle must
          be 3°.

          Calculate the following:

          10.2.1      Pitch diameter                                                            (4)

          10.2.2      Helix angle of the screw thread                                           (4)

          10.2.3      Leading tool angle                                                        (2)

          10.2.4      Following tool angle                                                      (2)

10.3      Label parts A–C of the V-screw thread shown in FIGURE 10.3 below.

                                        A        B    C

                                               FIGURE 10.3                                      (3)
                                                                                                [18]

Copyright reserved                                                           Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     17                        DBE/November 2023
                                                NSC

QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)

11.1      FIGURE 11.1 below shows a hydraulic system.

                          f =? N                              F = 350 N

                                      PLUNGER                             RAM

                                   Area plunger = 0,005 m²
                     h             mm

                                                                               25 mm
                                                                                       H

                                               FLUID

                                                FIGURE 11.1

          Calculate the following:

          11.1.1      The area of the ram if the diameter of the cylinder is 110 mm                   (2)

          11.1.2      Force applied on the small piston (plunger)                                     (3)

          11.1.3      The displacement h of the small piston (plunger) in mm                          (3)

11.2      What is the purpose of using pressure gauges in a hydraulic system?                         (2)

11.3      State ONE advantage of applying pneumatics in a system.                                     (1)

Copyright reserved                                                                 Please turn over

### Page 18

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      18                           DBE/November 2023
                                                 NSC

11.4      An electrical motor with a driver pulley of 75 mm diameter rotates at
          25 r/sec. The motor drives a pulley of 350 mm diameter by means of a flat
          belt.

                      DDR = 75 mm
                     NDR = 25 r/sec

                      Motor
                                                              DDN = 350 mm
                                                              NDN = ?

                                               FIGURE 11.4

          Calculate the following:

          11.4.1      The rotational frequency of the driven pulley in r/sec                         (4)

          11.4.2      The belt speed in m.s-1                                                        (2)

11.5      What protects a V-belt against sudden loads so that it cannot get damaged?                 (1)

Copyright reserved                                                                Please turn over

### Page 19

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      19                           DBE/November 2023
                                                 NSC

11.6      FIGURE 11.6 below shows a gear drive system on the shaft of an electric
          motor.

                                                             Output shaft
                                       TB = 55

                     NA = 95 r/min
                     TA = 30

                                                                            TD = 50
                                                                            ND = ?
                                                   TC = 25

                                                   Electric motor
                                               FIGURE 11.6

          Calculate the following:

          11.6.1      The rotation frequency of the output shaft in r/min                          (4)

          11.6.2      The power transmitted if the torque in the system is 120 Nm. Show
                      the CORRECT unit with the final answer.                                      (3)

11.7      A fitter applies a force of 300 N on a ring spanner. What must the length of
          the ring spanner be to generate a torque of 135 Nm?                                      (3)
                                                                                                   [28]

                                                                                      TOTAL:       200

Copyright reserved

### Page 20

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining          1                         DBE/November 2023
                                                     NSC

                     FORMULA SHEET FOR MECHANICAL TECHNOLOGY:
                               FITTING AND MACHINING

1.     BELT DRIVES

1.1    Belt speed = πDN
                         60

1.2    Belt speed = π D  t  N                 (t = belt thickness)
                              60

1.3    Belt mass = Area × Length × Density            (A = thickness × width)

                         Diameter of driven pulley
1.4    Speed ratio =
                         Diameter of driver pulley

1.5    Belt length (flat) = [(D + d) × 1,57] + (2 × centre distance)

                          π D  d  D  d  2
1.6    Open-belt length =                       2c
                              2         4c

                             π D  d  D  d 
                                                            2

1.7    Crossed-belt length =                                    2c
                                 2         4c

1.8    Power (P) =
                         T1  T2  π D N
                                   60
        Where:
              T1 = force in the tight side
              T2 = force in the slack side
              T1 – T2 = effective tensile force (Te)

                                                       T1
1.9    Ratio between tight side and slack side =
                                                       T2

                                 T1
1.10   Width =
                      Permissible tensile force

1.11   NDR × DDR = NDN × DDN

Copyright reserved                                                               Please turn over

### Page 21

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining              2                                  DBE/November 2023
                                                         NSC

2.     STRESS AND STRAIN

       Ashaft = π d
                         2
2.1
                     4

       Apipe = π D  d 
                   2   2
2.2
                             4

                                  Maximum stress/Break stress
2.3    Safety factor =
                                      Safe working stress

                                                                    F
2.4    Stress = Force                                 OR       σ
                     Area                                           A

                     Change in length                               ΔL
2.5    Strain =                                       OR       ε
                      Original length                               oL

                                       Stress                           σ
2.6    Young's modulus =                              OR       E
                                       Strain                           ε

3.     HYDRAULICS

3.1    Pressure = Force                               OR       P
                                                                    F
                             Area                                   A

3.2    Volume = Area × Stroke length (l or s)

3.3    Work done = Force × Distance

3.4    PA = PB

       FA FB
3.5      
       AA AB

4.     GEAR DRIVES

4.1    Power (P) = 2π NT
                                  60

                                 Product of teeth on driven gear                              Ninput
4.2    Gear ratio =                                                     OR   Speed ratio =
                                 Product of teeth on driver gear                              Noutput

Copyright reserved                                                                                 Please turn over

### Page 22

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     3                           DBE/November 2023
                                                NSC

        Ninput    Product of teeth on driven gear
4.3             =
        Noutput   Product of teeth on driver gear

4.4    NA × T A = NB × T B

4.5    Torque = Force × Radius

4.6    Torque transmitted = Gear ratio × Input torque
                     Pitch-circle diameter                           PCD
4.7    Module =                                       OR   m=
                        Number of teeth                               T

                                  Circular pitch × Number of teeth
4.8    Pitch-circle diameter =
                                                  π
                                      OR

                               PCD = CPT
                                      

4.9    Outside diameter (OD) = PCD + 2(m)

4.10   Addendum = Module                       OR          a=m

4.11   Dedendum (b) = 1,157 × m                OR          Dedendum (b) = 1,25 × m

4.12   Cutting depth (h) = 2,157 × m           OR          Cutting depth (h) = 2,25 × m

4.13   Clearance (c) = 0,157 × m               OR          Clearance (c) = 0,25 × m

4.14   Circular pitch (CP) = m × π

4.15   Working depth (WD) = 2 × m              OR          Working depth (WD) = 2 × a

5.     PULLEYS

5.1    NDR × DDR = NDN × DDN

5.2    Power (P) = 2π NT
                          60
                          Diameter of driven pulley
5.3    Velocity ratio =
                          Diameter of driver pulley

Copyright reserved                                                                 Please turn over

### Page 23

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining          4                                 DBE/November 2023
                                                     NSC

6.        KEYWAYS

6.1       Width (W) = D
                        4

6.2       Thickness (T) = D
                             6

6.3       Length (L) = 1,5 × D
          Where:
                 D = Diameter of shaft

6.4       Standard taper for taper key: 1 in 100 or 1 : 100

7.        CINCINNATI DIVIDING HEAD TABLE FOR MILLING MACHINE

                                                  Hole circles
      Side 1       24       25      28      30      34       37      38      39      41       42     43
      Side 2       46       47      49      51      53       54      57      58      59       62     66
                                                 Change gears
      Gears    24 x 2       28      32      40      44       48      56      64      72       86     100

7.1       Indexing = 40          (n = number of divisions)
                        n

               A  n 40
                                                                  A  n 
          Dr                                                 Dr              40
7.2                                     OR
          Dn    A     1                                      Dn              A

          Where:
                A = chosen number of divisions
                n = real number of divisions

8.        DOVETAILS
          Where:
                R = Radius of precision roller
                y = Distance from top edge of dovetail in relation to bottom corner of dovetail
                x = Distance from middle of precision roller to bottom corner of dovetail
                θ = Dovetail included angle (normally 60°)
                h = Height of dovetail
                w = Minimum width of dovetail
                W = Maximum width of dovetail
                m = Distance between rollers
                M = Distance over rollers

Copyright reserved                                                                            Please turn over

### Page 24

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     5                            DBE/November 2023
                                                NSC

9.     TAPERS

              θ D-d
9.1     tan    =          (l = Taper length)
              2 2l

                             LD - d 
9.2    Tailstock setover =               (L = Distance between centres)
                               2l

10.    SCREW THREADS

                                                                                      P
10.1   Mean diameter = Outside diameter – (½ × Pitch)           OR        Dm  OD 
                                                                                      2
10.2   Effective diameter (Deff) = Pitch diameter (Dp) = Mean diameter (Dm)

10.3   Lead = Pitch × Number of starts

10.4   Height of screw thread = 0,866 × Pitch (P)

10.5   Depth of screw thread = 0,613 × Pitch (P)

                                Lead
10.6   Helix angle: Tan θ =
                               π  Dm

10.7   Leading angle = 90° ‒ (Helix angle + Clearance angle)

10.8   Following angle = 90° + (Helix angle ‒ Clearance angle)

10.9   DP = DN – (0,866 × P)

Copyright reserved                                                                 Please turn over

### Page 25

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining    6    DBE/November 2023
                                               NSC

11.    PYTHAGORAS' THEOREM AND TRIGONOMETRY

                               r
          y

                           x
                  y
11.1    Sin θ 
                  r

                  x
11.2    Cos θ 
                  r

                      y
11.3   Tan θ 
                      x

11.4    r 2  x2  y2

Copyright reserved

## Related documents

- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-afr/cad6695c-dbf0-406d-a72d-78edaf6ce649) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — Mechanical Technology · QP · 2023 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng
- [Mechanical Technology May-June 2024 (Fitting and Machining) MG Afr](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-memorandum-afrikaans/03c703c8-8125-4d5a-a124-37013b381c7a) — Memo · 2024 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
