# Mechanical Technology Grade 12 NSC November 2023 Memo (Eng)

> Grade 12 Mechanical Technology memorandum from the NSC November Exam 2023 (English), 27 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-mg-eng/55150b9e-0ef8-4865-b2c0-9c09a3209a0e
- Updated: 2026-10-29
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2023
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 27

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC November 2023 Memo (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-mg-eng/55150b9e-0ef8-4865-b2c0-9c09a3209a0e)

## About this document

Mechanical Technology · Grade 12 · NSC November Exam · 2023. Memorandum. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                  NATIONAL
                             SENIOR CERTIFICATE

                                    GRADE 12

           MECHANICAL TECHNOLOGY: FITTING AND MACHINING

                                  NOVEMBER 2023

                              MARKING GUIDELINES

MARKS: 200

                     These marking guidelines consist of 27 pages.

Copyright reserved                                                   Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining 2                  DBE/November 2023
                                      NSC – Marking Guideline

QUESTION 1: MULTIPLE-CHOICE (GENERIC)

1.1       B                                                                      (1)

1.2       A                                                                      (1)

1.3       C                                                                      (1)

1.4       C                                                                      (1)

1.5       A                                                                      (1)

1.6       B                                                                      (1)
                                                                                  [6]

Copyright reserved                                                 Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      3                 DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 2: SAFETY (GENERIC)

2.1       Examination checks:
           Severe bleeding 
           Internal bleeding 
           Head injuries 
           Neck injuries 
           Fractures 
           Vital signs 
           Physical abnormalities 
                                                                        (Any 2 x 1)     (2)

2.2       Safety devices on the power-driven guillotine:
           Finger protectors / Fixed guards / Blade guard 
           Rear view mirrors 
           Rear light curtains 
           Automatic sweep-away 
           Revolving warning lights 
           Two-hand / dual control device 
           Additional emergency buttons 
           Self-adjusting guards 
           Covered footswitch 
                                                                        (Any 2 x 1)     (2)

2.3       Grinding wheel:
           The wheel should be rated above the speed of the motor. 
           Check for cracks on the grinding wheel. 
           Check for chips on the grinding wheel. 
           Check that the arbor hole is the correct size. 
           Must not be contaminated by oil/fluids or grease. 
           Correct size of the wheel. 
           Correct type of wheel for the material. 
                                                                        (Any 2 x 1)     (2)

2.4       Gas welding equipment – safety devices:
           Valve guard 
           Flash back arrestor 
           Pressure regulator 
           C-clamps on hoses/Parallel hose clips 
           Acetylene spindle key must always be in place. 
           Cylinder valves. 
                                                                        (Any 2 x 1)     (2)

Copyright reserved                                                         Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      4              DBE/November 2023
                                       NSC – Marking Guideline

2.5       Advantages of process layout of machines are:
           High machine utilisation. 
           Better supervision. 
           Less interruption in the flow of work. 
           Lower equipment costs. 
           Better control of total manufacturing costs. 
           Greater flexibility. 
                                                                 (Any 2 x 1)      (2)
                                                                                  [10]

Copyright reserved                                                   Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      5                      DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 3: MATERIALS (GENERIC)

3.1      Colour code of metal:
          To identify the type of metal. 
          To identify carbon content especially after the metal was stored. 
          To identify the profile/size of the metal. 
                                                                         (Any 1 x 1)       (1)

3.2       Tests to determine properties of steel:

          3.2.1      Sound test:
                      Hardness 
                      Softness 
                                                                          (Any 1 x 1)      (1)

          3.2.2      Bending test:
                      Ductility 
                      Bend strength 
                      Fracture strength 
                      Resistance to fracture
                      Brittleness 
                      Elasticity 
                      Plasticity 
                      Flexibility 
                                                                          (Any 1 x 1)      (1)

          3.2.3      Machining test:
                      Hardness 
                      Strength 
                                                                          (Any 1 x 1)      (1)

3.3      Reasons metal soaked during heat treatment:
          To ensure uniform heat distribution  throughout the metal. 
          To achieve a uniform grain structure  after cooling the metal. 
                                                                        (Any 1 x 2)        (2)

3.4      Case hardening:
          Carburising 
          Nitriding 
          Cyaniding 
                                                                          (Any 2 x 1)      (2)

3.5       Annealing process:
          Heating the steel slightly above AC3, (upper critical temperature)  soaking
          it for a required time/period  and then slow cooling  back to room
          temperature.                                                                     (3)

Copyright reserved                                                            Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      6              DBE/November 2023
                                       NSC – Marking Guideline

3.6      Rapid quenching mediums:
          Brine/Salt water 
          Water 
          Nitrogen 
          Oil 
                                                                  (Any 2 x 1)     (2)

3.7       Heat treatment process:
          Tempering                                                              (1)
                                                                                  [14]

Copyright reserved                                                   Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      7              DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 4: MULTIPLE-CHOICE (SPECIFIC)

4.1       D                                                                      (1)

4.2       A                                                                      (1)

4.3       A                                                                      (1)

4.4       C                                                                      (1)

4.5       D                                                                      (1)

4.6       B                                                                      (1)

4.7       B                                                                      (1)

4.8       A                                                                      (1)

4.9       C                                                                      (1)

4.10      D                                                                      (1)

4.11      B                                                                      (1)

4.12      A                                                                      (1)

4.13      C                                                                      (1)

4.14      D                                                                      (1)
                                                                                  [14]

Copyright reserved                                                   Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      8                  DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)

5.1       Disadvantages of compound slide method
              Only short tapers can be cut. 
              It causes fatigue to the operator. 
              The automatic feed of the machine cannot be used. 
                                                                      (Any 2 x 1)     (2)

5.2       Taper calculations:

          5.2.1      Length of taper:

                                   D-d
                      Tan       
                            2       2 l

                                    D-d
                        2 l 
                                           
                                    tan
                                          2

                                    78 - 55
                          2l               
                                    tan4°

                                         23
                          2l 
                                    0,069926811

                                    328,9153283
                            l                  
                                         2

                            l  164,46 mm 
                                                                                      (4)

          5.2.2      Tailstock set-over:

                                          L D - d 
                     Set - over 
                                              2l
                                                  
                                       284,46  78 - 55 
                                     
                                         2  164,46 

                                     = 19,89 mm                                      (4)

Copyright reserved                                                       Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining      9              DBE/November 2023
                                       NSC – Marking Guideline

5.3       Key ways:

          5.3.1      Width:
                                D
                      Width =
                                4

                                83
                      Width =      
                                 4

                            = 20,75 mm                                           (2)

          5.3.2      Thickness:
                                      D
                     Thickness 
                                      6

                                      83 
                     Thickness 
                                       6

                                     13,83 mm                                   (2)

          5.3.3      Length:
                     Length  1,5  diameter of shaft
                             1,5  83 
                             124,50 mm                                          (2)

5.4       Straddle milling:
              A. Side and face cutter / Milling cutters. 
              B. Arbor / Spacers / Spindle / Axle                                 (2)
                                                                                   [18]

Copyright reserved                                                   Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     10                            DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)

6.1       Gear terminology:

          6.1.1      Pitch-circle diameter:
                     PCD  m  T                         CP  m  
                            2,5  180                      2,5  
                            450 mm                         7,85 mm 
                                                              CP  T
                                                 OR     PCD 
                                                                      
                                                                   7,85 180
                                                                 
                                                                        
                                                                  450mm                       (2)

          6.1.2      Dedendum:

                      Dedendum  1,157  m                        Dedendum  1,25  m
                                1,157  2,5            OR                 1,25  2,5 
                                2,89 mm                                   3,13 mm 
                                                                                                (2)

          6.1.3      Outside diameter:

                     OD  PCD  2m
                         450  22,5  
                         455 mm                                                               (2)

Copyright reserved                                                                 Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     11                      DBE/November 2023
                                       NSC – Marking Guideline

6.2       Dovetails:

          W = 136 + 2(DE)
          m = W – [2(AC) + 2(R)] OR m = W – 2(AC + R) OR m = W – 2(AC) – 2(R)

          6.2.1      Maximum width distance of dove tail: (W)

                     Calculate DE or y:

                                                                   AD
                                                             tanθ =
                              DE                                   DE
                       tan 
                              AD                                   50
                                                          tan60° =
                       DE  tan  AD           OR                DE
                           tan30°  50                     DE =
                                                                     50
                           28,87 mm                              tan60°
                                                                 = 28,87mm

                       W  136  2(DE) 
                          136  2(28,87) 
                          136  57,74
                          193,74 mm                                                     (6)

Copyright reserved                                                           Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     12                        DBE/November 2023
                                       NSC – Marking Guideline

          6.2.2      Distance between the rollers: (m)

                     Calculate AC or x:

                                BC
                     Tan =
                                AC                                    AC
                                                             Tan =
                                                                      BC
                                 BC
                        AC =                                    AC =Tan  BC 
                                Tan
                                                   OR
                                  10                               =Tan60o  10 
                            =          
                                Tan30o
                                                                   =17,32mm 
                            =17,32mm 

                     m = W – [(2(AC) + 2(R)] 
                        = 193,74 – [2(17,32) + 2(10)] 
                        = 193,74 – (34,64 + 20)
                        = 139,10 mm 
                                 OR
                     m = W – 2(AC + R) 
                        = 193,74 – 2(17,32 + 10) 
                        = 193,74 – (34,64 + 20)
                        = 139,10 mm 
                                OR
                     m = W – 2(AC) – 2(R) 
                        = 193,74 – 2(17,32) – 2(10) 
                        = 193,74 – 34,64 – 20
                        = 139,10 mm 
                                                                                             (6)

Copyright reserved                                                              Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     13                              DBE/November 2023
                                       NSC – Marking Guideline

6.3      Milling of spur gear:
         6.3.1     Indexing:

                                    40 40
                     Indexing        
                                    N   89
                                    40 40
                                         
                                    A   90
                                    4 6
                                    
                                    9 6
                                    24
                                      
                                    54
                                                                                         
                                 Indexing : 0 full turns and 24 holes on a 54  hole circle      (3)

          6.3.2      Change gears:

                     Dr              40
                          A  n 
                     Dn              A
                                                          Driver   A -N   40
                                                                       
                     Dr                 40                Driven    A      1
                          90  89      
                     Dn                 90
                                                                       90 - 89   40 
                                                                              
                                                                        90        1
                                40
                         1
                                90
                                                                        1   40
                                                                         
                                                                       90    1
                            40                    OR
                        
                            90 
                                                                       40
                                                                         
                                                                       90
                            4
                        
                            9
                                                                       4   8
                                                                           
                                                                       9   8
                            4 8
                             
                            9 8
                                                                 Dr 32 
                                                                   
                                                                 Dn 72 
                     Dr 32 
                       
                     Dn 72 
                                                                                                  (5)

Copyright reserved                                                                   Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     14                   DBE/November 2023
                                       NSC – Marking Guideline

6.4       Balancing constraints/disadvantages:
              Requires specialised machinery. 
              Difficult to ascertain the exact point of unbalance. 
              Requires accurate removal or adding of material (weight) to the
               object. 
              Can lead to interference with parts of the machine when weights are
               added to parts. 
                                                                       (Any 2 x 1)     (2)
                                                                                       [28]

Copyright reserved                                                        Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     15                        DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

7.1       Instrument to measure indentation:
          Microscope                                                                        (1)

7.2       Brinell hardness number:
              Calculations 
              The use of a Brinell hardness table                                          (2)

7.3       Function of moment tester:
          To determine the reactions on either side of a simply loaded beam.                (1)

7.4       Principal of tensile tester:
          The tensile tester is a destructive  tester that subjects a piece of material
          to an increasing axial load  while measuring the corresponding elongation
          of the material.                                                                  (3)

7.5       Depth and screw-thread micrometer:
          The scale on the depth micrometer’s barrel reads in the opposite direction
          compared to the screw thread micrometer.                                          (1)

7.6       Hardness assessment:
              Resistance to penetration / Hardness tests 
              Sound test 
              Elastic hardness / Bending test / Tensile test 
              Resistance to abrasion / File test / Spark test / Machining test 
                                                                          (Any 3 x 1)        (3)

7.7       Micrometer measurement:
                       
          5,94 + 50 = 55,94 mm                                                               (2)
                                                                                             [13]

Copyright reserved                                                              Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     16                       DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 8: FORCES (SPECIFIC)

8.1       Forces:

          8.1.1      Horizontal component:

                       HC  45cos0  75cos30  15cos75 120cos270
                                          
                       HC  45  64,95  3,88  0

                       HC  106,07 N                                                     (4)

          8.1.2      Vertical component:

                       VC  45sin0  75sin30  15sin75  120sin270

                                               
                       VC  0  37,5  14,49  120

                       VC   68,01 N                                                    (4)
                                                       OR
      Force   θ  8.1.1  ∑HC/x = Fcosθ                      8.1.2    ∑VC/y = Fsinθ
       45N    0º HC = 45cos0°     45N                     VC = 45sin0°     0N
       75N   30º HC = 75cos30°    64,95N                  VC = 75sin30°    37,5N 
       15N  105º HC = 15cos105°   -3,88N                  VC = 15sin105°   14,49N 
      120N 270º HC = 120cos270° 0N                         VC = 120sin270° -120N 
                            Total 106,07N                                  -68,01N       (8)

          8.1.3      Resultant:

                     R 2  VC2  HC2

                              68,01  106,07  
                                      2            2
                       R
                       R  15876,21
                       R  126,00 N                                                       (2)

Copyright reserved                                                            Please turn over

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     17               DBE/November 2023
                                       NSC – Marking Guideline

          8.1.4      Angle and direction of resultant:
                     Angle:
                                   VC
                            tanθ 
                                   HC
                                          68,01                       θE
                               θ  tan1         
                                          106,07  
                                  θ  tan1  0,64                            R
                                                                      S
                                  θ  32,67 

                     Direction:
                     R =126,00N 32,67° / 32°40' South of East 

                                                       OR

                     Angle:
                                       HC
                              tan =
                                       VC                                  E
                                             106,07                θ
                                   = tan-1                                  R
                                             -68,01  
                                                                  S
                                   = tan-1 1,559623585 
                                   = 57,20° 

                     Direction:
                     R =126,00N 57,33° / 57°20' East of South                         (4)

Copyright reserved                                                        Please turn over

### Page 18

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     18              DBE/November 2023
                                       NSC – Marking Guideline

8.2       Reaction in supports A and B:

          Reaction in support A:
          Take moments about B:

           LHM   RHM
                                
           55  7    
                     A  7  160  1,5 

              385  7A  240

                      145
                 A       
                       7

                 A  20,71 N 

          Reaction in support B:
          Take moments about A:

           LHM   RHM
                                      
           B  7    55  0   160  8,5 
               7B  0  1360

                      1360
                 B        
                        7

                 B  194,29 N                                                     (9)

Copyright reserved                                                   Please turn over

### Page 19

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     19                            DBE/November 2023
                                       NSC – Marking Guideline

8.3       Stress and strain:

          8.3.1      Maximum load:

                            π D2
                      A
                              4
                            π 0,022
                                   
                               4
                         3,14159265  10 -4 m2  OR       3,14  10 -4 m2 

                            F
                      σ
                            A

                     F  Aσ 

                                               
                      F = 3,14159265×10-4  640  106
                      F = 201061,93 N
                      F = 201,06 kN  OR 200,96kN                                              (6)

          8.3.2      Safe working stress:
                          MS
                     SF 
                          SS
                          MS
                     SS       
                          SF
                          640  106 
                     SS 
                             3 
                     SS  213333333,3 Pa
                     SS  213,33 MPa                                                           (4)
                                                                                                 [33]

Copyright reserved                                                                 Please turn over

### Page 20

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     20                  DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 9: MAINTENANCE (SPECIFIC)

9.1       Preventative maintenance:
          Subgroups of preventative maintenance:
              Planned or scheduled maintenance 
              Conditional-based maintenance                                          (2)

9.2       Advantages of belt drives over gear drives:
             Produce less noise than gear drives. 
             Produce less vibration than gear drives. 
             More cost effective.
             Belt drives will slip under a sudden load /over load to protect the
               drive. 
             Do not need lubrication like gear drives.
             Belt drives do not require parallel shafts. 
             Belts can be used over long distances. 
                                                                      (Any 3 x 1)      (3)

9.3       Belt drives:
              V-pulley 
              Wedge pulley 
              Flat pulley 
              Round belt 
              Timing/Toothed belt 
              Multi-groove belt 
                                                                      (Any 3 x 1)      (3)

9.4       Non-stick material:
          Teflon                                                                      (1)

9.5       Uses:
          Polyvinyl chloride (PVC):
          9.5.1        Trays for food and toiletries 
                       Clear bottles 
                       Blister packaging 
                       Drain and sewerage pipes 
                       Electrical pipes 
                       Drip bags 
                       Cooking bottles 
                       Vinegar bottles 
                       Credit cards 
                       Shoe soles 
                       Floor tiles 
                       Wallpaper 
                       Outdoor furniture 
                       Disposable cutlery 
                                                                      (Any 2 x 1)      (2)

Copyright reserved                                                        Please turn over

### Page 21

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     21              DBE/November 2023
                                       NSC – Marking Guideline

          9.5.2      Bakelite:
                        Electrical insulators 
                        Kitchenware 
                        Jewellery 
                        Toys 
                        Distributor rotors 
                        Disc brake cylinders 
                        Sauce pan handles 
                        Electrical switches 
                        Electrical parts 
                        Aircraft components 
                        Bearings 
                        Clutch linings 
                        Brake linings 
                        Laminated materials 
                        Computer motherboards 
                                                                  (Any 2 x 1)     (2)

          9.5.3      Fibre Glass
                         Surface covering 
                         Woven cloth 
                         Pillow stuffing 
                         Reinforced plastics 
                         Boats 
                         Motor vehicle bodies 
                         Roof sheeting 
                         Petrol tanks 
                         Swimming pools 
                         Furniture 
                         Fruit and salad bowls 
                         Ornaments 
                         Sporting equipment 
                         Jigs forms 
                                                                  (Any 2 x 1)     (2)

9.6       Thermo-hardened or thermoplastic:

          9.6.1      Carbon fibre:
                     Thermo-hardened / Thermosetting                             (1)

          9.6.2      Nylon:
                     Thermoplastic                                               (1)

          9.6.3      Bakelite:
                     Thermo-hardened / Thermosetting                             (1)
                                                                                   [18]

Copyright reserved                                                   Please turn over

### Page 22

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     22                          DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 10: JOINING METHODS (SPECIFIC)

10. 1     Square screw thread:

                                          Crest          Root 

                                                                    (For the sketch)

                                                                                               (3)

10.2      Square Thread:

          10.2.1     Pitch diameter:

                                    Lead
                     Pitch 
                              Number of starts
                              25
                                 
                               2
                             12,50 mm 

                                   P
                       PD  OD -
                                   2
                                  12,50
                            70 -       
                                    2
                        PD  63,75 mm                                                         (4)

          10.2.2     Helix angle of the thread:

                                Lead
                      Tan 
                                 Dp
                                  25 
                      Tan 
                                 63,75 
                            tan-1  0,124827406  
                             = 7,12 OR 7 7'                                                 (4)

          10.2.3     Leading angle:

                     Leading angle                (Helix angle + Clearance angle)
                                                  (7,12° + 3°) 
                                          = 79,88° OR 7 53’ 
                                                                                               (2)

Copyright reserved                                                                Please turn over

### Page 23

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     23                        DBE/November 2023
                                       NSC – Marking Guideline

          10.2.4     Following angle:

                     Following angle       = 90° + (Helix angle – Clearance angle)
                                           = 90° + (7,12    3°) 
                                           = 94,12° OR 94°7’                                (2)

10.3      ISO V-screw thread:
             A. Helix angle 
             B. Pitch / Lead 
             C. Root                                                                        (3)
                                                                                             [18]

Copyright reserved                                                              Please turn over

### Page 24

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     24                        DBE/November 2023
                                       NSC – Marking Guideline

QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)

11.1      Hydraulic systems :

          11.1.1     Area of Ram:

                                    D2
                      A Ram  
                                     4

                                    (0,110) 2
                             A                  
                                         4

                              A  0,0095 m 2  OR       9,50×10 -3 m 2                     (2)

          11.1.2     Applied force on plunger:
                        F
                     p
                        A

                      f F
                         
                      a A

                           Fa
                      f
                            A

                           350  0,005
                      f               
                             0,0095

                      f  184,21 N                                                         (3)

Copyright reserved                                                             Please turn over

### Page 25

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     25                 DBE/November 2023
                                       NSC – Marking Guideline

          11.1.3     Displacement h:

                      VPlunger = VRam

                       a × h  A ×H

                                A ×H 
                           h
                                  a

                                0,0095  0,025
                           h                  
                                    0,005

                           h  0,0475 m

                           h  47,5 mm                                              (3)

11.2      Pressure gauge:
              To adjust pressure control valves. 
              Determining the pressure being exerted. 
              For safety. 
              Indicates if leakages are present in the system. 
                                                                     (Any 2 x 1)     (2)

11.3      Advantages of pneumatics:
             Pneumatic tools are very environmentally friendly. / Clean
               operation 
             Last longer. 
             More robust. 
             More compact. 
             Easily maintained. 
             Easily installed.
             Cost effective. 
             Safe to use. 
             High power-to-weight ratio. 
             Simple control. 
             Quick response. 
             Versatile. 
                                                               (Any 1 x 1)           (1)

Copyright reserved                                                      Please turn over

### Page 26

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining     26                           DBE/November 2023
                                       NSC – Marking Guideline

11.4      Belt drive:

          11.4.1        The rotational frequency in r/sec:

                     N DR  D DR  N DN  D DN

                              N DR  D DR
                     N DN                  
                                 D DN

                              25  75 
                     N DN 
                               350 

                     N DN  5,36 r / sec                                                        (4)

          11.4.2     Belt speed:

          Belt Speed  V   π DDR  NDR               Belt Speed  V   π DDR  NDR
                            π  0,075  25  OR                        π  0,350  5,36 
                            5,89 m / s                                5,89 m / s             (2)

11.5      V-Belt:
          The slippage of the v-belt.                                                           (1)

11.6      Gear drives:
          11.6.1    The rotational frequency:
                    N input   Product of teeth on driven gears
                            
                    N output Product of teeth on driver gears
                         NA       TB  TD
                              
                         ND       TA  TC
                         95   55  50 
                            
                         ND   30  25 
                                  30  25  95
                          ND                  
                                    55  50
                                71250
                          ND 
                                 2750
                          N D  25,91 r / min 
                                                                                                 (4)

Copyright reserved                                                                  Please turn over

### Page 27

Downloaded from hlayiso.com
Mechanical Technology: Fitting and Machining 27                 DBE/November 2023
                                      NSC – Marking Guideline

          11.6.2     Power transmitted:
                                  2 N T
                     Power P  
                                    60

                                      2 ×  × 95 ×120 
                                 P
                                             60

                                 P  1193,81  Watt(W ) 
                                   OR
                                 P  1,19  Kilowatt(kW )                      (3)

11.7      Length of spanner:

           Torque(T ) 
                      Force      Radius
                                  

                           T
                Radius      
                           F

                           135
                Radius        
                           300

                Radius  0,45 m 
                       OR
                Radius  450 mm                                                (3)
                                                                                [28]

                                                                    TOTAL:      200

Copyright reserved

## Related documents

- [Mechanical Technology Nov 2023 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-fitting-and-machining-afr/ec5f897b-937f-4bae-aad9-e566a280b360) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-afr/b8922567-d93f-4dcd-9279-3b4c4bd034b9) — Mechanical Technology · QP · 2023 · Afr
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-eng/b9535038-8936-48a1-afcd-0ab67f8f03aa) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2023-automotive-eng/5f5706ce-d5c1-4862-ad58-e58260ec3dad) — Mechanical Technology · QP · 2023 · Eng
- [Mechanical Technology Nov 2023 (Welding & Metal Work) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2023-welding-metal-work-afr/cad6695c-dbf0-406d-a72d-78edaf6ce649) — Mechanical Technology · QP · 2023 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-afrikaans/f45c553c-63a1-4e1c-b9c6-d426a3dfef26) — Mechanical Technology · Memo · 2023 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — QP · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
