# Mechanical Technology Grade 12 November 2024 NSC QP (Eng)

> Grade 12 Mechanical Technology question paper from the November 2024 NSC (English), 19 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 19

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 November 2024 NSC QP (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1)

## About this document

Mechanical Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 19 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Confidential

                                NATIONAL
                           SENIOR CERTIFICATE

                                   GRADE 12

                     MECHANICAL TECHNOLOGY: AUTOMOTIVE

                                NOVEMBER 2024

MARKS: 200

TIME: 3 hours

        This question paper consists of 17 pages and a 2-page formula sheet.

Copyright reserved                                                   Please turn over

### Page 2

Mechanical Technology: Automotive             2                             DBE/November 2024
                                        NSC Confidential

 INSTRUCTIONS AND INFORMATION

 1.         Write your centre number and examination number in the spaces provided
            on the ANSWER BOOK.

 2.         Read ALL the questions carefully.

 3.         Answer ALL the questions.

 4.         Number the answers correctly according to the numbering system used in
            this question paper.

 5.         Start EACH question on a NEW page.

 6.         Show ALL calculations and units. Round off final answers to TWO decimal
            places.

 7.         Candidates may use non-programmable scientific calculators and drawing
            instruments.

 8.         The value of gravitational acceleration should be taken as 9,81 m/s2 or
            10 m/s2.

 9.         All dimensions are in millimetres, unless stated otherwise in the question.

 10.        Write neatly and legibly.

 11.        A formula sheet is attached at the end of the question paper.

 12.        Use the criteria below to assist you in managing your time.

 QUESTION                         CONTENT                          MARKS       TIME IN MINUTES
                                   GENERIC
       1         Multiple-choice Questions                            6                    6
       2         Safety                                               10                  10
       3         Materials                                            14                  14
                                  SPECIFIC
       4         Multiple-choice Questions                            14                  10
       5         Tools and Equipment                                  23                  20
       6         Engines                                              28                  25
       7         Forces                                               32                  25
       8         Maintenance                                          23                  20
       9         Systems and Control (Automatic Gearbox)              18                  20
                 Systems and Control (Axles, Steering
       10                                                             32                  30
                 Geometry and Electronics)
                                                      TOTAL           200              180

Copyright reserved                                                             Please turn over

### Page 3

Mechanical Technology: Automotive              3                              DBE/November 2024
                                         NSC Confidential

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

 Various options are provided as possible answers to the following questions. Choose
 the answer and write only the letter (A–D) next to the question numbers
 (1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E.       Nov

 1.1       Which statement below is CORRECT in terms of a recommendation for the
           application of first aid?

           Do NOT …

           A     remove anything that is stuck to the wound.
           B     check the pulse of the patient.
           C     give attention to the loss of blood or breathing difficulties.
           D     check the surroundings for dangerous objects.                                       (1)

 1.2       Where more than … employees are employed at a workplace, the employer
           must provide an accessible first-aid box.

           A     2
           B     3
           C     4
           D     5                                                                                   (1)

 1.3       What causes accidents when working with revolving machinery, such as
           a bench grinder?

           A     Overconfidence
           B     Correct wheel size
           C     Gap between tool rest and grinding wheel not exceeding 3 mm
           D     Correctly rated grinding wheel for the bench grinder                                (1)

 1.4       Which test does NOT damage a work piece?

           A     Spark test
           B     Sound test
           C     Bending test
           D     Machining test                                                                      (1)

 1.5       Which of the following products is case-hardened?

           A     Tin cans
           B     Machine guards
           C     Hand files
           D     Gears and cams                                                                      (1)

 1.6       Which process is the first step in the production of high-strength steel?

           A     Normalising
           B     Annealing
           C     Hardening
           D     Tempering                                                                           (1)
                                                                                                     [6]
Copyright reserved                                                                Please turn over

### Page 4

Mechanical Technology: Automotive              4                              DBE/November 2024
                                         NSC Confidential

 QUESTION 2: SAFETY (GENERIC)

 2.1       State TWO safety precautions that must be adhered to after the horizontal
           band saw has been switched on.                                                             (2)

 2.2       Name the THREE stages when basic first-aid treatment is given to help an
           injured person.                                                                            (3)

 2.3       Why must oil or grease NOT be in contact with the oxygen fittings when
           handling oxygen cylinders?                                                                 (1)

 2.4       State TWO disadvantages of the process workshop layout.                                    (2)

 2.5       State TWO advantages of the product workshop layout.                                       (2)
                                                                                                      [10]

 QUESTION 3: MATERIALS (GENERIC)

 3.1       State if the following materials are easy or hard to file during a filing test:

           3.1.1      Cast iron                                                                       (1)

           3.1.2      Cast steel                                                                      (1)

           3.1.3      Mild steel                                                                      (1)

 3.2       Explain what heat treatment is.                                                            (3)

 3.3       Explain what the effects will be if metal is heated too fast during the heat-
           treatment process.                                                                         (4)

 3.4       Name the TWO types of steel best suited for case hardening.                                (2)

 3.5       Explain the reason for tempering steel during the heat-treatment process.                  (2)
                                                                                                      [14]

Copyright reserved                                                                 Please turn over

### Page 5

Mechanical Technology: Automotive              5                         DBE/November 2024
                                         NSC Confidential

 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

 Various options are provided as possible answers to the following questions. Choose
 the answer and write only the letter (A–D) next to the question numbers
 (4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 E.

 4.1       An OBD scanner is used on vehicles with …

           A     carburettors.
           B     no electronic control module (ECM).
           C     an electronic control unit (ECU).
           D     contact breaker ignition systems.                                                (1)

 4.2       Which wheel alignment tool is used to measure toe-out?

           A     Turntable
           B     Dunlop gauge
           C     Bubble gauge
           D     Wheel balancer                                                                   (1)

 4.3       Which ONE of the following is part of the reciprocating mass in an engine?

           A     Camshaft
           B     Valves
           C     Pistons
           D     Crankshaft                                                                       (1)

 4.4       Which ONE of the following is the cause of crankshaft vibrations?

           A     Carefully balanced crank webs
           B     Oval crankshaft journals
           C     Balanced rotating mass
           D     Balanced reciprocating mass                                                      (1)

 4.5       Torque is defined as …

           A     the rotational frequency of a shaft.
           B     a force causing linear movement.
           C     the rate at which work is done.
           D     the twisting force applied to a rotating shaft.                                  (1)

 4.6       Which method below is used to increase the compression ratio of an engine?

           A     Fit a thinner gasket between the cylinder block and the cylinder head
           B     Fit the pistons with suitable lower crowns
           C     Fit a thicker gasket between the cylinder block and the cylinder head
           D     Fit a crankshaft with a shorter stroke                                       (1)

Copyright reserved                                                             Please turn over

### Page 6

Mechanical Technology: Automotive             6                        DBE/November 2024
                                        NSC Confidential

 4.7       Identify the diagram shown in FIGURE 4.7 below.

                                            FIGURE 4.7

           A     Planimeter
           B     Indicator diagram
           C     Carbon content equilibrium diagram
           D     Stress-strain diagram                                                        (1)

 4.8       Which ONE of the following is a reason for a high hydrocarbon (HC) reading
           on an internal combustion engine?

           A     Ideal air-fuel ratio
           B     Warm valves
           C     A clogged air filter
           D     Lean air-fuel ratio                                                          (1)

 4.9       A wet compression test can be used to determine whether the cylinder has
           a leak at the …

           A     intake valve.
           B     exhaust valve.
           C     piston rings.
           D     head gasket.                                                                 (1)

 4.10      Which of the following determines the correct gear ratio according to load
           and speed in an automatic gearbox?

           A     Brake bands
           B     Hydraulic pistons
           C     Valve body
           D     Oil pump                                                                     (1)

Copyright reserved                                                         Please turn over

### Page 7

Mechanical Technology: Automotive             7                           DBE/November 2024
                                        NSC Confidential

 4.11      Which gear is selected when the planet carrier is locked on an epicyclic gear
           system?

           A     First or low gear
           B     Second or intermediate gear
           C     Third or top gear
           D     Reverse gear                                                                    (1)

 4.12      Which of the following will cause a large positive camber angle on the wheels
           of a vehicle?

           A     Increase the negative effects of KPI
           B     A negative cornering effect of the vehicle
           C     The wheels will stop rotating
           D     The tyres will wear evenly                                                      (1)

 4.13      Identify the symbol shown in FIGURE 4.13 below.

                                           FIGURE 4.13

           A     Regulator
           B     Capacitor
           C     Diode
           D     Distributor                                                                     (1)

 4.14      What is the function of a diesel particulate filter (DPF)?

           A     To clean the intake air
           B     To clean the particles from the fuel
           C     To atomise the fuel
           D     To convert soot into ash                                                        (1)
                                                                                                 [14]

Copyright reserved                                                            Please turn over

### Page 8

Mechanical Technology: Automotive             8                         DBE/November 2024
                                        NSC Confidential

 QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)

 5.1       Why are the following procedures performed during a compression test?

           5.1.1      The air filter is removed                                               (1)

           5.1.2      Dirt is removed from around the spark plugs before removing the
                      spark plugs                                                             (1)

           5.1.3      Disconnect the ignition system                                          (1)

           5.1.4      Record the readings                                                     (1)

 5.2       FIGURE 5.2 below shows a cylinder leakage tester. Answer the questions
           that follow.

                     Pressure
                     gauge
                                                              C

                     A

                                                             B

                                            FIGURE 5.2

           5.2.1      Label A–C.                                                              (3)

           5.2.2      What is the unit of measurement on the pressure gauge?                  (1)

           5.2.3      What is the unit of measurement of gauge C?                             (1)

 5.3       State FOUR safety precautions that must be observed when performing the
           exhaust gas analysis.                                                              (4)

 5.4       Describe TWO functions of the on-board diagnostic scanner.                         (2)

Copyright reserved                                                         Please turn over

### Page 9

Mechanical Technology: Automotive           9                          DBE/November 2024
                                      NSC Confidential

 5.5       FIGURE 5.5 below shows a machine used in an automotive workshop.
           Answer the questions that follow.

                                          FIGURE 5.5

           5.5.1      Identify the machine.                                                    (1)

           5.5.2      State TWO functions of this machine.                                     (2)

           5.5.3      What safety device is NOT attached to this machine?                      (1)

           5.5.4      Why should this machine be calibrated?                                   (1)

 5.6       Explain, in THREE steps, how to measure the camber angle after the bubble
           gauge is fitted to the wheel.                                                       (3)
                                                                                               [23]

Copyright reserved                                                          Please turn over

### Page 10

Mechanical Technology: Automotive            10                            DBE/November 2024
                                       NSC Confidential

 QUESTION 6: ENGINES (SPECIFIC)

 6.1       What is the primary function of the crankshaft?                                         (2)

 6.2       Name the part that is usually attached to the nose of the crankshaft to
           decrease vibrations.                                                                    (1)

 6.3       Why is the reciprocating mass kept as light as possible?                                (1)

 6.4       Explain how to obtain the firing order from the valve train of an engine, after
           the tappet cover has been removed.                                                      (3)

 6.5       FIGURE 6.5 below shows the configuration of a four-stroke four-cylinder
           engine. Answer the questions that follow.

                                                                           B

                           A

                                                C

                                            FIGURE 6.5

           6.5.1      Identify the type of engine configuration.                                   (1)

           6.5.2      Label A–C.                                                                   (3)

 6.6       Draw a neat, labelled sketch to illustrate the position of the crank pins in
           a six-cylinder in-line engine.                                                          (3)

 6.7       Answer the following questions with regard to turbochargers:

           6.7.1      Describe THREE advantages of using a turbocharger on an
                      engine.                                                                      (3)

           6.7.2      Give TWO reasons why synthetic oil is used to lubricate
                      turbochargers.                                                               (2)

           6.7.3      Which type of turbocharger does not have vanes?                              (1)

Copyright reserved                                                              Please turn over

### Page 11

Mechanical Technology: Automotive            11                            DBE/November 2024
                                       NSC Confidential

 6.8       Explain the following terms with regard to turbochargers:

           6.8.1      Boost                                                                      (2)

           6.8.2      Turbo lag                                                                  (2)

 6.9       FIGURE 6.9 below shows a supercharger. Answer the questions that follow.

                                                                       B

                        A
                                                                       C

                                           FIGURE 6.9

           6.9.1      Identify the type of supercharger.                                         (1)

           6.9.2      Label A–C.                                                                 (3)
                                                                                                 [28]

Copyright reserved                                                            Please turn over

### Page 12

Mechanical Technology: Automotive              12                       DBE/November 2024
                                         NSC Confidential

 QUESTION 7: FORCES (SPECIFIC)

 7.1       Define the following terms:

           7.1.1      Clearance volume                                                          (2)

           7.1.2      Compression ratio                                                         (2)

 7.2       Calculate the work done if a hoist needs to raise a vehicle weighing 690 kg
           to a height of 2 m.                                                                  (3)

 7.3       State TWO methods to lower the clearance volume on an internal
           combustion engine.                                                                   (2)

 7.4       FIGURE 7.4 below shows a cylinder. Answer the questions that follow.

                A = 79 mm
                B = 83 mm                                                    TDC
                CR = 9 : 1

                                                    B                    A

                                                                             BDC

                                             FIGURE 7.4

           7.4.1      Label distances A and B.                                                  (2)

           7.4.2      Calculate the swept volume in the cylinder in cm3 when
                      A = 79 mm and B = 83 mm.                                                  (3)

           7.4.3      Calculate the clearance volume of the cylinder.                           (3)

 7.5       The following data was recorded during a test carried out on a four-stroke
           four-cylinder petrol engine:

           Mean effective pressure:      1 400 kPa
           Stroke:                       110 mm
           Bore diameter:                100 mm
           Engine revolutions:           3 600 r/min

           Calculate the indicated power in kW.                                                 (7)

Copyright reserved                                                           Please turn over

### Page 13

Mechanical Technology: Automotive           13                         DBE/November 2024
                                      NSC Confidential

 7.6       The indicated power of a two-stroke engine is 50 kW at 2 000 r/min. It has
           a cylinder bore diameter of 35 mm with a stroke length of 40 mm. The force
           required to stop the flywheel is 50 N with a brake arm length of 350 mm.

           Calculate the following:

           7.6.1      Torque                                                                  (3)

           7.6.2      Brake power in kW                                                       (3)

           7.6.3      Mechanical efficiency                                                   (2)
                                                                                              [32]

Copyright reserved                                                         Please turn over

### Page 14

Mechanical Technology: Automotive             14                        DBE/November 2024
                                        NSC Confidential

 QUESTION 8: MAINTENANCE (SPECIFIC)

 8.1       TABLE 8.1 below shows information regarding the results of the exhaust gas
           analysis of an internal combustion engine.

           Complete TABLE 8.1 by giving ONE cause and ONE appropriate corrective
           measure for EACH fault. Write only the answer next to the question numbers
           (8.1.1 to 8.1.4) in the ANSWER BOOK.

                                                                  CORRECTIVE
             FAULTS (READING)           POSSIBLE CAUSES
                                                                   MEASURES
           High carbon monoxide
                                                8.1.1                  8.1.2
           (CO) reading
           Low carbon dioxide
                                                8.1.3                  8.1.4
           (CO2) reading
                                            TABLE 8.1                                          (4)

 8.2       The readings below were taken during a compression test on a
           four-cylinder internal combustion engine. Answer the questions that follow.

           Cylinder 1:       9 bars
           Cylinder 2:       7,1 bars
           Cylinder 3:       8,7 bars
           Cylinder 4:       8,9 bars

           8.2.1      What is the maximum variation allowed, in percentage (%),
                      between the compression readings?                                        (1)

           8.2.2      State ONE possible cause and its corrective measure for the low
                      reading in cylinder 2.                                                   (2)

 8.3       Identify FOUR locations where leakages can be detected during a cylinder
           leakage test.                                                                       (4)

 8.4       State FOUR causes of a low oil-pressure reading on an internal combustion
           engine.                                                                             (4)

 8.5       State TWO possible causes and the corrective measures for a high
           fuel-pressure reading during a fuel pressure test.                                  (4)

 8.6       State TWO manufacturers' specifications required before performing a
           cooling system pressure test.                                                       (2)

 8.7       State TWO functions of the radiator cap.                                            (2)
                                                                                               [23]

Copyright reserved                                                          Please turn over

### Page 15

Mechanical Technology: Automotive            15                        DBE/November 2024
                                       NSC Confidential

 QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)

 9.1       State TWO disadvantages of a vehicle fitted with an automatic gearbox when
           compared to a manual gearbox.                                                      (2)

 9.2       Explain the operation of a torque converter.                                       (5)

 9.3       Draw a single epicyclic gear system and label the FOUR basic components.           (5)

 9.4       State ONE advantage of using EACH of the following gear ratios in the
           gearbox of a motor vehicle:

           9.4.1      Forward reduction (1st gear)                                            (1)

           9.4.2      Reverse gear                                                            (1)

           9.4.3      Forward overdrive (5th gear)                                            (1)

 9.5       State ONE use of EACH of the following components with regard to an
           automatic gearbox:

           9.5.1      Hydraulic pistons                                                       (1)

           9.5.2      Brake bands                                                             (1)

           9.5.3      Transmission control unit                                               (1)
                                                                                              [18]

Copyright reserved                                                         Please turn over

### Page 16

Mechanical Technology: Automotive             16                            DBE/November 2024
                                        NSC Confidential

 QUESTION 10:        SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY AND
                     ELECTRONICS) (SPECIFIC)

 10.1      FIGURE 10.1 below shows a tyre wear pattern. Answer the questions that
           follow.

                                         One side of tyre
                                           tread worn
                                          excessively

                                             FIGURE 10.1

           10.1.1     Which wheel alignment angle will cause the tyre wear pattern
                      shown?                                                                      (1)

           10.1.2     State TWO faults on the vehicle suspension that could cause this
                      tyre wear.                                                                  (2)

           10.1.3     Describe TWO ways to correct the cause of this tyre wear.                   (2)

 10.2      Define the following wheel alignment angles:

           10.2.1     Positive caster                                                             (2)

           10.2.2     King pin inclination                                                        (2)

 10.3      Name THREE sensors found on an air-intake system of an internal
           combustion engine.                                                                     (3)

 10.4      What is the function of the knock sensor fitted to the engine?                         (2)

 10.5      Name TWO components of a distributorless ignition system (DIS).                        (2)

 10.6      Name TWO chemical reactions that occur in the catalytic convertor.                     (2)

 10.7      State TWO functions of the speed control system.                                       (2)

Copyright reserved                                                             Please turn over

### Page 17

Mechanical Technology: Automotive             17                           DBE/November 2024
                                        NSC Confidential

 10.8      FIGURE 10.8 below shows an exploded view of an alternator. Answer the
           questions that follow.

                                                                   Regulator

               A                    C            Rotor                 Rectifier
                                        D
                           B
                                            FIGURE 10.8

           10.8.1     Label A–D.                                                               (4)

           10.8.2     What is the function of the rotor?                                       (2)

           10.8.3     What does the regulator control in the alternator?                       (1)

           10.8.4     What is the function of the rectifier?                                   (2)

 10.9      State THREE factors that influence the amount of fuel sprayed by the
           injector.                                                                       (3)
                                                                                           [32]

                                                                               TOTAL:          200

Copyright reserved

### Page 18

Mechanical Technology: Automotive                  1                      DBE/November 2024
                                             NSC Confidential

        FORMULA SHEET FOR MECHANICAL TECHNOLOGY: AUTOMOTIVE

   1.          F  ma

              Where:
                         m = Mass
                         a = Acceleration

   2.          Work done = Force × Displacement                 OR   W Fs

                            Force  Displacement                          Fs
   3.          Power                                           OR   P
                                    Time                                   t

   4.          Torque  Force  Radius                          OR   T Fr

   5.          IP  P  L  A  N  n

               Where:

                         IP  Indicated power
                         P  Mean effective pressure
                         L  Stroke length
                         A  Area of piston crown
                         N  Number of power strokes per second
                          n  Number of cylinders

   6.          BP = 2 π N T

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     T     Torque

   7.          Brake power with Pröny brake = 2  π  N  F  R

               Where:

                     BP  Brake power
                     N  Revolution s per second
                     F  Force
                     R  Brake arm length

Copyright reserved                                                           Please turn over

### Page 19

Mechanical Technology: Automotive                2                 DBE/November 2024
                                           NSC Confidential

                                          BP
   8.          Mechanical efficiency =        100%
                                          IP

                                       SV  CV
   9.          Compression ratio 
                                         CV

               Where:

                     SV  Swept volume
                     CV  Clearance volume

                    πD 2
   10.         SV =      L
                     4

               Where:
                     D  Bore diameter
                     L  Stroke length

                        SV
   11.         CV =
                       CR - 1

                                Product of teeth on driven gears
   12.         Gear ratio =
                                Product of teeth on driver gears

Copyright reserved

## Related documents

- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Mechanical Technology · Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Mechanical Technology · Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Mechanical Technology · Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Mechanical Technology · Memo · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-english/2c18efa9-a7cc-42c1-a732-2ff3511c8c1c) — Mechanical Technology · Memo · 2024 · Eng
- [Mechanical Technology May-June 2024 (Fitting and Machining) MG Afr](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-memorandum-afrikaans/03c703c8-8125-4d5a-a124-37013b381c7a) — Mechanical Technology · Memo · 2024 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [Mechanical Technology May-June 2024 (Welding and Metalwork) MG Afr](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-memorandum-afrikaans/552ebeca-d294-4c37-b3fb-cded79fa438f) — Memo · 2024 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-afrikaans/f45c553c-63a1-4e1c-b9c6-d426a3dfef26) — Memo · 2023 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Memo · 2023 · Eng
- [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Memo · 2023 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
