# Mechanical Technology Grade 12 November 2024 NSC Memo (Eng)

> Grade 12 Mechanical Technology memorandum from the November 2024 NSC (English), 23 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594
- Updated: 2026-10-29
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Memorandum
- Year: 2024
- Exam period: November 2024 NSC
- Curriculum: CAPS
- Pages: 23

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 November 2024 NSC Memo (Eng)](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594)

## About this document

Mechanical Technology · Grade 12 · November 2024 NSC · 2024. Memorandum. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

NATIONAL
                              SENIOR CERTIFICATE

                                    GRADE 12

           MECHANICAL TECHNOLOGY: FITTING AND MACHINING

                                  NOVEMBER 2024

                              MARKING GUIDELINES

MARKS: 200

                     These marking guidelines consist of 23 pages.

Copyright reserved                                                   Please turn over

### Page 2

Mechanical Technology: Fitting and Machining  2                  DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 1: MULTIPLE-CHOICE (GENERIC)

 1.1        A✓                                                                         (1)

 1.2        D✓                                                                         (1)

 1.3        A✓                                                                         (1)

 1.4        B✓                                                                         (1)

 1.5        D✓                                                                         (1)

 1.6        C✓                                                                         (1)
                                                                                       [6]

Copyright reserved                                                  Please turn over

### Page 3

Mechanical Technology: Fitting and Machining  3                           DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 2: SAFETY (GENERIC)

 2.1       Horizontal band saw (Already been switched on):
           • Never leave the band saw unattended while in motion. ✓
           • Switch off the band saw when leaving. ✓
           • Use a brush or wooden rod to remove chips/swarf/filings. ✓
           • When reaching around a revolving band saw, be careful that your clothes
              do not get caught in the blade. 
           • Don't stop a revolving bandsaw blade with your hand. ✓
           • Don't adjust the band saw while working. ✓
           • Don't open any guard while in motion. ✓
           • Keep hands away from action points. ✓
           • Do not force the band saw blade into the material. ✓
           • Apply cutting fluid if required. ✓
           • Avoid overcrowding of persons around the machine. ✓
           • Do not lean on the machine. ✓
           • Check if the machine is running smoothly. ✓
                                                                         (Any 2 x 1)          (2)

 2.2       First aid basic treatment:
           • Examination ✓
           • Diagnosis ✓
           • Treatment ✓                                                                      (3)

 2.3       Oxygen fittings with oil and grease:
           It forms a flammable mixture. ✓                                                    (1)

 2.4       Disadvantages of the process layout:
           • Production is not always continuous. ✓
           • Transportation costs between process departments may be high. ✓
           • Additional time is spent in testing and sorting as the product moves to
              the different departments. ✓
           • Damage to fragile goods may result from extra handling. ✓
                                                                         (Any 2 x 1)          (2)

 2.5       Advantages of the product layout:
           • Handling of material is limited to a minimum. ✓
           • Time period of manufacturing cycle is less. ✓
           • Production control is almost automatic. ✓
           • Control over operations is easier. ✓
           • Greater use of unskilled labour is possible. ✓
           • Less total inspection is required. ✓
           • Less total floor space is needed per unit of production. ✓
                                                                            (Any 2 x 1)       (2)
                                                                                               [10]

Copyright reserved                                                            Please turn over

### Page 4

Mechanical Technology: Fitting and Machining  4                           DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 3: MATERIALS (GENERIC)

 3.1       Filing test:

           3.1.1      Files easily                                                           (1)

           3.1.2      Hard to file                                                           (1)

           3.1.3      Files easily                                                           (1)

 3.2       Heat treatment:

           It is the heating  and cooling  of metals under controlled conditions / as
           to change their properties.                                                       (3)

 3.3       Heating of metal:

           If metal is heated too fast, the outside of the metal becomes hotter  than
           the inside,  then it is very difficult  to achieve a uniform structure.         (4)

 3.4       Case hardening:

           •   Low-carbon steel / Mild steel 
           •   Low-alloy steel                                                               (2)

 3.5       Tempering:

           •   It is to relieve the strains induced during the hardening process. 
           •   Increase toughness. 
           •   Decrease brittleness. 
           •   Achieve a finer grain structure. 
                                                                             (Any 1 x 2)      (2)
                                                                                              [14]

Copyright reserved                                                            Please turn over

### Page 5

Mechanical Technology: Fitting and Machining  5                  DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 4: MULTIPLE-CHOICE (SPECIFIC)

 4.1       B✓                                                                        (1)

 4.2       A✓                                                                        (1)

 4.3       B✓                                                                        (1)

 4.4       C✓                                                                        (1)

 4.5       D✓                                                                        (1)

 4.6       D✓                                                                        (1)

 4.7       C✓                                                                        (1)

 4.8       A✓                                                                        (1)

 4.9       B✓                                                                        (1)

 4.10      C✓                                                                        (1)

 4.11      A✓                                                                        (1)

 4.12      D✓                                                                        (1)

 4.13      A✓                                                                        (1)

 4.14      C✓                                                                        (1)
                                                                                     [14]

Copyright reserved                                                   Please turn over

### Page 6

Mechanical Technology: Fitting and Machining  6                               DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)

 5.1       Disadvantages:
           • The automatic feed of the machine cannot be used. 
           • Only short length tapers can be cut. 
           • It causes fatigue in the operator. 
           • Poor finish. 
                                                                               (Any 3 x 1)        (3)

 5.2       Taper calculations:

           5.2.1      Small diameter:
                                 θ D −d                                     x
                              tan =                              tan 3,5 =
                                 2    2l                                  368
                                    7 85 − d                    x = 368 tan 3,5 
                                 tan  =
                                    2 2  368                   x = 22,51 mm 
                                                         OR
                         736  tan3,5 = 85 − d
                                                                 d = D − 2x
                                 45,02 = 85 − d
                                                                 d = 85 − 2 (22,5 ) 
                                         d = 85 − 45,02
                                                                 d = 39,98 mm 
                                         d = 39,98 mm                                            (4)

           5.2.2      Set-over of the tailstock:
                                   L (D − d)
                      Set − over =
                                      2l
                                         488 (85 − 39,98) 
                                     =
                                             2  368 
                                     = 29,85 mm                                                  (3)

 5.3       Key ways:

           5.3.1      Width:
                                 D
                       Width =
                                 4

                                 105
                       Width =       
                                  4

                              = 26, 25 mm                                                        (2)

Copyright reserved                                                                Please turn over

### Page 7

Mechanical Technology: Fitting and Machining  7                         DBE/November 2024
                                      NSC – Marking guidelines

           5.3.2      Thickness:
                                      D
                       Thickness =
                                      6

                                     105
                       Thickness =       
                                      6

                                   = 17,50 mm                                              (2)

           5.3.3      Length:
                      Length = 1,5  diamter of shaft
                             = 1,5  105 
                             = 157,50 mm                                                   (2)

 5.4       Safety milling:
           • Do not use your hands to remove cuttings while the machine is in
              motion. 
           • Use a brush once the machine has stopped. 
           • Resist the habit of leaning on machinery. 
           • Do not talk to anyone while you are operating the machine. 
           • Place saw dust, or oil-absorbing compounds on slippery floors. 
           • Use a piece of leather or cloth for protection when you handle milling
              cutters. / Do not use your bare hands when you handle milling cutters. 
           • Use safety goggles when cutting. 
           • Do not reach over or near rotating cutters. 
           • Never leave the machine running unattended. 
           • Make sure all guards are in place. 
           • Do not use the machine or come close to its moving parts while wearing
              loose clothes. 
           • Never use an air hose to clean the milling machine. 
           • Stop the machine before you make any adjustments or take
              measurements. 
           • Check that there is no oil or grease on the floor around the machine. 
           • Always clamp workpieces and holding devices safely and firmly. 
           • Do not use excessive force on the workpiece. 
                                                                           (Any 2 x 1)         (2)
                                                                                               [18]

Copyright reserved                                                          Please turn over

### Page 8

Mechanical Technology: Fitting and Machining  8                                   DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)

 6.1       Gear terminology:

           6.1.1      Circular pitch:
                        CP = m π
                             =3π 
                             = 9, 42 mm                                                              (2)

           6.1.2      Number of teeth:
                          PCD                                         CP  T
                      m=                                    PCD =
                            T                                           π
                          PCD                                         9, 42  T
                      T =                                   186 =                
                           m                    OR                        π
                          186                                         186  π
                      T =                                       T=               
                           3                                           9, 42
                      T = 62 teeth 
                                                                  = 62 teeth                         (3)

           6.1.3      Dedendum:

                       Dedendum =1,157  m                       Dedendum =1,25  m
                                                      OR
                                    =1,157  3                                   =1,25  3 
                                    = 3,47 mm                                    = 3,75 mm 
                                                                                                      (2)

Copyright reserved                                                                    Please turn over

### Page 9

Mechanical Technology: Fitting and Machining  9                              DBE/November 2024
                                      NSC – Marking guidelines

 6.2       Dovetails:

           6.2.1      Maximum width distance of dovetail: (W)

                      Calculate DE or y:

                                                                           AD
                                                                  tan  =
                                DE                                         DE
                        tan  =
                                AD                                          32
                                                                 tan60  =     
                          DE = tan   AD            OR                   DE
                              = tan30  32                                  32
                                                                    DE =           
                             = 18,48 mm                                   tan60 
                                                                         = 18,48 mm 

                        W = 125 + 2(DE) 
                           = 125 + 2(18,48) 
                           = 125 + 36,96
                           = 161,96 mm                                                          (6)

Copyright reserved                                                               Please turn over

### Page 10

Mechanical Technology: Fitting and Machining 10                                 DBE/November 2024
                                      NSC – Marking guidelines

           6.2.2      Distance over the rollers: (M)

                      Calculate AC or x:

                                 BC
                       Tan =
                                 AC                                        AC
                                                                 Tan  =
                                                                           BC
                                  BC
                         AC =         ✓                            AC = Tan   BC ✓
                                 Tan
                                                     OR
                                   7                                  = Tan60 o  7 ✓
                             =           ✓
                                 Tan30 o
                                                                      =12,12 mm ✓
                             =12,12 mm ✓

                      M = w + [(2(AC) + 2(R)] ✓
                         = 125 + [2(12,12) + 2(7)] ✓
                         = 125 + (24,24 + 14)
                         = 163,24 mm ✓
                                  OR
                      M = w + 2(AC + R) ✓
                         = 125 + 2(12,12 + 7) ✓
                         = 125 + 24,24 + 14
                         = 163,24 mm ✓
                                 OR
                      M= w + 2(AC) + 2(R) ✓
                         = 125 + 2(12,12) + 2(7) ✓
                         = 125 + 24,24 + 14
                         = 163,24 mm ✓                                                                 (6)

Copyright reserved                                                                  Please turn over

### Page 11

Mechanical Technology: Fitting and Machining 11                            DBE/November 2024
                                      NSC – Marking guidelines

 6.3       Milling of spur gear:

           6.3.1      Indexing:
                                  40
                       Indexing =
                                   n
                                  40
                                =
                                  101
                                  40
                       Indexing =
                                   A
                                   40
                                =
                                  100 
                                  2 5
                                = 
                                  5 5 
                                  10
                                =     
                                  25
                      Approximate indexing:
                               No full turns and 10 holes on a 25-hole circle ✓
                                              OR
                               No full turns and 12 holes on a 30-hole circle ✓                  (4)

           6.3.2      Change gears:
                       Dr              40
                          = (A − n )                            Dr ( A − n ) 40
                       Dn              A                            =        
                       Dr        ✓         40                    Dn    A       1
                          = (100 − 101)                                  ✓
                       Dn                 100 ✓                  Dr (100 − 101) 40
                                                                    =            
                                  40                             Dn     100 ✓      1
                          = −1                       OR
                                 100                                     2 20
                            − 40                                    =−       ✓
                          =        ✓                                     5 20
                             100
                                                                 Dr   40 ✓
                       Dr     40 ✓                                  =
                          =                                      Dn 100 ✓
                       Dn 100 ✓                                                                      (5)
                                                                                                     [28]

Copyright reserved                                                                Please turn over

### Page 12

Mechanical Technology: Fitting and Machining 12                       DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)

 7.1       Different indenters:

           7.1.1      On the anvil/platform. ✓                                            (1)

           7.1.2        •   By calculation ✓
                        •   Using the table ✓                                             (2)

 7.2       Label A-D:

           A. Datum line/Reading line✓
           B. Fixed anvil ✓
           C. Thimble ✓
           D. Ratchet ✓                                                                   (4)

 7.3       Function of screw thread micrometer:

           To measure ✓ the pitch diameter ✓ of a screw thread.                           (2)

 7.4       Height of a screw thread:

           H = 0,866 × Pitch (P)
           H = 0,866 × 2,5 ✓
           H = 2,17 mm ✓                                                                  (2)

 7.5       Reading of depth micrometer:

           The depth micrometer reads in the opposite direction. / In a depth
           micrometer the reading is taken from right to left and a screw thread
           micrometer reads from left to right on the datum line. ✓                       (1)

 7.6       Interchangeable rods:

           •    Interchangeable rods are used to measure extra depth. ✓
           •    Interchangeable rods are used to measure more than 25 mm. ✓
                                                                        (Any 1 x 1)       (1)
                                                                                          [13]

Copyright reserved                                                        Please turn over

### Page 13

Mechanical Technology: Fitting and Machining 13                                                       DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 8: FORCES (SPECIFIC)

 8.1       System of forces:

                                                 45 N

                           25 sin 30°               45sin90°
                          25 N 25cos30°

                                                                           150 sin 30°
                                             60 º

                                                               30 º

                 80 sin 45°
                                          45 º

                                                      150cos30° 150 N
                                        80cos45°               N
                     80 N

                8.1.1 ∑ Horizontal component:

                                  HC = 45cos90  − 25cos30  − 80cos45  + 150cos30 
                                                ✓        ✓     ✓
                                  HC = 0 − 21,65 − 56,57 + 129,90

                                                                                                                             (4)
                                  HC = 51,68N ✓

                8.1.2 ∑ Vertical component:

                                  VC = 45sin90  + 25sin30  − 80sin45  − 150sin30 

                                        ✓     ✓      ✓       ✓
                                  VC = 45 + 12,5 − 56,57 − 75

                                                                                                                             (5)
                                  VC = − 74,07 N ✓

                                                                      OR
        Force         θ                 8.1.2 ∑VC/y = Fsinθ                              8.1.1 ∑HC/x = Fcosθ
        45N            90º              VC = 45sin90º      45 N ✓                        HC = 45cos90º     0N
        25N           150º              VC = 25sin150º     12,5 N ✓                      HC = 25cos150º    -21,65 N ✓
        80N           225º              VC = 80sin225º     - 56,57 N ✓                   HC = 80cos225º    -56,57 N ✓
        150N          330º              VC = 150sin330º    -75 N ✓                       HC = 150cos330º 129,90 N ✓
                                        Total              -74,07N ✓                                       51,68N ✓

Copyright reserved                                                                                        Please turn over

### Page 14

Mechanical Technology: Fitting and Machining 14                      DBE/November 2024
                                      NSC – Marking guidelines

           8.1.3 Resultant:
             R 2 = VC2 + HC2

             R2 =     ( −74,04 ) + ( 51,68 )
                                2              2
                                                   ✓

              R = 90,32 N ✓                                                              (2)

           8.1.4 Angle and direction of equilibrant:

                               VC
                     tan θ =
                               HC
                                                                 α
                                     − 74,07 
                         θ = tan −1          ✓
                                     51,68 
                         θ = 55,10° ✓

                               OR

                               HC
                     tan  =
                               VC
                                   51,68 
                          = tan −1        ✓
                                   − 74,07 
                          = 34,90° ✓

                 Direction:
                 E = 90,32 N 55,10° N from W ✓
                 OR
                                             ✓
                 E = 90,32 N 34,90° W from N
                 OR
                 E = At a Bearing of 325,10°                                             (3)

Copyright reserved                                                       Please turn over

### Page 15

Mechanical Technology: Fitting and Machining 15                             DBE/November 2024
                                      NSC – Marking guidelines

 8.2      Calculations, UDL and supports A and B.

           8.2.1      UDL:

                      UDL = 10 N/m x 4 m ✓
                      UDL = 40 N ✓                                                                 (2)

           8.2.2      Reaction in support A:
                      Take moments about B:
                                                    LHM =  RHM

                             ✓             ✓           ✓
                       ( 60 1,5 ) + ( 40  5 ) + ( 75  11) = ( A  12 )
                                           90 + 200 + 825 = 12A
                                                               1115
                                                           A=
                                                                12
                                                           A = 92,92 N ✓

                      Reaction in support B:
                      Take moments about A:
                        LHM =  RHM

                                       ✓           ✓             ✓
                       (B  12 ) = ( 75  1) + ( 40  7 ) + ( 60  10,5 )
                             12B = 75 + 280 + 630
                                     985
                                 B=
                                     12
                                 B = 82,08 N ✓                                                     (8)

 8.3       Stress calculations:

           8.3.1      Stress:

                          F
                       σ =
                          A
                            110000
                       σ=              ✓
                          7,07  10 -4
                       σ = 155586987, 3
                       σ = 155,59 MPa ✓                                                            (2)

Copyright reserved                                                              Please turn over

### Page 16

Mechanical Technology: Fitting and Machining 16                  DBE/November 2024
                                      NSC – Marking guidelines

           8.3.2      Diameter:

                          π d2
                       A=
                           4
                               4A
                       d=         ✓
                               π

                       d=
                               (
                             4 7,07  10 − 4   )
                                                   ✓
                                   π
                       d = 0,03 m  ✓
                       d = 30 mm ✓                                                      (4)

           8.3.3      The original length:

                          ΔL
                       ε=
                          oL
                             ΔL
                       oL =     ✓
                              ε
                              0,0001
                       oL =              ✓
                            1,64  10 -5
                       oL = 6,1 m
                       oL = 6097,56 mm ✓                                                (3)
                                                                                        [33]

Copyright reserved                                                   Please turn over

### Page 17

Mechanical Technology: Fitting and Machining 17                       DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 9: MAINTENANCE (SPECIFIC)

 9.1       Mechanical drives:

           •   Gear drive ✓
           •   Belt drive ✓
           •   Chain drive ✓
           •   Hydraulic drives ✓
           •   Pneumatic drives ✓
           •   Shaft drives ✓
                                                                        (Any 3 x 1)       (3)

 9.2       Maintenance on operating systems:

            • Maintenance is to ensure that the system/machine always operates ✓ at
              an optimal level. ✓
            • Prevent machinery from breakdown ✓ and let the machines last
              longer. ✓
                                                                        (Any 1 x 2)       (2)

 9.3       Preventative maintenance procedures on gear drives:

           •   Check and refill lubricant levels. ✓
           •   Ensure that gears are properly secured to shafts. ✓
           •   Cleaning and replacement of oil filters. ✓
           •   Reporting excessive noise and wear, vibration and overheating for
               expert attention. ✓
           •   Make sure that the gears are properly aligned. ✓
           •   Ensure that the correct type of oil/lubricant is used. ✓
                                                                        (Any 3 x 1)       (3)

 9.4       Subgroups of preventative maintenance:

           •   Planned/Scheduled maintenance ✓
           •   Condition-based maintenance ✓                                              (2)

 9.5       Polyester resins:

           To strengthen the glass fibre. ✓                                               (1)

 9.6       Lack of preventive maintenance:

           •   Risk of injury. ✓
           •   Risk of death. ✓
           •   Financial loss. ✓
           •   Damage of machines/equipment. ✓
           •   Poor performance of machines/equipment. ✓
           •   Loss of valuable production time. ✓
           •   Damage to material/work piece. ✓
                                                                        (Any 3 x 1)       (3)

Copyright reserved                                                        Please turn over

### Page 18

Mechanical Technology: Fitting and Machining 18                      DBE/November 2024
                                      NSC – Marking guidelines

 9.7       Thermo-hardened and thermoplastic composites:

           Thermo-hardened: This material cannot be re-heated ✓ to be softened,
           shaped and moulded.✓
           Thermoplastic: These plastics can be re-heated ✓ and therefore reshaped
           in various ways. ✓                                                            (4)
                                                                                         [18]

Copyright reserved                                                       Please turn over

### Page 19

Mechanical Technology: Fitting and Machining 19                          DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 10: JOINING METHODS (SPECIFIC)

 10.1      Square thread:

           10.1.1     Pitch diameter:

                                      Lead
                       P itch =
                                  Number of starts
                                  40
                             =         
                                  4
                             = 10 mm 

                                       P
                         P D = OD −
                                       2
                                   10
                             = 105 −  
                                    2
                             = 100 mm                                                         (4)

           10.1.2     Helix angle of the thread:

                                  L ead
                       T anθ =
                                  π P D
                                    40 
                       T anθ =
                                  π  100 
                            θ = tan−1 ( 0,127323954 ) 
                              = 7, 26                                                        (4)

           10.1.3     Leading angle:

                      Leading angle = 90° – (helix angle + clearance angle)
                                           = 90° – (7,26° + 4°) ✓
                                           = 78,74° ✓                                          (2)

           10.1.4     Following angle:

                      Following angle = 90° + (helix angle – clearance angle)
                                            = 90° + (7,26° – 4°) ✓
                                            = 93,26° ✓                                         (2)

Copyright reserved                                                              Please turn over

### Page 20

Mechanical Technology: Fitting and Machining 20                  DBE/November 2024
                                      NSC – Marking guidelines

 10.2      Square thread:
           A. Crest- /Outside- /Major- /Nominal diameter ✓
           B. Pitch- /Effective- /Mean diameter ✓
           C. Helix angle ✓
           D. Cutting tool ✓                                                         (4)

 10.3      Uses of square thread:
           • Power transmissions ✓
           • Vice screws ✓
           • Lathe lead and feed screws / half nuts ✓
           • Press screws ✓
           • Clamping devices ✓
           • Linear actuators ✓
           • Adjustment mechanisms ✓
           • Tapping and thread cutting ✓
           • Threaded spindles ✓
           • Lifting mechanisms ✓
                                                                  (Any 2 x 1)        (2)
                                                                                     [18]

Copyright reserved                                                   Please turn over

### Page 21

Mechanical Technology: Fitting and Machining 21                  DBE/November 2024
                                      NSC – Marking guidelines

 QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)

 11.1      Hydraulic systems:

           11.1.1     Fluid pressure:

                           F
                       P =
                           A
                           600
                       P =      ✓
                           0,2
                       P = 3000 Pa                                                  (2)

           11.1.2     Force applied:

                           f
                       P =
                           a
                       f =P a    ✓
                       f = 3000  0,018 ✓
                       f = 54 N ✓                                                    (3)

           11.1.3     Displacement l:

                       VPlunger = VRam
                       a    = AL
                           AL
                         =        ✓
                             a
                           0,2  0,03
                         =            ✓
                             0,018
                         = 0,333 m
                         = 333,3 mm ✓                                                (3)

 11.2      Hydraulic pressure:

           Pressure gauge ✓                                                          (1)

 11.3      Purpose of hydraulic filter:

           •   To restrict dirt in system. ✓
           •   To protect the pump. ✓
           •   Protect the valves. ✓
           •   Protect the actuators. ✓
                                                                  (Any 1 x 1)        (1)

Copyright reserved                                                   Please turn over

### Page 22

Mechanical Technology: Fitting and Machining 22                  DBE/November 2024
                                      NSC – Marking guidelines

 11.4      Hydraulic valve:

           11.4.1     Identify valve:
                       • Non-return valve ✓
                       • One-way valve ✓
                                                                   (Any 1 x 1)       (1)

           11.4.2     Functions:
                      • Ensure one direction flow. ✓
                      • Prevent back flow. ✓
                      • Act as a pressure relief valve. ✓
                                                                   (Any 2 x 1)       (2)

 11.5      Belt drive:

           11.5.1     Rotational frequency:

                       NDN  D DN = NDR  D DR
                               NDN  D DN
                       NDR =                ✓
                                 D DR
                             1100  600 ✓
                       NDR =
                                220 ✓
                             3000 r/min
                       NDR =
                                 60
                       NDR = 50 r/sec ✓                                                 (4)

           11.5.2     Torque:

                          2  π  NT
                       Ρ=
                               60
                            P  60
                       T=           ✓
                           2 π  N
                            236,65  10 3  60
                       T=                      ✓
                              2  π  1100
                       T = 2054,40 Nm ✓                                                 (3)

Copyright reserved                                                   Please turn over

### Page 23

Mechanical Technology: Fitting and Machining 23                                DBE/November 2024
                                      NSC – Marking guidelines

 11.6      Gear drive:

           11.6.1       Rotational frequency of the output shaft NA in r/s:

                        Ninput        Product of the number of teeth on driven gears
                                  =
                        Noutput       Product of the number of teeth on driving gears
                           NA TB  TD
                             =        ✓
                           ND TA  TC
                          980 24  42 ✓
                             =
                          ND   45  20 ✓
                                      45  20  980
                           ND =
                                         24  42
                           ND = 875 r / min
                           ND = 14,58 r / sec ✓                                                    (4)

           11.6.2       Gear ratio:

                                          Product of teeth on driven gear
                        Gear ratio =
                                          Product of teeth on driver gear

                                          24  42 ✓
                        Gear ratio =
                                          45  20 ✓

                        Gear ratio = 1,12 : 1 ✓
                                          OR
                                          Ninput
                        Gear ratio =
                                          Noutput

                                          16,33 ✓        980 ✓
                        Gear ratio =              OR
                                          14,58 ✓        875 ✓

                        Gear ratio = 1,12 : 1 ✓

                                                                                                   (3)

 11.6.3    Direction:

           Clockwise ✓                                                                             (1)
                                                                                                   [28]

                                                                                    TOTAL:         200

Copyright reserved

## Related documents

- [Mechanical Technology Nov 2024 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-automotive-eng/5d2e2bd0-b02f-4218-849f-e7933bc6c4d1) — Mechanical Technology · QP · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) Afr](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-afr/1e7205e4-aef1-4cc4-afdf-aac93562ae67) — Mechanical Technology · QP · 2024 · Afr
- [Mechanical Technology May-June 2024 (Automotive) Eng](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-question-paper-english/10859467-be3e-41fb-aee0-b797c385437d) — Mechanical Technology · QP · 2024 · Eng
- [MECH TECH GR12 MEMO SEPT2023 Welding Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-afrikaans/f45c553c-63a1-4e1c-b9c6-d426a3dfef26) — Mechanical Technology · Memo · 2023 · Afr
- [MECH TECH GR12 MEMO SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2023-welding-english/b7ba3c6c-9153-4d83-8be0-0df7c4a69ab1) — Mechanical Technology · Memo · 2023 · Eng
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2023 English](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2023-english/dfc975c1-e179-4741-8d4f-e3b20c744c7e) — Mechanical Technology · Memo · 2023 · Eng

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MEC TECH GR12 MEMO SEPT2023 Fitting English](https://www.hlayiso.com/library/mec-tech-gr12-memo-sept2023-fitting-english/48945e78-f50a-4241-bab7-b94b61c60f49) — Memo · 2023 · Eng
- [MECH TECH GR12 QP SEPT2023 Welding English](https://www.hlayiso.com/library/mech-tech-gr12-qp-sept2023-welding-english/49e9215c-dc78-48c3-a526-4baaf59158d8) — QP · 2023 · Eng
- [Mechanical Technology May-June 2023 (Welding & Metalwork) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-welding-metalwork-afr/7d638feb-7218-4b3c-9f4c-ce95803d6e4f) — QP · 2023 · Afr
- [Mechanical Technology May-June 2023 (Automotive) Eng](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-eng/1523a16f-2012-4f13-a922-86cbb5900666) — QP · 2023 · Eng
- [Mechanical Technology May-June 2023 (Automotive) Afr](https://www.hlayiso.com/library/mechanical-technology-may-june-2023-automotive-afr/8d31d25d-e192-4aa9-b448-efab233391a1) — QP · 2023 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
