# Mechanical Technology Grade 12 NSC November 2020 QP (Eng)

> Grade 12 Mechanical Technology question paper from the NSC November Exam 2020 (English), 17 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/mt-nov-2020-welding-metalwork-eng/9c2d1e47-140c-449c-afc2-92673a7a5feb
- Updated: 2026-09-27
- Subject: Mechanical Technology
- Grade: Grade 12
- Document type: Question paper
- Year: 2020
- Exam period: NSC November Exam
- Curriculum: CAPS
- Pages: 17

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Mechanical Technology](https://www.hlayiso.com/library/grade-12/mechanical-technology) › [Mechanical Technology Grade 12 NSC November 2020 QP (Eng)](https://www.hlayiso.com/library/mt-nov-2020-welding-metalwork-eng/9c2d1e47-140c-449c-afc2-92673a7a5feb)

## About this document

Mechanical Technology · Grade 12 · NSC November Exam · 2020. Question paper, 17 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                          SENIOR CERTIFICATE/
                      NATIONAL SENIOR CERTIFICATE

                                  GRADE 12

        MECHANICAL TECHNOLOGY: WELDING AND METALWORK

                                NOVEMBER 2020

MARKS: 200

TIME: 3 hours

        This question paper consists of 16 pages and a 1-page formula sheet.

Copyright reserved                                                   Please turn over

### Page 2

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork         2                     DBE/November 2020
                                                  SC/NSC

INSTRUCTIONS AND INFORMATION

1.         Write your centre number and examination number in the spaces provided
           on the ANSWER BOOK.

2.         Read ALL the questions carefully.

3.         Answer ALL the questions.

4.         Number the answers correctly according to the numbering system used in
           this question paper.

5.         Start EACH question on a NEW page.

6.         Show ALL calculations and units. Round off final answers to TWO decimal
           places.

7.         Candidates may use non-programmable scientific calculators and drawing
           instruments.

8.         The value of gravitational acceleration should be taken as 10 m/s 2.

9.         All dimensions are in millimetres, unless stated otherwise in the question.

10.        Write neatly and legibly.

11.        A formula sheet is attached at the end of the question paper.

12.        Use the criteria below to assist you in managing your time.

                                                                                            TIME
QUESTION                               CONTENT                             MARKS
                                                                                         in minutes
                                      GENERIC
      1                       Multiple-choice Questions                      6                  6
      2                                 Safety                               10                10
      3                                Materials                             14                14
                                      SPECIFIC
       4                      Multiple-choice Questions                      14                10
       5                       Terminology (Templates)                       23                20
       6                        Tools and Equipment                          18                15
       7                                Forces                               45                30
       8                Joining Methods (Inspection of Welds)                23                20
       9              Joining Methods (Stresses and Distortion)              18                20
      10                             Maintenance                             9                 10
      11                     Terminology (Development)                       20                25
                                                             TOTAL          200               180

Copyright reserved                                                                Please turn over

### Page 3

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork      3                   DBE/November 2020
                                               SC/NSC

QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)

Various options are provided as possible answers to the following questions.
Choose the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 A.

1.1       What is the purpose of the Occupational Health and Safety Act, 1993
          (Act 85 of 1993) with regard to HIV/Aids awareness?

          A     The Act on safety states that all employers must make sure that the
                workplace is safe and that employees are not at risk of becoming
                infected with HIV at work.
          B     The Act contains common guidelines on how employers, employees
                and trade unions should respond to HIV in the workplace.
          C     Employers may not demote or promote employees based on their
                HIV status.
          D     Employers cannot simply dismiss a person who has been infected
                with HIV.                                                                (1)

1.2       Which ONE of the following pieces of personal protective equipment is
          applicable when using a drill press?

          A     Hard hat
          B     Apron
          C     Surgical gloves
          D     Safety goggles                                                           (1)

1.3       Which statement describes the placing of the machines in a product
          layout?

          A     The machines are arranged in the sequence in which operations are
                carried out.
          B     The machines are arranged according to the worker's skills.
          C     The machines are grouped according to their types of operation.
          D     The machines are arranged according to the products.                     (1)

1.4       Which heat-treatment process is used to give steel a high resistance
          against wear?

          A     Annealing
          B     Tempering
          C     Hardening
          D     Normalising                                                              (1)

1.5       The purpose of tempering steel is to…

          A     harden it.
          B     increase the toughness.
          C     soften it.
          D     cool it down.                                                            (1)

Copyright reserved                                                        Please turn over

### Page 4

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork        4                     DBE/November 2020
                                                 SC/NSC

1.6       Which test uses an indenter to determine the hardness of steel?

          A       Sound test
          B       Rockwell test
          C       Bending test
          D       Machining test                                                              (1)
                                                                                              [6]

QUESTION 2: SAFETY (GENERIC)

2.1       What safety rule must be adhered to after work procedures on a machine
          have been completed?                                                                (1)

2.2       State TWO safety precautions that must be adhered to after the horizontal
          band saw has been switched on.                                                      (2)

2.3       Give TWO reasons why surgical gloves must be worn when treating a
          co-worker with open wounds.                                                         (2)

2.4       State TWO pieces of personal protective equipment (PPE) which must be
          worn during arc welding.                                                            (2)

2.5       Describe the responsibility of an employer regarding the safety and health
          of the employees in the workplace.                                                  (2)

2.6       Who is responsible for administering first aid to an injured person at the
          workplace?                                                                          (1)
                                                                                              [10]

QUESTION 3: MATERIALS (GENERIC)

3.1       Explain how you will conduct the following tests to identify various metals:

          3.1.1        Sound test                                                             (2)

          3.1.2        File test                                                              (2)

3.2       What is the purpose of the heat treatment of steel?                                 (2)

3.3       What is the purpose of the case hardening of steel?                                 (2)

3.4       Describe the tempering process of steel.                                            (3)

3.5       Name the THREE factors which need to be taken into consideration when
          heat treatment of steel is done.                                                    (3)
                                                                                              [14]

Copyright reserved                                                             Please turn over

### Page 5

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork           5                DBE/November 2020
                                                    SC/NSC

QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)

Various options are provided as possible answers to the following questions.
Choose the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 A.

4.1       Which ONE of the following machine tools is used in the template loft?

          A     Welding machine
          B     Drilling machine
          C     Grinding machine
          D     Guillotine                                                                     (1)

4.2       Which weld position is indicated by the weld symbol in FIGURE 4.2?

                                               FIGURE 4.2

          A     Weld on both sides
          B     Weld on arrow side
          C     Weld on other side
          D     Weld on top side                                                           (1)

4.3       Which ONE of the following is used by a hydraulic press in
          its operation?

          A     Air
          B     Water
          C     Oil
          D     Grease                                                                     (1)

4.4       The purpose of inert gas in MIGS/MAGS welding is to …

          A     hold a work piece together during welding.
          B     protect the flux-coated electrode.
          C     create a molten pool for electrode feed.
          D     shield the molten pool from atmospheric gases.                             (1)

Copyright reserved                                                          Please turn over

### Page 6

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork           6            DBE/November 2020
                                                    SC/NSC

4.5       Identify the welding process shown in FIGURE 4.5 below:

                                               FIGURE 4.5

          A     Arc welding
          B     Spot welding
          C     Oxy-acetylene welding
          D     Gas welding                                                           (1)

4.6       FIGURE 4.6 below shows a blowtorch. Component X indicated on the
          diagram is the …

                                                        X

                                               FIGURE 4.6

          A     nozzle.
          B     oxygen valve.
          C     torch body.
          D     mixing chamber.                                                       (1)

Copyright reserved                                                     Please turn over

### Page 7

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork           7                  DBE/November 2020
                                                    SC/NSC

4.7       FIGURE 4.7 below shows the stress-strain graph obtained during a tensile
          test on mild steel. What is indicated by P in the graph?

                                                     P

                                Stress

                                                Strain

                                               FIGURE 4.7

          A     Maximum stress
          B     Break stress
          C     Elasticity limit
          D     Yield point                                                                 (1)

4.8       Original length is defined as the …

          A     ratio between stress and strain.
          B     length by which an object is shortened or lengthened.
          C     length of an object before an external load is applied.
          D     length of an object after an external load is applied.                      (1)

4.9       Identify the type of machine is shown in FIGURE 4.9 below:

                                               FIGURE 4.9

          A     Hydraulic press
          B     Power-driven press
          C     Drill press
          D     Fly press                                                                   (1)

Copyright reserved                                                           Please turn over

### Page 8

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork       8                     DBE/November 2020
                                                SC/NSC

4.10      Which ONE of the following determines the effect on shrinkage when
          performing arc welding?

          A     Amount of gas
          B     Surface area
          C     Type of electrode
          D     Type of spark                                                               (1)

4.11      Ultrasonic inspection techniques use … to detect flaws in welded joints.

          A     liquid dye
          B     sound waves
          C     X-rays
          D     light rays                                                                  (1)

4.12      The maximum plate thickness that can be cut with a manual guillotine is …

          A     2 mm.
          B     3 mm.
          C     1,2 mm.
          D     1,3 mm.                                                                     (1)

4.13      FIGURE 4.13 below indicates a procedure performed on a grinding wheel.
          Which aspect is addressed with this procedure?

                                           FIGURE 4.13

          A     Checking for cracks in the grinding wheel
          B     Investigating the sidewalls of the grinding wheel
          C     Determining the coarseness of the grinding wheel
          D     Checking the roundness of the grinding wheel                                (1)

Copyright reserved                                                           Please turn over

### Page 9

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork            9                DBE/November 2020
                                                     SC/NSC

4.14      Calculate the value of , as indicated in FIGURE 4.14 below:

                                                      5 cm

                                                   4 cm

                                           FIGURE 4.14

          A       53,12°
          B       38,66°
          C       53,13°
          D       36,87°                                                                    (1)
                                                                                            [14]

QUESTION 5: TERMINOLOGY (TEMPLATES) (SPECIFIC)

5.1       Name TWO advantages of using templates.                                           (2)

5.2       State ONE use of a template made from EACH of the following materials:

          5.2.1       Thin metal                                                            (1)

          5.2.2       Hardboard                                                             (1)

5.3       FIGURE 5.3 below shows a roof truss. Label parts A–E.

                                   B
                       A                                                      C

                                               E                         D

                                               FIGURE 5.3                                   (5)

Copyright reserved                                                           Please turn over

### Page 10

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork          10                DBE/November 2020
                                                    SC/NSC

5.4       A mild steel ring with an outside diameter of 280 mm must be fabricated
          from 12 x 12 mm square bar. Calculate the dimensions of the required
          material to fabricate the steel ring.                                            (5)

5.5       What does the abbreviation SANS stand for?                                       (2)

5.6       Identify the resistance weld symbols in FIGURES 5.6.1 and 5.6.2 below.

          5.6.1

                                                  FIGURE 5.6.1                             (1)

          5.6.2

                                                  FIGURE 5.6.2                             (1)

5.7       State the meaning of the dimensions of the weld indicated in FIGURE 5.7
          below.

                                  5       25-50
                                  -

                                               FIGURE 5.7                                  (3)

5.8       Identify the positions of the welds, as indicated by the welding symbols in
          FIGURES 5.8.1 and 5.8.2 below.

          5.8.1

                                                  FIGURE 5.8.1                             (1)

          5.8.2

                                                  FIGURE 5.8.2                             (1)
                                                                                           [23]

Copyright reserved                                                          Please turn over

### Page 11

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork          11                DBE/November 2020
                                                    SC/NSC

QUESTION 6: TOOLS AND EQUIPMENT (SPECIFIC)

6.1       FIGURE 6.1 below shows a pedestal drill. Label parts A–D.

                                                                   C
                               B
                                                                  D
                           A

                                               FIGURE 6.1                                  (4)

6.2       Explain the operating principles of the following machines that are used in
          the welding workshop:

          6.2.1       Horizontal band saw                                                  (4)

          6.2.2       Punch and shear (cropper) machine                                    (3)

6.3       Name THREE primary functions of flashback arresters fitted to the gas
          cylinders of oxy-acetylene equipment.                                            (3)

6.4       Name FOUR uses of taps and dies in the mechanical workshop.                      (4)
                                                                                           [18]

Copyright reserved                                                          Please turn over

### Page 12

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork            12                      DBE/November 2020
                                                      SC/NSC

QUESTION 7: FORCES (SPECIFIC)

7.1       FIGURE 7.1 below shows a steel framework. Answer the questions that
          follows.

          SCALE: Space diagram: 1 : 100
                 Force/Vector diagram: 1 mm = 10 kN
                 Tolerance: ± 3 mm

                                                500 kN

                            300 kN      B                    C   200 kN

                                            G            H                D
                       A
                              F                                   I
                      30°                                                 30°
                                                  E
                                                10 000
             525 kN                                                             475 kN
                                                FIGURE 7.1

          7.1.1       Determine graphically the force vector diagram of FIGURE 7.1
                      using scale 1 mm = 10 kN. (Redraw the space diagram and use
                      scale 1 : 100.)                                                             (10)

          7.1.2       Determine the magnitude and nature of the members, as shown
                      in FIGURE 7.1.                                                              (18)

Copyright reserved                                                                 Please turn over

### Page 13

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork          13                  DBE/November 2020
                                                    SC/NSC

7.2       FIGURE 7.2 below shows a simply supported beam with TWO point loads.

                                4 kN                         2 kN
                       3m                         4m                  3m

           A                                                 C                     D
                                  B

         RL = 3,4 kN                                                       RR = 2,6 kN

                                               FIGURE 7.2

          7.2.1       Calculate the bending moments at points B, C and D.                    (6)

          7.2.2       Draw a shear force diagram.                                            (3)

          7.2.3       Draw a bending moment diagram.

                      SCALE: Space diagram: 1 : 100
                             Shear force diagram: 5 mm = 1 kN
                             Bending moment diagram: 5 mm = 1 kNm
                             Tolerance: ± 3 mm                                               (3)

7.3       A round steel bar with a cross-sectional area of 80 mm2 resists a maximum
          force of 8 kN when subjected to a tensile test. The safety factor is 4.

          7.3.1       Calculate the maximum stress in the bar material.                      (3)

          7.3.2       Calculate the safe working stress of the bar.                          (2)
                                                                                             [45]

Copyright reserved                                                            Please turn over

### Page 14

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork       14                    DBE/November 2020
                                                 SC/NSC

QUESTION 8: JOINING METHODS (INSPECTION OF WELDS) (SPECIFIC)

8.1       State FOUR causes of spatter as a welding defect that occurs during the
          welding process.                                                                  (4)

8.2       Briefly describe the effect of EACH of the following on the quality of a gas
          cut surface:

          8.2.1       Nozzle too far from the surface                                       (2)

          8.2.2       Nozzle too close to the surface                                       (2)

8.3       Describe TWO causes of EACH of the following weld defects:

          8.3.1       Porosity                                                              (2)

          8.3.2       Poor penetration                                                      (2)

8.4       Name TWO causes of cracks in the heat-affected zone (HAZ).                        (2)

8.5       Name THREE elements that should be inspected during the visual
          inspection of arc-welded joints.                                                  (3)

8.6       Describe the procedures to be followed when performing an ultrasonic test
          on a welded joint.                                                                (6)
                                                                                            [23]

Copyright reserved                                                           Please turn over

### Page 15

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork          15              DBE/November 2020
                                                    SC/NSC

QUESTION 9: JOINING METHODS (STRESSES AND DISTORTION) (SPECIFIC)

9.1       What is residual stress?                                                      (2)

9.2       Describe the effect of hot working on steel.                                  (4)

9.3       Study FIGURE 9.3 below and answer the questions that follow.

                                                    B

           A                                                     C

                                 D

                                                     E

                                               FIGURE 9.3

          9.3.1       Identify the diagram in FIGURE 9.3.                               (1)

          9.3.2       Label A–E indicated on the diagram.                               (5)

9.4       State TWO results when metal is cooled rapidly.                               (2)

9.5       Name FOUR quenching media used for the heat treatment of steel.               (4)
                                                                                        [18]

QUESTION 10: MAINTENANCE (SPECIFIC)

10.1      Name TWO types of maintenance procedures on machines in the welding
          workshop.                                                                     (2)

10.2      Why is lock-out applied to machines during maintenance?                       (2)

10.3      State TWO rules to be observed before a machine start-up.                     (2)

10.4      Name THREE factors to be observed when selecting the cutting speed of
          a drilling machine.                                                           (3)
                                                                                        [9]

Copyright reserved                                                       Please turn over

### Page 16

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork           16           DBE/November 2020
                                                     SC/NSC

QUESTION 11: TERMINOLOGY (DEVELOPMENT) (SPECIFIC)

FIGURE 11 below shows a square-to-round transition piece.

                                           Ø 600

                                                              800

                         C           E       F           D
                                             G
                                             H
                                     I
                                 J

                     L       A
                                                              800
                                             K

                                            800

                                         FIGURE 11

Calculate:

11.1      True length CG                                                            (7)

11.2      True length CI                                                            (10)

11.3      True length JI                                                            (3)
                                                                                    [20]

                                                                       TOTAL:       200

Copyright reserved

### Page 17

Downloaded from hlayiso.com
Mechanical Technology: Welding and Metalwork                                              DBE/November 2020
                                                           SC/NSC

            FORMULA SHEET FOR MECHANICAL TECHNOLOGY
                    (WELDING AND METALWORK)
1.     STRESS AND STRAIN

                       Force                          F
           Stress                        or     σ
                       Area                           A

                       change in length                                        ΔL
           Strain                                    or                 ε
                        original length                                        L

                                        stress                                     σ
           Young' s mod ulus                          or                    E
                                        strain                                     ε

                       πd 2
           A shaft 
                        4

                    π(D 2  d 2 )
           A pipe 
                         4

2.     PYTHAGORAS THEOREM AND TRIGONOMETRIC RATIOS

                                                                             60°
                                    r
                                                 y                                        2 units

                                                                    1 unit
                                    x                                        90°                 30°
                                                                                    1 unit × 𝟑

                 y
        sin θ 
                 r
                 x
        cos θ 
                 r
                 y
         tan θ 
                 x
            r  x 2  y2
             2

3.     TEMPLATES AND DEVELOPMENTS

       Mean Ø = outside Ø – plate thickness                where Ø = diameter
       Mean Ø = inside Ø + plate thickness
       Mean circumference = π x mean Ø

Copyright reserved

## Related documents

- [MT Nov 2020 (Automotive) Eng](https://www.hlayiso.com/library/mt-nov-2020-automotive-eng/489fabb7-3cad-4d15-965e-29f7af36ce41) — Mechanical Technology · QP · 2020 · Eng
- [MT Nov 2020 (Fitting Machining) Afr](https://www.hlayiso.com/library/mt-nov-2020-fitting-machining-afr/52794b9f-ea5d-4bdb-884c-d52dbad5a518) — Mechanical Technology · QP · 2020 · Afr
- [MT Nov 2020 (Automotive) Afr](https://www.hlayiso.com/library/mt-nov-2020-automotive-afr/be2df9ff-ab68-45f4-9062-30f64c28e670) — Mechanical Technology · QP · 2020 · Afr
- [MT Nov 2020 (Fitting Machining) Eng](https://www.hlayiso.com/library/mt-nov-2020-fitting-machining-eng/11c0a6aa-a24c-4b21-afe1-f3bdeb598f17) — Mechanical Technology · QP · 2020 · Eng
- [MT Nov 2020 (Automotive) Memo Eng](https://www.hlayiso.com/library/mt-nov-2020-automotive-memo-eng/62bbe2de-9d39-485e-a55f-c51567c03422) — Mechanical Technology · Memo · 2020 · Eng
- [MT Nov 2020 (Fitting Machining) Memo Afr](https://www.hlayiso.com/library/mt-nov-2020-fitting-machining-memo-afr/c4d9ece6-0cba-42c1-a1e6-01ad8f18a69c) — Mechanical Technology · Memo · 2020 · Afr

## More from Grade 12 Mechanical Technology

- [Gr 12 Weld Met ATP 2023-24](https://www.hlayiso.com/library/gr-12-weld-met-atp-2023-24/8ecc8de5-c625-4611-9b94-1f3fd325e05d) — ATP
- [MECH TECH GR12 MEMO SEPT2024 (Welding & Metalwork) Afrikaans](https://www.hlayiso.com/library/mech-tech-gr12-memo-sept2024-welding-metalwork-afrikaans/aadd113c-5a3b-4f4d-a4c4-3a80cd86f882) — Memo · 2024 · Afr
- [MECHANICAL TECH (Auto) GR12 MEMO SEPT2024 Afrikaans](https://www.hlayiso.com/library/mechanical-tech-auto-gr12-memo-sept2024-afrikaans/2f874dd1-8c03-49a9-8c70-41ac528693d0) — Memo · 2024 · Afr
- [MECH TECH MEMO GR12 SEPT Fitting English](https://www.hlayiso.com/library/mech-tech-memo-gr12-sept-fitting-english/6c8e4f19-8a49-43c9-a4af-dbf620595837) — Memo · 2024 · Eng
- [Mechanical Technology Nov 2024 (Fitting and Machining) MG Eng](https://www.hlayiso.com/library/mechanical-technology-nov-2024-fitting-and-machining-mg-eng/ed5ab6d3-088f-425c-ade8-86186a031594) — Memo · 2024 · Eng
- [Mechanical Technology May-June 2024 (Fitting and Machining) MG Afr](https://www.hlayiso.com/library/grade-12-mechanical-technology-2024-nsc-june-exam-memorandum-afrikaans/03c703c8-8125-4d5a-a124-37013b381c7a) — Memo · 2024 · Afr

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
