# Technical Sciences Grade 12 P1 Eastern Cape Mock 2022 QP

> Grade 12 Technical Sciences Paper 1 question paper from the Eastern Cape Mock Exam 2022 (English), 17 pages. Read online or download the free PDF.

- Page: https://www.hlayiso.com/library/technical-sciences-p1-qp-gr12-sept2022-english/63d218ee-4843-43fe-a524-f271cef165f2
- Updated: 2026-09-27
- Subject: Technical Sciences
- Grade: Grade 12
- Language: English
- Document type: Question paper
- Year: 2022
- Exam period: Eastern Cape Mock Exam
- Paper: 1
- Curriculum: CAPS
- Pages: 17

Breadcrumbs: [Home](https://www.hlayiso.com/) › [Library](https://www.hlayiso.com/library) › [Grade 12](https://www.hlayiso.com/library/grade-12) › [Technical Sciences](https://www.hlayiso.com/library/grade-12/technical-sciences) › [Technical Sciences Grade 12 P1 Eastern Cape Mock 2022 QP](https://www.hlayiso.com/library/technical-sciences-p1-qp-gr12-sept2022-english/63d218ee-4843-43fe-a524-f271cef165f2)

## About this document

Technical Sciences · Grade 12 · Eastern Cape Mock Exam · 2022 · English. Question paper, 17 pages. Read online or download the PDF.

Read it free online on the page above; download the PDF from there.

## Document text

Text extracted from the PDF. Layout, diagrams and tables may not survive extraction.

### Page 1

Downloaded from hlayiso.com

                                NATIONAL
                           SENIOR CERTIFICATE

                                    GRADE 12

                            SEPTEMBER 2022

                    TECHNICAL SCIENCES P1

MARKS:   150

TIME:    3 hours

               This question paper consists of 17 pages, including 3 data sheets.

### Page 2

Downloaded from hlayiso.com
2                                  TECHNICAL SCIENCES P1           (EC/SEPTEMBER 2022)

INSTRUCTIONS AND INFORMATION

1.     Answer ALL the questions in the ANSWER BOOK.

2.     Write your NAME and SURNAME in the appropriate spaces on the
       ANSWER BOOK.

3.     Start EACH question on a NEW page in the ANSWER BOOK.

4.     Number the answers correctly according to the numbering system used in
       this question paper.

5.     You may use a non-programmable calculator.

6.     LEAVE a line open between two subsections, i.e. between QUESTION 2.1
       and QUESTION 2.2.

7.     You are advised to use the attached DATA SHEETS.

8.     Show ALL formulae and substitutions in ALL calculations.

9.     Round off your final numerical answers to a minimum of TWO decimal
       places.

10.    Give brief motivations, discussions, etc. where required.

11.    Write neatly and legibly.

Copyright reserved                                                    Please turn over

### Page 3

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)             TECHNICAL SCIENCES P1                                            3

 QUESTION 1: MULTIPLE-CHOICE QUESTIONS

 Various options are provided as answers to the following questions. Choose the
 answer and write only the correct letter (A–D) next to the question numbers
 (1.1 to 1.10) in the ANSWER BOOK, for example 1.11 D.

 1.1      Acceleration is defined as the rate of change of …

          A      speed.

          B      velocity.

          C      position.

          D      distance.                                                                 (2)

 1.2      A stationary minibus taxi has its sliding door open. When the taxi driver
          accelerates and then stops suddenly the sliding door closes without being
          pushed.

          The closing of the sliding door when the taxi stops is an illustration of …

          A      Hooke’s Law.

          B      Newton’s First Law.

          C      Newton’s Second Law.

          D      Newton’s Third Law.                                                       (2)

 1.3      A ball is dropped and falls vertically downwards. Ignore air resistance.

          Which ONE of the following graphs is CORRECT about mechanical
          energy (Emech) of the ball versus time (t)?

           A                                     B

                Emech                                   Emech
                (J)                                      (J)

                             t(s)                                     t(s)

           C                                     D

                Emech                                 Emech
                (J)                                   (J)

                             t(s)                                  t(s)
                                                                                           (2)

Copyright reserved                                                            Please turn over

### Page 4

Downloaded from hlayiso.com
4                                  TECHNICAL SCIENCES P1                  (EC/SEPTEMBER 2022)

 1.4     Three metal spheres P, Q and R of equal mass m, initially at rest are in
         contact with each other on a frictionless table. A fourth metal sphere S
         moving with velocity v to the right collides with sphere P and comes to
         rest.

         Immediately after the collision spheres Q and R move together with a
         combined kinetic energy equal to E. Sphere P remains at rest.

               BEFORE COLLISION                       AFTER COLLISION

           v            P, Q and R at rest        S and P at rest           v
                         m         m    m                  m         m      m

           S              P        Q      R       S        P          Q      R

         The collision is ELASTIC.

         What is the mass and kinetic energy of sphere S just before the collision
         if both spheres Q and R move at velocity v after the collision?

                                              KINETIC ENERGY OF SPHERE S
                     MASS OF SPHERE S
                                              JUST BEFORE THE COLLISION

         A                    2m                               E

         B                     m                               2E

         C                    ½m                               ½E

         D                    2m                               2E                       (2)

 1.5     A book is lying on a table. The reaction force to the NORMAL force
         acting on the book is the force exerted by the …
         A       book on the earth.

         B       table on the book.

         C       earth on the book.

         D       book on the table.                                                     (2)

 1.6     Which ONE of the following has the SI unit kg.m 2.s-3?
         A       Work x time

         B       Power x time

         C       Force x velocity

         D       Force x displacement                                                   (2)

Copyright reserved                                                           Please turn over

### Page 5

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)              TECHNICAL SCIENCES P1                                          5

 1.7    Which ONE of the following explains best why walls of dams are built
        THICKER at the bottom than at the top?

        A     Liquid pressure decreases with an increase in depth.

        B     Liquid pressure increases with an increase in depth.

        C     Density of a liquid decreases with an increase in depth.

        D     Density of a liquid increases with an increase in depth.                    (2)

 1.8    A light ray passes from glass to air. The angle of incidence is 35° and the
        critical angle of glass-air surface is 42°.

        Which ONE of the following is CORRECT about the path of the light ray?

        The light ray will undergo …

        A     total internal reflection.

        B     refraction towards the normal.

        C     neither reflection nor refraction.

        D     refraction away from the normal.                                            (2)

 1.9    Resistors in the circuit diagram given below are IDENTICAL.

        If voltmeter Y records a potential difference of V, then the reading on
        voltmeter X would be …

        A     2 V.

        B     V.

        C     ½ V.
        D     4 V.                                                                        (2)

Copyright reserved                                                           Please turn over

### Page 6

Downloaded from hlayiso.com
6                              TECHNICAL SCIENCES P1                  (EC/SEPTEMBER 2022)

 1.10     Which ONE of the following components in an electric motor enables the
          output current to flow in one direction?

          A      Magnets

          B      Slip rings

          C      Carbon brushes

          D      Split ring commutator                                               (2)
                                                                                    [20]

Copyright reserved                                                       Please turn over

### Page 7

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)            TECHNICAL SCIENCES P1                                          7

 QUESTION 2 (Start on a new page.)

 Two forces of 42 N and 10 N are applied SIMULTANEOUSLY on a stationary
 block of mass 2,4 kg as shown below. The 42 N force acts at an angle of 60° to
 the horizontal while the 10 N is a horizontal force to the left.

 The block experiences a kinetic frictional force of magnitude 6 N. The block moves
 to the right.

       42 N                                    Direction of motion

              60°              m = 2,4 kg              10 N

 2.1     Explain the following statement:

         ‘The stationary block has inertia.’                                            (2)

 2.2     State Newton’s Second Law in words.                                            (2)

 2.3     Draw a free-body diagram of all the forces acting on the block.                (5)

 2.4     Calculate the magnitude of the acceleration of the block.                     (5)
                                                                                      [14]

Copyright reserved                                                         Please turn over

### Page 8

Downloaded from hlayiso.com
8                               TECHNICAL SCIENCES P1                      (EC/SEPTEMBER 2022)

QUESTION 3 (Start on a new page.)

3.1     In the diagram below an air-rifle pellet of mass 2 g is fired into a stationary
        block of clay with a mass of 56 g. The pellet strikes the block at a speed of
        140 m·s-1 to the right.

                      Before the collision               After the collision

                   -1
           140 m·s
                                   m = 56 g
             m=2g

        3.1.1 Define the term isolated system.                                              (2)

        Upon impact, the pellet remains inside the block, and they move together as
        a single unit. Ignore the effects of friction.

        3.1.2 Will the total linear momentum of the block-bullet system change
              after the collision?

                Write down only YES or NO.                                                  (1)

        3.1.3 Calculate the velocity of the block-bullet system after impact.               (5)

3.2     During a safety test, a car of mass 800 kg travelling at 20 m.s -1 east hits a
        brick wall and comes to a stop. To bring the car to a stop the wall exerts a
        force of 1,6 x 103 N on the car.

        3.2.1 Define impulse.                                                               (2)

        3.2.2 Calculate the time taken for the car to stop.                                 (4)

        The brick wall is covered with a pack of mattresses and the same car, still
        travelling at 20 m.s-1, hits the mattresses and comes to a stop.

        3.2.3 How will the force of the mattresses on the car compare to the
              1,6 x 103 N force exerted by the brick wall on the car?

                Write only SMALLER THAN, GREATER THAN or SAME AS.

                Explain the answer.                                                        (4)
                                                                                          [18]

Copyright reserved                                                             Please turn over

### Page 9

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)                TECHNICAL SCIENCES P1                                             9

 QUESTION 4 (Start on a new page.)

 4.1      A girl pushes a 6,5 kg box across a rough floor by applying a 20 N force
          to the east. The coefficient of kinetic friction between the box and the floor
          is 0,1.

          The block moves a distance of 0,2 m.
                                                                                  N

                         20 N                                           W             E
                                        6,5 kg
                                                                                  S

          4.1.1       Define energy.                                                            (2)

          4.1.2       Write down the names of TWO forces that act on the block but do
                      NO work on the box as it moves over the distance of 0,2 m.                (2)

          Calculate the:

          4.1.3       Work done by the girl on the box                                          (3)

          4.1.4       Net work done on the box                                                  (5)

 4.2      A construction worker demolishes a brick wall by using a spherical metal
          ball of mass 1 500 kg. The cable attached to the ball is fixed at point O.

                                            O

                                                 3m
                            3m
                                            1m

                            Rest position

          The ball which is suspended from the cable, is first raised to a height of
          3 m above its rest position and then released from rest to strike the wall.
          Ignore the effects of air friction.

          4.2.1       State the principle of conservation of mechanical energy in words.        (2)

          4.2.2       Calculate the speed with which the ball strikes the wall.
                      (Ignore the mass of the cable)                                            (4)

 4.3      The engine of a motorbike exerts a force of magnitude 5 kN when the bike
          moves at a constant velocity of 72 km.h-1.
          Calculate the power delivered by the engine in the units of horsepower.               (4)
                                                                                               [22]

Copyright reserved                                                                Please turn over

### Page 10

Downloaded from hlayiso.com
10                              TECHNICAL SCIENCES P1                      (EC/SEPTEMBER 2022)

QUESTION 5 (Start on a new page.)

5.1    A steel rod is 1 m long, with a cross sectional area of 0,5 cm 2 stretches by
       0,24 cm when a force of magnitude 6 000 N is applied as shown below.

                                        1m

                                                                   6 000 N

       5.1.1   State Hooke’s Law in words.                                                 (2)

       5.1.2   Calculate the Young’s modulus of the steel rod.                             (7)

5.2    Car manufacturers use multi-grade engine oil for different working
       conditions. Consider the following three oils:

       Oil A: 10W-30
       Oil B: 20W-50
       Oil C: 15W-40

       5.2.1   Which ONE of the oils will stay THICKER at higher temperatures?             (1)

       5.2.2   What does the 10 W indicate on the label for oil A?                         (2)

5.3    A motor mechanic uses a hydraulic system to lift a car as shown in the
       diagram below. The diameter of the small piston is 40 mm while that of the
       larger piston is 160 mm. A fore of magnitude 260 N is applied vertically down
       on the smaller piston (Piston 1).

                     40 mm
                                                             160 mm

                     260 N

                     Piston 1

                                                              Piston 2

       5.3.1   State Pascal’s Law in words.                                                (2)

       5.3.2   Calculate the force exerted by the larger piston (Piston 2) on the car.     (4)

       5.3.3   State THREE applications of Pascal’s Law in our daily lives.               (3)
                                                                                         [21]

Copyright reserved                                                            Please turn over

### Page 11

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)              TECHNICAL SCIENCES P1                                              11

QUESTION 6 (Start on a new page.)

6.1    In a motor starter, parallel plate capacitor consists of two identical aluminium
       plates, each with an area 4 x 10-4 m2. The plates are separated by a distance
       of 0,06 m with air occupying the space between the plates.

       6.1.1     Define capacitance.                                                           (2)

       6.1.2     Calculate the capacitance of the parallel plates.                             (3)

       6.1.3     State TWO factors that affect the capacitance of a capacitor.                 (2)

6.2    The circuit below consist of a 6 Ω and a 5 Ω resistor connected in parallel and
       an unknown resistor R, in series as shown below.

       The switch S is closed.

                                        V1
                                        1
                                                      R

                        S                                 V2
                                             4Ω

                                             12 Ω

       The total power dissipated in the parallel part of the circuit is 50 W.
       The voltmeter across resistor R reads 8 V.

       6.2.1     Define the term power.                                                        (2)

       Calculate the:

       6.2.2     Effective resistance of the parallel combination of resistors                 (3)

       6.2.3     Resistance of resistor R                                                      (5)

       Resistor R is removed and replaced with an ammeter.

       6.2.4     How will this change affect the current through the 12 Ω resistor?

                 Choose from INCREASES, DECREASES or REMAINS THE SAME.

                 Explain your answer.                                                          (3)
       Switch S is now OPEN.
       6.2.5     What NAME is given to the reading on V1 when switch, S is open?               (1)
                                                                                              [21]

Copyright reserved                                                               Please turn over

### Page 12

Downloaded from hlayiso.com
12                               TECHNICAL SCIENCES P1                      (EC/SEPTEMBER 2022)

QUESTION 7 (Start on a new page.)

7.1    Consider a flat, square coil with 5 turns. Each of the coil’s sides is 0,50 m in
       length and has magnetic field of 0,5 T passing through it. The plane of the
       coil is perpendicular to magnetic field.

       7.1.1    Define magnetic flux.                                                      (2)

       7.1.2    Calculate the magnitude of the induced emf if the magnetic field is
                increased uniformly from 0,5 T to 1 T in 10 s.                             (6)

7.2    Shown below is a simplified diagram of an electrical device.

                                coil

                                            b

           magnet                                                        magnet

                                        a
                 X
                 B

       7.2.1    Write down the NAME of this electrical device.                             (1)

       7.2.2    State the energy conversion in the above-mentioned device.                 (2)

       7.2.3    What is the function of component B.                                       (1)

       7.2.4    Draw a diagram showing the magnetic field pattern around the
                straight section, ab of the coil due to the current flowing in the coil
                only. Indicate direction of the magnetic field lines.                      (2)
                                                                                          [14]

Copyright reserved                                                             Please turn over

### Page 13

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)            TECHNICAL SCIENCES P1                                            13

QUESTION 8 (Start on a new page.)

8.1    The diagram below shows the dispersion of white light by a prism.

       8.1.1    Define dispersion.                                                         (2)

       8.1.2    Which colour is refracted least?                                           (1)

       8.1.3    When light travels through the prism its speed decreases but its
                frequency remains constant.

                Explain why the frequency of light remains constant.                       (2)

8.2    A learner places an object 40 mm tall at a distance of 25 mm in front of a lens
       with a focal length of 40 mm.

               object

       8.2.1    Is this a DIVERGING or CONVERGING lens?                                    (1)

       8.2.2    Draw a labelled ray diagram showing the image formed.                      (7)

Copyright reserved                                                           Please turn over

### Page 14

Downloaded from hlayiso.com
14                              TECHNICAL SCIENCES P1                    (EC/SEPTEMBER 2022)

8.3    Study the images below showing the practical applications of different types
       of electromagnetic radiation.

                 X-rays                   Infra red              Radio waves

               Gamma ray               Ultra-violet rays         Microwaves

       Write down the name of electromagnetic radiation that:

       8.3.1    Has the longest wavelength                                                (1)

       8.3.2    Is used for security checks at airports                                   (1)

       The wavelength of the ultraviolet light ranges from 0,1 nm to 1 000 nm.

       8.3.3    Define the term photon.                                                   (1)

       8.3.4    Calculate the MINIMUM energy of a photon of ultraviolet light.            (4)
                                                                                         [20]

                                                                            TOTAL:       150

Copyright reserved                                                          Please turn over

### Page 15

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)               TECHNICAL SCIENCES P1                                       15

                       DATA FOR TECHNICAL SCIENCES GRADE 12
                                             PAPER 1
                 GEGEWENS VIR TEGNIESE WETENSKAPPE GRAAD 12
                                            VRAESTEL 1

TABLE 1: PHYSICAL CONSTANTS/TABEL 1: FISIESE KONSTANTES
           NAME/NAAM                    SYMBOL/SIMBOOL           VALUE/WAARDE
 Acceleration due to gravity
                                       g                     9,8 m·s-2
 Swaartekragversnelling
 Speed of light in a vacuum
                                       c                     3,0 x 108 m·s-1
 Spoed van lig in 'n vakuum
 Planck's constant
                                       h                     6,63 x 10-34 J·s
 Planck se konstante
 Electron mass
                                       me                    9,11 x 10-31 kg
 Elektronmassa
 Permittivity of free space
                                       𝜀0                    8,85 x 10-12 F.m-1
 Permittiwiteit van vrye ruimte

TABLE 2: FORMULAE/TABEL 2: FORMULES
FORCE/KRAG

 Fnet = ma                                      p = mv

 fs max = μsN                                   fk = μ k N

 Fnet Δt = Δp
                                                Fg = mg
 Δp = mv f - mv i

         L e
 MA =     =
         E l

Copyright reserved                                                         Please turn over

### Page 16

Downloaded from hlayiso.com
16                                    TECHNICAL SCIENCES P1                       (EC/SEPTEMBER 2022)

WORK, ENERGY AND POWER/ARBEID, ENERGIE EN DRYWING

 W = FΔxcosθ                                      U= mgh                or/of   EP = mgh

      1                               1           Wnet = Fnet ∆𝑥 cosθ
 K=     mv 2                   Ek =     mv 2
      2              or/of            2           K = K f − K i        or/of   Ek = Ekf − Eki

                                                       W
 Pave = Fvave    /     Pgemid = Fvgemid           P=
                                                       t
                                                  ME = Ek + Ep

ELASTICITY, VISCOSITY AND HYDRAULICS/ELASTISITEIT, VISKOSITEIT EN
HIDROULIKA

          F
 =                                                         Δ
          A                                            ε=
                                                            L

 σ                                                     F1  F
   =K                                                     = 2
 ε                                                     A1 A 2

      F
 P=                                                    P = ρgh
      A

ELECTROSTATICS / ELEKTROSTATIKA

      𝑄                                                          𝜀0 𝐴
 𝐶=𝑉                                                    𝐶=        𝑑

Copyright reserved                                                                   Please turn over

### Page 17

Downloaded from hlayiso.com
(EC/SEPTEMBER 2022)         TECHNICAL SCIENCES P1                                     17

CURRENT ELECTRICITY/STROOMELEKTRISITEIT

      V
 R=                                      emf/emk ( ε )= I(R + r)
      I
 R s = R1 + R 2 + ...

  1   1   1                              q = I∆t
    =   +   + ...
 R p R1 R 2

                                              W
 W = VQ                                  P=
                                              Δt
 W = VI  t
                                         P = VI
 W = I2R  t
                                         P = I 2R
   V 2 Δt
                                              V2
 W= R                                    P=
                                              R

ELECTROMAGNETISM/ELEKTROMAGNETISME

 ΔΦ = BA                                            ∆Φ
                                         𝜀 = −𝑁
                                                    Δ𝑡

 Vs N s
   =
 Vp Np

WAVES, SOUND AND LIGHT / GOLWE, KLANK EN LIG

 𝑣 = 𝑓𝜆                                       1
                                         𝑇=
                                              𝑓

                        c
 E = hf    or E = h
                        λ

Copyright reserved                                                 Please turn over

## Related documents

- [TECHNICAL SCIENCES P1 QP GR12 SEPT2022 English Deaf](https://www.hlayiso.com/library/technical-sciences-p1-qp-gr12-sept2022-english-deaf/f6f6becc-9762-43fb-a195-a3e9a0dd825a) — Technical Sciences · QP · 2022 · Eng
- [TECHNICAL SCIENCES P2 GR12 QP SEPT2022 English](https://www.hlayiso.com/library/technical-sciences-p2-gr12-qp-sept2022-english/2a982edd-afe6-4823-947e-7b5e056fa60f) — Technical Sciences · QP · 2022 · Eng
- [TECH SCIENCES P1 QP GR12 SEPT2023 English](https://www.hlayiso.com/library/tech-sciences-p1-qp-gr12-sept2023-english/507ed312-28c7-4819-a72c-055bb0dfebb3) — Technical Sciences · QP · 2023 · Eng
- [TECH SCIENCES P1 GR12 QP SEPT2020 English (Signing off 27 July)](https://www.hlayiso.com/library/tech-sciences-p1-gr12-qp-sept2020-english-signing-off-27-july/0f7d69d0-c47d-41a1-a835-f9e13408d8ed) — Technical Sciences · QP · 2020 · Eng
- [TECHNICAL SCIENCES P1 MEMO GR12 SEPT2022 ENG AFR](https://www.hlayiso.com/library/technical-sciences-p1-memo-gr12-sept2022-eng-afr/63e8758d-6c7e-4512-90dd-949637187c34) — Technical Sciences · Memo · 2022 · Eng
- [Technical Sciences P2 (English) 2022 QP](https://www.hlayiso.com/library/technical-sciences-p2-english-2022-qp/137b19f7-f5f9-41f8-ad5a-ae85abe49651) — Technical Sciences · QP · 2022 · Eng

## More from Grade 12 Technical Sciences

- [Grade 12 Technical Sciences P1 November 2026 Mock Memo](https://www.hlayiso.com/library/grade-12-technical-sciences-2026-nsc-november-mock-exam-memorandum-paper-1/5543b9af-5bb3-4e43-95e3-ad6028ca21e8) — Memo · 2026 · Eng
- [Gr 12 Tech Sci ATP 2023-24](https://www.hlayiso.com/library/gr-12-tech-sci-atp-2023-24/a7a03e64-2e18-4f50-a7fa-6eb1a25136c7) — ATP
- [TECH SC P1 MEMO GR12 SEPT 2025 E+A watermark](https://www.hlayiso.com/library/tech-sc-p1-memo-gr12-sept-2025-e-a-watermark/4a156330-3801-46dc-b908-43c35dc64891) — Memo · 2025
- [TECHNICAL SCIENCES P2 MG GR12 SEPT2025 watermark](https://www.hlayiso.com/library/technical-sciences-p2-mg-gr12-sept2025-watermark/717f8fcd-96bb-4848-8cb7-68903a8f0550) — Memo · 2025
- [Technical Sciences P1 Erratum June Commom Updated](https://www.hlayiso.com/library/technical-sciences-p1-erratum-june-commom-updated/c0a5373a-1bd4-4019-b849-f2a26fa7ab0b) — Errata · 2024
- [TECH SCIENCES P1 GR12 MEMO JUNE 2024 Afr+English](https://www.hlayiso.com/library/tech-sciences-p1-gr12-memo-june-2024-afr-english/7f012694-b60e-4910-b0d6-e43dd5b126e8) — Memo · 2024 · Eng

## Collection

- [Grade 12 past papers](https://www.hlayiso.com/grade-12/past-papers)

---

Hlayiso: free CAPS and IEB past papers, memos, notes and study guides for South African learners. When citing, link the page URL above, not a PDF or /api/ URL.
