Mechanical Technology PAT GRADE 10 2016 Eng

Downloaded from hlayiso.com MECHANICAL TECHNOLOGY GUIDELINES FOR PRACTICAL ASSESSMENT TASKS GRADE 10 2016 These guidelines consist of 41 pages. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 2 DBE/PAT 2016 NSC – Grade 10 TABLE OF CONTENTS Page 1. INTRODUCTION 3 2. TEACHER GUIDELINES 4 2.1 Administration of PAT 4 2.2 Assessment of PAT 4 2.3 Moderation of PAT 4 3. LEARNER GUIDELINES 5 4. GENERIC CONTENT 6–15 5. FITTING AND MACHINING – SPECIFIC CONTENT 16–20 6. AUTOMOTIVE – SPECIFIC CONTENT 21–27 7. WELDING AND METALWORK – SPECIFIC CONTENT 28–38 8. ABSENCE/NON-SUBMISSION OF TASKS 39 9. TIMEFRAMES 39 10. DECLARATION OF AUTHENTICITY 40 11. CONCLUSION 41 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 3 DBE/PAT 2016 NSC – Grade 10 1. INTRODUCTION The 16 Curriculum and Assessment Policy Statements subjects which contain a practical component all include a Practical Assessment Task (PAT). These subjects are: • AGRICULTURE: Agricultural Management Practices, Agricultural Technology • ARTS: Dance Studies, Design, Dramatic Arts, Music, Visual Arts • SCIENCES: Computer Applications Technology, Information Technology • SERVICES: Consumer Studies, Hospitality Studies, Tourism • TECHNOLOGY: Civil Technology, Electrical Technology, MECHANICAL TECHNOLOGY and Engineering Graphics and Design. A PAT allows the teacher to directly and systematically observe applied competence. The PAT comprises the application/performance of the knowledge, skills and values particular to that subject and counts 25% (i.e. 100 marks) of the total promotion/certification mark out of 400 for the subject. The PAT is implemented across the first three terms of the school year, which is broken down into different phases or a series of smaller activities that make up the PAT. Any profession requires a thorough grounding in both practice and theory of its members and Mechanical Technology is no exception. It is emphasised that the goal of the practical assessment task is not to produce a skilled craftsperson, but a Mechanical Technology learner in the broadest sense. A nation's true wealth is in its manpower and education should aim to develop the talents of the learner so that he/she can contribute to the well- being of society by using scientific and technological resources with the greatest efficiency and by continuing to develop them. To prepare a Mechanical Technology learner for one or more of these activities, his/her education should develop in him/her: • An attitude where the learner can selectively assimilate ideas, gather evidence and facts, draw logical conclusions and put them to good use creatively and with imagination • A capability to express ideas and information clearly by speech, writing, sketching or drawing • A willingness and capability to accept and exercise responsibility, to make decisions, and to learn by experience Attributes such as these cannot all be achieved in a classroom. A sound knowledge of engineering science is essential to equip the MECHANICAL TECHNOLOGY learner with the necessary practical capabilities for the required processes. There is no substitute for acquiring the feel of making things on the shop floor. Training in the art of making things is the essential bridge between trade theory and trade practice. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 4 DBE/PAT 2016 NSC – Grade 10 Practical application in the workshop must therefore be made an interesting and challenging experience, mentally and physically, with encouragement to the learner to use his/her initiative, curiosity and persistence in finding things out for himself/herself. Learning by watching should be kept to the bare minimum. Giving some degree of responsibility during practical application is very important as a stimulus and to develop self-confidence. 2. TEACHER GUIDELINES 2.1 Administration of the PAT Teachers are requested to make copies of the different phases and the assessment criteria of the PAT document. These documents must be distributed to the learners at the beginning of the year. The practical assessment task for Grade 10 is externally set and moderated, but internally assessed. Teachers must attach due dates for the different phases of the PAT (refer to the CAPS document). In this way learners may assess their progress easily. When formal assessments take place it is the responsibility of the teacher to administer assessment. The PAT (all phases) should be completed in the first three terms. The PAT should be completed under controlled conditions (refer to the Mechanical Technology CAPS Grade 10–12). 2.2 Assessment of PAT Frequent and developmental feedback is needed to guide and give support to the learner to ensure that the learner is on the right track. Both formal and informal assessment should be conducted on the different phases that constitute the PAT. Informal assessment may be conducted only to monitor progress of the phase in which the learners are engaged. Formal assessment should always be conducted by the teacher and will be recorded. 2.3 Moderation of PAT During moderation of the PAT, the phase tasks (phases 1–4), will be presented to the moderator with the assessment criteria and marks obtained. Where required the moderator should be able to call on the learner to explain the functions and principles of operation. The learner may be requested to demonstrate the skills acquired through the capability tasks for moderation purposes. On completion the moderator will, if necessary, adjust the marks of the group up or downwards depending on the decision reached as a result of moderation. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 5 DBE/PAT 2016 NSC – Grade 10 3. LEARNER GUIDELINES • The Practical Assessment Task (PAT) consists of a generic and a specialisation task in Fittings and Machining, Automotive and Welding and Metalwork. The practical work is spread over THREE terms, as set out in each of the specialisation areas. • All tasks must be completed according to the time frames set out in each of the tasks. • Learners are required to actively engage in all practical assessment tasks. • Learners who are un-cooperative will receive demerits or a zero mark allocation for that particular section of the work. • Learners who act in an unsafe manner in the workshop and endanger other learners, will be removed from the workshop and given additional corrective tasks to improve their safety awareness. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 6 DBE/PAT 2016 NSC – Grade 10 4. PRATICAL ASSESSMENT GUIDELINES – GENERIC 4.1 TOOLS: BASIC HAND TOOLS Term: 1 Start: January 2016 Completion: March 2016 Mark allocation: 20 Duration of assessment: 1 hour Learners need to identify the following tools and complete TABLE 1. TABLE 1: TOOLS QUESTION DESCRIPTION MARK 1 Name the type of tool illustrated below. a 1 b 1 c 1 d 1 e 1 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 7 DBE/PAT 2016 NSC – Grade 10 QUESTION DESCRIPTION MARK f 1 g 1 h 1 Study the spanner diagram below 2 and answer the questions that follow. What is the size of the spanner? a 1 What is the unit of the spanner? b 1 Where does the size and unit originate from? c 1 Study the tool below and answer 3 the questions that follow. What is the size of the tool? a 1 What is used it used for? b 1 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 8 DBE/PAT 2016 NSC – Grade 10 QUESTION DESCRIPTION MARK Study the spanner below 4 and answer the questions. What type of spanner is shown? a 1 What is it used for? b 1 What size is illustrated? c 1 5 Describe the spanner shown below. 2 Loosening or tightening a nut and bolt combination 6 with set of ring spanners. To which part is the main force applied? a 1 State the nature of the applied force (pulling, shearing, etc.) b 2 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 9 DBE/PAT 2016 NSC – Grade 10 QUESTION DESCRIPTION MARK What is the advantage of a ring spanner compared to a flat spanner? 7 2 8 Name the socket attachments illustrated below. a 1 b 1 c 1 d 1 e 1 Briefly explain the difference between a ½ inch and a ¼ inch drive type. 9 2 TOTAL 30 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 10 DBE/PAT 2016 NSC – Grade 10 4.2 JOINING METHODS Term: 2 Start: April 2016 Completion: June 2016 Mark allocation: 50 Duration of assessment: 3 hours Use marking-off instruments to mark off 2 plates (at least 5 mm thick) with 5 holes. FIGURE 4.1: JOINING METHODS MATERIAL: ITEM NO. DESCRIPTION MATERIAL SIZE QUANTITY 1 Marking-off plate Mild steel 75 x 75 x 5 2 Processes: Marking off plate and drilling • File off sharp edges on mild steel plate • Cut corners off away from marked-off line • File metal until accuracy is obtained • Drill and tap the centre hole with a M6 x 1,0 tap (Drill a Ø 5 mm hole) • Drill a Ø 6 mm hole in each of the plates and positions • Use a M6 x 1,0 bolt and join the plates together Marking Rubric: Plate Process Mark allocation 1. Cut and square off 5 2. File to correct size 10 3. Mark off holes 15 4. Drill each hole 5 5. Tap the centre hole 5 6. Join the two plates 5 7. Correct use of tools 3 8. Safety precautions followed 2 TOTAL 50 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 11 DBE/PAT 2016 NSC – Grade 10 4.3 FORCES Term: 2 Start: April 2016 Completion date: June 2016 Mark allocation: 30 Duration of assessment: 1 hour 4.3.1 Study the vector diagram below relating to the parallelogram of forces and determine graphically the resultant and equilibrant forces. FIGURE 4.2: FORCES Draw a force diagram using a scale of 10 mm = 1 N (10) Resultant = __________________________________________ (5) Equilibrant = _________________________________________ (5) Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 12 DBE/PAT 2016 NSC – Grade 10 4.3.2 Calculate the load on the right-hand side of the beam. (5) FIGURE 4.3: MOMENTS 4.3.3 Calculate the size of the compressive stress on the part, as shown in the diagram below. (5) FIGURE 4.4: STRESS Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 13 DBE/PAT 2016 NSC – Grade 10 4.4 MAINTENANCE Term: 2 Start: April 2016 Completion: June 2016 Mark allocation: 5 Duration of assessment: ½ hour Analyse and predict what could happen if the centre lathe, which is used daily in the workshop, is not regularly maintained? (5) Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 14 DBE/PAT 2016 NSC – Grade 10 4.5 MATERIALS Term: 3 Start: July 2016 Completion: September 2016 Mark allocation: 20 Duration of assessment: ½ hour 4.5.1 Name any FIVE non-ferrous metals used in mechanical engineering and state ONE use on each. (10) 4.5.2 State any FIVE non-ferrous alloys used in mechanical engineering and state ONE use on each. (10) Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 15 DBE/PAT 2016 NSC – Grade 10 4.6 ENGINES Term: 4 Start: September 2016 Completion: November 2016 Mark allocation: 10 Duration of assessment: ½ hour The diagram below shows the position of a piston of an internal combustion engine. Describe the operating principles of the 2- and 4-stroke internal combustion spark ignition engines and label the parts shown in the diagram. (10) FIGURE 4.5: ENGINE A B C D Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 16 DBE/PAT 2016 NSC – Grade 10 5. PRACTICAL ASSESSMENT GUIDELINES – SPECIFIC 5.1 FITTING AND MACHINING – TERMINOLOGY CANDLE HOLDER – BASE PLATE Term: 1–4 Start: January 2016 Completion: November 2016 Mark allocation: 70 Duration of assessment: 12 hours WORKING DRAWING: FIGURE 5.1: BASE PLATE ITEM DESCRIPTION MATERIAL SIZE QUANTITY NO. Candle holder 1 Mild steel 100 x 100 x 6 mm 1 base Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 17 DBE/PAT 2016 NSC – Grade 10 Preparation of the candle holder base: • File off sharp edges on mild steel plate. • Mark off hexagon. • Cut off excess material. NOTE: Leave sufficient material for filing. • File work piece to size as per sketch. • Stamp NAME and YEAR on work piece. • Remove all sharp edges. • Drill Ø 5 mm holes and tap the 6 holes M6, as per illustration. • Drill centre hole Ø 5 mm, as per illustration. • Countersink hole on one side of the plate ONLY. • Prime and paint base plate. Marking Rubric: Base plate for candle holder Process Mark allocation File off sharp edges on mild steel plate. 5 Mark-off hexagon. 15 Cut off excess material. NOTE: Leave sufficient material 5 for filing. File work piece to size as per sketch. 10 Stamp NAME and YEAR on work piece. 5 Remove all sharp edges. 5 Drill and tap 6 holes M6 as per illustration. 10 Drill centre hole Ø 6.5 mm as per illustration. 5 Countersink hole on one side ONLY. 5 Prime and paint base plate. 5 Correct use of tools. 5 Safety 5 TOTAL 70 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 18 DBE/PAT 2016 NSC – Grade 10 CANDLE HOLDER – TURNING Term: 1–4 Start: January 2016 Completion: November 2016 Mark allocation: 100 Duration of assessment: 12 hours ITEM NO. DESCRIPTION MATERIAL SIZE QUANTITY 2 Candle holder Aluminium Ø 50 x 85 1 FIGURE 5.2: CANDLE HOLDER Candle Holder: Processes Step 1: Set-up work piece and facing tool in centre lathe. Step 2: Face both ends to length (as per working drawing). Step 3: Centre drill both ends. Step 4: Drill both ends as per working drawing. Step 5: Tap hole as per working drawing. Step 6: Set cutting tool to centre height. Step 7: Turn work piece according to specifications Step 8: Calculate included angle to cut taper. Step 9: Set compound slide. Step 10: Cut taper. Step 11: Polish work piece Step 12: Assemble parts. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 19 DBE/PAT 2016 NSC – Grade 10 Process Mark allocation 1. Set-up work piece and facing tool in centre lathe. 5 2. Face both ends to length. 10 3. Centre drill both ends. 5 4. Drill both ends. 10 5. Tap hole. 5 6. Set cutting tool to centre height. 5 7. Turn work piece. 15 8. Calculate included angle to cut taper. 10 9. Set compound slide. 10 10. Cut taper. 15 11. Polish work piece . 5 12. Assemble parts. 5 TOTAL 100 Rubric for Fitting and Machining: TURNING FILING DIAMETER LENGTH Measured at 6 places TOLERANCE + 0,03 + 0,09 + 0,09 – 0,03 – 0,09 – 0,09 7 0,05 = 100% 0,10 = 100% 0,10 = 100% 6 0,10 = 80% 0,20 = 80% 0,20 = 80% 5 0,15 = 70% 0,30 = 70% 0,30 = 70% DEVIATION 4 0,20 = 60% 0,40 = 60% 0,40 = 60% 3 0,25 = 40% 0,50 = 40% 0,50 = 40% 2 0,30 = 20% 0,60 = 20% 0,60 = 20% 1 0,35 = 0% 0,70 = 0% 0,70 = 0% Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 20 DBE/PAT 2016 NSC – Grade 10 5.2 FITTING AND MACHINING – SYSTEMS AND CONTROL Term: 1–4 Start: July 2016 Completion: November 2016 Mark allocation: 15 Duration of assessment: 1 hour 5.2.1 You are required to design a gear system which has a 20 tooth gear that rotates at 240 r/min. This gear must drive another gear with 120 teeth. Calculate the rotational frequency of the driven gear. (5) FIGURE 5.3: GEARS 5.2.2 A shaft rotating at 780 r/min has a 250 mm diameter pulley which drives a second shaft with a diameter of 130 mm by means of a driving belt. In order for this to operate at a factory, the driven shaft must rotate at 1 800 r/min. (i) Determine, by means of calculations, whether the system will work. If not, what is a possible solution to ensure the proper drive? (5) (ii) Determine the belt speed in the system. (5) Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 21 DBE/PAT 2016 NSC – Grade 10 6. PRACTICAL ASSESSMENT GUIDELINES – SPECIFIC 6.1 AUTOMOTIVE – TERMINOLOGY Term: 3 Start: July 2016 Completion: November 2016 Mark allocation: 100 Duration of assessment: 10 hours REMOVING AND INSTALLING BRAKE PADS TOOLS TO BE USED: ratchet; breaker bar; assorted extensions; assorted sockets; assorted open-ended wrenches; G-clamp; hydraulic jack; jack stands; rubber mallet; wire brush; gloves DISC BRAKE LAYOUT: FIGURE 6.1: DISC BRAKE LAYOUT Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 22 DBE/PAT 2016 NSC – Grade 10 TYPES OF BRAKE CALLIPERS: FIGURE 6.2: FIXED DUAL-PISTON BRAKE CALLIPER FIGURE 6.3: FLOATING BRAKE CALLIPER Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 23 DBE/PAT 2016 NSC – Grade 10 COMPONENTS REQUIRED: • Disc brake wheel assembly • Brake pads • Brake fluid • Hand tools PROCESS: CHANGE BRAKE PADS • Step 1: Acquire brake pads. • Step 2: Loosen wheel nuts or studs on wheel. • Step 3: Raise car. • Step 4: Remove the wheel from the vehicle adhering to all necessary safety aspects. Loosen calliper. Check the brake disc for heavy rust, scoring, cracks and uneven wear. • Step 5: Unbolt and remove calliper carrier. • Step 6: Place the calliper properly; do not allow it to hang on the brake hose. • Step 7: Gently push back the piston to free the disc pads. Check the disc pad for wear. (Friction surface is still thick enough). • Step 8: Compress the piston in the calliper. • Step 9: Fit new disc pads. • Step 10: Replace parts that were removed; repeat for all the wheels. • Step 11: Bleed brakes to remove any air in the system. • Step 12: Break in pads and braking system. SPECIFICATION: REMOVE AND INSTALL BRAKE PADS STEPS METHOD Ceramic tends to be the best, as they give the best brake feel and the longest Acquire brake pads protection against brake fade, although dust may accumulate on your wheel. Remember, you are loosening, NOT removing. Get the lugs loose enough that Loosen nuts or studs you'll be able to take them off with a regular ratchet. Release the parking brake on wheels when the wheel is off. Put the hydraulic jack underneath the frame rail or the factory jacking points of Raise car the car. Place jack stands underneath the car making sure that the weight cannot shift. Now remove the wheels. Remove calliper Remove the two 17 mm or 19 mm bolts on the rear of the hub that keep the carrier calliper carrier on. These are tight so use a breaker bar with a mallet if you can. Assemble calliper Replace the carrier bolts and tighten them using an impact gun or breaker bar. carrier Using the G-clamp and one of the old brake pads, compress the calliper piston Compress calliper until the piston is flush with the housing of the calliper. Make sure that the cap is not on the brake reservoir, as you do not want to risk blowing a line. Install pads in the carrier and use a little bit of anti-squeal grease on the outside Install pads and of the pad to ensure smooth operation. Install the calliper bolts and ensure that calliper the calliper moves without binding. Tighten the bolts and double check your work Tighten the lugs hand tight when in the air, and torque them down when the Put on wheels. wheels are on the ground using a torque wrench or breaker bar. Repeat for all 4 wheels Bleed the brakes You should feel pressure within THREE pumps of the pedal. The brakes may squeal or make some noise during the first few kilometres. This Break in pads and is normal. To break in the new components accelerate to 60 km/h and gradually braking system slow to 40 km/h, and repeat a few times, then 50–30 km/h a few times. After that simply drive normally. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 24 DBE/PAT 2016 NSC – Grade 10 MARK ALLOCATION: CHANGING BRAKE PADS PROCESS MARK ALLOCATION Step 1: Acquire brake pads. 5 Step 2: Loosen wheel nuts or studs on wheel. 15 Step 3: Raise car. 5 Step 4: Remove the wheel from the vehicle adhering to all 15 necessary safety aspects. Loosen calliper. Check the brake disc for heavy rust, scoring, cracks and uneven wear. Step 5: Unbolt and remove calliper carrier. 5 Step 6: Place the calliper properly; do not allow it to hang on the 5 brake hose. Step 7: Gently push back the piston to free the disc pads. Check 15 the disc pad for wear. (Friction surface is still thick enough). Step 8: Compress the piston in the calliper. 5 Step 9: Fit new disc pads. 5 Step 10: Replace parts that were removed; repeat for all the 15 wheels. Step 11: Bleed brakes to remove any air in the system. 5 Step 12: Break in pads and braking system. 5 TOTAL 100 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 25 DBE/PAT 2016 NSC – Grade 10 6.2 AUTOMOTIVE – TERMINOLOGY HOW TO PERFORM A RADIATOR TEST Term: 3 Start: July 2016 Completion: November 2016 Mark allocation: 50 Duration of assessment: 6 hours (2 x 3 hours for each test) BACKGROUND When the engine temperature of your car rises, as evident by the temperature gauge in the console, a radiator test should be performed. External coolant leaks are relatively easy to spot, but internal leaks are a different story altogether. An overheating engine could be caused by many factors, such as low coolant levels due to leaks, faulty thermostats or a blown head gasket. External Coolant Leaks Check the engine bay for any leaks that may resemble the colour of your engine coolant. Most leaks stem from cracked radiator hoses due to old age or faulty installation. Replace the hoses if necessary. Remember that a hot engine will produce an extremely hot coolant in the radiator. Blown Head Gasket White smoke emitted from the tailpipe, brownish coolant in the reservoir, a change in colour of the engine oil or a rise in level of oil could mean a head gasket failure or a faulty engine cooling system. This can be diagnosed by a radiator test or coolant pressure test. Radiator Pressure Test A cooling system pressure tester is used to perform this test and is installed in place of the radiator cap. Take precaution when removing the radiator cap on a hot engine, because the pressure build-up could cause serious burns and scalds. Procedure 1: 1. Install the pressure gauge and pump 69 kPa of pressure. 2. Check for leaks on external surfaces when the gauge indicates a loss of pressure. 3. Check the radiator hoses, water pump and the heater core. These are the common trouble spots susceptible to leaks. 4. Turn on the heater fans and observe the air coming out of the vents. A sweet smell indicates a leak on the heater cores. 5. Continue pressure testing until the cooling system holds pressure. Procedure 2: 1. Start with a cold engine. Remove the radiator cap and install the pressure tester. 2. Start the engine with zero pressure on the gauge. 3. Observe the pressure build-up on the gauge. A properly operating cooling system will normally indicate 48 kPa to 55 kPa of pressure on the gauge. 4. If the gauge indicates a rise of 103 kPa or more of pressure, then an internal leak is evident on one of the cylinders. This is due to a faulty head gasket. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 26 DBE/PAT 2016 NSC – Grade 10 Marking rubric for procedure 1: STEPS MARKS 1. Install the pressure gauge and pump 69 kPa of pressure. 10 2. Check for leaks on external surfaces when the gauge indicates 10 a loss of pressure. 3. Check the radiator hoses, water pump and the heater core. 10 These are the common trouble spots susceptible to leaks. 4. Turn on the heater fans and observe the air coming out of the 10 vents. A sweet smell will indicate a leak on the heater cores. 5. Continue pressure testing until the cooling system holds 10 pressure. TOTAL 50 Marking rubric for procedure 2: STEPS MARKS 1. Start with a cold engine. Remove the radiator cap and install the 10 pressure tester. 2. Start the engine with zero pressure on the gauge. 10 3. Observe the pressure build-up on the gauge. A properly operating cooling system will normally indicate 48 kPa to 55 kPa 15 of pressure on the gauge. 4. If the gauge indicates a rise of 103 kPa or more of pressure, then an internal leak is evident on one of the cylinders. This is 15 due to a faulty head gasket. TOTAL 50 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 27 DBE/PAT 2016 NSC – Grade 10 6.3 AUTOMOTIVE – ENGINES Term: 1 Start: January 2016 Completion: March 2016 Mark allocation: 30 Duration of assessment: 4 hours FIGURE 6.4: ENGINE COMPONENTS Label and give the functions of the components of an engine. Procedure: 1. Cut out different numbers from a piece of paper. Use A5 paper. 2. Paste the numbers on an engine. 3. Give the learners a worksheet to complete. 4. Explain the purpose of each of the components. PART FUNCTION MARKS Distributor 3 Cylinder head 3 Intake manifold 3 Camshaft pulley 3 Water pump 3 Timing belt pulley 3 Oil pan 3 Drain bolt 3 Engine block 3 Exhaust manifold 3 TOTAL 30 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 28 DBE/PAT 2016 NSC – Grade 10 7. WELDING AND METALWORK– TERMINOLOGY 7.1 T-PIECE Term: 1–4 Start: January 2016 Completion: November 2016 Mark allocation: 65 Duration of assessment: 12 hours DESCRIPTION T-pieces are widely used throughout the mining industry where branches have to be taken from main columns for water or air supply. FIGURE 7.1 shows a typical T-piece with main and branch pipes that are equal in size. FIGURE 7.1: T-PIECE ITEM NO. DESCRIPTION MATERIAL SIZE QUANTITY Mild steel 1. Branch pipe 120 x 60 x 1,6 1 (1,6 mm)/cardboard Mild steel 2. Main pipe 240 x 120 x 1,6 1 (1,6 mm)/cardboard Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 29 DBE/PAT 2016 NSC – Grade 10 DEVELOP AND MANUFACTURE A T-PIECE WITH MAIN AND BRANCH PIPES THAT ARE EQUAL IN SIZE Use the drawing below to develop and manufacture a T-piece with main and branch pipes that are equal in size. FIGURE 7.2: T-PIECE The following standards must be achieved: 1. All of the layout angles must be within ±1° of the required angles. 2. All the layout sizes must be within ± 1,0 mm of the required measurements. 3. All the measurements of the manufactured pipes must be within ± 1,5 mm of the required sizes. 4. All the angles of the manufactured pipes must be within ± 1,5° of the required angles. 5. There must be no damage to tools and equipment. 6. All the relevant safety procedures must be adhered to. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 30 DBE/PAT 2016 NSC – Grade 10 FIGURE 7.3 shows the complete drawing of a T-piece comprising the front elevation showing the geometry to develop the patterns for the branch pipe and the hole in the main pipe. FIGURE 7.3: DEVELOPMENT OF T-PIECE Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 31 DBE/PAT 2016 NSC – Grade 10 METHOD OR PROCEDURE – DEVELOPMENT OF THE BRANCH PIPE • Draw the front elevation to size – FIGURE 7.4. • Draw a half circle with a radius equal to half the diameter of the pipe, and divide it into six equal parts. Number these parts as shown. • Project perpendicular lines downward from these points to cut the joint line. • When the pipes have equal diameters the joint lines will appear as straight lines. FIGURE 7.4: DEVELOPMENT OF BRANCH PIPE PROCEDURE Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 32 DBE/PAT 2016 NSC – Grade 10 • Calculate the circumference of the pipe, using the outside diameter (OD) of the pipe: Circumference = π x OD. The outside diameter is used to make a template from which all lines and points will be transferred onto the pipe. • Draw a line equal to the circumference of the pipe. Divide this line into 12 equal parts and number them as shown in FIGURE 7.4. • Draw perpendicular lines on these points • Use dividers and transfer the lengths of the lines numbered 1 to 7. • NOTE: Remember to measure from the end of the pipe and NOT from the half circle. • Use a flexi-curve to join these points to complete the layout of the branch pipe. DEVELOPMENT OF THE MAIN PIPE FIGURE 7.5: DEVELOPMENT OF MAIN PIPE PROCEDURE Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 33 DBE/PAT 2016 NSC – Grade 10 MANUFACTURING THE T-PIECE • Draw the two patterns on the correct thickness steel plate and use a prick punch to mark the cutting lines. • Cut out all the patterns using oxy-acetylene equipment. • Roll the two pipes. NOTE: Remember to use the mean diameter to determine the circumference of the pipe to make provision for the thickness of the material, i.e. circumference = π x MD, where MD = inside diameter of the pipe + thickness of the material. NOTE: Roll both pipes before cutting the hole in the main pipe. • Use an arc welder and tack-weld the pipe joints. • Tack-weld the two pipes together and check for squareness. • Check all sizes and make the necessary adjustments if necessary. • Complete the welding of the T-piece. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 34 DBE/PAT 2016 NSC – Grade 10 SUBJECT: MECHANICAL TECHNOLOGY SCHOOL: YEAR: 2016 TEACHER: GR: 10 NUMBER OF LEARNERS: DATE STARTED: DATE COMPLETED: PROJECT: PIPE T-PIECE WITH MAIN AND PAGE: OF BRANCH PIPES THAT ARE EQUAL IN SIZE NAMES OF LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 All layout angles are within ± 1° of the required 10 angles. All layout sizes are within ± 1,0 mm of the required 10 measurements. All measurements of the manufactured pipes are within ± 1,5° mm of the 20 required sizes. All the angles of the manufactured pipes are within ± 1,5 those 10 required. There is no damage to the tools or equipment. 10 Four clear centre lines appear on the completed 5 job. TOTAL 65 SIGNATURE OF TEACHER: SIGNATURE OF HEAD OF DEPARTMENT: SIGNATURE OF PRINCIPAL: SIGNATURE OF MODERATOR: Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 35 DBE/PAT 2016 NSC – Grade 10 7.2 WELDING – POT PLANT STAND/WALL BRACKET Term: 1–4 Start: January 2016 Completion: July/August 2016 Mark allocation: 100 Duration of assessment: 12 hours DESCRIPTION Pot plant stands are used in many homes to support flower pots. FIGURES 7.6 and 7.7 show the working drawing in first-angle orthographic projection and the isometric view of the product. MATERIAL LIST AND SPECIFICATIONS ITEM NO. DESCRIPTION MATERIAL SIZE QUANTITY 1. Frame Angle iron 30 x 30 x 5 4 off 2. Base Mild steel plate 300 x 300 x 5 1 off 3. Wall bracket Angle iron 200 x 5 2 off 4 Brace Angle iron 300 x 5 2 off The following specifications are applicable: • All layout angles must be within ±1° of the required angles. • All layout sizes must be within ± 1,0 mm of the required measurements. • All the measurements of the manufactured pot plant stand must be within ± 1,5 mm of the required sizes. • All the angles of the manufactured pot plant stand must be within ± 1,5° of the required angles. • There must be no damage to tools and equipment. • All the relevant safety procedures must be adhered to. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 36 DBE/PAT 2016 NSC – Grade 10 FIGURE 7.6: EXPLODED VIEW OF THE POT PLANT STAND FIGURE 7.7: ISOMETRIC VIEW OF THE POT PLANT STAND Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 37 DBE/PAT 2016 NSC – Grade 10 METHOD OR PROCESS OUTLINE UPPER FRAME • Mark off angle iron, four pieces of 300 mm. • Bevel the ends at an angle of 45° at 300 mm marks. • Bend at the bevelled marks so that pieces are at 90° to each other. • Weld the bent pieces together to complete the frame. WALL BRACKET • Mark off and cut two pieces of angle iron 200 mm in length. BRACES • Mark off and cut two pieces of 300 mm angle iron. FRAME TOP PLATE • Mark off and cut one piece of 300 x 300 x 5 mild steel plate according to size. ASSEMBLY • Weld frame to wall bracket, braces and frame top plate, as shown on the working drawing. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 38 DBE/PAT 2016 NSC – Grade 10 SUBJECT: MECHANICAL TECHNOLOGY SCHOOL: YEAR: 2016 TEACHER: GR: 10 NUMBER OF LEARNERS: DATE STARTED: DATE COMPLETED: PROJECT: POT PLANT STAND PAGE: OF NAMES OF LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 All layout angles are within ±1° of the required 15 angles. All layout sizes are within ± 1,0 mm of the 25 required measurements. All the measurements of the manufactured pot plant stand are within 25 ± 1,5 mm of the required sizes. All the layout angles of the manufactured pot plant stand are within 25 ± 1,5° of the required angles. There is no damage to tools and equipment. 10 TOTAL 100 SIGNATURE OF TEACHER: SIGNATURE OF HEAD OF DEPARTMENT: SIGNATURE OF PRINCIPAL: SIGNATURE OF MODERATOR: Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 39 DBE/PAT 2016 NSC – Grade 10 8. ABSENCE/NON SUBMISSION OF TASKS. If a learner's practical assessment task is incomplete or unavailable for a valid reason, the learner will be given three weeks before the commencement of the final end-of-year examinations to submit the outstanding task. Should a learner fail to fulfil the outstanding PAT requirement such a learner will be awarded a zero (0) for that PAT component. A learner's results are regarded as incomplete if he/she does not offer any component of the PAT task. He/She will be given another opportunity based on the decision of the Head of the Assessment Body. Should the learner fail to fulfil the outstanding PAT requirement, the marks for these components will be omitted and the final mark for Mechanical Technology will be adjusted for promotion purposes in terms of the completed tasks. 9. TIME FRAMES 9.1 GENERIC January–March Basic hand tools Joining methods April–June Forces Maintenance July–September Materials September–November Engines 9.2 SPECIFIC – FITTING AND MACHINING Terminology – Base January–November Terminology – Candle holder July–November Systems and Control 9.3 SPECIFIC – AUTOMOTIVE January–March Engines Terminology – Brakes July–November Terminology – Radiator 9.4 SPECIFIC – WELDING AND METALWORK Terminology – Development January–November Terminology – Pot Plant stand Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 40 DBE/PAT 2016 NSC – Grade 10 10. DECLARATION OF AUTHENTICITY NAME OF THE SCHOOL: ……………………………………………………….. NAME OF LEARNER: …………………………………………..………………... (FULL NAME(S) AND SURNAME) EXAMINATION NUMBER: ……….………………………………………………. NAME OF TEACHER: ……………………………………………………………. SCHOOL STAMP I hereby declare that the project submitted for assessment is my own, original work and has not been previously submitted for moderation. ___________________________________ ____________ SIGNATURE OF CANDIDATE DATE As far as I know, the above declaration by the candidate is true and I accept that the work offered is his or her own. ___________________________________ ____________ SIGNATURE OF TEACHER DATE Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology 41 DBE/PAT 2016 NSC – Grade 10 11. CONCLUSION On completion of the practical assessment task, learners should be able to demonstrate their understanding of the industry, enhance their knowledge, skills, values and reasoning abilities as well as establish connections to life outside the classroom and address real world challenges. The PAT furthermore develops learner's life skills and provides opportunities for learners to engage in their own learning. Copyright reserved