Skip to content

Mechanical Technology Grade 12 Gauteng June 2025 Memo (Eng)

MemorandumMechanical TechnologyGrade 12202518 pages

Grade 12 Mechanical Technology memorandum from the Gauteng June Exam 2025 (English), 18 pages. Read online or download the free PDF.

Free to read online, no sign-up needed

Loading document…

Loading document…

Gauteng June Exam 2025

Document textSearch extracted text and jump to a page.
JUNE EXAMINATION GRADE 12 2025 MARKING GUIDELINES MECHANICAL TECHNOLOGY: WELDING AND METALWORK 18 pages
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 1. Welding and Metalwork Marking Guideline instructions: 1.1 During marking of multiple choice questions, only ONE possible answer can be accepted. If the candidate indicated two or more responses, ONLY the first response will be recognised and marked according to marking guideline. 1.2 Where the number of responses of the candidate exceeds the required number stated in the question, only the first number of responses will be accepted. E.g if the question states ‘Name THREE …’ and the candidate stated four different responses, ONLY the first three will be accepted and recognised. 1.3 If question numbering of sub-question is not correct according to question paper sequence, the responses can be accepted if a sequence pattern can be identified. 1.4 Attention must be given to mark allocation in questions marks were allocated to one response for e.g (Any 1 x 2). 1.5 There must be ONE tick allocated for each mark awarded. 1.6 An unanswered question must be indicated with wrong tick mark. 1.7 All blank pages in booklet/answer sheet must be crossed out to indicate recognition that pages have been seen by the marker. 1.8 Attention must be given to questions where candidates did not complete the question and continue answering further in the booklet/answer sheet. Such questions must be continued marking and marks awarded if awarded. 1.9 During calculation marking, pay attention to where the position of the tick mark is. 1.10 If a candidate skipped a step where a tick mark is allocated in the marking guideline and the final answer is correct, the total amount of tick marks must be indicated by the marker to indicate full marks awarded for question correctly answered so that the examination assistants can verify marks awarded. 1.11 If the unit required for calculations is specified in the question, the final answer can be considered correct without explicitly stating the unit, provided that the numerical value matches the unit specified or used in the question. 2
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 1.12 If an incorrect unit is stated in the candidate answer during calculations, the answer will be wrong even if the value itself is correct. 1.13 Attention during calculation must be given as to different methods of obtaining correct answer. 1.14 Pay attention must be given to special marking instructions to the marker stated in the marking guideline. 1.15 A red line must be drawn by the marker to indicate the end of each question. 1.16 Sub-question total marks must be allocated on the outside margins of the booklet pages and NOT on the inside margins. 1.17 Sub-question total marks allocated on the outside margins in line with the sub-question and NOT circled. 1.18 Total of question must be indicated on the red line drawn by the marker and circled as to indicate marks for particular question. 1.19 Marker must transfer total marks to cover page/first page, sign and date the answer sheet to verify correctness of transfer of marks to working mark sheets. 3
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC) 1.1 A (1) 1.2 D (1) 1.3 B (1) 1.4 C (1) 1.5 D (1) 1.6 C (1) [6] 4
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 2 SAFETY (GENERIC) 2.1 First aid stages: • Examination ✓ • Diagnosis ✓ • Treatment ✓ (3) 2.2 Pressure gauge: • To make sure there are no leakages. ✓ • To make sure that the readings are accurate. ✓ (Any 2 x 1) (2) 2.3 Safety boots: • To protect one’s feet from falling objects or objects on the floor.  • To protect one’s feet from sparks/ hot work.  (1) 2.4 Before turning on an angle grinder: • Make sure that there are no cracks or chips on the grinding disc.  • Safety guard must be in place.  • PPE must be worn.  • Beware of lockable switches in the on position when the machine is plugged in and switched on.  • Check for defective cables.  • Secure workpiece properly. Grinding angle to be away from body to prevent sparks falling directly onto clothing.  • Check that the correct disk is fitted correctly for the work to be done.  (Any 2 x 1) (2) 2.5 Power saw safety precautions AFTER operation: • Switch off the machine. ✓ (1) 5
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 2.6 Safety when operating gas welding equipment: • Always store, transport, and use oxygen and acetylene cylinders in an upright position.  • Prevent oil and grease from coming into contact with oxygen cylinders, valves, regulators, fittings, and gauges.  • Stand to the side (not in front) of the cylinder nozzles when opening the valves.  • Ensure that you open the gas valves very slowly, and never open the acetylene valve more than half a turn.  • Always leave the acetylene cylinder's spindle key in place so that the valve can be closed quickly in case of an emergency.  • Hoist cylinders in a net or crate. • Never let cylinders fall from heights. • Do not work with open flames near the cylinders.  • Do not strike the cylinders with a hamer.  • Do not use cylinders as rollers.  (Any 3 x 1) (3) 2.7 Drilling small pieces on a pedestal drill: • Clamp the workpiece securely to the table . • Do not hold it by hand if it slips from the clamp.  (Any 2 x 1) (2) 2.8 Responsibility of the employer regarding health and safety: • Ensure sufficient lighting  • Ensure sufficient ventilation • Provide first-aid equipment • Provide a safe/clean working environment • Provide personal protective equipment (PPE)  • Provide safety training to employees (Any 1 x 1) (1) 2.9 Workshop layout: 2.9.1 Product layout. ✓ (1) 2.9.2 Disadvantages of product layouts: • Lack of flexibility ✓ • Optimum use of equipment is not possible ✓ (Any 2 x 1) (2) [18] 6
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 3: MATERIALS (GENERIC) 3.1 Conducting the following tests: 3.1.1 Machining test: Cut two unknown samples identical in appearance and size in a machine tool, using the same speed and feed for both. Compare to known samples of materials. (2) 3.1.2 Sound test: • Drop the metal on the floor  or hit the metal with a hammer.  • Compare the sound it makes  to known samples.  (Any 1 x 2) (2) 3.2 Property tested with a bend test: Ductility  (1) 3.3 Heat treatment factors: • Workpiece size  • Quenching rate  • Carbon content  (3) 3.4 3.4.1 Case hardening: To produce a hard case over a tough core. (2) 3.4.2 Normalising: Relieve internal stresses produced by machining, forging and welding.  (2) 3.5 Rapid cooling / quenching medium: • Water • Brine (salted water) • Oil (Any 2 x 1) (2) [14] 7
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC) 4.1 B (1) 4.2 C (1) 4.3 B (1) 4.4 B (1) 4.5 C (1) 4.6 B (1) 4.7 D (1) 4.8 B (1) 4.9 B (1) 4.10 B (1) 4.11 C (1) 4.12 D (1) 4.13 A (1) 4.14 C (1) [14] 8
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 5: TERMINOLOGY (TEMPLATES) (SPECIFIC) 5.1 Definitions 5.1.1 Template loft: • It is the heart of a structural workshop.  • It is a place where more complicated parts of the steel are laid out on the floor in full sizes.  (Any 1 x 2) (2) 5.1.2 Plate girders: It is a combination of plates and angle iron welded together.  (2) 5.2 Advantages of templates: • Quicker to use to improve mass production.  • Accurate production. • Cheap to manufacture. • Unskilled labour will be able to use it. • Avoid unnecessary wastages/cost effective. • Uniformity in production.  • Can be reused.  (Any 3 x 1) (3) 5.3 Supplementary symbols: The purpose of supplementary symbols is to provide extra information regarding a welded joint. ✓ (1) 5.4 Elements of the welding symbols: A – Weld on-site  B – Weld size C – Weld symbol  D – Length of weld  E – Pitch of weld  F – Tail/Weld method is MIG welding  (6) 9
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 5.5 Mean diameter and mean circumference calculation: 5.5.1 Mean diameter = Internal diameter + Plate thickness  = 660 mm + 35 mm  = 695 mm  (3) 5.5.2 Mean Circumference = π x mean diameter  = π x 695 mm  = 2 183,41 mm  = 2 183 mm  (4) s 5.5.3 Mean diameter Outside diameter Material thickness (3) 5.6 Properties of a template loft: • It is quieter.  • The lighting is better.  • All equipment is at hand.  • Wooden floors need to be clean. • It has a permanent base and centre lines on the floor. • Markings on the floor enhance accuracy.  (Any 3 x 1) (3) 5.7 A – Purlin B – Rafter  C – Incline tie/Internal bracing/strut  D – Tie beam  E – Shoe plate/Gusset plate  (5) [32] 10
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 6: TOOLS AND EQUIPMENT 6.1 6.1.1 Arc welding equipment A – Electrode  B – Electrode holder  C – Arc  D – Earth Lead/Clamp lead  E – Base/Parent metal  (5) 6.1.2 Holds the electrode  (1) 6.2 6.2.1 Arc welding machine: Arc welding uses a welding power supply to create an electric arc  between an electrode and the base metals  which generates heat to melt the metals at the welding point to fuse it together.  (3) 6.2.2 Spot/Resistance welding equipment: This method uses a heating effect which occurs when a current flows  through a resistance  to fuse two plates together.  (4) 6.2.3 Plasma cutter: Creating an electrical channel of ionised gas (plasma),  from the plasma cutter itself through the workpiece that is being cut. It forms a completed electric circuit  via a grounding clamp. Compressed air is blown toward the workpiece through a focused nozzle at high speed.  A high frequency, electrical arc is then formed within the gas between an electrode near or integrated into the gas nozzle and the workpiece itself.  (4) 6.3 Metal inert gas  (1) 6.4 Hand tool: • Chipping hammer  • Wire brush  (Any 1 x 1) (1) 6.5 Horizontal band saw • Ensures clean cuts.  • Removes shavings/cuttings.  • Blade life is prolonged.  • Cools the blade.  • Cools the metal.  (Any 2 x 1) (2) 6.6 Functional vertical rolling machine: • Rolling thick plates • Rolling large diameter workpieces. (Any 1 x 1) (1) 11
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 6.7 Oxy-acetylene equipment processes: • Gas welding  • Brazing  • Silver soldering  • Heating/Melting  • Cutting  (Any 1 x 1) (1) 6.8 Gas welding equipment: (1) 6.8.1 Oxygen regulator/Acetylene regulator/regulator 6.8.2 A Gauge  B Outlet  C Inlet  D Pressure adjusting knob  (4) 6.9 Black  (1) 6.10 To prevent  back feeding/flashback of flame  (2) [31] QUESTION 7: FORCES 7.1 300 N 100 N B A E F C D 12
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 a e d MEMBER FORCE (N) NATURE AE 140 N  STRUT  b f EF 285 N  STRUT  FC 140 N  STRUT  BF 100 N  TIE  ED 100 N  TIE  c Note to markers 7.1 and 7.2 must have a template drawn to scale to check the size of the drawings when marking the paper. Tolerance = 2 mm (9) 7.2 Beams: 7.2.1 Moment about LR: (RR  9) = (2  4) + (2  7) + (2  8) ✓ RR  9 = (8) + (14) + (16) ✓ 38 RR = 9 RR = 4,2 kN ✓ Moments about RR: (LR  9) = (4  7) + (2  2) + (2 ) ✓ LR  9 = (28) + (4) + (2) ✓ 34 RR = 9 LR = 3,8 kN ✓ (6) 7.2.2 BM by B = (3,8 × 2) – (4 × 0) = 7,6 kN.m ✓ BM by C = (3,8 × 7) – (4 x 5) – (2 x 0) = 6,6 kN.m ✓✓ BM by D = (3,8 × 8) – (4 × 6) – (2 × 1) = 4,4 kN.m ✓✓ (5) 13
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 7.2.3 Bending moment diagram: BENDING MOMENT DIAGRAM Scale (4) 7.3 Calculate the stress in the round bar: 7.3.1 Load Stress = Area  ² Area = 4 Area = 0,00000078539 m² ✓ Stress = 150 000 ✓ 0,00000078539 Stress = 190,098593 Gpa ✓ (3) 7.3.2 Calculate the strain in the round bar (answer in full decimals): Change in length Strain = Original length 0,6 ✓✓ = 6 000 = 0,001 ✓ (3) [40] 14
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 8: JOINING METHODS INSPECTION OF WELD 8.1 Welding defects: 8.1.1 Slag inclusion: • Using well-maintained consumables. ✓ • Clean the joint properly. ✓ • Slag must be removed before welding the next bead. ✓ • Too slow welding movements. ✓ • Electrodes are too big. ✓ • Wrong or too big weaving action. ✓ (Any 1 x 1) (1) 8.1.2 Centre-line cracks: • Aiming for a width-to-depth ratio of 1 : 1. ✓ • Decreasing the current to reduce excess penetration. ✓ • Decreasing welding voltage/current. ✓ • Slowing travel speed. ✓ • Reduce high carbon content in weld. ✓ • Welding while joint is under stress due to joint design, use clamping devices. ✓ (Any 1 x 1) (1) 8.2 Free bend test: 8.2.1 Purpose of test on a weld. Measures flexibility of the welding joint and heat affected zone of the welding joint. Measures the percentage extension of the weld metal. ✓ (1) 8.2.2 How the test is done: • After welding, the material is trimmed in the opposite direction of welding. ✓ • Scratch two lines of 1,6 mm on the edges of the welding bead and measure the distance. ✓ • Bend the material first 30°. ✓ • Measure the lines again and update the percentage extension. ✓ (4) 8.3 Types of flames: • Carburising ✓ • Oxidizing ✓ • Neutral ✓ (3) 15
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 8.4 Nick-break test: Make a hacksaw cut at both edges, through the centre of the weld. ✓ Place the specimen on two steel supports. ✓ Use a sledgehammer to break the specimen in the area of the cuts. ✓ Inspect the exposed weld metal in the break ✓ for incomplete fusion, slag inclusion, etc. ✓ (4) 8.5 Welding defects during arc welding: 8.5.1 Porosity: • Cleaning the welding surface. ✓ • Use dry electrodes. ✓ • Avoid rust on the electrode. ✓ • Ensure that the supply of shielding gas is not interrupted. ✓ • Avoid welding in windy conditions. ✓ • Use the correct arc length. ✓ (Any 2 x 1) (2) 8.5.2 Incomplete penetration: Set to the correct current setting. • Apply the correct electrode angle. • Increase travel speed. • Use the correct root gap. • Ensure the correct joint preparation. (Any 2 x 1) (2) [18] 16
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 QUESTION 9: STRESSES AND DISTORTION (STRESSES AND DISTORTION) (SPECIFIC) 9.1 Distortion: Tension in the welding bead due to heat and cooling of the welding bead ✓ and heat affected zone which causes deformation. ✓ (2) 9.2 9.2.1 Distortion in A: Specific steel application electrodes have other thermal properties than the parent metal ✓ which can cause deformation if pre-heating is not done. ✓✓ (3) 9.2.2 Residual stress at B: • Expulsion during heating could be opposed. ✓ • Contraction during cooling could be opposed. ✓ • Applied tension on the load could cause movement. ✓ • Applied tension could not cause movement. ✓ (Any 3 x 1) (3) 9.2.3 Methods to reduce distortion: • Do not overweld ✓ • Uninterrupted welding ✓ • Place welds near the neutral axis ✓ • Use as few runs as possible ✓ • Use Backstep-Welding ✓ • Provide shrinkage force ✓ • Plan welding sequence ✓ • Use a strongback ✓ (Any 4 x 1) (4) 9.3 Cold working on steel: • The previous amount of cold work. ✓ • The temperature and time of the annealing process. ✓ • Composition of the metal. ✓ • The melting point. ✓ (4) 9.4 When austenite is allowed to cool slowly: • The grain formation will become uniform. ✓ • Carbon content will change. ✓ • Internal structure will change. ✓ (3) 17
MECHANICAL TECHNOLOGY: WELDING MARKING GUIDELINES AND METALWORK GR12 0625 9.5 Factors: • Size ✓ • Thickness ✓ • Thermal conduction ✓ (3) 9.6 FOUR quenching media used to cool down steel: • Fused salts ✓ • Water ✓ • Air ✓ • Sand ✓ • Brine ✓ • Oil ✓ (Any 5 x 1) (5) [27] TOTAL: 200 18

Study this subject

More from Grade 12 Mechanical Technology

View all