Confidential
NATIONAL
SENIOR CERTIFICATE
GRADE 12
MECHANICAL TECHNOLOGY: AUTOMOTIVE
NOVEMBER 2024
MARKS: 200
TIME: 3 hours
This question paper consists of 17 pages and a 2-page formula sheet.
Copyright reserved Please turn over
Skip to contentAll 2024 papers %20MG%20Eng--ed5ab6d3-088f-425c-ade8-86186a031594/v1-3e0bd44f4bc86cf3bb1d/card.webp)
_Afrikaans_hlayiso.com_--aadd113c-5a3b-4f4d-a4c4-3a80cd86f882/v1-fd2ca7edf910eab03a55/card.webp)
%20GR12%20MEMO%20SEPT2024_Afrikaans_hlayiso.com_--2f874dd1-8c03-49a9-8c70-41ac528693d0/v1-55f44edf9664bf65cf74/card.webp)

_English_hlayiso.com_--2c18efa9-a7cc-42c1-a732-2ff3511c8c1c/v1-098ff39ac7fe2a71ec09/card.webp)
%20MG%20Afr--03c703c8-8125-4d5a-a124-37013b381c7a/v1-02788e8df50b92af342d/card.webp)
View all
%20MG%20Afr--552ebeca-d294-4c37-b3fb-cded79fa438f/v1-b698b76db92c8affef7e/card.webp)


%20GR12%20MEMO%20SEPT2023_English_hlayiso.com_--dfc975c1-e179-4741-8d4f-e3b20c744c7e/v1-c61c66086bf36fcf31e0/card.webp)

Mechanical Technology Grade 12 November 2024 NSC QP (Eng)
Grade 12 Mechanical Technology question paper from the November 2024 NSC (English), 19 pages. Read online or download the free PDF.
Mechanical Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 19 pages. Read online or download the PDF.
- Subject
- Mechanical Technology
- Grade
- Grade 12
- Document type
- Question paper
- Year
- 2024
- Exam period
- November 2024 NSC
- Curriculum
- CAPS
- Pages
- 19
- File size
- 851.6 KB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 19
This exam
Document textSearch extracted text and jump to a page.
Mechanical Technology: Automotive 2 DBE/November 2024
NSC Confidential
INSTRUCTIONS AND INFORMATION
1. Write your centre number and examination number in the spaces provided
on the ANSWER BOOK.
2. Read ALL the questions carefully.
3. Answer ALL the questions.
4. Number the answers correctly according to the numbering system used in
this question paper.
5. Start EACH question on a NEW page.
6. Show ALL calculations and units. Round off final answers to TWO decimal
places.
7. Candidates may use non-programmable scientific calculators and drawing
instruments.
8. The value of gravitational acceleration should be taken as 9,81 m/s2 or
10 m/s2.
9. All dimensions are in millimetres, unless stated otherwise in the question.
10. Write neatly and legibly.
11. A formula sheet is attached at the end of the question paper.
12. Use the criteria below to assist you in managing your time.
QUESTION CONTENT MARKS TIME IN MINUTES
GENERIC
1 Multiple-choice Questions 6 6
2 Safety 10 10
3 Materials 14 14
SPECIFIC
4 Multiple-choice Questions 14 10
5 Tools and Equipment 23 20
6 Engines 28 25
7 Forces 32 25
8 Maintenance 23 20
9 Systems and Control (Automatic Gearbox) 18 20
Systems and Control (Axles, Steering
10 32 30
Geometry and Electronics)
TOTAL 200 180
Copyright reserved Please turn over
Mechanical Technology: Automotive 3 DBE/November 2024
NSC Confidential
QUESTION 1: MULTIPLE-CHOICE QUESTIONS (GENERIC)
Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(1.1 to 1.6) in the ANSWER BOOK, e.g. 1.7 E. Nov
1.1 Which statement below is CORRECT in terms of a recommendation for the
application of first aid?
Do NOT …
A remove anything that is stuck to the wound.
B check the pulse of the patient.
C give attention to the loss of blood or breathing difficulties.
D check the surroundings for dangerous objects. (1)
1.2 Where more than … employees are employed at a workplace, the employer
must provide an accessible first-aid box.
A 2
B 3
C 4
D 5 (1)
1.3 What causes accidents when working with revolving machinery, such as
a bench grinder?
A Overconfidence
B Correct wheel size
C Gap between tool rest and grinding wheel not exceeding 3 mm
D Correctly rated grinding wheel for the bench grinder (1)
1.4 Which test does NOT damage a work piece?
A Spark test
B Sound test
C Bending test
D Machining test (1)
1.5 Which of the following products is case-hardened?
A Tin cans
B Machine guards
C Hand files
D Gears and cams (1)
1.6 Which process is the first step in the production of high-strength steel?
A Normalising
B Annealing
C Hardening
D Tempering (1)
[6]
Copyright reserved Please turn over
Mechanical Technology: Automotive 4 DBE/November 2024
NSC Confidential
QUESTION 2: SAFETY (GENERIC)
2.1 State TWO safety precautions that must be adhered to after the horizontal
band saw has been switched on. (2)
2.2 Name the THREE stages when basic first-aid treatment is given to help an
injured person. (3)
2.3 Why must oil or grease NOT be in contact with the oxygen fittings when
handling oxygen cylinders? (1)
2.4 State TWO disadvantages of the process workshop layout. (2)
2.5 State TWO advantages of the product workshop layout. (2)
[10]
QUESTION 3: MATERIALS (GENERIC)
3.1 State if the following materials are easy or hard to file during a filing test:
3.1.1 Cast iron (1)
3.1.2 Cast steel (1)
3.1.3 Mild steel (1)
3.2 Explain what heat treatment is. (3)
3.3 Explain what the effects will be if metal is heated too fast during the heat-
treatment process. (4)
3.4 Name the TWO types of steel best suited for case hardening. (2)
3.5 Explain the reason for tempering steel during the heat-treatment process. (2)
[14]
Copyright reserved Please turn over
Mechanical Technology: Automotive 5 DBE/November 2024
NSC Confidential
QUESTION 4: MULTIPLE-CHOICE QUESTIONS (SPECIFIC)
Various options are provided as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers
(4.1 to 4.14) in the ANSWER BOOK, e.g. 4.15 E.
4.1 An OBD scanner is used on vehicles with …
A carburettors.
B no electronic control module (ECM).
C an electronic control unit (ECU).
D contact breaker ignition systems. (1)
4.2 Which wheel alignment tool is used to measure toe-out?
A Turntable
B Dunlop gauge
C Bubble gauge
D Wheel balancer (1)
4.3 Which ONE of the following is part of the reciprocating mass in an engine?
A Camshaft
B Valves
C Pistons
D Crankshaft (1)
4.4 Which ONE of the following is the cause of crankshaft vibrations?
A Carefully balanced crank webs
B Oval crankshaft journals
C Balanced rotating mass
D Balanced reciprocating mass (1)
4.5 Torque is defined as …
A the rotational frequency of a shaft.
B a force causing linear movement.
C the rate at which work is done.
D the twisting force applied to a rotating shaft. (1)
4.6 Which method below is used to increase the compression ratio of an engine?
A Fit a thinner gasket between the cylinder block and the cylinder head
B Fit the pistons with suitable lower crowns
C Fit a thicker gasket between the cylinder block and the cylinder head
D Fit a crankshaft with a shorter stroke (1)
Copyright reserved Please turn over
Mechanical Technology: Automotive 6 DBE/November 2024
NSC Confidential
4.7 Identify the diagram shown in FIGURE 4.7 below.
FIGURE 4.7
A Planimeter
B Indicator diagram
C Carbon content equilibrium diagram
D Stress-strain diagram (1)
4.8 Which ONE of the following is a reason for a high hydrocarbon (HC) reading
on an internal combustion engine?
A Ideal air-fuel ratio
B Warm valves
C A clogged air filter
D Lean air-fuel ratio (1)
4.9 A wet compression test can be used to determine whether the cylinder has
a leak at the …
A intake valve.
B exhaust valve.
C piston rings.
D head gasket. (1)
4.10 Which of the following determines the correct gear ratio according to load
and speed in an automatic gearbox?
A Brake bands
B Hydraulic pistons
C Valve body
D Oil pump (1)
Copyright reserved Please turn over
Mechanical Technology: Automotive 7 DBE/November 2024
NSC Confidential
4.11 Which gear is selected when the planet carrier is locked on an epicyclic gear
system?
A First or low gear
B Second or intermediate gear
C Third or top gear
D Reverse gear (1)
4.12 Which of the following will cause a large positive camber angle on the wheels
of a vehicle?
A Increase the negative effects of KPI
B A negative cornering effect of the vehicle
C The wheels will stop rotating
D The tyres will wear evenly (1)
4.13 Identify the symbol shown in FIGURE 4.13 below.
FIGURE 4.13
A Regulator
B Capacitor
C Diode
D Distributor (1)
4.14 What is the function of a diesel particulate filter (DPF)?
A To clean the intake air
B To clean the particles from the fuel
C To atomise the fuel
D To convert soot into ash (1)
[14]
Copyright reserved Please turn over
Mechanical Technology: Automotive 8 DBE/November 2024
NSC Confidential
QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)
5.1 Why are the following procedures performed during a compression test?
5.1.1 The air filter is removed (1)
5.1.2 Dirt is removed from around the spark plugs before removing the
spark plugs (1)
5.1.3 Disconnect the ignition system (1)
5.1.4 Record the readings (1)
5.2 FIGURE 5.2 below shows a cylinder leakage tester. Answer the questions
that follow.
Pressure
gauge
C
A
B
FIGURE 5.2
5.2.1 Label A–C. (3)
5.2.2 What is the unit of measurement on the pressure gauge? (1)
5.2.3 What is the unit of measurement of gauge C? (1)
5.3 State FOUR safety precautions that must be observed when performing the
exhaust gas analysis. (4)
5.4 Describe TWO functions of the on-board diagnostic scanner. (2)
Copyright reserved Please turn over
Mechanical Technology: Automotive 9 DBE/November 2024
NSC Confidential
5.5 FIGURE 5.5 below shows a machine used in an automotive workshop.
Answer the questions that follow.
FIGURE 5.5
5.5.1 Identify the machine. (1)
5.5.2 State TWO functions of this machine. (2)
5.5.3 What safety device is NOT attached to this machine? (1)
5.5.4 Why should this machine be calibrated? (1)
5.6 Explain, in THREE steps, how to measure the camber angle after the bubble
gauge is fitted to the wheel. (3)
[23]
Copyright reserved Please turn over
Mechanical Technology: Automotive 10 DBE/November 2024
NSC Confidential
QUESTION 6: ENGINES (SPECIFIC)
6.1 What is the primary function of the crankshaft? (2)
6.2 Name the part that is usually attached to the nose of the crankshaft to
decrease vibrations. (1)
6.3 Why is the reciprocating mass kept as light as possible? (1)
6.4 Explain how to obtain the firing order from the valve train of an engine, after
the tappet cover has been removed. (3)
6.5 FIGURE 6.5 below shows the configuration of a four-stroke four-cylinder
engine. Answer the questions that follow.
B
A
C
FIGURE 6.5
6.5.1 Identify the type of engine configuration. (1)
6.5.2 Label A–C. (3)
6.6 Draw a neat, labelled sketch to illustrate the position of the crank pins in
a six-cylinder in-line engine. (3)
6.7 Answer the following questions with regard to turbochargers:
6.7.1 Describe THREE advantages of using a turbocharger on an
engine. (3)
6.7.2 Give TWO reasons why synthetic oil is used to lubricate
turbochargers. (2)
6.7.3 Which type of turbocharger does not have vanes? (1)
Copyright reserved Please turn over
Mechanical Technology: Automotive 11 DBE/November 2024
NSC Confidential
6.8 Explain the following terms with regard to turbochargers:
6.8.1 Boost (2)
6.8.2 Turbo lag (2)
6.9 FIGURE 6.9 below shows a supercharger. Answer the questions that follow.
B
A
C
FIGURE 6.9
6.9.1 Identify the type of supercharger. (1)
6.9.2 Label A–C. (3)
[28]
Copyright reserved Please turn over
Mechanical Technology: Automotive 12 DBE/November 2024
NSC Confidential
QUESTION 7: FORCES (SPECIFIC)
7.1 Define the following terms:
7.1.1 Clearance volume (2)
7.1.2 Compression ratio (2)
7.2 Calculate the work done if a hoist needs to raise a vehicle weighing 690 kg
to a height of 2 m. (3)
7.3 State TWO methods to lower the clearance volume on an internal
combustion engine. (2)
7.4 FIGURE 7.4 below shows a cylinder. Answer the questions that follow.
A = 79 mm
B = 83 mm TDC
CR = 9 : 1
B A
BDC
FIGURE 7.4
7.4.1 Label distances A and B. (2)
7.4.2 Calculate the swept volume in the cylinder in cm3 when
A = 79 mm and B = 83 mm. (3)
7.4.3 Calculate the clearance volume of the cylinder. (3)
7.5 The following data was recorded during a test carried out on a four-stroke
four-cylinder petrol engine:
Mean effective pressure: 1 400 kPa
Stroke: 110 mm
Bore diameter: 100 mm
Engine revolutions: 3 600 r/min
Calculate the indicated power in kW. (7)
Copyright reserved Please turn over
Mechanical Technology: Automotive 13 DBE/November 2024
NSC Confidential
7.6 The indicated power of a two-stroke engine is 50 kW at 2 000 r/min. It has
a cylinder bore diameter of 35 mm with a stroke length of 40 mm. The force
required to stop the flywheel is 50 N with a brake arm length of 350 mm.
Calculate the following:
7.6.1 Torque (3)
7.6.2 Brake power in kW (3)
7.6.3 Mechanical efficiency (2)
[32]
Copyright reserved Please turn over
Mechanical Technology: Automotive 14 DBE/November 2024
NSC Confidential
QUESTION 8: MAINTENANCE (SPECIFIC)
8.1 TABLE 8.1 below shows information regarding the results of the exhaust gas
analysis of an internal combustion engine.
Complete TABLE 8.1 by giving ONE cause and ONE appropriate corrective
measure for EACH fault. Write only the answer next to the question numbers
(8.1.1 to 8.1.4) in the ANSWER BOOK.
CORRECTIVE
FAULTS (READING) POSSIBLE CAUSES
MEASURES
High carbon monoxide
8.1.1 8.1.2
(CO) reading
Low carbon dioxide
8.1.3 8.1.4
(CO2) reading
TABLE 8.1 (4)
8.2 The readings below were taken during a compression test on a
four-cylinder internal combustion engine. Answer the questions that follow.
Cylinder 1: 9 bars
Cylinder 2: 7,1 bars
Cylinder 3: 8,7 bars
Cylinder 4: 8,9 bars
8.2.1 What is the maximum variation allowed, in percentage (%),
between the compression readings? (1)
8.2.2 State ONE possible cause and its corrective measure for the low
reading in cylinder 2. (2)
8.3 Identify FOUR locations where leakages can be detected during a cylinder
leakage test. (4)
8.4 State FOUR causes of a low oil-pressure reading on an internal combustion
engine. (4)
8.5 State TWO possible causes and the corrective measures for a high
fuel-pressure reading during a fuel pressure test. (4)
8.6 State TWO manufacturers' specifications required before performing a
cooling system pressure test. (2)
8.7 State TWO functions of the radiator cap. (2)
[23]
Copyright reserved Please turn over
Mechanical Technology: Automotive 15 DBE/November 2024
NSC Confidential
QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)
9.1 State TWO disadvantages of a vehicle fitted with an automatic gearbox when
compared to a manual gearbox. (2)
9.2 Explain the operation of a torque converter. (5)
9.3 Draw a single epicyclic gear system and label the FOUR basic components. (5)
9.4 State ONE advantage of using EACH of the following gear ratios in the
gearbox of a motor vehicle:
9.4.1 Forward reduction (1st gear) (1)
9.4.2 Reverse gear (1)
9.4.3 Forward overdrive (5th gear) (1)
9.5 State ONE use of EACH of the following components with regard to an
automatic gearbox:
9.5.1 Hydraulic pistons (1)
9.5.2 Brake bands (1)
9.5.3 Transmission control unit (1)
[18]
Copyright reserved Please turn over
Mechanical Technology: Automotive 16 DBE/November 2024
NSC Confidential
QUESTION 10: SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY AND
ELECTRONICS) (SPECIFIC)
10.1 FIGURE 10.1 below shows a tyre wear pattern. Answer the questions that
follow.
One side of tyre
tread worn
excessively
FIGURE 10.1
10.1.1 Which wheel alignment angle will cause the tyre wear pattern
shown? (1)
10.1.2 State TWO faults on the vehicle suspension that could cause this
tyre wear. (2)
10.1.3 Describe TWO ways to correct the cause of this tyre wear. (2)
10.2 Define the following wheel alignment angles:
10.2.1 Positive caster (2)
10.2.2 King pin inclination (2)
10.3 Name THREE sensors found on an air-intake system of an internal
combustion engine. (3)
10.4 What is the function of the knock sensor fitted to the engine? (2)
10.5 Name TWO components of a distributorless ignition system (DIS). (2)
10.6 Name TWO chemical reactions that occur in the catalytic convertor. (2)
10.7 State TWO functions of the speed control system. (2)
Copyright reserved Please turn over
Mechanical Technology: Automotive 17 DBE/November 2024
NSC Confidential
10.8 FIGURE 10.8 below shows an exploded view of an alternator. Answer the
questions that follow.
Regulator
A C Rotor Rectifier
D
B
FIGURE 10.8
10.8.1 Label A–D. (4)
10.8.2 What is the function of the rotor? (2)
10.8.3 What does the regulator control in the alternator? (1)
10.8.4 What is the function of the rectifier? (2)
10.9 State THREE factors that influence the amount of fuel sprayed by the
injector. (3)
[32]
TOTAL: 200
Copyright reserved
Mechanical Technology: Automotive 1 DBE/November 2024
NSC Confidential
FORMULA SHEET FOR MECHANICAL TECHNOLOGY: AUTOMOTIVE
1. F ma
Where:
m = Mass
a = Acceleration
2. Work done = Force × Displacement OR W Fs
Force Displacement Fs
3. Power OR P
Time t
4. Torque Force Radius OR T Fr
5. IP P L A N n
Where:
IP Indicated power
P Mean effective pressure
L Stroke length
A Area of piston crown
N Number of power strokes per second
n Number of cylinders
6. BP = 2 π N T
Where:
BP Brake power
N Revolution s per second
T Torque
7. Brake power with Pröny brake = 2 π N F R
Where:
BP Brake power
N Revolution s per second
F Force
R Brake arm length
Copyright reserved Please turn over
Mechanical Technology: Automotive 2 DBE/November 2024
NSC Confidential
BP
8. Mechanical efficiency = 100%
IP
SV CV
9. Compression ratio
CV
Where:
SV Swept volume
CV Clearance volume
πD 2
10. SV = L
4
Where:
D Bore diameter
L Stroke length
SV
11. CV =
CR - 1
Product of teeth on driven gears
12. Gear ratio =
Product of teeth on driver gears
Copyright reserved
Study this subject
Recommended for this subject
%20MG%20Eng--ed5ab6d3-088f-425c-ade8-86186a031594/v1-3e0bd44f4bc86cf3bb1d/card.webp)
Memorandum
Mechanical Technology Grade 12 November 2024 NSC Memo (Eng)
_Afrikaans_hlayiso.com_--aadd113c-5a3b-4f4d-a4c4-3a80cd86f882/v1-fd2ca7edf910eab03a55/card.webp)
Memorandum
Mechanical Technology Grade 12 Eastern Cape Prelim 2024 Memo
%20GR12%20MEMO%20SEPT2024_Afrikaans_hlayiso.com_--2f874dd1-8c03-49a9-8c70-41ac528693d0/v1-55f44edf9664bf65cf74/card.webp)
Memorandum
Mechanical Technology Grade 12 Eastern Cape Prelim 2024 Memo

Memorandum
Mechanical Technology Grade 12 Eastern Cape Prelim 2024 Memo
_English_hlayiso.com_--2c18efa9-a7cc-42c1-a732-2ff3511c8c1c/v1-098ff39ac7fe2a71ec09/card.webp)
Memorandum
Mechanical Technology Grade 12 Eastern Cape Prelim 2024 Memo
%20MG%20Afr--03c703c8-8125-4d5a-a124-37013b381c7a/v1-02788e8df50b92af342d/card.webp)
Memorandum
Mechanical Technology Grade 12 NSC June 2024 Memo (Afr)
More from Grade 12 Mechanical Technology

Annual teaching plan
Gr 12 Weld Met ATP 2023 24
%20MG%20Afr--552ebeca-d294-4c37-b3fb-cded79fa438f/v1-b698b76db92c8affef7e/card.webp)
Memorandum
Mechanical Technology Grade 12 NSC June 2024 Memo (Afr)

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo
%20GR12%20MEMO%20SEPT2023_English_hlayiso.com_--dfc975c1-e179-4741-8d4f-e3b20c744c7e/v1-c61c66086bf36fcf31e0/card.webp)
Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

Memorandum