NATIONAL
SENIOR CERTIFICATE
GRADE 12
MECHANICAL TECHNOLOGY: FITTING AND MACHINING
NOVEMBER 2024
MARKING GUIDELINES
MARKS: 200
These marking guidelines consist of 23 pages.
Copyright reserved Please turn over
Skip to contentAll 2024 papers %20Eng--5d2e2bd0-b02f-4218-849f-e7933bc6c4d1/v1-2dba8a1dc6758c98b205/card.webp)
%20Afr--1e7205e4-aef1-4cc4-afdf-aac93562ae67/v1-094abcfa5c3eff1cb995/card.webp)
%20Eng--10859467-be3e-41fb-aee0-b797c385437d/v1-986e8982bfb6b966a34d/card.webp)


%20GR12%20MEMO%20SEPT2023_English_hlayiso.com_--dfc975c1-e179-4741-8d4f-e3b20c744c7e/v1-c61c66086bf36fcf31e0/card.webp)
View all


%20Afr_hlayiso.com_--7d638feb-7218-4b3c-9f4c-ce95803d6e4f/v1-e8a08d94a30d7d50ccd0/card.webp)
%20Eng_hlayiso.com_--1523a16f-2012-4f13-a922-86cbb5900666/v1-5068227f3cbbba17b78f/card.webp)
%20Afr_hlayiso.com_--8d31d25d-e192-4aa9-b448-efab233391a1/v1-28cf2259fca9bcde2f63/card.webp)
Mechanical Technology Grade 12 November 2024 NSC Memo (Eng)
Grade 12 Mechanical Technology memorandum from the November 2024 NSC (English), 23 pages. Read online or download the free PDF.
Mechanical Technology · Grade 12 · November 2024 NSC · 2024. Memorandum. Read online or download the PDF.
- Subject
- Mechanical Technology
- Grade
- Grade 12
- Document type
- Memorandum
- Year
- 2024
- Exam period
- November 2024 NSC
- Curriculum
- CAPS
- Pages
- 23
- File size
- 525.9 KB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 23
This exam
Document textSearch extracted text and jump to a page.
Mechanical Technology: Fitting and Machining 2 DBE/November 2024
NSC – Marking guidelines
QUESTION 1: MULTIPLE-CHOICE (GENERIC)
1.1 A✓ (1)
1.2 D✓ (1)
1.3 A✓ (1)
1.4 B✓ (1)
1.5 D✓ (1)
1.6 C✓ (1)
[6]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 3 DBE/November 2024
NSC – Marking guidelines
QUESTION 2: SAFETY (GENERIC)
2.1 Horizontal band saw (Already been switched on):
• Never leave the band saw unattended while in motion. ✓
• Switch off the band saw when leaving. ✓
• Use a brush or wooden rod to remove chips/swarf/filings. ✓
• When reaching around a revolving band saw, be careful that your clothes
do not get caught in the blade.
• Don't stop a revolving bandsaw blade with your hand. ✓
• Don't adjust the band saw while working. ✓
• Don't open any guard while in motion. ✓
• Keep hands away from action points. ✓
• Do not force the band saw blade into the material. ✓
• Apply cutting fluid if required. ✓
• Avoid overcrowding of persons around the machine. ✓
• Do not lean on the machine. ✓
• Check if the machine is running smoothly. ✓
(Any 2 x 1) (2)
2.2 First aid basic treatment:
• Examination ✓
• Diagnosis ✓
• Treatment ✓ (3)
2.3 Oxygen fittings with oil and grease:
It forms a flammable mixture. ✓ (1)
2.4 Disadvantages of the process layout:
• Production is not always continuous. ✓
• Transportation costs between process departments may be high. ✓
• Additional time is spent in testing and sorting as the product moves to
the different departments. ✓
• Damage to fragile goods may result from extra handling. ✓
(Any 2 x 1) (2)
2.5 Advantages of the product layout:
• Handling of material is limited to a minimum. ✓
• Time period of manufacturing cycle is less. ✓
• Production control is almost automatic. ✓
• Control over operations is easier. ✓
• Greater use of unskilled labour is possible. ✓
• Less total inspection is required. ✓
• Less total floor space is needed per unit of production. ✓
(Any 2 x 1) (2)
[10]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 4 DBE/November 2024
NSC – Marking guidelines
QUESTION 3: MATERIALS (GENERIC)
3.1 Filing test:
3.1.1 Files easily (1)
3.1.2 Hard to file (1)
3.1.3 Files easily (1)
3.2 Heat treatment:
It is the heating and cooling of metals under controlled conditions / as
to change their properties. (3)
3.3 Heating of metal:
If metal is heated too fast, the outside of the metal becomes hotter than
the inside, then it is very difficult to achieve a uniform structure. (4)
3.4 Case hardening:
• Low-carbon steel / Mild steel
• Low-alloy steel (2)
3.5 Tempering:
• It is to relieve the strains induced during the hardening process.
• Increase toughness.
• Decrease brittleness.
• Achieve a finer grain structure.
(Any 1 x 2) (2)
[14]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 5 DBE/November 2024
NSC – Marking guidelines
QUESTION 4: MULTIPLE-CHOICE (SPECIFIC)
4.1 B✓ (1)
4.2 A✓ (1)
4.3 B✓ (1)
4.4 C✓ (1)
4.5 D✓ (1)
4.6 D✓ (1)
4.7 C✓ (1)
4.8 A✓ (1)
4.9 B✓ (1)
4.10 C✓ (1)
4.11 A✓ (1)
4.12 D✓ (1)
4.13 A✓ (1)
4.14 C✓ (1)
[14]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 6 DBE/November 2024
NSC – Marking guidelines
QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC)
5.1 Disadvantages:
• The automatic feed of the machine cannot be used.
• Only short length tapers can be cut.
• It causes fatigue in the operator.
• Poor finish.
(Any 3 x 1) (3)
5.2 Taper calculations:
5.2.1 Small diameter:
θ D −d x
tan = tan 3,5 =
2 2l 368
7 85 − d x = 368 tan 3,5
tan =
2 2 368 x = 22,51 mm
OR
736 tan3,5 = 85 − d
d = D − 2x
45,02 = 85 − d
d = 85 − 2 (22,5 )
d = 85 − 45,02
d = 39,98 mm
d = 39,98 mm (4)
5.2.2 Set-over of the tailstock:
L (D − d)
Set − over =
2l
488 (85 − 39,98)
=
2 368
= 29,85 mm (3)
5.3 Key ways:
5.3.1 Width:
D
Width =
4
105
Width =
4
= 26, 25 mm (2)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 7 DBE/November 2024
NSC – Marking guidelines
5.3.2 Thickness:
D
Thickness =
6
105
Thickness =
6
= 17,50 mm (2)
5.3.3 Length:
Length = 1,5 diamter of shaft
= 1,5 105
= 157,50 mm (2)
5.4 Safety milling:
• Do not use your hands to remove cuttings while the machine is in
motion.
• Use a brush once the machine has stopped.
• Resist the habit of leaning on machinery.
• Do not talk to anyone while you are operating the machine.
• Place saw dust, or oil-absorbing compounds on slippery floors.
• Use a piece of leather or cloth for protection when you handle milling
cutters. / Do not use your bare hands when you handle milling cutters.
• Use safety goggles when cutting.
• Do not reach over or near rotating cutters.
• Never leave the machine running unattended.
• Make sure all guards are in place.
• Do not use the machine or come close to its moving parts while wearing
loose clothes.
• Never use an air hose to clean the milling machine.
• Stop the machine before you make any adjustments or take
measurements.
• Check that there is no oil or grease on the floor around the machine.
• Always clamp workpieces and holding devices safely and firmly.
• Do not use excessive force on the workpiece.
(Any 2 x 1) (2)
[18]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 8 DBE/November 2024
NSC – Marking guidelines
QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC)
6.1 Gear terminology:
6.1.1 Circular pitch:
CP = m π
=3π
= 9, 42 mm (2)
6.1.2 Number of teeth:
PCD CP T
m= PCD =
T π
PCD 9, 42 T
T = 186 =
m OR π
186 186 π
T = T=
3 9, 42
T = 62 teeth
= 62 teeth (3)
6.1.3 Dedendum:
Dedendum =1,157 m Dedendum =1,25 m
OR
=1,157 3 =1,25 3
= 3,47 mm = 3,75 mm
(2)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 9 DBE/November 2024
NSC – Marking guidelines
6.2 Dovetails:
6.2.1 Maximum width distance of dovetail: (W)
Calculate DE or y:
AD
tan =
DE DE
tan =
AD 32
tan60 =
DE = tan AD OR DE
= tan30 32 32
DE =
= 18,48 mm tan60
= 18,48 mm
W = 125 + 2(DE)
= 125 + 2(18,48)
= 125 + 36,96
= 161,96 mm (6)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 10 DBE/November 2024
NSC – Marking guidelines
6.2.2 Distance over the rollers: (M)
Calculate AC or x:
BC
Tan =
AC AC
Tan =
BC
BC
AC = ✓ AC = Tan BC ✓
Tan
OR
7 = Tan60 o 7 ✓
= ✓
Tan30 o
=12,12 mm ✓
=12,12 mm ✓
M = w + [(2(AC) + 2(R)] ✓
= 125 + [2(12,12) + 2(7)] ✓
= 125 + (24,24 + 14)
= 163,24 mm ✓
OR
M = w + 2(AC + R) ✓
= 125 + 2(12,12 + 7) ✓
= 125 + 24,24 + 14
= 163,24 mm ✓
OR
M= w + 2(AC) + 2(R) ✓
= 125 + 2(12,12) + 2(7) ✓
= 125 + 24,24 + 14
= 163,24 mm ✓ (6)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 11 DBE/November 2024
NSC – Marking guidelines
6.3 Milling of spur gear:
6.3.1 Indexing:
40
Indexing =
n
40
=
101
40
Indexing =
A
40
=
100
2 5
=
5 5
10
=
25
Approximate indexing:
No full turns and 10 holes on a 25-hole circle ✓
OR
No full turns and 12 holes on a 30-hole circle ✓ (4)
6.3.2 Change gears:
Dr 40
= (A − n ) Dr ( A − n ) 40
Dn A =
Dr ✓ 40 Dn A 1
= (100 − 101) ✓
Dn 100 ✓ Dr (100 − 101) 40
=
40 Dn 100 ✓ 1
= −1 OR
100 2 20
− 40 =− ✓
= ✓ 5 20
100
Dr 40 ✓
Dr 40 ✓ =
= Dn 100 ✓
Dn 100 ✓ (5)
[28]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 12 DBE/November 2024
NSC – Marking guidelines
QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC)
7.1 Different indenters:
7.1.1 On the anvil/platform. ✓ (1)
7.1.2 • By calculation ✓
• Using the table ✓ (2)
7.2 Label A-D:
A. Datum line/Reading line✓
B. Fixed anvil ✓
C. Thimble ✓
D. Ratchet ✓ (4)
7.3 Function of screw thread micrometer:
To measure ✓ the pitch diameter ✓ of a screw thread. (2)
7.4 Height of a screw thread:
H = 0,866 × Pitch (P)
H = 0,866 × 2,5 ✓
H = 2,17 mm ✓ (2)
7.5 Reading of depth micrometer:
The depth micrometer reads in the opposite direction. / In a depth
micrometer the reading is taken from right to left and a screw thread
micrometer reads from left to right on the datum line. ✓ (1)
7.6 Interchangeable rods:
• Interchangeable rods are used to measure extra depth. ✓
• Interchangeable rods are used to measure more than 25 mm. ✓
(Any 1 x 1) (1)
[13]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 13 DBE/November 2024
NSC – Marking guidelines
QUESTION 8: FORCES (SPECIFIC)
8.1 System of forces:
45 N
25 sin 30° 45sin90°
25 N 25cos30°
150 sin 30°
60 º
30 º
80 sin 45°
45 º
150cos30° 150 N
80cos45° N
80 N
8.1.1 ∑ Horizontal component:
HC = 45cos90 − 25cos30 − 80cos45 + 150cos30
✓ ✓ ✓
HC = 0 − 21,65 − 56,57 + 129,90
(4)
HC = 51,68N ✓
8.1.2 ∑ Vertical component:
VC = 45sin90 + 25sin30 − 80sin45 − 150sin30
✓ ✓ ✓ ✓
VC = 45 + 12,5 − 56,57 − 75
(5)
VC = − 74,07 N ✓
OR
Force θ 8.1.2 ∑VC/y = Fsinθ 8.1.1 ∑HC/x = Fcosθ
45N 90º VC = 45sin90º 45 N ✓ HC = 45cos90º 0N
25N 150º VC = 25sin150º 12,5 N ✓ HC = 25cos150º -21,65 N ✓
80N 225º VC = 80sin225º - 56,57 N ✓ HC = 80cos225º -56,57 N ✓
150N 330º VC = 150sin330º -75 N ✓ HC = 150cos330º 129,90 N ✓
Total -74,07N ✓ 51,68N ✓
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 14 DBE/November 2024
NSC – Marking guidelines
8.1.3 Resultant:
R 2 = VC2 + HC2
R2 = ( −74,04 ) + ( 51,68 )
2 2
✓
R = 90,32 N ✓ (2)
8.1.4 Angle and direction of equilibrant:
VC
tan θ =
HC
α
− 74,07
θ = tan −1 ✓
51,68
θ = 55,10° ✓
OR
HC
tan =
VC
51,68
= tan −1 ✓
− 74,07
= 34,90° ✓
Direction:
E = 90,32 N 55,10° N from W ✓
OR
✓
E = 90,32 N 34,90° W from N
OR
E = At a Bearing of 325,10° (3)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 15 DBE/November 2024
NSC – Marking guidelines
8.2 Calculations, UDL and supports A and B.
8.2.1 UDL:
UDL = 10 N/m x 4 m ✓
UDL = 40 N ✓ (2)
8.2.2 Reaction in support A:
Take moments about B:
LHM = RHM
✓ ✓ ✓
( 60 1,5 ) + ( 40 5 ) + ( 75 11) = ( A 12 )
90 + 200 + 825 = 12A
1115
A=
12
A = 92,92 N ✓
Reaction in support B:
Take moments about A:
LHM = RHM
✓ ✓ ✓
(B 12 ) = ( 75 1) + ( 40 7 ) + ( 60 10,5 )
12B = 75 + 280 + 630
985
B=
12
B = 82,08 N ✓ (8)
8.3 Stress calculations:
8.3.1 Stress:
F
σ =
A
110000
σ= ✓
7,07 10 -4
σ = 155586987, 3
σ = 155,59 MPa ✓ (2)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 16 DBE/November 2024
NSC – Marking guidelines
8.3.2 Diameter:
π d2
A=
4
4A
d= ✓
π
d=
(
4 7,07 10 − 4 )
✓
π
d = 0,03 m ✓
d = 30 mm ✓ (4)
8.3.3 The original length:
ΔL
ε=
oL
ΔL
oL = ✓
ε
0,0001
oL = ✓
1,64 10 -5
oL = 6,1 m
oL = 6097,56 mm ✓ (3)
[33]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 17 DBE/November 2024
NSC – Marking guidelines
QUESTION 9: MAINTENANCE (SPECIFIC)
9.1 Mechanical drives:
• Gear drive ✓
• Belt drive ✓
• Chain drive ✓
• Hydraulic drives ✓
• Pneumatic drives ✓
• Shaft drives ✓
(Any 3 x 1) (3)
9.2 Maintenance on operating systems:
• Maintenance is to ensure that the system/machine always operates ✓ at
an optimal level. ✓
• Prevent machinery from breakdown ✓ and let the machines last
longer. ✓
(Any 1 x 2) (2)
9.3 Preventative maintenance procedures on gear drives:
• Check and refill lubricant levels. ✓
• Ensure that gears are properly secured to shafts. ✓
• Cleaning and replacement of oil filters. ✓
• Reporting excessive noise and wear, vibration and overheating for
expert attention. ✓
• Make sure that the gears are properly aligned. ✓
• Ensure that the correct type of oil/lubricant is used. ✓
(Any 3 x 1) (3)
9.4 Subgroups of preventative maintenance:
• Planned/Scheduled maintenance ✓
• Condition-based maintenance ✓ (2)
9.5 Polyester resins:
To strengthen the glass fibre. ✓ (1)
9.6 Lack of preventive maintenance:
• Risk of injury. ✓
• Risk of death. ✓
• Financial loss. ✓
• Damage of machines/equipment. ✓
• Poor performance of machines/equipment. ✓
• Loss of valuable production time. ✓
• Damage to material/work piece. ✓
(Any 3 x 1) (3)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 18 DBE/November 2024
NSC – Marking guidelines
9.7 Thermo-hardened and thermoplastic composites:
Thermo-hardened: This material cannot be re-heated ✓ to be softened,
shaped and moulded.✓
Thermoplastic: These plastics can be re-heated ✓ and therefore reshaped
in various ways. ✓ (4)
[18]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 19 DBE/November 2024
NSC – Marking guidelines
QUESTION 10: JOINING METHODS (SPECIFIC)
10.1 Square thread:
10.1.1 Pitch diameter:
Lead
P itch =
Number of starts
40
=
4
= 10 mm
P
P D = OD −
2
10
= 105 −
2
= 100 mm (4)
10.1.2 Helix angle of the thread:
L ead
T anθ =
π P D
40
T anθ =
π 100
θ = tan−1 ( 0,127323954 )
= 7, 26 (4)
10.1.3 Leading angle:
Leading angle = 90° – (helix angle + clearance angle)
= 90° – (7,26° + 4°) ✓
= 78,74° ✓ (2)
10.1.4 Following angle:
Following angle = 90° + (helix angle – clearance angle)
= 90° + (7,26° – 4°) ✓
= 93,26° ✓ (2)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 20 DBE/November 2024
NSC – Marking guidelines
10.2 Square thread:
A. Crest- /Outside- /Major- /Nominal diameter ✓
B. Pitch- /Effective- /Mean diameter ✓
C. Helix angle ✓
D. Cutting tool ✓ (4)
10.3 Uses of square thread:
• Power transmissions ✓
• Vice screws ✓
• Lathe lead and feed screws / half nuts ✓
• Press screws ✓
• Clamping devices ✓
• Linear actuators ✓
• Adjustment mechanisms ✓
• Tapping and thread cutting ✓
• Threaded spindles ✓
• Lifting mechanisms ✓
(Any 2 x 1) (2)
[18]
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 21 DBE/November 2024
NSC – Marking guidelines
QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC)
11.1 Hydraulic systems:
11.1.1 Fluid pressure:
F
P =
A
600
P = ✓
0,2
P = 3000 Pa (2)
11.1.2 Force applied:
f
P =
a
f =P a ✓
f = 3000 0,018 ✓
f = 54 N ✓ (3)
11.1.3 Displacement l:
VPlunger = VRam
a = AL
AL
= ✓
a
0,2 0,03
= ✓
0,018
= 0,333 m
= 333,3 mm ✓ (3)
11.2 Hydraulic pressure:
Pressure gauge ✓ (1)
11.3 Purpose of hydraulic filter:
• To restrict dirt in system. ✓
• To protect the pump. ✓
• Protect the valves. ✓
• Protect the actuators. ✓
(Any 1 x 1) (1)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 22 DBE/November 2024
NSC – Marking guidelines
11.4 Hydraulic valve:
11.4.1 Identify valve:
• Non-return valve ✓
• One-way valve ✓
(Any 1 x 1) (1)
11.4.2 Functions:
• Ensure one direction flow. ✓
• Prevent back flow. ✓
• Act as a pressure relief valve. ✓
(Any 2 x 1) (2)
11.5 Belt drive:
11.5.1 Rotational frequency:
NDN D DN = NDR D DR
NDN D DN
NDR = ✓
D DR
1100 600 ✓
NDR =
220 ✓
3000 r/min
NDR =
60
NDR = 50 r/sec ✓ (4)
11.5.2 Torque:
2 π NT
Ρ=
60
P 60
T= ✓
2 π N
236,65 10 3 60
T= ✓
2 π 1100
T = 2054,40 Nm ✓ (3)
Copyright reserved Please turn over
Mechanical Technology: Fitting and Machining 23 DBE/November 2024
NSC – Marking guidelines
11.6 Gear drive:
11.6.1 Rotational frequency of the output shaft NA in r/s:
Ninput Product of the number of teeth on driven gears
=
Noutput Product of the number of teeth on driving gears
NA TB TD
= ✓
ND TA TC
980 24 42 ✓
=
ND 45 20 ✓
45 20 980
ND =
24 42
ND = 875 r / min
ND = 14,58 r / sec ✓ (4)
11.6.2 Gear ratio:
Product of teeth on driven gear
Gear ratio =
Product of teeth on driver gear
24 42 ✓
Gear ratio =
45 20 ✓
Gear ratio = 1,12 : 1 ✓
OR
Ninput
Gear ratio =
Noutput
16,33 ✓ 980 ✓
Gear ratio = OR
14,58 ✓ 875 ✓
Gear ratio = 1,12 : 1 ✓
(3)
11.6.3 Direction:
Clockwise ✓ (1)
[28]
TOTAL: 200
Copyright reserved
Study this subject
Recommended for this subject
%20Eng--5d2e2bd0-b02f-4218-849f-e7933bc6c4d1/v1-2dba8a1dc6758c98b205/card.webp)
Question paper
Mechanical Technology Grade 12 November 2024 NSC QP (Eng)
%20Afr--1e7205e4-aef1-4cc4-afdf-aac93562ae67/v1-094abcfa5c3eff1cb995/card.webp)
Question paper
Mechanical Technology Grade 12 November 2024 NSC QP (Afr)
%20Eng--10859467-be3e-41fb-aee0-b797c385437d/v1-986e8982bfb6b966a34d/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2024 QP (Eng)

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo
%20GR12%20MEMO%20SEPT2023_English_hlayiso.com_--dfc975c1-e179-4741-8d4f-e3b20c744c7e/v1-c61c66086bf36fcf31e0/card.webp)
Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo
More from Grade 12 Mechanical Technology

Annual teaching plan
Gr 12 Weld Met ATP 2023 24

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

Question paper
Mechanical Technology Grade 12 Eastern Cape Mock 2023 QP
%20Afr_hlayiso.com_--7d638feb-7218-4b3c-9f4c-ce95803d6e4f/v1-e8a08d94a30d7d50ccd0/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2023 QP (Afr)
%20Eng_hlayiso.com_--1523a16f-2012-4f13-a922-86cbb5900666/v1-5068227f3cbbba17b78f/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2023 QP (Eng)
%20Afr_hlayiso.com_--8d31d25d-e192-4aa9-b448-efab233391a1/v1-28cf2259fca9bcde2f63/card.webp)
Question paper