NATIONAL
SENIOR CERTIFICATE
GRADE 12
MECHANICAL TECHNOLOGY: AUTOMOTIVE
NOVEMBER 2024
MARKING GUIDELINES
MARKS: 200
These marking guidelines consist of 19 pages.
Copyright reserved Please turn over
Skip to contentAll 2024 papers %20Eng--5d2e2bd0-b02f-4218-849f-e7933bc6c4d1/v1-2dba8a1dc6758c98b205/card.webp)
%20Afr--1e7205e4-aef1-4cc4-afdf-aac93562ae67/v1-094abcfa5c3eff1cb995/card.webp)
%20Eng--10859467-be3e-41fb-aee0-b797c385437d/v1-986e8982bfb6b966a34d/card.webp)


%20GR12%20MEMO%20SEPT2023_English_hlayiso.com_--dfc975c1-e179-4741-8d4f-e3b20c744c7e/v1-c61c66086bf36fcf31e0/card.webp)
View all


%20Afr_hlayiso.com_--7d638feb-7218-4b3c-9f4c-ce95803d6e4f/v1-e8a08d94a30d7d50ccd0/card.webp)
%20Eng_hlayiso.com_--1523a16f-2012-4f13-a922-86cbb5900666/v1-5068227f3cbbba17b78f/card.webp)
%20Afr_hlayiso.com_--8d31d25d-e192-4aa9-b448-efab233391a1/v1-28cf2259fca9bcde2f63/card.webp)
Mechanical Technology Grade 12 November 2024 NSC Memo (Eng)
Grade 12 Mechanical Technology memorandum from the November 2024 NSC (English), 19 pages. Read online or download the free PDF.
Mechanical Technology · Grade 12 · November 2024 NSC · 2024. Memorandum. Read online or download the PDF.
- Subject
- Mechanical Technology
- Grade
- Grade 12
- Document type
- Memorandum
- Year
- 2024
- Exam period
- November 2024 NSC
- Curriculum
- CAPS
- Pages
- 19
- File size
- 434.6 KB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 19
This exam
Document textSearch extracted text and jump to a page.
Mechanical Technology: Automotive 2 DBE/November 2024
NSC – Marking Guidelines
QUESTION 1: MULTIPLE-CHOICE (GENERIC)
1.1 A✓ (1)
1.2 D✓ (1)
1.3 A✓ (1)
1.4 B✓ (1)
1.5 D✓ (1)
1.6 C✓ (1)
[6]
Copyright reserved Please turn over
Mechanical Technology: Automotive 3 DBE/November 2024
NSC – Marking Guidelines
QUESTION 2: SAFETY (GENERIC)
2.1 Horizontal band saw (Already been switched on):
• Never leave the band saw unattended while in motion. ✓
• Switch off the band saw when leaving. ✓
• Use a brush or wooden rod to remove chips/swarf/filings. ✓
• When reaching around a revolving band saw, be careful that your clothes
do not get caught in the blade.
• Don't stop a revolving bandsaw blade with your hand. ✓
• Don't adjust the band saw while working. ✓
• Don't open any guard while in motion. ✓
• Keep hands away from action points. ✓
• Do not force the band saw blade into the material. ✓
• Apply cutting fluid if required. ✓
• Avoid overcrowding of persons around the machine. ✓
• Do not lean on the machine. ✓
• Check if the machine is running smoothly. ✓
(Any 2 x 1) (2)
2.2 First aid basic treatment:
• Examination ✓
• Diagnosis ✓
• Treatment ✓ (3)
2.3 Oxygen fittings with oil and grease:
It forms a flammable mixture. ✓ (1)
2.4 Disadvantages of the process layout:
• Production is not always continuous. ✓
• Transportation costs between process departments may be high. ✓
• Additional time is spent in testing and sorting as the product moves to
the different departments. ✓
• Damage to fragile goods may result from extra handling. ✓
(Any 2 x 1) (2)
2.5 Advantages of the product layout:
• Handling of material is limited to a minimum. ✓
• Time period of manufacturing cycle is less. ✓
• Production control is almost automatic. ✓
• Control over operations is easier. ✓
• Greater use of unskilled labour is possible. ✓
• Less total inspection is required. ✓
• Less total floor space is needed per unit of production. ✓
(Any 2 x 1) (2)
[10]
Copyright reserved Please turn over
Mechanical Technology: Automotive 4 DBE/November 2024
NSC – Marking Guidelines
QUESTION 3: MATERIALS (GENERIC)
3.1 Filing test:
3.1.1 Files easily (1)
3.1.2 Hard to file (1)
3.1.3 Files easily (1)
3.2 Heat treatment:
It is the heating and cooling of metals under controlled conditions / as
to change their properties. (3)
3.3 Heating of metal:
If metal is heated too fast, the outside of the metal becomes hotter than
the inside, then it is very difficult to achieve a uniform structure. (4)
3.4 Case hardening:
• Low-carbon steel / Mild steel
• Low-alloy steel (2)
3.5 Tempering:
• It is to relieve the strains induced during the hardening process.
• Increase toughness.
• Decrease brittleness.
• Achieve a finer grain structure.
(Any 1 x 2) (2)
[14]
Copyright reserved Please turn over
Mechanical Technology: Automotive 5 DBE/November 2024
NSC – Marking Guidelines
QUESTION 4: MULTIPLE-CHOICE (SPECIFIC)
4.1 C✓ (1)
4.2 B✓ (1)
4.3 C✓ (1)
4.4 B✓ (1)
4.5 D✓ (1)
4.6 A✓ (1)
4.7 B✓ (1)
4.8 C✓ (1)
4.9 C✓ (1)
4.10 C✓ (1)
4.11 D✓ (1)
4.12 B✓ (1)
4.13 C✓ (1)
4.14 D✓ (1)
[14]
Copyright reserved Please turn over
Mechanical Technology: Automotive 6 DBE/November 2024
NSC – Marking Guidelines
QUESTION 5: TOOLS AND EQUIPMENT (SPECIFIC)
5.1 Compression test procedures:
5.1.1 Air filter removed:
• To allow maximum amount of air to enter the cylinder. ✓
• To get the correct reading ✓
(Any 1 x 1) (1)
5.1.2 Clean around spark plug:
Avoid dirt falling into the engine through the spark plug hole. ✓ (1)
5.1.3 Disconnect ignition system:
• To prevent a spark developing. ✓
• To prevent a fire hazard. ✓
• To prevent the possibility of shock. ✓
(Any 1 x 1) (1)
5.1.4 Record readings:
• To check if there is a difference in the compression between
each cylinder. ✓
• To compare the compression in all cylinders to the
specification. ✓
(Any 1 x 1) (1)
5.2 Cylinder leakage tester:
5.2.1 Labels:
A. Pressure regulator ✓
B. Adapter hose/pipe ✓
C. Leakage gauge ✓ (3)
5.2.2 Unit of measurement:
kPa/Bar/PSI ✓ (1)
5.2.3 Unit of measurement:
Percentage (%) ✓ (1)
Copyright reserved Please turn over
Mechanical Technology: Automotive 7 DBE/November 2024
NSC – Marking Guidelines
5.3 Exhaust gas analyser:
• The hot exhaust system should not be touched with the bare hand.
• Perform the test in a well-ventilated area.
• Keep hands and tools clear from moving engine parts.
• Place the analyser in a secure position to prevent it from falling.
• The inlet hose must not be restricted in any way.
• The hose connections must be airtight.
• Ensure no exhaust, manifolds or vacuum system leaks.
• Condensate must be blown out of the hoses.
• The condenser must be drained after each test.
• When the paper filter becomes light grey, it should be changed.
• The exhaust gas filter must be changed regularly.
• Wear all necessary PPE.
• Ensure that the gas analyser is safely connected to the battery.
(Any 4 x 1) (4)
5.4 On-board diagnostic scanner:
• Scan diagnostic trouble codes
• Clear the trouble codes
• Programme (e.g. make adjustment to electronic control unit)
• Retrieve information
(Any 2 x 1) (2)
5.5 Wheel balancing machine:
5.5.1 Identify:
Wheel balancing machine ✓ (1)
5.5.2 Functions:
• Balance a wheel dynamically. ✓
• Balance a wheel statically. ✓ (2)
5.5.3 Safety device:
Safety cover/hood/guard ✓ (1)
5.5.4 Calibration reason:
So that the machine can display accurate/optimum results. (1)
5.6 Measure camber with the bubble gauge:
1. Ensure bubble gauge is on the centre of the wheel hub.
2. Level bubble gauge.
3. Read the CAMBER angle. (3)
[23]
Copyright reserved Please turn over
Mechanical Technology: Automotive 8 DBE/November 2024
NSC – Marking Guidelines
QUESTION 6: ENGINES (SPECIFIC)
6.1 Function of the crankshaft:
To convert reciprocating motion into rotary motion. (2)
6.2 Part attached to crankshaft nose:
Vibration damper (1)
6.3 Reciprocating mass kept light:
• To reduce engine vibrations.
• Less twisting force acting on the crankshaft.
• The engine is able to reach its speed sooner.
• Reduced rate of wear on the bore.
(Any 1 x 1) (1)
6.4 Obtain the firing order:
• Determine which valves are the inlet or which are the exhaust valves.
• Turn the engine in the direction it rotates.
• Observe the order in which the valves open to determine the firing
order. (3)
6.5 Engine configuration:
6.5.1 Type of engine configuration:
Flat engine/boxer type engine/horizontally opposed engine (1)
6.5.2 Labels:
A. Connecting rod
B. Piston
C. Crankshaft/Crankshaft nose (3)
6.6 Crankpins of six-cylinder in-line engine:
120°
120° 120°
• THREE crankpins
• Position of crankpins
• Angles labeled
(3)
Copyright reserved Please turn over
Mechanical Technology: Automotive 9 DBE/November 2024
NSC – Marking Guidelines
6.7 Turbochargers:
6.7.1 Advantages:
• Increases engine torque.
• Increases engine power.
• Increases volumetric efficiency.
• Improves fuel consumption.
• No engine power sapped./Driven by exhaust gases.
• Power loss due to low atmospheric pressure/high altitude
eliminated.
• Smaller capacity engine required for similar power output.
• It is generally cheaper than a supercharger.
(Any 3 x 1) (3)
6.7.2 Synthetic oil for turbochargers:
• Can withstand high pressures.
• Can withstand high temperatures.
• Higher flash point.
• Tends to have a low viscosity.
• Capable of better cooling.
• Faster flow rate.
(Any 2 x 1) (2)
6.7.3 Turbocharger without vanes:
Non-variable turbocharger (1)
6.8 Turbocharger terms:
6.8.1 Boost:
Increase of intake manifold pressure above atmospheric
pressure. (2)
6.8.2 Turbo lag:
The delay between pressing the accelerator pedal and feeling
the turbo kick in. (2)
6.9 Supercharger:
6.9.1 Identify supercharger:
Twin-Screw supercharger (1)
6.9.2 Label supercharger:
A. Pulley
B. Casing/housing
C. Twin screw (3)
[28]
Copyright reserved Please turn over
Mechanical Technology: Automotive 10 DBE/November 2024
NSC – Marking Guidelines
QUESTION 7: FORCES (SPECIFIC)
7.1 Definition of terms:
7.1.1 Clearance volume:
The volume of the space above the piston crown in the cylinder
when the piston is at TDC. (2)
7.1.2 Compression ratio:
The relationship between the total volume and the clearance
volume of a cylinder. (2)
7.2 Calculate the work done:
Work = force distance Work = force distance
= F s = F s
= (690 10 ) 2 OR = ( 690 9,81) 2
= 13800 J = 13537,8 J
= 13 ,8 k J = 13,54 k J (3)
7.3 Methods to lower the clearance volume:
• Fit thinner gasket between cylinder block and cylinder head.
• Fit piston with suitable higher crowns.
• Machine (Skim) cylinder head.
• Machine (Skim) engine block.
(Any 2 x 1) (2)
7.4 Cylinder:
7.4.1 Labels:
A. Stroke length
B. Bore/cylinder diameter (2)
7.4.2 Calculate the swept volume:
π D2
Swept volume = L
4
8,3 2
= 7,9
4
= 427,44 cm 3 (3)
7.4.3 Calculate the clearance volume:
SV
CV =
CR − 1
427 , 44
=
9 −1
= 53,43 cm 3 (3)
Copyright reserved Please turn over
Mechanical Technology: Automotive 11 DBE/November 2024
NSC – Marking Guidelines
7.5 Calculate the indicated power:
P = 1400 10 3
110
L=
1000
= 0,11 m
π D2
Area =
4
π 0,1 2
=
4
= 0,00785398 m 2
3600
N=
60 2
= 30 firing strokes per second
IP = PLANn
( )
= 1400 10 3 (0, 11) (0,00785398 ) (30 ) (4 )
= 145 ,14 kW (7)
7.6 Calculations:
7.6.1 Torque:
Torque = Force radius
350
= 50
1000
= 17,5 Nm (3)
7.6.2 Brake power:
BP = 2 NT
2000
= 2 17,5
60
= 3,67 kW (3)
7.6.3 Mechanical efficiency:
BP
ME = 100
IP
3,67
= 100
50
= 7,33 % (2)
[32]
Copyright reserved Please turn over
Mechanical Technology: Automotive 12 DBE/November 2024
NSC – Marking Guidelines
QUESTION 8: MAINTENANCE (SPECIFIC)
8.1 Exhaust gas analysis:
High carbon monoxide (CO) reading:
8.1.1 POSSIBLE CAUSES 8.1.2 CORRECTIVE MEASURES
• Too rich mixture. ✓ • Reset/adjust the air fuel mixture. ✓
• Dirty or restricted air filter. ✓ • Replace/Clean air filter. ✓
• Ignition misfire. ✓ • Repair ignition misfire. ✓
• Thermostat stuck open. ✓ • Replace thermostat. ✓
• Faulty coolant sensor. ✓ • Replace coolant sensor. ✓
• Blocked PCV valve. ✓ • Unblock/clean/replace PCV valve. ✓
• Faulty catalytic convertor. ✓ • Replace catalytic convertor. ✓
• Carburettor flooding. ✓ • Correct carburettor fault. ✓
• Choke valve stuck closed. ✓ • Repair choke valve. ✓
• Fuel pressure too high. ✓ • Check and repair the return fuel line
of restrictions or kinks. ✓
• Replace fuel pressure regulator✓
• Select correct pump according to
vehicle specification. ✓
(Any 1 x 1) (Any 1 x 1)
Low carbon dioxide (CO2) reading:
8.1.3 POSSIBLE CAUSES 8.1.4 CORRECTIVE MEASURES
• Incorrect air-fuel mixture. ✓ • Reset/ adjust the air fuel mixture. ✓
• Dirty or restricted air filter. ✓
• Replace/Clean air filter. ✓
• Ignition misfire. ✓ • Repair ignition misfire. ✓
• Thermostat stuck open. ✓ • Replace thermostat. ✓
• Faulty coolant sensor. ✓ • Replace coolant sensor. ✓
• Blocked PCV valve. ✓ • Unblock clean/replace PCV valve. ✓
• Faulty catalytic convertor. ✓ • Replace catalytic convertor. ✓
• Carburettor flooding. ✓ • Correct carburettor fault. ✓
• Choke valve stuck closed. ✓ • Repair choke valve. ✓
• Fuel pressure too high. ✓ • Check and repair the return fuel line
of restrictions or kinks. ✓
• Replace fuel pressure regulator✓
• Select correct pump according to
vehicle specification. ✓
• Exhaust gas leaks. ✓ • Repair exhaust leaks. ✓
• Vacuum leaks on the intake. ✓ • Repair vacuum leaks on the intake. ✓
(Any 1 x 1) (Any 1 x 1) (4)
Copyright reserved Please turn over
Mechanical Technology: Automotive 13 DBE/November 2024
NSC – Marking Guidelines
8.2 Compression test:
8.2.1 Maximum variation allowed:
10% ✓ (1)
8.2.2 Low compression reading:
POSSIBLE CAUSES CORRECTIVE MEASURES
• Worn rings. ✓ • Fit new rings. ✓
• Worn piston. ✓ • Fit new pistons. ✓
• Worn bore. ✓ • Re-bore the cylinders or resleeve. ✓
• Leaking inlet valve. ✓ • Replace or lap valve. ✓
• Leaking exhaust valve. ✓ • Replace or lap valve. ✓
• Blown head gasket. ✓ • Replace head gasket. ✓
• Cracked cylinder head. ✓ • Replace or repair cylinder head. ✓
• Cracked engine block. ✓ • Replace engine block. ✓
(Any 1 x 1) (Any 1 x 1) (2)
8.3 Cylinder leakage test locations:
• Exhaust pipe/system ✓
• Intake system ✓
• Oil filler hole ✓
• Dipstick ✓
• Expansion tank/radiator ✓
• Adjacent spark plug hole ✓
(Any 4 x 1) (4)
8.4 Causes of a low oil pressure reading:
• Blocked strainer ✓
• Worn oil pump ✓
• Oil viscosity too low ✓
• Dirty oil ✓
• Low oil level ✓
• Blocked oil filter ✓
• Blocked oil channels ✓
• Excessive oil clearances ✓
• Defective pressure relief valve ✓
(Any 4 x 1) (4)
8.5 High fuel pressure reading:
POSSIBLE CAUSES CORRECTIVE MEASURES
• Restriction in the return fuel line• Check and repair the return fuel line
post the fuel tester. ✓ of restrictions or kinks. ✓
• Faulty fuel pressure regulator. ✓ • Replace fuel pressure regulator. ✓
• Wrong fuel pump used. ✓ • Select correct pump according to
vehicle specification. ✓
(Any 2 x 1) (Any 2 x 1) (4)
Copyright reserved Please turn over
Mechanical Technology: Automotive 14 DBE/November 2024
NSC – Marking Guidelines
8.6 Cooling system pressure test manufacturers' specifications:
• Coolant (Antifreeze-water) ratio. ✓
• Pressure in the cooling system. ✓
• Pressure on the radiator cap. ✓
(Any 2 x 1) (2)
8.7 Functions of the radiator cap:
• Regulate the cooling system pressure. ✓
• Seals the cooling system from leaks. ✓
• Allows coolant to be drawn back into the radiator when engine cools
down. ✓
(Any 2 x 1) (2)
[23]
Copyright reserved Please turn over
Mechanical Technology: Automotive 15 DBE/November 2024
NSC – Marking Guidelines
QUESTION 9: SYSTEMS AND CONTROL (AUTOMATIC GEARBOX) (SPECIFIC)
9.1 Disadvantages of automatic gearbox:
• More expensive to manufacture. ✓
• Repairs are expensive. ✓
• Special tools and training needed to repair gearbox. ✓
• Special towing techniques must be used when towed over a long
distance. ✓
• Generally heavier than a manual gearbox. ✓
• Vehicle cannot be push-started. ✓
(Any 2 x 1) (2)
9.2 Torque converter operation:
• The spinning pump/impeller throws the oil into the vanes of the turbine. ✓
• This turbine rotates the gearbox input shaft. ✓
• The oil circulates through the turbine vanes and strikes the stator. ✓
• The stator redirects the path of the oil in the direction of pump rotation. ✓
• Torque is multiplied when it leaves the pump again to enter the turbine. ✓ (5)
9.3 Single epicyclic gear system:
Annulus
Planetary
Gear
Planetary
Carrier
Sun Gear
A B
• Complete sketch ✓
Candidate may draw either sketches A or B. (5)
9.4 Advantages of gear ratios:
9.4.1 Forward reduction (1st gear):
• Improved pull away of vehicle. ✓
• Increased torque output. ✓
• Easier hill climbing. ✓ (1)
9.4.2 Reverse gear:
Vehicle is able to travel backwards. ✓ (1)
Copyright reserved Please turn over
Mechanical Technology: Automotive 16 DBE/November 2024
NSC – Marking Guidelines
9.4.3 Forward overdrive (5th gear):
• Increase speed ✓
• Decrease engine revolutions ✓
• Better fuel economy ✓
(Any 1 x 1) (1)
9.5 Components relating to an automatic gearbox:
9.5.1 Hydraulic pistons:
• Control the brake bands which allows for the change of gear
ratio. ✓
• Engage the clutches which allows for the change of gear
ratio. ✓
(Any 1 x 1) (1)
9.5.2 Brake bands:
The brake band holds the annulus stationary. ✓ (1)
9.5.3 Transmission control unit:
It controls the electronic gear shifting in an automatic
gearbox. ✓ (1)
[18]
Copyright reserved Please turn over
Mechanical Technology: Automotive 17 DBE/November 2024
NSC – Marking Guidelines
QUESTION 10: SYSTEMS AND CONTROL (AXLES, STEERING GEOMETRY
AND ELECTRONIC) (SPECIFIC)
10.1 Tyre wear pattern:
10.1.1 Cause the tyre wear pattern:
Camber ✓ (1)
10.1.2 Faults on the vehicle suspension:
• Suspension misalignment ✓
• Worn wheel bearings ✓
• Bent strut ✓
• Bent/Damaged lower control arms ✓
• Damaged lower control arms bushes ✓
• Damaged strut mountings ✓
• Worn ball joints ✓
(Any 2 x 1) (2)
10.1.3 Correct tyre wear cause:
• Re-align suspension ✓
• Replace wheel bearings ✓
• Replace strut ✓
• Replace lower control arm ✓
• Replace lower control arm bushes ✓
• Replace strut mountings ✓
• Replace ball joints ✓
(Any 2 x 1) (2)
10.2 Definitions of alignment angles:
10.2.1 Positive caster:
Positive caster is the backward tilt of the king pin at the top, ✓
when viewed from the side. ✓ (2)
10.2.2 King pin inclination:
King pin inclination is the inward tilt of the top ✓ of the king pin
viewed from the front. ✓ (2)
10.3 Air-intake system sensors:
• Throttle position sensor (TPS) ✓
• Manifold absolute pressure sensor (MAP) ✓
• Mass air flow sensor (MAF) ✓
• Air intake temperature sensor. ✓
(Any 3 x 1) (3)
10.4 Function of knock sensor:
• Senses engine knock. ✓
• Sends signal to the ECU. ✓ (2)
Copyright reserved Please turn over
Mechanical Technology: Automotive 18 DBE/November 2024
NSC – Marking Guidelines
10.5 Components of Distributorless Ignition System (DIS):
• ECU ✓
• Integrated coil ✓
• Spark plug ✓
• Ignition switch ✓
• Crankshaft position sensor ✓
(Any 2 x 1) (2)
10.6 Catalytic convertor:
• Oxidation ✓
• Reduction ✓ (2)
10.7 Functions of the speed control system:
• Controls the throttle opening electronically. ✓
• Keeps the vehicle at a constant speed. ✓ (2)
10.8 Alternator:
10.8.1 Labels:
A. Pulley ✓
B. Front bracket/Front cover/housing ✓
C. Bearing ✓
D. Stator ✓ (4)
10.8.2 Rotor:
• Contains the slip rings ✓ which provides a movable electrical
connection. ✓
• Induces current ✓ flow into the stator. ✓
• To create a rotating ✓ magnetic field/electromagnet. ✓
(Any 1 x 2) (2)
10.8.3 Regulator:
• Controls voltage ✓
• Controls current flow ✓
(Any 1 x 1) (1)
10.8.4 Function of the rectifier:
Converts the AC ✓ to DC. ✓ (2)
Copyright reserved Please turn over
Mechanical Technology: Automotive 19 DBE/November 2024
NSC – Marking Guidelines
10.9 Injector:
• The fuel pressure at the injector ✓
• Injection duration ✓
• Size of the injector nozzle hole/orifice ✓
• Throttle position ✓
• Amount of atmospheric pressure ✓
• Ambient temperature ✓
• Air-fuel ratio ✓
• Engine load ✓
• Engine speed (RPM) ✓
• Fuel type ✓
• Engine temperature✓
• Fuel temperature✓
(Any 3 x 1) (3)
[32]
TOTAL: 200
Copyright reserved
Study this subject
Recommended for this subject
%20Eng--5d2e2bd0-b02f-4218-849f-e7933bc6c4d1/v1-2dba8a1dc6758c98b205/card.webp)
Question paper
Mechanical Technology Grade 12 November 2024 NSC QP (Eng)
%20Afr--1e7205e4-aef1-4cc4-afdf-aac93562ae67/v1-094abcfa5c3eff1cb995/card.webp)
Question paper
Mechanical Technology Grade 12 November 2024 NSC QP (Afr)
%20Eng--10859467-be3e-41fb-aee0-b797c385437d/v1-986e8982bfb6b966a34d/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2024 QP (Eng)

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo
%20GR12%20MEMO%20SEPT2023_English_hlayiso.com_--dfc975c1-e179-4741-8d4f-e3b20c744c7e/v1-c61c66086bf36fcf31e0/card.webp)
Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo
More from Grade 12 Mechanical Technology

Annual teaching plan
Gr 12 Weld Met ATP 2023 24

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2023 Memo

Question paper
Mechanical Technology Grade 12 Eastern Cape Mock 2023 QP
%20Afr_hlayiso.com_--7d638feb-7218-4b3c-9f4c-ce95803d6e4f/v1-e8a08d94a30d7d50ccd0/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2023 QP (Afr)
%20Eng_hlayiso.com_--1523a16f-2012-4f13-a922-86cbb5900666/v1-5068227f3cbbba17b78f/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2023 QP (Eng)
%20Afr_hlayiso.com_--8d31d25d-e192-4aa9-b448-efab233391a1/v1-28cf2259fca9bcde2f63/card.webp)
Question paper