Gr 10 Mech Tech Aut ATP 2023 24

2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 (TERM 1) TERM 1 WEEK 1 WEEK 2 WEEK 3 WEEK 4 WEEK 5 WEEK 6 WEEK 7 WEEK 8 WEEK 9 WEEK 10 WEEK 11 CAPS TOPICS SAFETY (GENERIC) TOOLS (GENERIC) TOOLS (GENERIC) TOOLS & ENGINES ENGINES ENGINES ENGINES PAT REVISION REVISION EQUIPMENT (SPECIFIC) (SPECIFIC) (SPECIFIC)) (SPECIFIC) CONSOLIDATION ASSIGNMENT ASSIGNMENT (GENERIC) TOPICS/ First Aid HIV/Aids Basic tools and Application of Understand the Identification and Operating principles Operating principles Conventional layouts: Completion of PAT CONCEPTS, awareness equipment: measuring and OHS Act Learners function of engine of 4 stroke internal of 2 stroke internal • Engine in front with that was done SKILLS AND Understand the • Spanners: Ring-, marking-off must be fully aware components: combustion engines. combustion engines. front- and rear-wheel throughout term 1 VALUES OHS Act flat- and combination instruments: of all the safety Pistons, piston rings, (single cylinder spark (single cylinder spark drives Safety precautions • Steel rule precautions when crankshaft, ignition engines only): ignition engines only): • Sockets and using the following connecting rod, • Engine at rear with taken into account accessories • Square • Stroke • Stroke rear-wheel drive during performance- tools: bearings, gudgeon • Pliers • Scriber pin, camshaft, valves, • Dead centre • Dead centre • Advantages and based activities in • Compressors order to avoid injuries • Hammers • Tape measure flywheel, cylinder • Cycle • Cycle disadvantages of • Fire extinguisher head, engine block, each position or incidents) • Chisels, hacksaws • Combination set Comparison of 4- Learners must be • Lifts, jacks & oil pump, manifolds, stroke and 2-stroke fully aware of all the • Screwdrivers • Punches trestles carburettors, etc. cycle safety precautions • Allen keys when using the • Stocks & dies following tools: • Files • Hand tools • Pedestal drill • Bench grinder REQUISITE PRE- HIV/Aids safety in general and basic hand tools KNOWLEDGE RESOURCES OHS Act, safety OHS Act, safety Tools and equipment as mentioned above Engines assemblies, Engines assemblies, Engines with the Vehicles with (OTHER THAN signs in workshop, signs in workshop, YouTube videos, etc. YouTube videos, etc. above-mentioned different TEXTBOOK) TO first aid manuals & first aid manuals & components, layouts, ENHANCE hand tools & hand tools & YouTube videos, YouTube LEARNING equipment equipment etc. videos INFORMAL Use the marking-off Identify safe and Use a dismantled Investigate the Investigate the ASSESSMENT: instruments to mark- hazardous acts and engine to identify operation of a 4- operation of a 2- REMEDIATION off a plate (at least 5 conditions (e.g. various components stroke engine stroke engine ASSESSMENT mm thick) with 5 speed of emery and their functions Identify the stroke, Comparison of 4- holes. wheels, maximum dead centre and stroke and 2-stroke lift on hydraulic cycle cycle equipment, SBA & PAT PAT phase 1 (FORMAL) Assignment Downloaded from hlayiso.com 1

2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 (TERM 2) TERM 2 WEEK 1 WEEK 2 WEEK 3 WEEK 4 WEEK 5 WEEK 6 WEEK 7 WEEK 8 WEEK 9 WEEK 10 WEEK 11 CAPS TOPICS JOINING JOINING JOINING FORCES (GENERIC) FORCES (GENERIC) MAINTENANCE MAINTENANCE MAINTENANCE PAT REVISION AND REVISION AND METHODS METHODS METHODS (GENERIC) (GENERIC) (GENERIC) CONSOLIDATION ASSESSMENT ASSESSMENT (GENERIC) (GENERIC) (GENERIC) (CONTROLLED (CONTROLLED TEST) TEST) TOPICS/ Calculations on the Semi-permanent Semi-permanent Forces: Different Moments: Moments Properties of Friction: Lack of maintenance Completion of PAT CONCEPTS, size of drills and key joining methods: joining methods: types of forces found found in engineering lubricants: • Definition on equipment that was done SKILLS AND dimensions: • Bolts • Keys – in engineering components (basic • Viscosity • Excessive wear throughout term 2 VALUES components: calculations) • Causes • Drill sizes for • Studs Identification, fitting • Pour point, etc. • Overheating/seizing screw cutting and uses of the • Pulling force Definition: Moment = • Advantages • Locking devices Grading of oil and distortion • Width, thickness following types: (tensile) force x perpendicular • Application • Nuts distance (spanner according to viscosity • Failure and length of keys - Parallel key • Compressive force (SAE standards): Define the following • Split pins used to tighten a nut types of - Taper key • Shearing force or bolt) • Transmission oil • Rivets maintenance: - Gib-head key • Engine oil • Preventive - Woodruff key • Differential oil • Predictive • Cutting fluid • Reliability centred • Grease maintenance REQUISITE PRE- Grade 9 Forces KNOWLEDGE RESOURCES Bolt, nuts, etc. as Bolt, nuts, etc. Testing equipment Testing equipment Different types of Instructional videos, Instructional videos, (OTHER THAN mentioned above as mentioned to demonstrate to demonstrate oils Instructional YouTube videos, YouTube videos, etc. TEXTBOOK) TO Instructional videos, above different types of different types of videos, YouTube etc. Old question papers ENHANCE YouTube videos, Instructional forces forces videos, etc. Old question papers LEARNING etc. videos, YouTube Calculators Calculators videos, etc. INFORMAL Inspect and predict Analyse and predict ASSESSMENT: the outcome of the the outcome of the ASSESSMENT REMEDIATION lack of maintenance lack of maintenance on equipment used on equipment used in the workshop in the workshop SBA & PAT PAT Phase 2 (FORMAL) Controlled test Downloaded from hlayiso.com 2

2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 (TERM 3) TERM 3 WEEK 1 WEEK 2 WEEK 3 WEEK 4 WEEK 5 WEEK 6 WEEK 7 WEEK 8 WEEK 9 WEEK 10 WEEK 11 CAPS TOPICS TERMINOLOGY (SPECIFIC) DRIVE TRAINS MAINTENANCE (SPECIFIC) SYSTEMS & CONTROL (SPECIFIC) CONSOLIDATION REVISION AND ASSESSMENT OF PAT (CONTROLLED TEST) TOPICS/CONCEPTS, Function, Identify the various Function, Lubricatio Oil filtration Cooling systems Basic Hydraulic brake Completion of PAT SKILLS AND construction and components of the construction and n systems systems: Full- • Direct air carburetion system that was done VALUES operation of the constant mesh operation of drive • Splash feed, pressure flow and by- • Function of a • Master cylinder throughout term 3 single-plate clutch manual gearbox shafts: pass systems • Indirect air cooling and phase 4 PAT feed and full pressure carburettor (function) assembly: and define the • The slip joint feed Temperature Components function, operation • Basic principle of • Wheel cylinders • Flywheel • Universal joint Oil control: Radiators, radiator operation, etc. and power flow of: pressure cap, water Hydraulic brake • Diaphragm pressure • Constant • Oil purity, oil dilution, • Factors system: plate • Gears generating heat pumps, thermostat, velocity joint crankcase ventilation by-pass system, etc. Air filters • Disc brake assembly • Clutch plate • Shafts • Flexible coupling Purpose and types • Brake shoe assembly • Clutch couplings, etc. • Synchronising unit • Selector mechanism • Hand brake • Hydraulic: Master & assembly slave cylinders, pipes • Fault finding RESOURCES Clutch components Manual gearboxes Drive shafts and Engines with Vehicle or running Vehicle or running Carburettors, air Braking systems (OTHER THAN (as above) and components components (as different lubrication engines engines to do filters, hand tools & components, hand TEXTBOOK) TO YouTube, CDX (as above) above) with relative systems YouTube, CDX pressure testing educational videos tools & ENHANCE educational videos, YouTube, CDX specifications Hand tools educational videos and for servicing educational videos LEARNING etc. educational videos, YouTube, CDX etc. educational videos, etc. INFORMAL Check and maintain Demonstrate Practical Group ASSESSMENT: fluid levels: knowledge of the • Do a visual inspection on a cooling system Practical: REMEDIATION • Brake fluid working principle of Replace front brake a multi-speed • Do a pressure test ASSESSMENT pads and bleed the manual gearbox Check and maintain all fluid levels system including condition • Water report • Oil SBA & PAT PAT Phase 3 (FORMAL) Controlled test Downloaded from hlayiso.com 3

2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 2023/24 ANNUAL TEACHING PLANS: MECHANICAL TECHNOLOGY (AUTOMOTIVE): GRADE 10 (TERM 4) TERM 4 WEEK 1 WEEK 2 WEEK 3 WEEK 4 WEEK 5 WEEK 6-10 CAPS TOPICS SYSTEMS & CONTROL (SPECIFIC) REVISION OF TERM 1 AND 2 TOPICS REVISION OF TERM 3 AND 4 TOPICS EXAMINATION TOPICS Electricity: • Characteristics of magnetism • Use of the multi-meter • Safety • Terminology drive trains /CONCEPTS, • Electron theory – basic electrical • Electromagnets • Basics series and parallel circuits • Tools • Maintenance specific SKILLS AND principles: VALUES • Ohm’s law • Battery – lead acid type • Engines • Systems & control (carburation and - Electron movement • Electrical units and measurements: • Joining methods hydraulic brake system) - Electrons and conductors - Volts • Forces • Systems & control (electricity) - Pulse with modulation - Amps • Maintenance generic - Digital & analogue signal - Ohms - Effects of electricity RESOURCES Instructional videos, YouTube videos, etc. Multi-meters, batteries, instructional (OTHER THAN videos, YouTube videos, etc. TEXTBOOK) TO ENHANCE LEARNING INFORMAL • Competence in the use of the multi-meter . ASSESSMENT: • Taking of basic measurements ASSESSMENT REMEDIATION SBA & PAT PAT Phase 4 (FORMAL) Final examination Downloaded from hlayiso.com 4