Downloaded from hlayiso.com
NATIONAL
SENIOR CERTIFICATE
GRADE 12
SEPTEMBER 2024
ELECTRICAL TECHNOLOGY: POWER SYSTEMS
MARKS: 200
TIME: 3 hours
This question paper consists of 17 pages, including a 2-page formula sheet.
Hosted by www.ecexams.co.za.
Skip to contentAll 2024 papers 


%20Eng--2b227e9b-0513-468e-8b1a-d4df808071cd/v1-4a42676d26de4662555c/card.webp)


View all
%20MEMO%20GR12%20SEPT%202025%20ENG_watermark--0a867070-2654-43cf-8e48-5037555e0c3d/v1-84a07d81399f5d7a195b/card.webp)
%20(English)%20June%202025%20Possible%20Answers--4302563e-89b7-4f54-8a21-63b2020e985f/v1-3e4c5b36e08cde219ac2/card.webp)
%20MG%20Afr--3b862a0c-6a87-4296-b5b6-09b072c7d1e9/v1-66d030d2505ce0cce42c/card.webp)


Electrical Technology Grade 12 Eastern Cape Prelim 2024 QP
Grade 12 Electrical Technology question paper from the Eastern Cape Prelim Exam 2024 (English), 17 pages. Read online or download the free PDF.
Electrical Technology · Grade 12 · Eastern Cape Prelim Exam · 2024 · English. Question paper, 17 pages. Read online or download the PDF.
- Subject
- Electrical Technology
- Grade
- Grade 12
- Language
- English
- Document type
- Question paper
- Year
- 2024
- Exam period
- Eastern Cape Prelim Exam
- Curriculum
- CAPS
- Pages
- 17
- File size
- 1.3 MB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 17
This exam
Document textSearch extracted text and jump to a page.
Downloaded from hlayiso.com
2 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
INSTRUCTIONS AND INFORMATION
1. This question paper consists of SEVEN questions.
2. Sketches and diagrams must be large, neat and fully labelled.
3. Show ALL calculations and round off the answer correctly to TWO decimal
places. Show the units for ALL answers of calculations.
4. Number the answers correctly according to the numbering system used in
this question paper.
5. You may use a non-programmable calculator.
6. Show the units for ALL answers of calculations.
7. A formula sheet is provided at the end of this question paper.
8. Write neatly and legibly.
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 3
QUESTION 1: MULTIPLE-CHOICE QUESTIONS
Various options are given as possible answers to the following questions. Choose
the answer and write only the letter (A–D) next to the question numbers (1.1 to 1.15)
in the ANSWER BOOK, for example 1.16 D.
1.1 The layer(s) of the skin that is/are affected by a third-degree burn would
be …
A the outer layer.
B the second layer.
C all layers of skin.
D None of the above-mentioned. (1)
1.2 The phase angle of the current in a predominantly inductive, RLC circuit
is …
A leading.
B lagging.
C in phase.
D zero. (1)
1.3 The opposition by a capacitor against the flow of alternating current in a RLC
circuit is the …
A inductive reactance.
B impedance.
C capacitive reactance.
D inductance. (1)
1.4 A RLC circuit has a maximum impedance and a minimum current during …
resonance.
A series
B parallel
C the frequencies before
D the frequencies after (1)
1.5 Self-contained units controlled from the main control centres are called …
A switchgear.
B distribution networks.
C substations.
D power stations. (1)
1.6 A step-down transformer is used to …
A increase the power.
B decrease the power.
C decrease the voltage
D increase the voltage. (1)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
4 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
1.7 A three-phase system is generated when three coils are placed 120° apart
and rotated in a …
A uniform magnetic field.
B vacuum.
C triangle.
D All the above-mentioned. (1)
1.8 A delta-star transformer is used …
A mainly in heavy industries where a high-power transfer is essential.
B as a step-down transformer in high voltage supply lines.
C mainly for interior wiring of premises.
D extensively in distribution systems where a four-wire system is required. (1)
1.9 Air Natural (AN) is a cooling method used for …
A dry transformers.
B oil immersed transformers.
C relays.
D contactors. (1)
1.10 The purpose of a no-volt relay is to ...
A allow a motor to automatically start after a power failure is restored.
B increase the voltage of a three-phase motor.
C prevent a motor from automatically starting when a power failure is
restored.
D monitor the amount of current drawn by a motor. (1)
1.11 The start button used in a motor control circuit is …
A normally open pushbutton.
B open-relay contact.
C normally closed pushbutton.
D closed-relay contact (1)
1.12 … helps avoid cogging and reduces magnetic hum.
A An armature
B A skewed rotor
C The stator
D A cooling fan (1)
1.13 An example of a PLC output is a …
A normally open contact.
B motor.
C sensor.
D marker or flag. (1)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 5
1.14 A PLC’s hardware is …
A all the physical parts and components that make up the device.
B the machine language that is installed on a computer.
C the plc processor.
D Both A and C. (1)
1.15 … detect the presence of metal objects and whether they are ferrous or
nonferrous.
A Capacitive proximity sensors
B Inductive proximity sensors
C Ultrasonic proximity sensors
D All the above (1)
[15]
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
6 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
QUESTION 2: OCCUPATIONAL HEALTH AND SAFETY
2.1 Explain why the misuse of equipment in a workshop is considered an unsafe
act. (2)
2.2 State TWO recommended ways to stop bleeding. (2)
2.3 Write down any TWO standard treatments for shock. (2)
2.4 Define a medical emergency. (2)
2.5 List ONE unsafe condition that must be avoided in a workshop. (1)
2.6 Name ONE important personal protection item used when working with
chemicals. (1)
[10]
QUESTION 3: RLC CIRCUITS
3.1 State the phase relationship between the current and voltage in a pure
capacitive AC circuit. (1)
3.2 Define the following with reference to RLC circuits connected across an
alternating voltage supply.
3.2.1 Phasor diagram (2)
3.2.2 Resonant frequency (2)
3.3 A series circuit with resistance of 600 Ω, inductance 100 mH and capacitance
4 µF is connected across a 120 V / 60 Hz supply.
Given:
R = 600 Ω
L = 100 mH
C = 4 µF
VS = 120 V
F = 60 Hz
Calculate:
3.3.1 The reactance of the inductor (3)
3.3.2 The reactance of the capacitor (3)
3.3.3 The circuit impedance (3)
3.3.4 The circuit current (3)
3.5 Find the resonant frequency of a circuit with a 100 mH coil connected in series
with a 0,022 µF capacitor. (3)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 7
3.6 Refer to FIGURE 3.6 below and answer the questions that follow.
FIGURE 3.6: PARALLEL RLC CIRCUIT
Given:
IC = 4 A
IL = 6 A
IR = 4 A
3.6.1 Calculate the total current. (3)
3.6.2 Calculate the phase angle. (3)
3.6.3 Draw a labelled phasor diagram for FIGURE 3.6. (3)
3.6.4 Motivate, with a reason, if the circuit is predominantly capacitive or
inductive. (3)
3.7 State THREE conditions that will occur if the power factor is at unity in a RLC
series circuit. (3)
[35]
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
8 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
QUESTION 4: THREE-PHASE AC GENERATION
4.1 State THREE disadvantages of a three-phase generation in comparison
with a single-phase generation. (3)
4.2 Explain the term apparent power. (1)
4.3 Name the THREE network stages of the national power grid in the
CORRECT order. (3)
4.4 A three-phase generator delivers power to a star-connected load. The
phase voltage of the load is 230 V with a line current of 35 amperes. The
phase angle is 18°.
Given:
VPH = 230 V
IL = 35 A
θ = 18°
Calculate the following:
4.4.1 The line voltage (3)
4.4.2 The apparent power (3)
4.4.3 The reactive power (3)
4.4.4 The true power (3)
4.5 Two watt-meters indicate 10 kW and 3 kW respectively when they are
connected to measure the input power to the load. Calculate the total
power in kW.
Given:
W1 = 10 kW
W2 = 3 kW (3)
4.6 Name ONE application of a wattmeter in three-phase AC systems. (1)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 9
4.7 FIGURE 4.7 below shows an analogue power factor meter. Answer the
questions that follow.
FIGURE 4.7: POWER FACTOR METER
4.7.1 Does the reading show a leading or lagging power factor? (1)
4.7.2 State the cause of this type of reading. (1)
4.7.3 State how the meter reading could be brought closer to unity. (1)
4.8 Explain the effect of stepping up the voltage in transmission lines. (2)
4.9 State TWO quantities, other than power, that can be determined by using (2)
the two-wattmeter method.
4.10 Explain how copper losses are reduced in overhead transmission lines. (2)
4.11 Briefly explain why the generated electricity is lower at the point of
distribution than at the point of generation. (2)
4.12 State the function of a kilowatt-hour meter. (1)
[35]
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
10 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
QUESTION 5: THREE-PHASE TRANSFORMERS
5.1 Compare three single-phase transformers with a three-phase transformer if
they supply the same three-phase load. Refer to the following factors:
5.1.1 Economic cost (1)
5.1.2 Efficiency (1)
5.2 Name TWO cooling methods used in a dry transformer. (2)
5.3 State the main cause that contributes to heat generation in transformers. (1)
5.4 State TWO safety precautions when working with transformers. (2)
5.5 Name TWO physical characteristics of a three-phase shell-type transformer. (2)
5.6 Name TWO of the most common internal failures of three-phase (2)
transformers.
5.7 FIGURE 5.7 below is a diagrammatic representation of a three-phase
transformer connection. Answer the questions that follow.
FIGURE 5.7
5.7.1 Identify the type of transformer connection in FIGURE 5.7. (1)
5.7.2 Name TWO applications of the transformer in FIGURE 5.7. (2)
5.7.3 State, with a reason, whether the transformer is a step-up or step-
down transformer. (2)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 11
5.8 Refer to the circuit diagram in FIGURE 5.8 below and answer the questions
that follow.
FIGURE 5.8: TRANSFORMER CONNECTION
Given:
S = 200 kVA
VLP = 11 kV
VLS = 380 V
ILP = 10,5 A
PIN = 171,8 kW
cosθ = 0,85
VPHS = 219,39 V
Calculate the:
5.8.1 Efficiency of the transformer if it operates at a power factor of 0,85
lagging (5)
5.8.2 Turns ratio (3)
5.8.3 Secondary line current of the transformer (3)
5.9 Explain why a transformer only operates with an AC supply. (3)
[30]
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
12 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
QUESTION 6: THREE-PHASE MOTORS AND STARTERS
6.1 Name THREE mechanical inspections that could be carried out on the rotor
and bearings of a motor. (3)
6.2 Name TWO continuity tests to be performed on a three-phase motor. (2)
6.3 State TWO applications of squirrel-cage induction motors where constant
speed and torque is essential. (2)
6.4 Differentiate between synchronous speed and rotor speed. (2)
6.5 FIGURE 6.5 below shows the rotor of an induction motor. Answer the
questions that follow.
FIGURE 6.5
6.5.1 Name parts A and B. (2)
6.5.2 State ONE important advantage of using this type of a rotor
compared to using a motor with brushes and slip rings. (1)
6.5.3 Give ONE reason why the rotor bars are skewed. (1)
6.6 A three-phase induction motor with 6 pole pairs per phase is connected to a
380V/50Hz supply and has a slip of 0,05 units.
Given:
p=6
f = 50 Hz
s = 0,05 units
V = 380 V
Calculate the following:
6.6.1 Synchronous speed (3)
6.6.2 Rotor speed (3)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 13
6.7 TABLE 6.7 below shows the name plate of a three-phase induction motor.
Answer the questions that follow.
MOTOR MANUFACTURER SPECIFICATION
Phase 3
Voltage 380 V
Current 1,3 A
Speed 1 500 r/min
Power 7,5 kW
Frequency 50 Hz
Cos 𝜃 0,8 lagging
Frame No 22SP27
TABLE 6.7: NAME PLATE OF A THREE-PHASE INDUCTION MOTOR
6.7.1 State the amount of current the motor will draw from the supply at full
load. (1)
6.7.2 Explain why the motor is suitable for use in South Africa. (2)
6.7.3 State what the 7,5 kW on the name plate indicates. (1)
6.7.4 Determine the total number of poles. (5)
6.7.5 Calculate the efficiency of the motor at full load if the total loss is
1,2 kW. (5)
6.8 Explain how the direction of rotation of a three-phase induction motor can be
changed. (2)
[35]
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
14 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
QUESTION 7: PROGRAMMABLE LOGIC CONTROLLERS
7.1 List THREE safety precautions to be considered when connecting a PLC to
the supply. (3)
7.2 State THREE important hardware components of a PLC. (3)
7.3 Describe the following terms with reference to a PLC:
7.3.1 Hardware (2)
7.3.2 Software (3)
7.3.3 Opto-coupler (3)
7.4 FIGURE 7.4 below shows the control circuit of a direct-on-line (DOL)
starter. Design a PLC ladder logic that will execute the same function.
FIGURE 7.4: CONTROL CIRCUIT OF A DIRECT-ON-LINE STARTER (6)
7.5 Name TWO components used in the output module of a PLC to drive a high
current inductive load. (2)
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 15
7.6 FIGURE 7.6 below shows the different stages in a variable speed drive.
Answer the questions that follow.
FIGURE 7.6: VARIABLE SPEED DRIVE STAGES
7.6.1 Identify stage A. (1)
7.6.2 Name a semiconductor component that could replace the switches
used at A. (1)
7.6.3 State TWO advantages of using variable speed drives. (2)
7.6.4 Describe vector drives as a method of speed control. (3)
7.7 Explain the difference between an analogue signal and a digital signal. (2)
7.8 Draw a fully labelled diagram of a PLC scan cycle. (3)
7.9 With reference to sensors:
7.9.1 Explain the term sensor. (2)
7.9.2 Name TWO types of sensors other than a proximity sensor. (2)
7.9.3 State TWO uses of a proximity sensor. (2)
[40]
TOTAL: 200
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
16 ELECTRICAL TECHNOLOGY (POWER SYSTEMS) (EC/SEPTEMBER 2024)
FORMULA SHEET
RLC-CIRCUITS THREE-PHASE AC GENERATION
X L = 2πfL and XC = 2πfC
1 STAR
1 V VL = √3 × VPH and VPH = IPH × ZPH
fr = 2π√LC and I = R
IL = IPH
𝑃 = 𝑉𝐼 cos 𝜃
DELTA
SERIES
VL = VPH and VPH = IPH × ZPH
IT = IR = IL = IC
IL = √3 × IPH
Z = √R2 + (XL − XC )2
POWER
VL = I × XL and VC = I × XC
S = √3VL IL
VT = IZ and
Q = √3VL IL sin θ
𝑉𝑇 = √𝑉𝑅 2 + (𝑉𝐿 − 𝑉𝐶 )2
P = √3VL IL cos θ
R VR
cos θ = Z and cos θ = V
T
P = S cos θ
X X V V 1 L
Q = ZL = ZC = VL = VC = R √C cos θ = S
P
S S
PARALLEL 𝑜𝑢𝑡𝑝𝑢𝑡
ƞ = 𝑖𝑛𝑝𝑢𝑡 × 100%
VS = VR = VL = VC POUTPUT
ƞ=P × 100
OUTPUT +losses
VR
IR = R
TWO-WATTMETER METHOD
VL VC
IL = X and IC = X
L C PT = W1 + W2
W −W
IT = √IR 2 + (IL − IC )2 tanθ = √3 (W1+W2)
1 2
V THREE-WATTMETER METHOD
Z=I
T
PT = W1 + W2 + W3
IR
cos θ = I
T
X X V V 1 L
Q = ZL = ZC = VL = VC = R √C
S S
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Downloaded from hlayiso.com
(EC/SEPTEMBER 2024) ELECTRICAL TECHNOLOGY (POWER SYSTEMS) 17
FORMULA SHEET
THREE-PHASE TRANSFORMERS THREE-PHASE MOTORS AND STARTERS
STAR STAR
VL = √3 × VPH and IL = IPH VL = √3 × VPH and IL = IPH
DELTA DELTA
VL = VPH and IL = √3 × IPH VL = VPH and IL = √3 × IPH
POWER POWER
𝑆 = √3𝑉𝐿 𝐼𝐿 𝑆 = √3𝑉𝐿 𝐼𝐿
𝑄 = √3𝑉𝐿 𝐼𝐿 𝑠𝑖𝑛 𝜃 𝑄 = √3𝑉𝐿 𝐼𝐿 𝑠𝑖𝑛 𝜃
𝑃 = √3𝑉𝐿 𝐼𝐿 𝑐𝑜𝑠 𝜃 𝑃 = √3𝑉𝐿 𝐼𝐿 𝑐𝑜𝑠 𝜃
𝑃 = 𝑆 𝑐𝑜𝑠 𝜃 𝑃 = 𝑆 𝑐𝑜𝑠 𝜃
𝑃 𝑃
𝑐𝑜𝑠 𝜃 = 𝑆 𝑐𝑜𝑠 𝜃 = 𝑆
𝑃𝑜𝑢𝑡𝑝𝑢𝑡
ƞ= × 100%
𝑃𝑜𝑢𝑡𝑝𝑢𝑡 𝑃𝑖𝑛𝑝𝑢𝑡
ŋ=𝑃 × 100%
𝑜𝑢𝑡𝑝𝑢𝑡 + 𝑙𝑜𝑠𝑠𝑒𝑠
MOTOR SPEED
VPHP NP IPHS
T. Ratio = V =N =I
PHS S PHP 60 × f
ns = p
ns − nr
%Slip = × 100%
ns
nr = ns (1 − S)
𝑆 = n S − nR
Overload setting = 125% × rated current
Copyright reserved Please turn over
Hosted by www.ecexams.co.za.
Study this subject
Recommended for this subject

Memorandum
Electrical Technology Grade 12 Eastern Cape Prelim 2024 Memo

Memorandum
Electrical Technology Grade 12 Eastern Cape Prelim 2024 Memo

Memorandum
Electrical Technology Grade 12 Eastern Cape Prelim 2024 Memo
%20Eng--2b227e9b-0513-468e-8b1a-d4df808071cd/v1-4a42676d26de4662555c/card.webp)
Question paper
Electrical Technology Grade 12 NSC June 2024 QP (Eng)

Question paper
Electrical Technology Grade 12 Eastern Cape Mock 2023 QP

Question paper
Electrical Technology Grade 12 Eastern Cape Mock 2022 QP
More from Grade 12 Electrical Technology

Annual teaching plan
Gr 12 Dig Elec ATP 2023 24
%20MEMO%20GR12%20SEPT%202025%20ENG_watermark--0a867070-2654-43cf-8e48-5037555e0c3d/v1-84a07d81399f5d7a195b/card.webp)
Memorandum
Electrical Technology Grade 12 Eastern Cape Mock 2025 Memo
%20(English)%20June%202025%20Possible%20Answers--4302563e-89b7-4f54-8a21-63b2020e985f/v1-3e4c5b36e08cde219ac2/card.webp)
Memorandum
Electrical Technology Grade 12 P1 Gauteng June 2025 Memo
%20MG%20Afr--3b862a0c-6a87-4296-b5b6-09b072c7d1e9/v1-66d030d2505ce0cce42c/card.webp)
Memorandum
Electrical Technology Grade 12 NSC November 2025 Memo (Afr)

Memorandum
Electrical Technology Grade 12 Eastern Cape Mock 2023 Memo

Memorandum