Confidential
NATIONAL
SENIOR CERTIFICATE
GRADE 12
AGRICULTURAL TECHNOLOGY
NOVEMBER 2024
MARKS: 200
TIME: 3 hours
This question paper consists of 15 pages.
Copyright reserved Please turn over
Skip to contentAll 2024 papers 





View all





Agricultural Technology Grade 12 November 2024 NSC QP (Eng)
Grade 12 Agricultural Technology question paper from the November 2024 NSC (English), 15 pages. Read online or download the free PDF.
Agricultural Technology · Grade 12 · November 2024 NSC · 2024. Question paper, 15 pages. Read online or download the PDF.
- Subject
- Agricultural Technology
- Grade
- Grade 12
- Document type
- Question paper
- Year
- 2024
- Exam period
- November 2024 NSC
- Curriculum
- CAPS
- Pages
- 15
- File size
- 521.5 KB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 15
This exam
November NSC 2024
Document textSearch extracted text and jump to a page.
Agricultural Technology 2 DBE/November 2024
NSC Confidential
INSTRUCTIONS AND INFORMATION
1. GENERAL INSTRUCTIONS AND INFORMATION
1.1 This question paper consists of TWO sections, namely SECTION A
and SECTION B.
1.2 BOTH sections are COMPULSORY.
1.3 Answer ALL the questions in the ANSWER BOOK.
1.4 Number the answers correctly according to the numbering system
used in this question paper.
1.5 You may use a non-programmable calculator.
1.6 Show ALL calculations.
1.7 Write neatly and legibly.
2. SECTION A: SHORT QUESTIONS
2.1 This section consists of THREE questions.
2.2 Follow the instructions when answering the questions.
3. SECTION B: STRUCTURED LONG QUESTIONS
3.1 This section consists of FIVE questions.
3.2 Start EACH question on a NEW page.
Copyright reserved Please turn over
Agricultural Technology 3 DBE/November 2024
NSC Confidential
SECTION A
QUESTION 1
1.1 Various options are provided as possible answers to the following questions.
Choose the answer and write only the letter (A–D) next to the question
numbers (1.1.1 to 1.1.10) in the ANSWER BOOK, e.g. 1.1.11 D. Nov
1.1.1 A device used for determining the grazing pattern of a farm animal:
A Two-way radio
B GPS
C VRT
D RFID
1.1.2 A water purification method that sends water through two different
liquids, separated by a permeable film, that allows water to pass
through on a molecular level:
A Sand filter
B Water softener
C Carbon filter
D Reverse osmosis
1.1.3 Insufficient … will cause splattering of little metal balls during the
welding process and will discolour the welding joint into colours of
brown and green.
A wire speed
B shielding gas
C amperage
D heat
1.1.4 ONE of the following is NOT part of the three-point hitch
mechanism of a tractor:
A Levelling box
B Lifting arms
C PTO shaft
D Stabilising chains
1.1.5 Movable capital includes implements and …
A fuel.
B boreholes.
C farm tools.
D repairs.
Copyright reserved Please turn over
Agricultural Technology 4 DBE/November 2024
NSC Confidential
1.1.6 The function of the automatic depth-control mechanism of a tractor
is to adjust the …
A rear end of the plough.
B ploughing depth according to the soil conditions.
C angle of the implement in relation to the tractor's movement.
D cross angle of the implement in relation to the tractor.
1.1.7 … is any plant or animal matter that is combustible and which can
be used as an alternative fuel.
A Biofuel
B Coal
C Fossil fuel
D Petroleum
1.1.8 The process of joining brass:
A Silver soldering
B Brazing
C Plasma joining
D MIG welding
1.1.9 ONE of the following must be considered when choosing an
adhesive for application in conditions where extreme heat plays a
major role:
A Heat resistance
B Flammability
C Combustibility
D All the above-mentioned
1.1.10 … is used as a non-stick material for manufacturing windshield
wiper blades.
A Bakelite
B Teflon
C Vesconite
D PVC (10 x 2) (20)
Copyright reserved Please turn over
Agricultural Technology 5 DBE/November 2024
NSC Confidential
1.2 Change the underlined word in the following to make the statements TRUE.
Write only the appropriate word next to the question numbers (1.2.1 to 1.2.5)
in the ANSWER BOOK, e.g. 1.2.6 Tractor.
1.2.1 A spur gear runs at an angle across the outer circumference of the
gear.
1.2.2 Hydro energy is extracted from deep under the Earth's surface and
is regarded as one of the most sustainable energy sources.
1.2.3 The side of a hydraulic cylinder, which contains the piston, creates
a much weaker pushing force than the opposite side.
1.2.4 Electrical fences should not be erected diagonally under overhead
power lines.
1.2.5 A streak of lightning always finds the longest path to the ground.
(5 x 2) (10)
1.3 Choose a word/term from COLUMN B that matches a description
in COLUMN A. Write only the letter (A–I) next to the question numbers
(1.3.1 to 1.3.5) in the ANSWER BOOK, e.g. 1.3.6 J
COLUMN A COLUMN B
1.3.1 A device that produces electrical A standardisation
energy through photovoltaic
technology B wind turbines
1.3.2 An example of pneumatic C inverter
equipment used in a farm
workshop D alternator
1.3.3 A device that changes direct E solar panels
current to alternating current
F mechanisation
1.3.4 A device used to store energy
generated by a wind turbine G compressor
1.3.5 Makes it possible for spares to H battery
be purchased from any agent
instead of a specific one I anemometer
(5 x 2) (10)
TOTAL SECTION A: 40
Copyright reserved Please turn over
Agricultural Technology 6 DBE/November 2024
NSC Confidential
SECTION B
QUESTION 2: MATERIALS AND STRUCTURES
Start this question on a NEW page.
2.1 Various alloy elements have a positive influence on stainless steel.
Choose the influence on stainless steel (COLUMN B) that matches the alloy
element (COLUMN A). Write only the letter (A–E) next to the question
numbers (2.1.1 to 2.1.3) in the ANSWER BOOK, e.g. 2.1.4 F.
COLUMN A COLUMN B
ALLOY ELEMENT INFLUENCE ON STAINLESS STEEL
2.1.1 Manganese A promotes the hardening of steel
2.1.2 Nickel B enhances magnetism
2.1.3 Chromium C decreases strengths
D gives a fair amount of toughness
at low temperatures
E gives steel a coarser structure
(3 x 1) (3)
2.2 Complete the following table by choosing a word/phrase from the list below.
Write only the word/phrase next to the question numbers (2.2.1 to 2.2.6) in
the ANSWER BOOK. Each word/phrase may be used only ONCE.
hammer; soft; bronze; surface coating for food cans;
copper; silver white metal
NAME OF NON-
PROPERTY USE
FERROUS METAL
2.2.1 2.2.2 Electrical
conductors
2.2.3 Does not generate a spark when 2.2.4
struck against a hard surface
Tin 2.2.5 2.2.6
(6)
2.3 State TWO important factors that should be considered when choosing an
adhesive for a specific application. (2)
Copyright reserved Please turn over
Agricultural Technology 7 DBE/November 2024
NSC Confidential
2.4 The picture below shows a damaged fibreglass boat hull.
2.4.1 Give a reason why fibreglass is used to repair damaged boat hulls. (1)
2.4.2 List THREE items needed for personal protection that must be
used when working with fibreglass. (3)
2.4.3 Name a cleaning agent that can be used to safely remove resin or
catalyst from your skin when working with fibreglass. (1)
2.5 Give ONE use of Vesconite for EACH of the applications by choosing a term
from the list below. Write only the term next to the question numbers
(2.5.1 to 2.5.4) in the ANSWER BOOK. Each term may be used only ONCE.
centre-pivot bush; lifting arm bush; metal-to-metal bush; shackle pin bush
2.5.1 Tractors (1)
2.5.2 Wind pump (1)
2.5.3 Tractor trailers (1)
2.5.4 Irrigation equipment (1)
Copyright reserved Please turn over
Agricultural Technology 8 DBE/November 2024
NSC Confidential
2.6 The pictures below show different types of electric farm fences.
A B
2.6.1 Identify the type of electric fence shown in picture A and in
picture B. (2)
2.6.2 State an advantage of the electric fence in picture A. (1)
2.6.3 Explain why barbed or razor wire should never be used in the
construction of an electric fence. (2)
2.7 Complete the table below about specifications of electric fences. Write only
the correct answer next to the question numbers (2.7.1 to 2.7.3) in the
ANSWER BOOK.
CLEARANCE BETWEEN
PRESCRIBED VOLTAGE ELECTRIC FENCE AND
OVERHEAD POWER LINE
2.7.1 3 metre clearance
Between 1 000 and 33 000 volts 2.7.2
2.7.3 8 metre clearance
(3)
2.8 Design a neatly labelled warning sign that should be placed on an electric
fence to warn people of imminent danger. Include the required sign and
measurements on the warning sign, as stipulated by the OHS Act.
Use the following criteria:
Measurements indicating the actual size of the sign 2 marks
Labelling/Inscription 2 marks
Correct drawing on the warning plate 1 mark (5)
2.9 The energiser's earth system should be at least 5 metres away from the main
supply unit. Do you agree with this statement? Motivate your answer. (2)
[35]
Copyright reserved Please turn over
Agricultural Technology 9 DBE/November 2024
NSC Confidential
QUESTION 3: ENERGY
Start this question on a NEW page.
3.1 Name FOUR different renewable alternative energy sources that can be used
on a farm to compensate for load-shedding. (4)
3.2 The picture below shows a wind turbine.
3.2.1 Name a device that is installed on a wind turbine to direct the
turbine into the incoming wind. (1)
3.2.2 State THREE important requirements to consider before choosing
a wind turbine to generate electricity on a farm. (3)
3.2.3 State TWO factors that might cause wind turbine failure. (2)
3.3 Tabulate TWO advantages and TWO disadvantages of solar energy. (4)
3.4 The picture below shows methanol.
Methanol
CH3OH
3.4.1 Name a fuel that methanol can easily be transformed into. (1)
3.4.2 Name TWO natural sources available on a farm that can be used
to make methanol. (2)
3.5 Describe the manufacturing process of biodiesel. (3)
[20]
Copyright reserved Please turn over
Agricultural Technology 10 DBE/November 2024
NSC Confidential
QUESTION 4: SKILLS AND CONSTRUCTION PROCESSES
Start this question on a NEW page.
4.1 The picture below shows a MIG welding machine.
4.1.1 What does EACH of the letters in the abbreviation MIG represent? (3)
4.1.2 Name parts A to D of the MIG welding machine in the picture
above. (4)
4.1.3 Explain the role that gas plays in the MIG welding process. (2)
4.1.4 Explain the purpose of spot welding. (2)
4.2 Explain the effect that gravity has on the vertical up arc welding process and
name TWO methods that can be used to control this effect. (3)
4.3 What is the welding process called where worn parts of a grader blade are
built up with a wear-resistant metal? (1)
4.4 Describe the process of preparing a broken cast-iron part before the welding
process starts. (5)
4.5 State TWO types of wear that metals can be subjected to. (2)
Copyright reserved Please turn over
Agricultural Technology 11 DBE/November 2024
NSC Confidential
4.6 State the effect of EACH of the following actions when cutting with the
oxyacetylene cutting apparatus:
4.6.1 Moving the cutting torch too fast (1)
4.6.2 Moving the cutting torch too slow (1)
4.7 The picture below shows a plasma-cutting machine.
4.7.1 State TWO factors that must be considered before buying a
plasma-cutting machine. (2)
4.7.2 Name TWO gases that can be used in the plasma-cutting process
to remove the molten metal. (2)
4.7.3 Explain the plasma-cutting process. (4)
4.7.4 State THREE safety measures that must be kept in mind when
working with a plasma-cutting machine. (3)
[35]
Copyright reserved Please turn over
Agricultural Technology 12 DBE/November 2024
NSC Confidential
QUESTION 5: TOOLS, IMPLEMENTS AND EQUIPMENT
Start this question on a NEW page.
5.1 The picture below shows a baling machine that is used to make round bales.
5.1.1 Name the type of bale-forming system that is used in the picture
above. (1)
5.1.2 Describe the bale-forming process inside the baling chamber of
this type of baling machine. (5)
5.1.3 Name THREE tasks that should be performed when doing
maintenance on this type of baling machine. (3)
5.1.4 Round bales have the potential to roll down a hill. Explain TWO
safety precautions that must be kept in mind when ejecting round
bales against a slope. (2)
5.2 Complete the table below by comparing the friction clutch to the hydraulic
clutch. Write only the correct answer next to the question numbers
(5.2.1 to 5.2.4) in the ANSWER BOOK.
FRICTION CLUTCH HYDRAULIC CLUTCH
APPLICATION 5.2.1 5.2.3
LOAD CAPACITY 5.2.2 5.2.4 (4)
5.3 Give FOUR examples of irresponsible human behaviour that can cause
tractor rollovers. (4)
5.4 Explain the consequences of the following installation errors:
5.4.1 The mass of moving parts is not spread equally over the bearings
of a hammer mill (2)
5.4.2 The cyclone of the hammer mill does not hang level (2)
Copyright reserved Please turn over
Agricultural Technology 13 DBE/November 2024
NSC Confidential
5.5 Name the type of hydraulic cylinder that is installed in the power steering
system of a tractor. Motivate your answer. (2)
5.6 The diagram below shows a V-belt pulley system.
C
B
A
5.6.1 Name a device that must be installed between parts A and B to
enable them to turn as a unit. (1)
5.6.2 Calculate the speed ratio of the pulley system, if pulley B rotates at
a speed of 1 200 r/min and pulley C at a speed of 600 r/min. Show
ALL calculations. (4)
5.6.3 State THREE disadvantages of V-belts. (3)
5.7 The picture below shows a gearbox installed on a centre-pivot irrigation
system.
5.7.1 Identify the types of gears labelled A and B. (2)
5.7.2 State TWO functions of this type of gear assembly. (2)
5.7.3 Indicate which substance is used inside this gearbox to reduce
wear and friction. (1)
5.8 State TWO advantages of mechanisation in modern agriculture. (2)
[40]
Copyright reserved Please turn over
Agricultural Technology 14 DBE/November 2024
NSC Confidential
QUESTION 6: WATER MANAGEMENT
Start this question on a NEW page.
6.1 Study the pictures of two different irrigation systems below and answer the
questions that follow.
A B
6.1.1 Identify the type of irrigation system in picture A. (1)
6.1.2 Name a type of filter system that can be installed in an irrigation
system to prevent blockage of the sprayer nozzles. (1)
6.1.3 Give THREE reasons why a farmer would prefer irrigation
system A instead of irrigation system B. (3)
6.1.4 Explain the function of the down pipes connected to the
goosenecks on irrigation system B. (2)
6.2 State TWO advantages of an irrigation timer that is installed in an irrigation
system. (2)
6.3 Explain the design of a septic tank as used in a household sewage system. (5)
6.4 Design a distribution field used to evenly distribute the wastewater from a
septic tank to the absorption field.
The drawing must include the following:
Distribution box 1 mark
Measurements 1 mark
Labels 1 mark
Direction of flow 1 mark
Pipe system 1 mark (5)
Copyright reserved Please turn over
Agricultural Technology 15 DBE/November 2024
NSC Confidential
6.5 A farmworker uses a water pump to fill a water tank. The water tank has a
capacity of 10 000 litres. It takes 1 hour 20 minutes to fill the tank.
Use the following formula to calculate the flow rate of the water through the
system.
Formula: Flow rate = Content
Time (3)
6.6 The pictures below show various components found in an irrigation system.
A B
C D
6.6.1 Name TWO different systems that can be used to connect the
motor in picture A to the centrifugal pump in picture B. (2)
6.6.2 Picture C shows a dripper that is used in a drip irrigation system.
Name FOUR disadvantages of this type of irrigation system. (4)
6.6.3 Picture D shows an inline water filter that uses a sieve to filter
impurities from the water. Name TWO other water filtration
methods that can be used to filter irrigation water. (2)
[30]
TOTAL SECTION B: 160
GRAND TOTAL: 200
Copyright reserved
Study this subject
Recommended for this subject

Memorandum
Agricultural Technology Grade 12 November 2024 NSC Memo

Memorandum
Agricultural Technology Grade 12 November 2024 NSC Memo

Memorandum
Agricultural Technology Grade 12 NSC June 2024 Memo (Afr)

Memorandum
Agricultural Technology Grade 12 NSC June 2024 Memo (Eng)

Question paper
Agricultural Technology Grade 12 NSC June 2023 QP (Eng)

Question paper
Agricultural Technology Grade 12 NSC June 2023 QP (Afr)
More from Grade 12 Agricultural Technology

Annual teaching plan
Gr 12 Agric Tech ATP 2023 24

Memorandum
Agricultural Technology Grade 12 NSC June 2025 Memo (Afr)

Memorandum
Agricultural Technology Grade 12 NSC November 2025 Memo

Memorandum
Agricultural Technology Grade 12 NSC November 2025 Memo

Memorandum
Agricultural Technology Grade 12 NSC June 2023 Memo (Afr)

Memorandum