Mechanical Technology PAT GR 12 2021 (Fitting and Machining) Eng

Downloaded from hlayiso.com MECHANICAL TECHNOLOGY (FITTING AND MACHINING) GUIDELINES FOR PRACTICAL ASSESSMENT TASKS GRADE 12 2021 These guidelines consist of 24 pages. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 2 DBE/PAT 2021 NSC TABLE OF CONTENTS PAGE 1. INTRODUCTION/BACKGROUND 3 2. TEACHER GUIDELINES 4 2.1 Administration of the PAT 4 2.2 Assessment of the PAT 4 2.3 Moderation of the PAT 4 2.4 Consequences of absence/non-submission of tasks 4 2.5 Declaration of Authenticity 5 3. LEARNER GUIDELINES 6 Instructions to the learner 6 4. SPECIALISATION 7 FITTING AND MACHINING 7 Rubrics 16 Mark sheets 18 5. CONCLUSION 24 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 3 DBE/PAT 2021 NSC 1. INTRODUCTION/BACKGROUND The 18 Curriculum and Assessment Policy Statements subjects which contain a practical component all include a practical assessment task (PAT). These subjects are:  AGRICULTURE: Agricultural Management Practices, Agricultural Technology  ARTS: Dance Studies, Design, Dramatic Arts, Music, Visual Arts  SCIENCES: Computer Applications Technology, Information Technology, Technical Sciences, Technical Mathematics  SERVICES: Consumer Studies, Hospitality Studies, Tourism  TECHNOLOGY: Mechanical Technology, Civil Technology, Electrical Technology, and Engineering Graphics and Design A practical assessment task (PAT) mark is a compulsory component of the final promotion mark for all candidates offering subjects that have a practical component and counts 25% (100 marks) of the end-of-year examination mark. The PAT is implemented across the first three terms of the school year. This is broken down into different phases or a series of smaller activities that make up the PAT. The PAT allows for learners to be assessed on a regular basis during the school year and it also allows for the assessment of skills that cannot be assessed in a written format, e.g. test or examination. It is therefore important that schools ensure that all learners complete the practical assessment tasks within the stipulated period to ensure that learners are resulted at the end of the school year. The planning and execution of the PAT differs from subject to subject. The PAT allows the teacher to directly and systematically observe applied competence. The PAT comprises the application/performance of the knowledge, skills and values particular to that subject and counts 25% of the total promotion/certification mark out of 400 for the subject. The PAT is implemented across the first three terms of the school year. Any profession requires of its members a thorough grounding in both theory and practice and MECHANICAL TECHNOLOGY is no exception. It is emphasized that the goal of the practical assessment task is to produce a skilled learner in each specialisation field. A nation's true wealth is in its manpower and education that should aim to develop the talents of a learner so that he/she can contribute to the well-being of the society by using and developing scientific and technological resources. To prepare a learner in MECHANICAL TECHNOLOGY'S specialisation fields, one must focus on the following:  An attitude where the learner can selectively use ideas, gather evidence and facts, to drawing logical conclusions to put them to good use creatively and with imagination;  A capability to express ideas and information clearly by speech, writing, drawing and manufacturing and  A willingness and capability to accept and exercise responsibility, to make decisions, and to learn by experience. Attributes such as these cannot all be achieved in a classroom. A sound knowledge of engineering sciences is essential to equip the MECHANICAL TECHNOLOGY learner with the necessary practical capabilities for the required processes. Practical training is the application of acquiring essential skills to bridge between trade theory and practice. Practical application in the workshop must therefore be made an interesting and challenging experience to develop the learner physically and mentally. The learner must show his/her initiative, curiosity and persistence in learning. In order to stimulate and develop self- confidence the granting of some degree of responsibility during the practical application is very important. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 4 DBE/PAT 2021 NSC 2. TEACHER GUIDELINES 2.1 Administration of the PAT Teachers are requested to make copies of the different specialisation PAT documents. These documents need to be handed out to the learners at the beginning of the year. The Practical Assessment Task for Grade 12 is externally set, internally assessed and externally moderated. Teachers must attach due dates for the different facets of the PAT (refer to the CAPS document). In this manner, learners can easily assess their progress. Instances where formal assessments take place, it is the responsibility of the teacher to administer assessment. The PAT should be completed within the first three terms. The PAT should be completed under controlled conditions. (Refer to Mechanical Technology SPECIALISATION: CAPS Grades 10–12.) 2.2 Assessment of the PAT Frequent and developmental feedback is needed to ensure necessary guidance and support to the learner. Both formal and informal assessment should be conducted to ensure that the embedded skills are developed. Informal assessment can be conducted only to monitor progress of the learner. Formal assessment should always be conducted and recorded by the teacher. 2.3 Moderation of the PAT The tasks, projects, assessment criteria as well as the mark sheets must be presented to the moderator during moderation of the PAT. The moderator should be able to call on a learner to explain and demonstrate the functions, principles and skills during the moderation purposes. On completion the moderator will, if necessary, adjust the marks of the group up or downwards depending on the decision reached as a result of moderation. 2.4 Consequences of absence/non-submission of tasks If a learner's practical assessment task is incomplete or unavailable with valid reason, the learner may be given three weeks before the commencement of the final end-of-year examination to submit the outstanding task. Should the learner fail to fulfil the outstanding PAT requirement, such a learner will be awarded a zero mark for that PAT component. A learner's results are regarded as incomplete if he/she does not offer any component of the PAT task. He/She will be given another opportunity based on the decision of the head of the assessment body. Should the learner fail to fulfil the outstanding PAT requirement, the marks for these components will be omitted and the final mark for Mechanical Technology will be adjusted for promotion purposes in terms of the completed tasks. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 5 DBE/PAT 2021 NSC 2.5 Declaration of Authenticity NAME OF SCHOOL: NAME OF LEARNER: (FULL NAME(S) AND SURNAME) NAME OF TEACHER: I hereby declare that the project submitted for assessment is my own, original work and has not been previously submitted for moderation. SIGNATURE OF CANDIDATE DATE As far as I know, the above declaration by the candidate is true and I accept that the work offered is his/her own. SIGNATURE OF TEACHER DATE SCHOOL STAMP Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 6 DBE/PAT 2021 NSC 3. LEARNER GUIDELINES Instructions to the learner  The PAT consists of a specialisation task in Fitting and Machining. The practical work is spread over three terms, as set out in this document. (See CAPS document.)  All tasks must be completed according to the time frames set out in each of the tasks.  Learners are requested to actively engage in all practical assessment tasks.  Learners who are uncooperative will receive demerits or a zero mark for that particular section of the work.  Learners who act unsafely in the workshop and place other learners in danger, will be given additional corrective tasks to improve their safety awareness. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 7 DBE/PAT 2021 NSC 4. SPECIALISATION FITTING AND MACHINING TASK: BENCH VICE FIGURE 1: EXPLODED ISOMETRIC DRAWING PARTS LIST PARTS QUANTITY MATERIAL 1. Base 1 Mild steel/Aluminium 2. Fixed jaw 1 Mild steel/Aluminium 3. Moving jaw 1 Mild steel/Aluminium 4. Jaw linings 2 Mild steel/Aluminium 5. Guide pins 2 Bright mild steel/Aluminium 6. M12 x 1,75 screw 1 Bright mild steel/Aluminium 7. Retaining washer 1 Mild steel/Aluminium 8. Handle set 1 Bright mild steel/Aluminium Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 8 DBE/PAT 2021 NSC Term: 1 to 3 Start date: January 2021 Completion date: August 2021 The following standards must be achieved:  All sizes must be within the given tolerance.  There must be no damage to tools and equipment.  All appropriate safety procedures must be adhered to.  The project must be well presented. RESOURCES REQUIRED FOR PAT: Consumable materials required per learner Quantity per No. of Total Part Material Dimensions learner learners quantity Mild steel/ Fixed jaw Aluminium 86 x 68 x 12 1 70 x 12 flat bar Mild steel/ Moving jaw Aluminium 86 x 68 x 12 1 70 x 12 flat bar Mild steel/ Jaw linings Aluminium 72 x 18 x 8 2 20 x 8 flat bar Bright mild steel/ Guide pins Aluminium 120 x 12 2 12 mm round bar Bright mild steel/ Screw Aluminium 145 x 20 1 20 mm round bar Bright mild steel/ Handle Aluminium 120 x 12 1 12 mm round bar Mild steel/ Base Aluminium ± 100 x 70 1 70 x 12 flat bar Mild steel/ Retaining Aluminium 20 x 2 1 washer 20 mm round bar Split pins Split pins 20 x 3 2 Countersink Bolts M6 x 1 x 12 4 screws Allen key cap Bolts M6 x 1 x 25 2 screws NOTE: This material list is NOT a cutting list. The teacher must determine and create the cutting list. Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 9 DBE/PAT 2021 NSC FIGURE A FIGURE B FIGURE C Allen key cap screws Countersink screws Split pin Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 10 DBE/PAT 2021 NSC FIGURE 2: FIXED JAW Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 11 DBE/PAT 2021 NSC FIGURE 3: MOVING JAW Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 12 DBE/PAT 2021 NSC FIGURE 4: JAW LININGS Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 13 DBE/PAT 2021 NSC FIGURE 5: BASE Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 14 DBE/PAT 2021 NSC FIGURE 6: SCREW, GUIDE PINS AND RETAINING WASHER Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 15 DBE/PAT 2021 NSC FIGURE 7: HANDLE SET Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 16 DBE/PAT 2021 NSC RUBRICS DRILLING AND TAPPING NOTE: Use RUBRIC A for the assessment of all holes to be drilled. RUBRIC A: DRILLING Assessment facet Mark Drilling of correct diameter of hole 1 Depth correctly drilled 1 Hole clean and without burrs 1 Hole perpendicular to work piece 1 Hole drilled to correct position on work piece 1 Subtotal: 5 NOTE: Use RUBRIC B for the assessment of all internal and external screw threads to be tapped. RUBRIC B: TAPPING OF SCREW THREADS Assessment facet Mark Correct screw thread cut 1 Screw thread perpendicular to work piece 1 Screw thread has no burrs on outside 1 Depth/Length tapped correctly 1 No defects (e.g. cross thread) 1 Subtotal: 5 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 17 DBE/PAT 2021 NSC TOLERANCES LENGTH AND DIAMETERS NOTE: On all the lengths and diameters candidates will lose 1 mark for every 0,1 mm deviation from the basic size. Use RUBRIC C for assessment of all lengths and diameters. RUBRIC C: LENGTHS AND DIAMETERS DEVIATION MARK DEDUCTIONS 0–0,1 -0 0,1–0,2 -1 0,2–0,3 -2 0,3–0,4 -3 0,4–0,5 -4 0,5 and more -5 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 18 DBE/PAT 2021 NSC MECHANICAL TECHNOLOGY FITTING AND MACHINING MARK SHEET – FIXED JAW (Part # 2) – PHASE 1 GRADE 12 DATE PROJECT BENCH VICE LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 Check 86 mm length 5 LENGTH Check 12 mm thickness 5 AND WIDTH Check 68 mm width 5 MILLING OF Milling 16 mm width 5 STEP Milling 4 mm deep 5 Ø5 Drilling of 4 x Ø5 mm holes 20 DRILLING (4 x 5) M6 TAPPING Tapping of 4 x M6 20 Ø10.2 Drilling of 3 x Ø10,2 mm holes 15 M12 Tapping of M12 x 1,75 5 TAPPING Milling of chamfer – 45° angle and 4 mm 5 Subtotal: 90 PHASE 1 TOTAL: 50 SIGNATURE OF TEACHER SIGNATURE OF SUBJECT HEAD SIGNATURE OF MODERATOR Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 19 DBE/PAT 2021 NSC MECHANICAL TECHNOLOGY FITTING AND MACHINING MARK SHEET – MOVING JAW (Part # 3) – PHASE 2 GRADE 12 DATE PROJECT BENCH VICE LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 Check 86 mm length 5 LENGTH AND Check 12 mm thickness 5 WIDTH Check 68 mm width 5 MILLING OF Milling 16 mm width 5 STEP Milling 4 mm deep 5 Drilling of 2 x Ø5 mm holes Ø5 DRILLING 10 (2 x 5) Tapping of 2 x M6 holes M6 TAPPING 10 (2 x 5) Ø8,5 Drilling of 2 x Ø8,5 mm holes 10 Ø12,5 Drilling of 1 x Ø12,5 mm hole 5 Tapping of 2 x M10 x 1,5 M10 TAPPING 10 (2 x 5) Milling of chamfer – 45° angle and 4 mm 5 Subtotal: 75 PHASE 2 TOTAL: 50 SIGNATURE OF TEACHER SIGNATURE OF SUBJECT HEAD SIGNATURE OF MODERATOR Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 20 DBE/PAT 2021 NSC MECHANICAL TECHNOLOGY FITTING AND MACHINING MARK SHEET – SCREW (Parts # 6 and 7) – PHASE 3 GRADE 12 DATE PROJECT BENCH VICE LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 Total 150 mm length 5 30 mm length of Ø20 section 5 LENGTH Ø12 to a total length of 120 mm 5 Check back of hexagon to be 5 19 mm length at Ø12 section Calculate cutting depth of screw 4 thread CUTTING SCREW Screw thread depth cut correctly 5 THREAD Screw thread to a length of 101 mm 5 Screw thread cut cleanly (no tears) 3 Calculate cutting depth of hexagon 4 Cut to correct depth 5 HEXAGON All sides equal to size 6 Chamfering of hexagon 3 Drilling of 2 x Ø3 holes (2 x 5) 10 DRILLING 15 mm distance of Ø8,5 hole 5 Ø20 diameter 5 RETAINING Inside hole – Ø12,5 5 WASHER Parting to a thickness of 2 mm 5 Subtotal: 85 PHASE 3 TOTAL: 50 SIGNATURE OF TEACHER SIGNATURE OF SUBJECT HEAD SIGNATURE OF MODERATOR Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 21 DBE/PAT 2021 NSC MECHANICAL TECHNOLOGY FITTING AND MACHINING MARK SHEET – PARTS (Parts # 1, 4, 5 and 8) – PHASE 4 GRADE 12 DATE PROJECT BENCH VICE LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 Check 72 mm length 5 Check width of 18 mm 5 Jaw 1 Drilling of 2 x Ø6 mm holes 10 JAW LININGS Countersink hole 2 Create clamping surface 3 Check 72 mm length 5 Check width of 18 mm 5 Jaw 2 Drilling of 2 x Ø6 mm holes 10 Countersink hole 2 Create clamping surface 3 Subtotal: 50 Total length of 120 mm 5 Guide pin 1 Size: Ø10 mm 5 Cut M10 screw thread 8 mm long 5 GUIDE PINS Cut 2 x flat surfaces 1 mm deep 5 Total length of 120 mm 5 Guide pin 2 Size: Ø10 mm 5 Cut M10 screw thread 8 mm long 5 Cut 2 x flat surfaces 1 mm deep 5 Subtotal: 40 Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 22 DBE/PAT 2021 NSC Sliding part: Cut Ø8: 108 mm long 5 Sliding part: Cut M8 thread: 10 mm 5 long Sliding part: Cut Ø12: 12 mm long 5 HANDLE SET Turn loose head to Ø12 mm 5 Turn loose head to 12 mm length 5 Drill loose head to M8 tapping size 5 Tap M8 screw thread 5 Subtotal: 35 Check 84 mm length 5 Check 74 mm width 5 BASE Drilling of 2 x Ø6 mm holes (2 x 5) 10 Countersink 2 x Ø12 (2 x 5) 10 Subtotal: 30 Safety 5 Finish 5 ASSEMBLY Composition 5 Presentation 5 Subtotal: 20 Subtotal: 175 PHASE 4 TOTAL: 100 SIGNATURE OF TEACHER SIGNATURE OF SUBJECT HEAD SIGNATURE OF MODERATOR Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 23 DBE/PAT 2021 NSC MECHANICAL TECHNOLOGY FITTING AND MACHINING MARK SHEET – TOTALS GRADE 12 DATE PROJECT BENCH VICE TOTALS LEARNERS MARKS FACETS 1 2 3 4 5 6 7 8 9 10 PHASE 1 50 PHASE 2 50 PHASE 3 50 PHASE 4 100 TOTAL: 250 TOTAL PAT MARK: 100 SIGNATURE OF TEACHER SIGNATURE OF SUBJECT HEAD SIGNATURE OF MODERATOR Copyright reserved Please turn over

Downloaded from hlayiso.com Mechanical Technology: Fitting and Machinery 24 DBE/PAT 2021 NSC 5. CONCLUSION On completion of the practical assessment task learners should be able to demonstrate their understanding of the industry, enhance their knowledge, skills, values and reasoning abilities as well as establish connections to life outside the classroom and address real-world challenges. The PAT furthermore develops learners' life skills and provides opportunities for learners to engage in their own learning. Copyright reserved