Skip to content

Mechanical Technology Grade 12 NSC Supplementary 2018 Memo

MemorandumMechanical TechnologyGrade 12201821 pages

Grade 12 Mechanical Technology memorandum from the NSC Supplementary Exam 2018 (English), 21 pages. Read online or download the free PDF.

Free to read online, no sign-up needed

Loading document…

Loading document…

Document textSearch extracted text and jump to a page.
Downloaded from hlayiso.com NATIONAL SENIOR CERTIFICATE GRADE 12 MECHANICAL TECHNOLOGY FEBRUARY/MARCH 2018 MARKING GUIDELINES MARKS: 200 These marking guidelines consist of 21 pages. Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 2 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 1: MULTIPLE-CHOICE QUESTIONS 1.1 C (1) 1.2 C (1) 1.3 B (1) 1.4 D (1) 1.5 C (1) 1.6 D (1) 1.7 A (1) 1.8 A (1) 1.9 A (1) 1.10 B (1) 1.11 A (1) 1.12 C (1) 1.13 B (1) 1.14 A (1) 1.15 D (1) 1.16 A (1) 1.17 C (1) 1.18 A (1) 1.19 B (1) 1.20 A (1) [20] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 3 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 2: SAFETY 2.1 Spring tester  Use correct attachments of the valve spring tester to compress  the spring.   Do not exceed the prescribed pressure.   Ensure that the spring does not slip out.  (ANY 2 x 1) (2) 2.2 Welding helmet  To protect your eyes against the dangerous ultra-violet rays.   To protect your skin against the dangerous ultra-violet rays.   To protect your eyes against the sparks.   To protect your skin against the sparks.  (ANY 1 x 1) (1) 2.3 Spot welding  To prevent the electrodes from overheating.  (1) 2.4 Testers 2.4.1 Brinell tester  The tester must be mounted on the rigid spot on a workbench   The force must be applied at an angle of 90° to the test piece   Do not exceed the prescribed load   Make sure the test piece is placed securely into position  (ANY 1 x 1) (1) 2.4.2 Tensile tester  Make sure all safety guards are in place   Do not exceed the prescribed load   See that the test piece is securely placed in position   Make sure the dial indicator is mounted properly  (ANY 1 x 1) (1) 2.4.3 Torsion tester  Fasten the tester to the workbench   When you add pieces of different mass, you should attach them very gently otherwise you could get a skew reading of the torsion on the rod   Get specification (torsion) of the different materials and of the size rods you would like test  (ANY 1 x 1) (1) 2.5 Bearing puller  Perpendicular or 90° to the bearing.  (1) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 4 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 2.6 Cylinder leakage tester 2.6.1  To prevent damage to the seals and tester   To ensure the correct reading  (ANY 1 x 1) (1) 2.6.2  To prevent damage to the tester and spark plug hole or injector hole   To ensure the correct reading  (ANY 1 x 1) (1) [10] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 5 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 3: TOOLS AND EQUIPMENT 3.1 Testers 3.1.1 Cylinder leakage tester  Is used to determine a leakage in the cylinder.  Determine the volume of leakage (2) 3.1.2 Fuel pressure tester  Is used to test the fuel operating pressure in the system   Is used to test the fuel pressure in the fuel line that runs to the direct injection.  (2) 3.1.3 Torsion tester  Is used to investigate the relationship between momentum or torque applied to material   Is used to investigate influence of material length on torsional deflection.  (2) 3.2 Reasons for high CO2 reading  Lean fuel mixture setting   Low compression   Faulty high tension leads  (ANY 2 x 1) (2) 3.3 MIGS/MAGS-welding 3.3.1 Reasons for using inert gas during MIGS/MAGS welding  Stabilises the arc on the parent metal   Shields the arc and weld pool from atmospheric gases like oxygen  (2) 3.3.2 Advantages of MIGS/MAGS welding  Can weld in any position   Less operator skill required   Continuous welding can be done   Causes less deformation   Faster than arc welding   Minimal post weld cleaning   No slag removal is required  (ANY 2 x 1) (2) [12] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 6 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 4: MATERIALS 4.1 Characteristics of structures 4.1.1 Austenite  Soft   Coarse grain structure   Non-magnetic  (ANY 2 x 1) (2) 4.1.2 Ferrite  Soft   Ductile   Magnetic  (ANY 2 x 1) (2) 4.2 Iron-carbon equilibrium diagram 4.2.1 Lower critical point (AC1) of steel  The structure starts to change  (2) 4.2.2 Higher critical point (AC3) of steel  The structure turns into complete Austenite   The steel completely loses its magnetic properties   The structure turns into its finest grain size  (ANY 1 x 2) (2) 4.3 Reasons to enhance properties of a crankshaft  To produce a hard face with a tough core.   To induce toughness  (2) 4.4 Reasons for the tempering of a camshaft  To increase the lifespan of the camshaft   To eliminate brittleness caused by hardening.  (ANY 2 x 1) (2) 4.5 Heat treatment process on piston rings  Hardening  (1) [13] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 7 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 5: TERMONOLOGY 5.1 Key dimensions 5.1.1 The width of the key D Width  4 120   4  30 mm  (2) 5.1.2 The thickness of the key D Thickness  6  120  6  20 mm  (2) 5.1.3 The length of the key Length  D  1.5   120  1.5  180 mm  (2) 5.2 Indexing 40 Indexing  n 40 2    124 2 20   62 No full turns and 20 holes in a 62 hole circle  (3) 5.3 Height of screw the screw thread H  0.866 P  0.866  3   2.6 mm  (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 8 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 5.4 Gear terminology 5.4.1 Addendum =m = 3 mm  (1) 5.4.2 Dedendum = 1,157 m or =1,25 m = 1,157 x 3  =1,25 x 3  = 3,47 mm  =3,75 mm  (2) 5.4.3 Clearance = 0,157 m or =0,25m = 0,157 x 3  =0,25 x 3  = 0,47 mm  =0,75 mm  (2) 5.4.4 PCD Module  T PCD  m  T   3  48  144mm  (2) 5.4.5 OD = PCD + 2m  = 144 + 2(3) = 144 + 6 = 150 mm  (2) 5.4.6 Cutting depth = 2,157 m  or =2,25m  = 2,157 x 3 =2,25 x 3 = 6,47 mm  =6,75 mm  (2) 5.4.7 Circular pitch = m x 𝜋  =3x𝜋 = 9,42 mm  (2) 5.5 Setting of the lathe and cutting tool to cut a metric V-screw thread:  Set the lathe to the correct speed for screw cutting   Set the lead screw according to the required pitch   Set the dial gauge to position with the required worm gear   Set the compound slide to half the included angle of the thread (30°)   Set the cutting tool centre height and 90° to the work piece with the help of a centre gauge   Set cross slide and compound slide collars to zero with the tool touching the work piece  (6) [30] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 9 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 6: JOINING METHODS 6.1 Welding defects 6.1.1 Slag inclusion  Welding speed too fast   Not removing the slag from the previous weld run before welding the next run   Current too low  (ANY 2 x 1) (2) 6.1.2 Incomplete penetrations  Welding speed too fast   Faulty joint design   Electrode too large   Current too low  (ANY 2 x 1) (2) 6.2 Atmospheric contamination during MIGS/MAGS welding  Inadequate shielding gas flow   Excessive shielding gas flow   Severely clogged nozzle   Damaged gas supply system   Excessive wind in the welding area  (ANY 2 x 1) (2) 6.3 Nick break test  Make a hacksaw cut at both edges, through the centre of the weld   Place the saw-nicked specimen on two steel supports   Use a sledge hammer to break the specimen by striking it in the zone where you made the saw cuts   Defects like incomplete fusion, slag inclusion and brittleness will be exposed in the break   Any defects bring it to the attention to the welder to rectify it  (5) 6.4 Reasons for destructive tests 6.4.1 Bend test To determine the ductility/elongation  of the weld metal. (2) 6.4.2 Machinability test To determine the welds hardness  and its strength.  (2) 6.5 X-ray test To detect internal defects in the weld metal (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 10 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 6.6 Weld crater Forms where welding is resumed at the bottom of the previous weld instead of on the top  (2) 6.7 MIGS/MAGS welding 6.7.1 Welding process MIGS/MAGS welding  (1) 6.7.2 Labelling A. Parent metal  B. Arc  C. Electrode wire  D. Gas shroud  E. Shielding gas  (5) [25] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 11 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 7: FORCES 7.1 Resultant 210cos60° 210 N 210sin60° 190 N 190cos40° 190sin40° 40° 60° 200 N 185 N ∑HC 200  210 cos 60 - 190 cos 40   200  105 - 145.55  (4)  159,45 N ∑VC 210 sin 60  190 sin 40  185   181,87  122,13  185  (3)  119 N OR Horizontal Magnitudes Vertical Magnitudes components components 200N 200 N  210NSin60 0 181,87N  210N 105 N  190NSin40 0 122,13 N  190N Cos40 0 -145,45 N  -185 N -185 N TOTAL 159,45 N  TOTAL 119 N  Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 12 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines E 2  HC 2  VC 2 E  159,45 2  119 2  159,45N E  198,96 N  36,74° 119N (3) E VC Tan θ   HC 119  159,45  36,73  E  198,96N 36,73south of west OR  36 44' minutes south of west  (3) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 13 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 7.2 Stress and Strain 7.2.1 Resistance area A  π D2  d 2   4   π 0,056 2  0,038 2  4 3  1,33  10 m 2  (2) 7.2.2 Stress force  Stress  area 20 10 3 Stress   1,33 10 3 15037593,98 Pa Stress  15,04 MPa  (3) 7.2.3 Strain Δl Strain   OL 50 - 49 ,975  Strain  50 0 ,025 Strain  50  0 ,5  10 3  (3) 7.2.4 Young’s Modulus of Elasticity Stress Youngs Modulus of Elasticity   Strain 15,04 10 6  Ε 0 ,5 10 3  30 ,08 10 9 Pa  30 ,08GPa  (3) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 14 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 7.3 Moments 7.3 600 N 300 N 850 N 1,5 m 1,5 m 3m 3m A B Calculate B. Moments about A:  LHM   RHM  B  6  300  1,5  850  3  6 B 3000  6 6 B  500 N  Calculate A. Moments about B:  RHM   LHM   A  6  850  3  300  4,5  600  6  6 A  2550  1350  3600 6 A 7500  6 6 A 1250 N  (6) [30] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 15 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 8: MAINTENANCE 8.1 Reason using SAE 20W50 This to ensure that the oil is able to satisfy the operational  requirements over a range of temperature  from start-up to running hot. (2) 8.2 Maintain V-belt drive systems  Check the contact surfaces of the pulley to prevent the belt from being damaged.  Check the belt condition and replace if it is worn.   Correct installation procedure must be followed.   Belt drives should be well guarded to prevent foreign objects to come into contact with the belts and pulleys.   Keep guard mesh free of papers, rags, etc. that can cause insufficient air flow.   Check that the belt deflection is according to specification.   Store replacement belts in a cool, well ventilated place.   Correct alignment of pulleys.  (ANY 2 x 1) (2) 8.3 Flash point It is the lowest temperature  at which the oil gives off vapours  which can ignite.  (3) 8.4 Maintaining cutting fluid  Avoid contamination of the cutting fluid by draining and regularly replacing it.   Always clean the machine's splash tray of metal cutting after use.   Regularly wipe cutting fluid splashes of machine parts.   Ensure that the sump is topped up from time to time and check that there is sufficient flow of cutting fluid to the cutting tool.  (ANY 2 x 1) (2) 8.5 Functions of the clutch plate  It provides friction between the flywheel and pressure plate.   It serves as a link between the clutch and the gearbox main shaft.  (2) 8.6 Reasons for skimming the flywheel  To remove the grooves caused by the clutch plate.   To ensure a full contact surface between the flywheel and the clutch plate.   To prolong the life of the clutch plate.  (ANY 2 x 1) (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 16 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 8.7 Properties of grease  It must be water resistant, it must not mix with water   Prevents rust/corrosion   Good for load pressures   High melting point   Low freezing point   Prevent gumming   Be able to lubricate   High viscosity  (ANY 2 x 1) (2) [15] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 17 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 9: SYSTEMS AND CONTROL 9.1 Gear drives 9.1.1 Rotation frequency of input shaft N A TB  TD  TF  N F TA  TC  TE TB  TD  TF  N F  NA = TA  TC  TE 36  46  80  160 =  20  18  42 = 1401,90 r/ min  (3) 9.1.2 Velocity ratio N VR = A NF  1401,90 VR = 160 = 8,76:1  (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 18 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 9.2 Belt drives 9.2.1 Rotation frequency of driver pulley N DR×DDR =N DN×DDN N DN  DDN  N DR = DDR 733,33×0,36 =  0 ,24 = 2000r/ min  (3) 9.2.2 Power transmitted T  T πDn P= 1 2 60 ( 360  90 ) π  0,36  733,33 P=  60 = 3732,20Watts = 3,73 kW  (2) 9.2.3 Belt speed πDN Belt speed  60  π  0 ,36  733,33  60  13,83m.s1  (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 19 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 9.3 Hydraulics 9.3.1 Fluid pressure πD 2 AB = 4 π 0 ,04 2  = 4 =1,26×10 - 3 m 2  F PB = AB  275 =  1,26×10 - 3 =218253,97 Pa or  = 218,25 kPa (5) 9.3.2 Diameter of piston B PB = PA F PB  B AB F AB  B  PB 5,56  10 3 AB  218,25  10 3  AB  25,48  10  3 m 2 πD 2 AB  4 AB  4 DB  π 25,48  10  3  4   π  0,18 m or   180 mm (4) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 20 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines 9.4 ABS ABS prevents wheels from skidding  when breaking hard  in difficult conditions. (2) 9.5 ECU Electronic Control Unit  (1) 9.6 Traction Control  Prevent wheels from spinning.   Improves road holding  (ANY 1 x 1) (1) [25] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology 21 DBE/Feb.–Mar. 2018 NSC – Marking Guidelines QUESTION 10: TURBINES 10.1 Reaction turbines  Francis   Kaplan   Tyson   Gorlov  (ANY 2 x 1) (2) 10.2 Supercharger boost Boost refers to the increase in intake manifold pressure  that exceeds normal atmospheric pressure (2) 10.3 Blowers  Roots   Centrifugal   Vane-type   Twin screw type  (ANY 2 x 1) (2) 10.4 Gas turbine A = Clean air inlet  B = Compression  C = Combustion  D = Exhaust  E = Turbine  F = Combustion chamber  (6) 10.5 Application of a gas turbine  Jet engines   Naval ships   Hi-performance vehicles and boats   Generating electricity  (ANY 2 x 1) (2) 10.6 Advantages of a gas turbine  Less complex than internal combustion piston engines   Only one moving part (Common shaft for: compressor and turbine)   Operate at higher revolutions per minute  (ANY 2 x 1) (2) 10.7 Waste gate A waste gate is a valve that diverts exhaust gases away from the turbine wheel  to regulate the turbine/compressor speed and boost. (2) 10.8 Oil cooler To cool the oil  that lubricates the turbocharger bearings and shaft.  (2) [20] TOTAL: 200 Copyright reserved

Study this subject

More from Grade 12 Mechanical Technology

View all