Downloaded from hlayiso.com
NATIONAL
SENIOR CERTIFICATE
GRADE 12
MECHANICAL TECHNOLOGY
FEBRUARY/MARCH 2016
MEMORANDUM
MARKS: 200
This memorandum consists of 18 pages.
Copyright reserved Please turn over
Skip to contentAll 2016 papers 





View all
%20Eng--5d2e2bd0-b02f-4218-849f-e7933bc6c4d1/v1-2dba8a1dc6758c98b205/card.webp)
%20Afr--1e7205e4-aef1-4cc4-afdf-aac93562ae67/v1-094abcfa5c3eff1cb995/card.webp)
%20MG%20Afr--552ebeca-d294-4c37-b3fb-cded79fa438f/v1-b698b76db92c8affef7e/card.webp)
%20Eng--10859467-be3e-41fb-aee0-b797c385437d/v1-986e8982bfb6b966a34d/card.webp)

Mechanical Technology Grade 12 NSC Supplementary 2016 Memo
Grade 12 Mechanical Technology memorandum from the NSC Supplementary Exam 2016 (English), 18 pages. Read online or download the free PDF.
Mechanical Technology · Grade 12 · NSC Supplementary Exam · 2016. Memorandum, 18 pages. Read online or download the PDF.
- Subject
- Mechanical Technology
- Grade
- Grade 12
- Document type
- Memorandum
- Year
- 2016
- Exam period
- NSC Supplementary Exam
- Curriculum
- CAPS
- Pages
- 18
- File size
- 503.5 KB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 18
This exam
NSC Supplementary Exam 2016
Document textSearch extracted text and jump to a page.
Downloaded from hlayiso.com
Mechanical Technology 2 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 1: MULTIPLE-CHOICE QUESTIONS
1.1 C (1)
1.2 B (1)
1.3 D (1)
1.4 D (1)
1.5 A (1)
1.6 C (1)
1.7 D (1)
1.8 D (1)
1.9 B (1)
1.10 D (1)
1.11 D (1)
1.12 C (1)
1.13 B (1)
1.14 B (1)
1.15 A (1)
1.16 C (1)
1.17 A (1)
1.18 C (1)
1.19 D (1)
1.20 B (1)
[20]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 3 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 2: SAFETY
2.1 Safety – Centre lathe
• Look out for revolving work pieces
• Do not remove shavings by hand
• Be careful not to run the cutting tool into the chuck
• Do not make any adjustments on the work piece while the machine is
running
• Do not leave tools on the machine while in operation
(Any 2 x 1) (2)
2.2 Safety – Tensile Tester
• Use safety goggles
• Do not apply excessive pressure
• Test piece to be well secured for testing
• Check hydraulic fluid level
(Any 2 x 1) (2)
2.3 Safety – Spring Tester
• Spring tester should be in a good condition
• Spring tester must be fitted correctly and firmly
• Ensure that the spring cannot slip out of position before applying the load
• An uniform load must be applied
• Release the load carefully and uniformly
(Any 2 x 1) (2)
2.4 Safety – Cylinder Leakage
• Clean the area around the spark plug, before removing the spark plug
To prevent dirt from falling into the cylinder.
• Be careful when removing radiator cap
The water may be hot and under pressure.
• Do not exceed the specified pressure to test the cylinder
To prevent damage to the seals and tester.
• The tester must fit properly and be well tightened in the spark hole or
injector hole
To prevent damage to the tester and spark hole or injector hole.
Any 2 x 2 (4)
[10]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 4 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 3: TOOLS AND EQUIPMENT
3.1 Compression testing
3.1.1 • Wet compression test
• Dry compression test (2)
3.1.2 • Worn cylinders
• Worn piston rings
• Worn piston
• Leaking inlet valve
• Leaking exhaust valve
• Leaking cylinder head gasket
(Any 2 x 1) (2)
3.2 Oil pump
• Oil pressure meter or oil pressure tester (1)
3.3 Cooling system test
• Remove the radiator cap and fit the tester
• Pump air at the prescribed pressure into the system
• Note the reading and if the reading drops, it indicates a leaking
system
• To test for a leaking cylinder-head gasket, the engine is started.
• If the reading increases while the engine idles, it indicates on a leaking
cylinder-head gasket (7)
[12]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 5 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 4: MATERIALS
4.1 Iron-carbon properties
4.1.1 Pearlite:
• Good ductility
• Hard
• Strong and tough
• Resistant to deformation
(Any 2 x 1) (2)
4.1.2 Cementite:
• Intensely hard
• Brittle. (2)
4.2 Critical points
4.2.1 AC 1 – lower critical point
• The lowest temperature to which steel must be heated to be
hardened.
• The lowest temperature where the structure starts to
change.
(Any 1 x 2) (2)
4.2.2 AC 3 – high critical point
• The highest temperature to which the steel can be heated to
obtain maximum hardness.
• The temperature where the steel completely loses its magnetic
properties.
• The temperature where the steel's structure is at its finest.
(Any 1 x 2) (2)
4.3 Carbon content determines the hardness of steel. (1)
4.4 Cementite structure in steel determines the hardness. (1)
4.5 Ferrite structure in steel determines the ductility. (1)
4.6 Austenite is a solid solution of iron and carbon also called iron carbide.
The structure is at its finest. (2)
[13]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 6 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 5: TERMINOLOGY
5.1 Gear calculation
5.1.1 Circular pitch = m × π
circular pitch
module =
π
12,567
=
π
= 4 mm (3)
5.1.2 Outside diameter = PCD + 2m
PCD = OD − 2m
= 112 − 2(4 )
= 104 mm (3)
5.1.3 Cutting Depth = 2,157m Cutting Depth = 2,25m
Cutting Depth = 2,157 × 4 OR Cutting Depth = 2,25 × 4
= 8,628mm = 9 mm
= 8,63 mm (2)
5.1.4 Addendum = m
= 4 mm (1)
5.1.5 Dedendum = 1,157m Dedendum = 1,25m
= 1,157 × 4 OR Dedundum = 1,25 × 4
= 4,628mm = 5 mm
= 4,63 mm (2)
5.1.6 Clearance = 0,157m Clearance = 0,25m
= 0,157 × 4 OR = 0,25 × 4
= 0,628 mm = 1 mm
= 0,63 mm (2)
5.1.7 PCD
module =
Teeth
PCD
Teeth =
m
104
=
4
= 26 teeth (3)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 7 DBE/Feb.–Mar. 2016
NSC – Memorandum
5.2 Indexing
40
Indexing =
n
40
=
26
40 2
= ÷
26 2
20
=
13
7 3
=1 ×
13 3
21
=1
39
Indexing = 1 full turn of the crank and 21 holes on the 39 hole circle
(4)
5.3 Screw thread cutting
• Set up the work piece in the lathe and turn the part to be threaded to
the major diameter of the thread.
• Set the compound slide to the correct angle (30°) to the right and set
the tool up accurately in the post.
• Consult the index plate of the quick-change gearbox for 2 mm pitch
and move the levers accordingly.
• Start the lathe and set the cutting tool so that it just touches the work
piece. Set graduated dials to zero (cross feed and compound slide)
• Move cutting tool a short distance off end of work piece and feed
compound slide say 0,06 mm inwards.
• With lathe turning, engage half nuts at the correct line on the chasing
dial, putting the first cut in progress.
• Withdraw the cutting tool quickly and disengage the half-nut lever.
Return the carriage to the starting point of the thread. OR Stop the
machine, leave half nut engaged, back off slide past zero and return
carriage to start position in reverse
• Check with thread gauge to see if thread pitch is correct.
• Repeat with successive cuts until thread is complete. (Remember to
bring cross-feed collar back to zero for each cut)
• Each successive cut is set by means of the compound slide. Check
thread with ring gauge for correct fit. (10)
[30]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 8 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 6: JOINING METHODS
6.1 MIG/MAGS welding equipment
6.1.1 MIG/MAGS welding equipment (1)
6.1.2 Labels
A = Shielding gas cylinder
B = Regulator
C = Gas flow meter
D = Continuous wire reel
E = Welding gun
F = Arc
G = Earth clamp (7)
6.1.3 Purpose
Prevents oxygen to come in contact with the molten metal. (2)
6.2 Weld defects
6.2.1 Defect: Slag inclusion
Causes:
• Included angle is too narrow.
• Rapid chilling.
• Weld temperature is too low.
• High viscosity of molten metal.
• Slag from previous run weld not removed.
(Any 2 x 1) (2)
6.2.2 Defect: Undercutting
Causes:
• Faulty electrode manipulation.
• Current too high.
• Arc length too long.
• Speed of weld too fast.
(Any 2 x 1) (2)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 9 DBE/Feb.–Mar. 2016
NSC – Memorandum
6.3 Welding defects
6.3.1 Defect: Lack of fusion
Preventions:
• Adjust the electrode angle and prepare the V groove
properly.
• Weave must be sufficient to melt sides of the joint.
• Proper current will allow fusion.
• Adjust welding speed to ensure fusion.
(Any 2 x 1) (2)
6.3.2 Defect: Weld craters
Preventions:
• Use lower current.
• Use proper welding technique.
• Use correct electrode
(Any 2 x 1) (2)
6.4 Dye penetration test
• Clean the weld that needs to be tested.
• The dye is sprayed onto the clean surface.
• Allow the dye to penetrate the weld joint.
• Excess dye is cleaned away with a cleaning agent.
• Allow surface to dry thoroughly.
• Spray a developer onto the surface to bring out the dye trapped in the
crack.
• The dye will show all the surface defects (7)
[25]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 10 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 7: FORCES
7.1 Resultant
2,1
kN
1,5 kN
1,5cos40°
1,5sin40° 50°
40° 90° 4,7kN
50° 130°
3,1sin50°
3,1 kN 3,1cos50°
7.1.1 ∑ HC = 4,7 - 3,1cos50° - 1,5cos40°
= 4,7 - 1,99 - 1,15
= 1,56k N
7.1.2 ∑ VC = 2,1 + 1,5sin40° − 3,1sin50°
= 2,1 + 0,96 − 2,37
= 0,69 kN
7.1.3 Magnitudes 7.1.4 Magnitudes
Horizontal Vertical
components components
4,7 kN 4,7 kN 2,1 kN 2,1 kN
3,1 kN Cos50° -1,99 kN 1,5 kN Sin40 0 0,96 kN
1,5 kN Cos40° -1,15 kN 3,1 kN Sin50° -2,37 kN
TOTAL 1,56 kN TOTAL 0,69 kN
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 11 DBE/Feb.–Mar. 2016
NSC – Memorandum
E 2 = HC 2 + VC 2
E = 1,56 2 + 0,69 2
1,56kN
E = 1,71 kN
0,69kN
R
θ = VC 23,86°
Tan
HC
0,69
=
1,56
θ = 23,86 0
E = 1,71k N at 23,86 0 north from east (15)
7.2 Stress and Strain
Forces
π 2
Area = D
Force = load × gravity 4
= 600 ×10 π × 0,016 2
=
= 6000N 4
= 2,011× 10 − 4 m 2
Force
Stress =
Area
6000
=
2,011×10 − 4
= 29841551, 83 Pa
= 29,84 MPa
(6)
7.3 One Pascal (1 Pa) is equal to one Newton force (1 N) acting onto an
area of one square metre (1 m2) (3)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 12 DBE/Feb.–Mar. 2016
NSC – Memorandum
7.4 Reactions
Taking moments around A
=
(B × 3,5 ) + (1400 × 0,7 ) = (350 × 6,7 )2,65 + (1600 × 6)
3,5B + 980 =6214,25 + 9600
3,5B 6214,25 + 9600 − 980
=
3,5 3,5
B = 4238,36 N
Taking moments around B
=
(A × 3,5 ) + (1600 × 2,5 ) = (350 × 6,7 )0,85 + (1400 × 4,2 )
3,5A + 4000 = 1993,25 + 5880
3,5A 1993,25 + 5880 - 4000
=
3,5 3,5
A = 1106,64 N (6)
[30]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 13 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 8: MAINTENANCE
8.1 Routine maintenance.
• Tear on the belt.
• Misalignment of belt drive.
• Overheating of components.
• Belt slip.
• Belt wear.
• Pulley wear.
• Financial loss due to the damage suffered.
• Loss of valuable production time.
(Any 2 x 1) (2)
8.2 Cutting fluid
• To allow it to flow easily
• Dissipate excess heat
• Prevent excessive load on pump
(Any 2 x 1) (2)
8.3 Flash point
Is the lowest temperature at which the oil gives off a vapour which will
ignite. (2)
8.4 'API'
American Petroleum Institute (2)
8.5 Automatic transmission fluid
• Transmit power in the torque convertor
• Let hydraulic fluid transmit energy in order to move various parts such as
the servo unit.
• Acts as heat transfer medium to transfer heat within the transmission to
outside and assist in cooling it down.
• Acts as a lubricant for gears and bearings.
(Any 2 x 1) (2)
8.6 Replace belt in a drill press
• Machine should be switched off the locked out.
• Tension on the belt to be released by loosening an adjusting screw or
releasing the belt tensioner.
• Remove the belt.
• Replace with new belt of the correct type and size.
• The belt should be re-tensioned and aligned.
(5)
[15]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 14 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 9: SYSTEMS AND CONTROL
9.1 Gear drive
9.1.1 Rotational frequency of the electric motor:
NA TB × TD
=
ND T A × TC
80 × 63 × 2
NA =
30 × 40
10080
NA =
1200
N A = 8,4 r/s (5)
9.1.2 Speed ratio of gear train:
Input Driven teeth
Speed ratio = Speed ratio =
Output Driver teeth
8,4 80 63
= OR = ×
2 30 40
= 4,2 : 1 = 4,2 : 1 (2)
9.2 Belt drive
9.2.1 Diameter of the driven pulley
N1 × D1 = N2 × D 2
N2 × D 2
N1 =
D1
7,2 × 600
=
800
= 5,4 r/s (3)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 15 DBE/Feb.–Mar. 2016
NSC – Memorandum
9.2.2 Power transmitted:
T1
= 2,5
P = (T1 − Tπ
2) T2
Dn
π × 0,6 × 7,2
P =( 300 − 120) 300
T2 =
= 2442,90 Watt 2,5
= 2,44 kW = 120 N
OR
T1
= 2,5
P = (T1 − Tπ
2) T2
Dn
π × 0,8 × 5 ,4
P =( 300 − 120) 300
T2 =
= 2442,90 Watt 2,5
= 2,44 kW = 120 N (3)
9.3 The volume of gas can be changed by the altering of ...
• its pressure
• its temperature
• both its pressure and temperature
(Any 2 x 1) (2)
9.4 Definition of Boyle's law
The volume of a given mass of gas is inversely proportional to the
pressure on it, if the temperature remains constant (3)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 16 DBE/Feb.–Mar. 2016
NSC – Memorandum
9.5 Hydraulics
9.5.1 Fluid pressure
π 2
AA = D
4
π 2
= 0,04
4
= 1,26 × 10 -3 m 2
F
PA =
AA
80
= Pa
1,26 × 10 -3
= 63661,98 Pa
= 63,66 kPa
(3)
9.5.2 Diameter of piston B
PB = PA
FB
PB =
AB
FB
AB =
PB
320
AB =
63492,06
A B = 5,04 × 10 -3
π 2
A=D
4
AB × 4
DB = π
5,04 × 10 −3 × 4
= π
= 0,08 m
(4)
= 80 mm
[25]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 17 DBE/Feb.–Mar. 2016
NSC – Memorandum
QUESTION 10: TURBINES
10.1 Water turbine blades
To supply water pressure to the turbine (2)
10.2 Reverse flow
• Deriaz
• Francis (2)
10.3 Supercharger
• Roots
• Twin screw
• Centrifugal
• Vane
(Any 2 x 1) (2)
10.4 Turbocharger
• Exhaust gases drive the turbine
• The turbine drives a compressor via a common shaft
• The compressor forces compressed air above atmospheric pressure
into the cylinder
• Exhaust gases leave system through the exhaust pipe (5)
10.5 Supercharger over turbocharger
• Do not suffer lag
• More efficient at low revolution per minute.
• Does not require extensive exhaust modification.
• No special shutdown procedure is required.
(Any 2 x 1) (2)
10.6 Lag
Lag is the delay between pressing the accelerator pedal and feeling the
pressure building up. (3)
10.7 Supercharger drive
• Belt drive
• Gear drive
• Chain drive
(Any 2 x 1) (2)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Mechanical Technology 18 DBE/Feb.–Mar. 2016
NSC – Memorandum
10.8 Gas turbine disadvantages
• Cost is much greater than for a similar-sized reciprocating engine since
the materials must be stronger and more heat resistant.
• Manufacturing operations are also more complex.
• Usually less efficient than reciprocating engines, especially at idling
speed.
• Delayed response to changes in power settings.
(Any 2 x 1) (2)
[20]
TOTAL: 200
Copyright reserved
Study this subject
Recommended for this subject

Question paper
Mechanical Technology Grade 12 NSC Supplementary 2016 QP

Memorandum
Mechanical Technology Grade 12 Eastern Cape Mock 2016 Memo

Memorandum
Mechanical Technology Grade 12 NSC November 2016 Memo (Eng)

Memorandum
Mechanical Technology Grade 12 NSC Supplementary 2018 Memo

Question paper
Mechanical Technology Grade 12 Eastern Cape Mock 2016 QP

Question paper
Mechanical Technology Grade 12 NSC Supplementary 2018 QP
More from Grade 12 Mechanical Technology

Annual teaching plan
Gr 12 Weld Met ATP 2023 24
%20Eng--5d2e2bd0-b02f-4218-849f-e7933bc6c4d1/v1-2dba8a1dc6758c98b205/card.webp)
Question paper
Mechanical Technology Grade 12 November 2024 NSC QP (Eng)
%20Afr--1e7205e4-aef1-4cc4-afdf-aac93562ae67/v1-094abcfa5c3eff1cb995/card.webp)
Question paper
Mechanical Technology Grade 12 November 2024 NSC QP (Afr)
%20MG%20Afr--552ebeca-d294-4c37-b3fb-cded79fa438f/v1-b698b76db92c8affef7e/card.webp)
Memorandum
Mechanical Technology Grade 12 NSC June 2024 Memo (Afr)
%20Eng--10859467-be3e-41fb-aee0-b797c385437d/v1-986e8982bfb6b966a34d/card.webp)
Question paper
Mechanical Technology Grade 12 NSC June 2024 QP (Eng)

Memorandum